Engineering Commons^™

Accident Rates At Intersections, Kenneth R. Agent

Kentucky Transportation Center Research Report

The objectives of this study were to determine average accident rates tor various categories of at-grade intersections and to identify intersections having high accident rates. This involved locating intersections at two or more state-maintained highways and determining the appropriate volumes to use as well as locating the accidents occurring at any given intersection.

A procedure was developed to allow tor the identification of intersections having high or critical accident rates. A list at the intersections of two or more state-maintained roadways was developed. A total of 6,707 intersections were included in the file. Using county, route and milepoint information, accident …

Middle Terminal Cell Models For Efficient Over-The-Cell Routing, Siddharth Bhingarde

Masters Theses

In this thesis, we introduce a new class of cell models called Middle Terminal Models (MTM) which combines the advantages of existing cell models: BTM and CTM. This class contains the models 2MTM, 3MTM-V, and 3MTM+V depending on the number of metal layers and the permissibility of vias in over-the-cell areas. In MTM, two rows of terminals are located in the middle of the cell. This partitions over-the-cell area into three regions and allows allocation of more nets to over-the-cell area in congested channels. We prove that when vias are allowed over-the-cell, in "almost all" cases the MTM based layouts …

The Influence Of Reynolds Number And Atmospheric Effects On Aircraft Wake Vortices Near The Ground, Zhongquan Charlie Zheng

Mechanical & Aerospace Engineering Theses & Dissertations

Aircraft wakes represent potential hazards which can control aircraft spacing and thus limit airport capacity. Wake vortex trajectories and strengths are altered radically by interactions with the ground plane and by atmospheric conditions. This work has been concerned with developing more accurate numerical predictions. A two-dimensional, unsteady numerical-theoretical study is presented which has included viscous effects, the influence of stratification, crosswind and turbulence on vortex behavior near the ground plane, using a vorticity-streamfunction formulation.

A two-parameter perturbation procedure has been developed which uses analytic solutions for the initial flow field to accommodate the ground effect region in the numerical simulation. …

Cross-Cultural Issues In The Management Of German-Owned Business Subsidiaries In Hampton Roads, Teja Ulrich

Engineering Management & Systems Engineering Theses & Dissertations

'Culture' can be described as patterns of thinking, feeling and acting that distinguish one cultural group from another. Cultural diversity is therefore likely to introduce variety to organizations in which individuals from different national backgrounds are working together. Although this variety bears the potential for an improvement of the cognitive development in the organizations, managers of multicultural business organizations tend to perceive cultural diversity as a disadvantage. This thesis attempts to identify the impact of cultural differences between Germans and Americans on organizations in which German managers work with American employees. German managers of eight business subsidiaries in the Hampton …

An Analysis Of The Response Of A Buckled Beam With Fixed Ends To An Harmonic Base Excitation Using The Finite Element Method, Peter John O'Donoghue

Mechanical & Aerospace Engineering Theses & Dissertations

A finite element formulation is developed to analyze the large deflection vibration of a buckled isotropic beam. The beam is buckled mechanically by an applied end displacement, and the dynamic loading is derived from the forced periodic base motion. The principle of virtual work is used to derive the system equations of motion. A Newton-Raphson iteration routine modified for the case of an applied end displacement is used with the incremental equations of motion to determine static deflection. The 0l time numerical integration algorithm is applied to the system of equations of motion in physical coordinates to determine dynamic response …

A Performance Prediction Model For A Fault-Tolerant Computer During Recovery And Restoration, Rodrigo A. Obando

Electrical & Computer Engineering Theses & Dissertations

The modeling and design of a fault-tolerant multiprocessor system is addressed in this dissertation. In particular, the behavior of the system during recovery and restoration after a fault has occurred is investigated. Given that a multicomputer system is designed using the Algorithm to Architecture To Mapping Model (ATAMM) model, and that a fault (death of a computing resource) occurs during its normal steady-state operation, a model is presented as a viable research tool for predicting the performance bounds of the system during its recovery and restoration phases. Furthermore, the bounds of the performance behavior of the system during this transient …

Resource Utilization Model For The Algorithm To Architecture Mapping Model, Rakesh R. Patel

Electrical & Computer Engineering Theses & Dissertations

The analytical model for resource utilization, and the variable node time and conditional node model for the enhanced ATAMM model for a real-time data flow architecture, is presented in this research. The Algorithm To Architecture Mapping Model, ATAMM, is a Petri net based graph theoretic model developed at Old Dominion University, and is capable of modeling the execution of large-grained algorithms on a real-time data flow architecture. Using the resource utilization model, the resource envelope may be obtained directly from a given graph and, consequently, the maximum number of required resources may be evaluated. The node timing diagram for one …

Competitive Enzyme Immunoassay By Polyclonal Antibodies Against Organophosphorus Pesticides, Kuo-Lan Wen

Theses and Dissertations in Biomedical Sciences

Organophosphorus compounds (OPs) comprise one of the major classes of pesticides in use today because they are highly effective and less toxic. Because of their extensive use, there is a need for monitoring OPs in water and vegetables. Gas chromatography (GC) is the usual method for OPs screening, but it is time-consuming and has the high cost of instrumentation. The goal of this project was to find an easy method which was sensitive and had less instrumentation required to test OPs.

Microwells and microtubes were utilized as the solid-phase immobilization for the development of an enzyme immunoassay for OPs. A …

Navier-Stokes Simulation Of Quasi-Axisymmetric And Three-Dimensional Supersonic Vortex Breakdown, Hamdy A. Kandil

Mechanical & Aerospace Engineering Theses & Dissertations

Computational simulation of supersonic vortex breakdown is considered for internal and external flow applications. The interaction of a supersonic swirling flow with a shock wave in bounded and unbounded domains is studied. The problem is formulated using the unsteady, compressible, full Navier-Stokes equations which are solved using an implicit, flux-difference splitting, finite-volume scheme. Solutions are obtained for quasi-axisymmetric and three-dimensional flows. The quasi-axisymmetric solutions are obtained by forcing the components of the flowfield vector to be equal on two axial planes, which are in close proximity to each other. For the flow in a bounded domain, a supersonic swirling flow …

Longitudinal Study Of Plasma And Erythrocyte Selenium Levels In Type I Diabetic Children During Development And Treatment Of Ketoacidosis, Pi-Hsia Fan

Chemistry & Biochemistry Theses & Dissertations

Most studies on the biological activity of selenium have focused on its role at the active site in the ubiquitous enzyme, glutathione peroxidase (GSH-Px) which catalyzes the removal of hydrogen peroxide and organic hydroperoxides (1). A connection between selenium deficiency and a wide range of diseases in animals and humans has been reviewed (2). Development of various forms of human cancer (3), failure of the immune system (4), as well as some cardiovascular diseases (5) have been reported or suspected to correlate with selenium deficiency. However, the physiological function of selenium in these different diseases is not fully understood, and …

Grid Sensitivity For Aerodynamic Optimization And Flow Analysis, Ideen Sadrehaghighi

Mechanical & Aerospace Engineering Theses & Dissertations

An algorithm is developed to obtain the grid sensitivity with respect to design parameters for aerodynamic optimization. Two distinct parameterization procedures are developed for investigating the grid sensitivity with respect to design parameters of a wing-section as an example. The first procedure is based on traditional (physical) relations defining NACA four-digit wing-sections. The second is advocating a novel (geometrical) parameterization using spline functions such as NURBS (Non-Uniform Rational B-Splines) for defining the wing-section geometry. An inter-active algebraic grid generation technique, known as Two-Boundary Grid Generation (TBGG) is employed to generate C-type grids around wing-sections. The grid sensitivity of the domain …

Acoustical Boundary Location Through Texture Analysis Of Multibeam Bathymetric Sonar Data, Herb Barad, Andrews B. Martinez, Brian S. Bourgeois, Edit J. Kaminsky

Electrical Engineering Faculty Publications

Texture analysis is performed on multibeam sonar signal returns discriminated angularity by beamforming. A collection of fourteen texture features are computed via co-occurrence matrices and data reduction is then performed using a principal components transformation. Acoustical boundaries (boundaries between regions with homogeneous acoustical properties) are evident from the features. Results indicate that seafloor bottom characteristics can be extracted from these texture features.

A Study Of The Interface Between A Turbulent Boundary Layer And The Irrotational Free Stream, Shih-Chao Lin

Mechanical & Aerospace Engineering Theses & Dissertations

A mathematical model has been developed to simulate the events which occur at the interface between a turbulent boundary layer and the irrotational free stream. By assuming the streamwise velocity component of this interface to be constant and that the interface is uncontorted initially, the solution to the equations of motion is used to derive the position functions of a point element on the interface. This analysis is restricted to a fully developed incompressible turbulent boundary layer with zero pressure gradient. Vertical velocity disturbances which are periodic in the spanwise direction and restricted to small streamwise domains are assumed.

The …

Effects Of Radiative Interactions In Molecular Gases Under Local And Nonlocal Thermodynamic Equilibrium Conditions, Manoj Kumar Jha

Mechanical & Aerospace Engineering Theses & Dissertations

Basic formulations, analyses, and numerical procedures are presented to investigate radiative heat interactions in diatomic and polyatomic gases under local and nonlocal thermodynamic equilibrium conditions. Essential governing equations are presented for both gray and nongray gases. Information is provided on absorption models, relaxation times, and transfer equations. Radiative flux equations are developed which are applicable under local and nonlocal thermodynamic equilibrium conditions.

The problem is solved for fully developed laminar incompressible flows between two parallel plates under the boundary condition of a uniform surface heat flux. For specific applications, three diatomic and three polyatomic gases are considered. The results are …

Analysis Of Pultrusion Processing For Long Fiber Reinforced Thermoplastic Composite System, Wen Tso

Mechanical & Aerospace Engineering Theses & Dissertations

Pultrusion is one of the composite processing technology, commonly recognized as a simple and cost-effective means for the manufacturing of fiber-reinforced, resin matrix composite parts with different regular geometries. Previously, because the majority of the pultruded composite parts were made of thermosetting resin matrix, emphasis of the analysis on the process has been on the conservation of energy from various sources, such as heat conduction and the curing kinetics of the resin system. Analysis on the flow aspect of the process was almost absent in the literature for thermosetting process. With the increasing uses of thermoplastic materials, it is desirable …

Robot Force Velocity Control Using Expert System For Control Mode Changes, William R. Doggett

Electrical & Computer Engineering Theses & Dissertations

The most important property of an automated mechanical system is reliable execution of a specified task. Automated mechanical systems work best in precisely structured environments where all operations are repeatable. Typically, these systems are difficult to modify and expensive to install. Sensors can be used to detect disturbances, thus reducing hardware cost by offsetting the need for precise rigid construction components. Sensors, however, increase the complexity and cost of the control software. Efficient methods of reacting to sensor information during automated system operation are required to reduce software complexity and expense.

This thesis analyzes a robotic construction task and describes …

The Effects Of Electron Radiation On The Glass Transition Temperature Of A Polyetherimide, Kristen Tulloch Kern

Physics Theses & Dissertations

The effects of electron radiation on a polyetherimide (PEI), Ultem*, were investigated. In particular, the changes in the glass transition temperature (T_g) with absorbed radiation dose were studied. The polymer was exposed to mono-energetic beams of 100-keV electrons and 1.0-MeV electrons for doses up to 100 megagray (MGy). Dosimetry for the exposures was based on Monte-Carlo simulations of the transfer of energy from an energetic electron to the polymer and on comparison to Nylon standards. Dynamic mechanical analysis was used to determine the (T_g) for non-exposed PEI and the changes in (T_g) resulting from …

Utilization And Cost Effectiveness Of Retread Tires, L. John Fleckenstein, David L. Allen

Kentucky Transportation Center Research Report

This report discusses the possible utilization and east effectiveness of using retreaded tires on state vehicles in Kentucky. Included is information obtained from a telephone survey of local companies and two state Dot agencies. Information was also obtained from a survey conducted on the AASHTO-VAN computer network. This report also contains a cost comparison of retread prices versus new tire prices.

A Sociotechnical Approach To The Study Of Semiautonomous Work Group Communication In Technical Organizations, Elizabeth B. Varnes

Engineering Management & Systems Engineering Theses & Dissertations

The sociotechnical aspects of group communication in semiautonomous technical work teams were investigated to understand how team members define "effective" group communication and what impact technical tools have on the group communication process. A team of workers with various technical backgrounds was selected for study. The study involved videotaped group sessions, a group training educational briefing and individual group member questionnaires. The results indicate that group members believed sharing information among group members was critical to successful communication and that certain technical tools could be effective during group meetings. The findings are congruent with the general theory that group communication …

Statistical Variations In Beach Parameter Change Rates For Walled And Non-Walled Profiles At Sandbridge, Virginia, Douglas Allen Bellomo

Civil & Environmental Engineering Theses & Dissertations

The interaction of seawalls {bulkheads) and beaches is a highly controversial subject today. In many locations all over the United States, seawalls have been both praised and ridiculed. It is well documented that Sandbridge, Virginia is, and has been, experiencing shoreline recession. Many believe however, that the recent construction of the seawalls has worsened this existing situation.

Fortunately, historical maps, and beach profiles are available to help determine if this is truly the case. The following defines several visible beach parameters, and describes how these parameters were calculated from two different data sources. Several methods and statistical techniques are then …

Bs News

Building Services Engineering

No abstract provided.

Elasto-Plastic Analysis Of Buried Pipelines Subjected To The Large Fault Movement, Luo-Jia Wang

Civil & Environmental Engineering Theses & Dissertations

The responses of buried pipelines subjected to a large fault movement are examined based upon a new non-linear cantilever beam analogy. This analogy assumes that the pipeline in the large deformation zone behaves like a cantilever beam subjected to a transversely concentrated shear at the inflection point and a uniformly distributed soil pressure along the entire span. Tangent modulus approach is adopted to analyze the coupled axial force-bending moment interaction effect on pipeline deformation in the inelastic range. Parametric studies of both tensile and compressive responses of buried pipeline to various fault movements, crossing angles, buried depths, pipe diameters and …

Silicon Carbide/Electroless Nickel Composite Plating For Aluminum Substrates, Ben Charbit

Masters Theses

The effectiveness of producing a composite coating by suspending micron-sized particles in an electroless nickel bath while plating a 2024T4 aluminum alloy part was studied. The variation in the count of particles trapped in the nickel coating due to changes in the particle size, concentration of the particles in the bath, and the substrate surface texture was also studied. Particle sizes of 1 micron and 10 microns, concentrations of 15 gr/lt and 30 gr/lt, and polished and blasted textures were used. It was found that this technique is an effective way to produce composite coatings rendering a high number of …

Simulation Model For Predicting The Impact Of Progressive Diseases In The U.S. Population By Tracking, Biju Suseelan

Masters Theses

Computer Aided Simulation is the process of designing a mathematical-logical model of a real system and experimenting with this model on a computer. Simulation encompasses a model building process as well as the design and implementation of an appropriate experiment involving that model. A simulation experiment involves observing the dynamic behavior of a model by moving from state to state in accordance with well-defined operating rules designed into the model. This research contains the development of a novel approach for the HIV transmission dynamics by using computer simulation to track the HIV positive individuals in a population and to determine …

Robust Control Of Nonlinear Multibody Flexible Space Structures, Atul G. Kelkar

Mechanical & Aerospace Engineering Theses & Dissertations

A generic nonlinear math model of a multibody flexible system is developed. Asymptotic stability of such systems using dissipative compensators is established. It is proved that, under certain conditions, this class of systems exhibit global asymptotic stability under dissipative compensation. The dissipative compensators considered are static as well as dynamic dissipative compensators. The stability proofs are based on passivity approaches, Lyapunov methods, as well as a key property of such systems, i.e., skew-symmetricity of certain matrix. The importance of the stability results obtained is that the stability is robust to parametric uncertainties and modeling errors.

For static dissipative compensators, it …

Recognition Of Quadric Surfaces From Range Data: An Analytical Approach, Ivan X. D. D'Cunha

Electrical & Computer Engineering Theses & Dissertations

In this dissertation, a new technique based on analytic geometry for the recognition and description of three-dimensional quadric surfaces from range images is presented. Beginning with the explicit representation of quadrics, a set of ten coefficients are determined for various three-dimensional surfaces. For each quadric surface, a unique set of two-dimensional curves which serve as a feature set is obtained from the various angles at which the object is intersected with a plane. Based on a discriminant method, each of the curves is classified as a parabola, circle, ellipse, hyperbola, or a line. Each quadric surface is shown to be …

Influence Of Processing Techniques On Copper Deep Levels Formation And On Photoconductivity In Silicon Doped Gallium Arsenide, Lucy M. Thomas

Electrical & Computer Engineering Theses & Dissertations

Diffusion of copper in silicon doped gallium arsenide under different diffusion conditions is studied. Copper compensated silicon doped gallium arsenide (GaAs:Si:Cu) is used as switch material for bulk optically controlled semiconductor switch, and on-state photoconductivity of the switch is primarily due to the properties of the copper deep levels introduced in the material during diffusion. Gallium arsenide being a compound semiconductor, presence of vacancies and defects make the study of diffusion a complex process. The objective of the current research is twofold: a) to study the influence of diffusion conditions and processing techniques on copper deep level formation in silicon …

Monolithic Silicon Opto-Electro-Mechanical Light Modulator, Ching-Horng Wu

Theses

A Fabry-Perot light beam modulator of the reflection-type has been designed with process and performance parameters optimized. This design takes advantage of the economies of surface micromaching using silicon substrates and selected thin films. High performance with a low drive voltage are achieved using electrostatic actuation of a thin polysilicon diaphragm. The diaphragm is a novel corrugated structure which has maximum compliance and maintains planarity during actuation. In addition, the corrugationsuspension used provides an improved linearity of amplitude modulation response as a function of the actuation voltage.

A preliminary version of this device has been fabricated through a contract foundry …

Evaluation Of Yba,Cu,O,_, Bulk Superconductors For High Field Magnet Applications, K. Y. Blohowiak, D. F. Garrigus, T. S. Luhman, K. E. Mccrary, M. Strasik, I. A. Aksay, Fatih Dogan, W. B. Hicks, J. Liu, M. Sarikaya

Materials Science and Engineering Faculty Research & Creative Works

Processing of YBCO single crystals was carried out by solidification of semi-liquid YBCO composition using a seeding technique. Microstructural characterization of the pinning centers was investigated by transmission electron microscopy. Characterization of single crystals was carried out, relating grain size and shape to the corresponding flux profiles. Current densities were calculated based on measured trapped fields. Once circulating currents were established, flux pumping and quenching experiments were conducted. These large single crystals will be incorporated into electromagnetic forming devices for use in the military and commercial aircraft manufacturing and service industries.

Evaluation Of Yba2cu3o7-X Bulk Superconductors For High Field Magnet Applications, K. Y. Blohowiak, D. F. Garrigus, T. S. Luhman, K. E. Mccrary, M. Strasik, Ilhan A. Aksay, Fatih Dogan, W. B. Hicks, J. Liu, M. Sarikaya

Materials Science and Engineering Faculty Research & Creative Works

Processing of YBCO single crystals was carried out by solidification of semi-liquid YBCO composition using a seeding technique. Microstructural characterization of the pinning centers was investigated by transmission electron microscopy. Characterization of single crystals was carried out, relating grain size and shape to the corresponding flux profiles. Current densities were calculated based on measured trapped fields. Once circulating currents were established, flux pumping and quenching experiments were conducted. These large single crystals will be incorporated into electromagnetic forming devices for use in the military and commercial aircraft manufacturing and service industries.