Engineering Commons^™

Design For Quality Manufacturability Analysis For Common Assembly Process, Suriyanarayanan Ramachandra

Theses

The globalization of market economy has precipitated a dramatic increase in competition necessitating the need for higher quality products at lower cost in shorter time periods. Shorter life cycles and proliferation of products has made companies integrate all the phases of manufacturing to bring about a superior design. Design for Quality Manufacturability (DFQM) provides a technique to invoke manufacturing and assembly considerations while designing a product. The DFQM architecture identifies factors consisting of several variables that are influenced by certain error catalysts to cause one or more specific defects. A methodology is suggested to identify and quantify these error catalysts …

Wear And Friction Of Hylamer And Polyethylene Against Cobalt Chromium A Pin-On-Disc Study, Jerry D'Alessio, Ii

Theses

Understanding friction and wear of biomaterials is essential to the success of any prosthetic joint. A pin-on-disc wear tester is used to find the friction and wear of pins of one material on a coupon of medical grade cobalt chrome. In this experiment six pins of UHMWPe (ultra high molecular weight polyethylene) and six pins of Hylamer® from Du Pont Manufacturing were tested. Four separate runs were made. The tests were performed for ten million cycles, stopping every one to one and a half million cycles for data acquisition. Volumetric wear, wear rate, and coefficients of friction were measured. Both …

An Adaptive Asynchronous Cdma Receiver And Its Convergence Analysis, Lizhi Zhong

Theses

An adaptive CDMA receiver scheme assuming perfect synchronization has been generalized in this thesis to the asynchronous channel, a much more practical assumption of the real system. Similar formulas are derived and as its synchronous version, it is still near-far resistant and requires no knowldge [sic] of received signal amplitudes and training sequences. Thus, sophisticated high-precision power control and user power estimation are not necessary and the receiver is particularly useful in mobile communications since it can adjust itself adaptively to changes in the power of the users. Tile convergence and transient behavior of the receiver are also investigated and …

Heart Rate Variability Studies On Ambulatory Subjects Using Ekg Derived Respiration, Xiaorui Tang

Theses

Power spectral analysis of heart rate variability (HRV) provides a powerful non-invasive too] for exploring the balance between sympathetic and parasympathetic components of the autonomic nervous system. In the spectrum of HRV, there are three distinct peaks. The high frequency (HF) band (0.15 to 0.4 Hz) is correlated with parasympathetic activity and this is the band of interest 'in the study.

Two OTOUPS Of SL113jeCtS were considered in this work, stroke survivors and subjects performing an oral presentation in front of an audience. Data were collected with a Holter monitor to allow for ambulatory recording. Respiration was derived from the …

Development Of A Multi-Lead Trans-Thoracic Impedance Pneumograph For Heart Rate Variability Studies, Curtis Bashford

Theses

In this study, a device that measures respiratory tidal volume and ECG for use in heart rate variability studies, was designed, built and tested. The device developed is a Multi-Lead Trans-Thoracic Impedance Pneumograph, which determines tidal volume on a breath by breath basis, utilizing both hardware and software. It uses standard ECG electrodes which provide increased comfort and inability to the subject over traditional spirometry methods. The device operates similar to traditional bipolar impedance pneumographs except that instead of only one lead (electrode pair), four leads are acquired simultaneously using time-division multiplexing; providing data from different locations and vectors on …

Time Domain And Frequency Domain Analysis Of Myoelectric Signals During Muscle Fatigue, Rakesh M. Maniar

Theses

Spectral analysis of the EMG signal is a useful tool for studying the complex phenomena of fatigue. The spectral parameters of mean frequency and median frequency, and the time domain parameter of root mean square have been used to measure localized fatigue.

The normal values of median frequency and its decline with fatigue have not as yet been determined in healthy subjects. This should be done in order to apply spectral analysis for clinical evaluations of abnormal populations. Normal median frequency values and its slope were established in this work for the upper extremity muscles of biceps, triceps and deltoid …

Wear Of Polyethylene And Hylamer On Cobalt-Chromium : A Knee Simulator Study, Alessandro F. Canonaco

Theses

Two tests were conducted to examine the wear characteristics of tibial bearings used in total knee replacement systems. Each test consisted of six A/P Glide Tibial Bearings each having a conical control arm. The plastic portion of the conical bearings were all made of UHMWPe. Each of these bearing systems was mounted onto a Co-Cr alloy tibial platform and Co-Cr alloy LCS (low contact stress) femoral component . These test samples were mounted onto the New Jersey Mark III Knee Simulator System. The simulator was configured to produce flexion and axial rotation to simulates normal gait. Each test ran at …

Performance Evaluation And Sequence Control Of An Automatedmanufacturing System, Vijaykumar D. Desai

Theses

In an automated sequential manufacturing system Programmable Logic Controllers (PLC) are widely used. As the control specification varies, the control software needs to be rewritten to accommodate the new specification. Since PLC has high flexibility, one can update the current system while it is running thereby making easier implementation. In order to design flexible, reusable and maintainable control software, a good modeling tool is required. Petri nets are such a tool. Which facilitates analysis of behavioral properties, performance evaluation, and systematic construction of discrete event simulators and controllers. In this thesis a system with one robot and five sequential work …

Area And Perimeter Measurements Of Cells With Bound Fluorescent Antibodies, Aicha Weiss

Theses

The objective of this research was to geometrically analyze the characteristics of cells, specifically area and perimeter. The images were transferred from HP A900 system to an AVS work station. The images were visualized and manipulated by the AVS which permits the distinction between the cell body, fluorescent object, and background. The intrinsic geometry of the cell was determined by using image processing algorithms written in C. The images were then passed through a threshold filter, thereby yielding a black background and a white cell body. The perimeter calculation was then applied to the black and white images. Two test …

Analysis Of Intermodulation Distortion For Mesfet Small-Signal Amplifiers, Imad Saleh Ahmad

Dissertations and Theses

Using the nonlinear Volterra series representation, analytical expressions for the third-order intermodulation distortion power and intercept point for a MESFET small-signal amplifier are derived when its equivalent circuit is bilateral and includes the gate-to-drain capacitance (C_gd) explicitly as a nonlinear element. Previously developed analytical expressions treated C_gd as a linear element or incorporated it as part of gate-to-source and drainto- source capacitances (C_gs and C_ds). These new analytical expressions are then compared with experimental data and good agreement is obtained. The analytical expressions are also used to study the variation of intermodulation distortion with …

Losslees Compression Of Rgb Color Images, Nasir D. Memon, Khalid Sayood

Department of Electrical and Computer Engineering: Faculty Publications

Although much work has been done toward developing lossless algorithms for compressing image data, most techniques reported have been for two-tone or gray-scale images. It is generally accepted that a color image can be easily encoded by using a gray-scale compression technique on each of the three accounts the substantial correlations that are present between color planes. Although several lossy compression schemes that exploit such correlations have been reported in the literature, we are not aware of any such techniques for lossless compression. Because of the difference in goals, the best way of exploiting redundancies for lossy and lossless compression …

Campus Telecommunications Systems: Managing Change, Association Of College And University Telecommunications Administrators

ACUTA: Other Publications

The purpose of this book is to provide a broadbased understanding of the rapidly changing environment of campus telecommunications. The anticipated audience for this material is the non-technical university administrator who may not have direct responsibility for telecommunications, but has a need to understand the general environment in which his telecommunications manager functions and the basic concepts of the technology. Five topic areas were selected that best cover the preponderance of issues. No attempt has been made to associate or closely coordinate materials from one chapter's subject to that of any other. Each chapter generally stands alone. In total, however, …

Wright State University College Of Engineering And Computer Science Bits And Pcs Newsletter, Volume 11, Number 1, January 1995, College Of Engineering And Computer Science, Wright State University

BITs and PCs Newsletter

A fourteen page newsletter created by the Wright State University College of Engineering and Computer Science that addresses the current affairs of the college.

Acuta Enews January 1995, Vol. 24, No. 1

ACUTA Newsletters

In This Issue

Board Report

President's message

Telecom Resources Library Update

Developing a campus telecom plan

Precautions combat

phone fraud

DC at a glance

A Staggered-Diamond Design For Automated/Manual-Hov Highway-To-Highway Interchanges And Constraints On Ahs Design For Accommodating Automated Highway Change, Jacob Tsao

Faculty Publications

This paper consists of two components. The First component addresses a key AHS infrastructure support issue—providing eight extra connector ramps, in addition to the eight existing highway-to-highway connector ramps for the conventional manual traffic, at a highway-to-highway interchange for accommodating continuous automated driving from one highway to the crossing highway. The proposed staggered-diamond design requires only four, instead of eight, separate structures and hence greatly increases the feasibility of AHS infrastructure support. However, the reduced infrastructure complexity at such interchanges could still constrain considerably the design, operation and evolution of AHS. This is the focus of the second component. The …

Stage Definition For Ahs Deployment And An Ahs Evolutionary Scenario, Jacob Tsao

Faculty Publications

Pros and cons of various mature Automated Highway Systems (AHS) have been a subject of intense study. However, such discussions are nothing but intellectual exercises unless the issue of how to evolve, in a planned and managed fashion, the current highway systems towards these mature AHS is also addressed. Since full functionality of a mature AHS cannot be realized suddenly, discrete functional steps must be identified and optimized. This paper defines an evolutionary stage towards a mature AHS as any discernible functional increment whose realization may encounter considerable difficulties requiring a significant amount of conscious effort to overcome. A good …

Multilevel Block Coded 8-Psk Modulations Using Unequal Error Protection Codes For The Rayleigh Fading Channel, Robert H. Morelos-Zaragoza, Tadeo Kamasi, Shu Lin

Faculty Publications

This paper introduces new block coded 8-PSK modulations with unequal error protection (UEP) capabilities for Rayleigh fading channels. The design of efficient block coded modulations (BCM) over 8-PSK signal sets, for the specific purpose of UEP, over Rayleigh fading channels is considered. UEP is desirable in communications systems where part of the source information is more important, or error sensitive, such as the transmission of coded speech and data broadcasting. The proposed block modulation codes are based on the multilevel construction of Imai and Hirakawa (1977). It is shown that the use of binary linear UEP (LUEP) codes as component …

In Vitro Characterization Of Transforming Growth Factor-Ss1-Loaded Composites Of Biodegradable Polymer And Mesenchymal Cells, S. B. Nicoll, A. E. Denker, R. S. Tuan

Cells and Materials

A porous, biodegradable polymer composite was fabricated from poly(L-lactic acid) (PLLA) using a solvent- casting particulate-leaching technique, and loaded with recombinant human transforming growth factor ß-1 (TGF-ß1). Tissue culture polystyrene (TCPS) and PLLA disks loaded with bovine serum albumin (BSA) served as controls. Polymer specimens were seeded at high cell density with C3H10T1/2 cells, a mouse embryonic cell line capable of differentiating into various connective tissue cell types. The polymer matrices degraded slowly in physiological saline over four weeks, with a sustained yet sporadic release of active TGF-ß1; a more controlled release of TGF-ß1 was observed in serum-containing culture medium …

Spring 1995, 90.9 Wmpg Fm

WMPG Program Guides

No abstract provided.

Fall 1995, 90.9 Wmpg Fm

WMPG Program Guides

No abstract provided.

Summer 1995, 90.9 Wmpg Fm

WMPG Program Guides

No abstract provided.

Linearly-Constrained Entropy Maximization Problem With Quadratic Costs And Its Applications To Transportation Planning Problems, Shu-Cherng Fang, Jacob Tsao

Faculty Publications

Many transportation problems can be formulated as a linearly-constrained convex programming problem whose objective function consists of entropy functions and other cost-related terms. In this paper, we propose an unconstrained convex programming dual approach to solving these problems. In particular, we focus on a class of linearly-constrained entropy maximization problem with quadratic cost, study its Lagrangian dual, and provide a globally convergent algorithm with a quadratic rate of convergence. The theory and algorithm can be readily applied to the trip distribution problem with quadratic cost and many other entropy-based formulations, including the conventional trip distribution problem with linear cost, the …

Software And Hardware Requirements For Some Applications Of Parallel Computing To Industrial Problems, Geoffrey C. Fox

Northeast Parallel Architecture Center

We discuss the hardware and software requirements that appear relevant for a set of industrial applications of parallel computing, these are divided into 33 separate categories, and come from a recent survey of industry in New York State. The software discussions includes data parallel languages, message passing, databases, and high-level integration systems. The analysis is based on a general classification of problem architectures originally developed for academic applications of parallel computing. Suitable hardware architectures are suggested for each application. The general discussion is crystalized with three case studies: computational chemistry, computational fluid dynamics, including manufacturing, and Monte Carlo Methods.

Post-Operative Carbonate-Apatite Formation In Peo/Pbt Copolymers (Polyactive®), A. M. Radder, J. E. Davies, R. N. S. Sodhi, S. A. T. Van Der Meer, J. G. C. Wolke, C. A. Van Blitterswijk

Cells and Materials

Previous studies have stressed the importance of calcification of the polyethylene oxide (PEO) I polybutylene terephthalate (PBT) copolymer surface by establishing a direct relation with the occurrence of bone-bonding. Here, we characterized the morphology as well as the composition of this post-operative reaction product in PEOIPBT copolymers. X-ray · photoelectron spectroscopical results demonstrated the ability of PEOIPBT copolymers to rapidly adsorb calcium ions from fluids. After subcutaneous implantation in rats, it was shown that polymer calcification comprised plate-shaped crystals, whereas an electron-dense layer was frequently encountered at the interface. Cells with a characteristic morphology were directly apposed to abundantly calcified …

Hip Prosthesis And Bone Mineral Absorptiometry: Effect Of Short-Term Administration Of Calcitriol, Mario Caniggia, Bruno Frediani, Leonardo Osti

Cells and Materials

In this double blind study, seven out of fourteen patients who had received a cementless hydroxyapatitecovered hip prosthesis were given calcitriol (1 p.g daily), and seven an inert placebo for a period of four months. At the end of this period, total body bone densitometry (TBBD) and absorptiometric measurements in the regions of interest (ROIs) close to the prosthesis and in the opposite femur revealed that the TBBD values had decreased in the patients receiving placebo and increased in those receiving calcitriol. Furthermore, bone mineral density in the ROis had increased on the non-operated side of the calcitriol-treated patients (although …

Backscattered Electron Imaging To Enhance Microstructural Contrast In Poly(Methyl Methacrylate) Bone Cement Fracture Analysis, L. D. T. Topoleski, P. Rutledge, X. Lu

Cells and Materials

Poly(methyl methacrylate) (PMMA) bone cement is used as a grout to secure joint replacement prostheses into bone. It has a distinct microstructure made up of: prepolymerized beads, an interbead matrix polymer, a radiopacifier {barium sulphate (BaS04) or zirconium dioxide (Zr02)}, and pores or voids; the radiopacifier is found only in the interbead matrix of the cured bone cement. The mechanism of slow or fatigue crack growth appears to be initial micro-cracking through the interbead matrix, followed by coalescence of the microcracks to form a continuous crack. Thus, distinguishing the interbead matrix from the pre-polymerized beads is important for investigating fatigue …

Biodegradation Of Synthetic Biphasic Calcium Phosphate And Biological Calcified Substratum By Cells Of Hemopoietic Origin, A. Soueidan, O. I. Gan, J. M. Bouler, F. Gouin, G. Daculsi

Cells and Materials

Different types of osteoclastic cells (authentic osteoclasit from human giant cell tumor and bone marrow of newborn rats; newly-formed osteoclasts from adult rat bone marrow), giant multinucleated cells and macrophages were studied for their effect on synthetic and natural mineralized substrata. Biphasic calcium phosphate ceramic consisted of hydroxyapatite and beta tricalcium phosphate was chosen for in vitro experiments, and dentine served as a positive control for cell resorbing activity . Our results show the limited capacity of authentic and newly-formed osteoclasts to resorb synthetic ceramic as compared to that of natural substrata. In vitro cell-mediated biodegradation included also modifications of …

Resorption Of Natural Calcium Carbonate By Avian Osteoclasts In Vitro, G. Guillemin, S. J. Hunter, C. V. Gay

Cells and Materials

Osteoclasts isolated from the endosteum of 2.5 to 3-week chick tibia were cultured on glass coverslips or natural CaC03 (Tridacna) wafers for 2 and 4 days. The cells were exposed to the pH-dependent dye, acridine orange, and fluorescence was measured by a light microscope photometer. Fluorescence intensity values were higher in cells adherent to Tridacna wafers than in those incubated on glass after 2 and 4 days of culture (three and two-fold, respectively). Moreover, osteoclasts on Tridacna wafers were more flattened and were found to produce resorption pits. Acid production by osteoclasts cultured on Tridacna wafers was stimulated …

Cell Adhesion To Crystal Surfaces: A Model For Initial Stages In The Attachment Of Cells To Solid Substrates, D. Hanein, B. Geiger, L. Addadi

Cells and Materials

This study addresses the mechanism of the chirally-restricted, ROD-independent adhesion of A6 epithelial cells to the {011} faces of calcium {R,R)-tartrate tetrahydrate crystals. The extensive and rapid adhesion of the cells to these surfaces, in the presence or absence of serum proteins, is distinctly different from the extracellular matrix-mediated adhesion to conventional tissue culture surfaces or to the {101} faces of the same crystals. The differences are manifested by insensitivity to ATP depletion, to disruption of microfilaments and microtubules and even to formaldehyde fixation of the cells. Furthermore, trypsin pretreatment does not affect cell attachment to the {011} faces, nor …

Ultrasonic Detection Of A Plastic Hinge In Bolted Timber Connections, David Pollock, Donald A. Bender, Don E. Bray, James T P Yao

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

Connections between structural members are critical elements that typically govern the performance of structural systems; hence, techniques for monitoring the condition of connections are needed to provide early warning of structural damage. Plastic hinge formation in fasteners frequently occurs in timber connections when the yield capacity is exceeded. An innovative pulse echo testing technique was developed for detecting the formation of a plastic hinge in bolted timber connections and estimating the associated magnitude of connection displacement. A shift in overall signal centroid proved to be the best flTedictor of plastic hinge formation, with a coefficient of determination (R2) of 0.9. …