Engineering Commons^™

Development Of Nial-Based Intermetallic Alloys: Effect Of Chromium Addition, R. Tiwari, Surendra N. Tewari, R. Asthana, A. Garg

Chemical & Biomedical Engineering Faculty Publications

The mechanical behavior of dual-phase NiAl(Cr) microstructures, consisting of elongated primary NiAl grains aligned with an intergranular NiAl-Cr eutectic phase, produced by extrusion of a cast NiAl(Cr) alloy, has been examined. Chromium addition to create a dual phase NiAl-based aligned microstructure leads to large increases in the yield strength but no significant toughness improvement. This is achieved primarily by solid solution hardening and precipitation hardening. The constitutional hardening rate resulting from deviations from stoichiometry in the nickel-rich NiAl was estimated to be about 66 MPa per atomic per cent of nickel.

Inp Optical Constants Between 0.75 And 5.0 Ev Determined By Variable-Angle Spectroscopic Ellipsometry, C. M. Herzinger, Paul G. Snyder, B. Johs, John A. Woollam

Department of Electrical and Computer Engineering: Faculty Publications

Using variable-angle spectroscopic ellipsometry (VASE) InP optical constants for photon energies have been determined in the range from 0.75 to 5.0 eV, which includes the fundamental gap at 1.35 eV. Above 1.5 eV the results are consistent with previously measured pseudovalues from an oxide-stripped sample when a very thin residual over-layer is accounted for. They are also shown to be compatible with previously published prism measurements of refractive index below the band gap. Real and imaginary parts of the dielectric function are shown to be Kramers-Kronig (KK) self-consistent above the gap, and the KK analysis was used to extend the …

Tree Restructuring Approach To Mapping Problem In Cellular Architecture Fpgas, Narahari Ramineni

Dissertations and Theses

This thesis presents a new technique for mapping combinational circuits to Fine-Grain Cellular-Architecture FPGAs. We represent the netlist as the binary tree with decision variables associated with each node of the tree. The functionality of the tree nodes is chosen based on the target FPGA architecture. The proposed tree restructuring algorithms preserve local connectivity and allow direct mapping of the trees to the cellular array, thus eliminating the traditional routing phase. Also, predictability of the signal delays is a very important advantage of the developed approach. The developed bus-assignment algorithm efficiently utilizes the medium distance routing resources (buses). The method …

Design Of A Digital Compensation Filter, Nader Fakhry

Dissertations and Theses

The 24-bit Motorola DSP56001 processor will be used in combination with the DSP56ADC16 and the PCM-56 to design a good FIR compensation filter. Our objective is to digitize the input analog signal, and to compensate for the attenuation in the magnitude response of the digital sine wave. Two different experiments will be conducted, a hands on approach, and a simulation program. The first one will be realized directly, using the DSP system. We will determine the magnitude response of the system, and then deduce the coefficients of the FIR sin(x)/x filter. A look up table will store those values which …

Ccfss Technical Bulletin February 1995, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Technical Bulletins (1993 - 2020)

No abstract provided.

Wright State University College Of Engineering And Computer Science Bits And Pcs Newsletter, Volume 11, Number 2, February 1995, College Of Engineering And Computer Science, Wright State University

BITs and PCs Newsletter

An eighteen page newsletter created by the Wright State University College of Engineering and Computer Science that addresses the current affairs of the college.

Acuta Enews February 1995, Vol. 24, No. 2

ACUTA Newsletters

In This Issue

Board Report

President's message

ACUTA hires Computer Services Administrator

Peer presentations at Maui

DC at a glance

From ACUTA Headquarters

Optimization Of Expanded Polypropylene Foam Coring To Improve Bumper Foam Core Energy Absorbing Capability, Gregory Frederick, Gregory A. Kaepp, Conrad M. Kudelko, Peter J. Schuster, Friedrich Domas, Udo G. Haardt, Werner Lenz

Mechanical Engineering

To design a cost, weight, and energy efficient bumper foam energy absorber, it is important to consider optimizing the shape of coring employed in the design of the system. In this paper, a number of foam coring patterns are studied by both empirical and analytical methods. The size and shape of proposed core designs are studied in detail with consideration given to several different densities of expanded polypropylene (EPP) foam. Using the finite element method of structural analysis, it is possible to have an inside look at the stress distribution during deformation of foam structures. An optimization study using the …

Influence Of Interfacial Reactions On The Fiber-Matrix Interfacial Shear-Strength In Sapphire Fiber-Reinforced Nial(Yb) Composites, Surendra N. Tewari, R. Asthana, R. Tiwari, R. R. Bowman, J. Smith

Chemical & Biomedical Engineering Faculty Publications

The influence of microstructure of the fiber-matrix interface on the interfacial shear strength, measured using a fiber-pushout technique, has been examined in a sapphire-fiber-reinforced NiAl(Yb) matrix composite under the following conditions: (1) as-fabricated powder metallurgy (PM) composites, (2) PM composites after solid-state heat treatment (HT), and (3) PM composites after directional solidification (DS). The fiber-pushout stress-displacement behavior consisted of an initial ''pseudoelastic'' region, wherein the stress increased linearly with displacement, followed by an ''inelastic'' region, where the slope of the stress-displacement plot decreased until a maximum stress was reached, and the subsequent gradual stress decreased to a ''frictional'' stress. Energy-dispersive …

Otter: A Testbed Submersible For Robotics Research, Tim Mclain, H H. Wang, R L. Marks, S D. Fleischer, D W. Miles, G A. Sapilewski, S M. Rock, M J. Lee, R C. Burton

Faculty Publications

Untethered, unmanned submersibles (UUSs) have the potential of becoming useful tools in nuclear reactor inspection and repair and waste-site cleanup and survey, in addition to subsea exploration. Classical "hand-in-glove" control methods used currently by tethered, remotely-operated vehicles (ROVs) are unsuitable for UUS systems which have, at best, limited communications. The Stanford Aerospace Robotics Laboratory (ARL) has joined with the Monterey Bay Aquarium Research Institute (MBARI) in a program to develop new methods of controlling UUS systems.

As a part of this effort, a submersible testbed has been built to test and develop new technologies that will make UUSs useful tools …

Ccfss News February 1995, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Newsletters (1999 - 2008)

No abstract provided.

Reproducible Technique For Packing Laboratory-Scale Trickle-Bed Reactors With A Mixture Of Catalyst And Fines, Muthanna H. Al-Dahhan, Yuanxin Wu, Milorad P. Duduković

Chemical and Biochemical Engineering Faculty Research & Creative Works

A Reproducible Procedure for Packing Small-Diameter Packed Beds with a Mixture of Fines and Catalyst is Reported. Such Beds Are Essential for Process Catalyst Testing in Trickle-Flow Reactors. Packing Uniformity Along the Bed, Reproducibility of Single-Phase Pressure Drop and Reproducibility of Liquid Holdup and Two-Phase Flow Pressure Drop in Repacked Beds Has Been Demonstrated. © 1995, American Chemical Society. All Rights Reserved.

A Summary Of Highway Revenues, Expenses, And Distributions: 1987 Through 1994, Herpicc

Indiana Local Technical Assistance Program (LTAP) Publications

This report shows the history of receipts, expenses and distributions of revenues that provide funding to all local governments for highway, road and street work.

Sensitization To Self (Virus) Antigen By In Situ Expression Of Murine Interferon-Gamma., Myung-Shik Lee, Matthias Von Herrath, Hans Reiser, Michael B.A. Oldstone, Nora Sarvetnick

Journal Articles: Regenerative Medicine

Autoimmune disease results from inflammatory destruction of tissues by aberrant self-reactive lymphocytes. We studied the autoimmune potential of T lymphocytes immunologically ignorant of viral antigens acting as self antigens and whether the host defense molecule IFN-gamma could stimulate these cells to cytotoxic competency. For this purpose, we produced double transgenic mice expressing pancreatic IFN-gamma as well as lymphocytic choriomeningitis virus (LCMV) nucleoprotein (NP) or glycoprotein (GP) antigen. 100% of the NP+/IFN-gamma+ mice became diabetic before 2 mo of age, while none of the NP single transgenic littermates and only 10% of IFN-gamma single transgenic littermates did. Strikingly, NP+/IFN-gamma+ mice spontaneously …

Myasthenia Gravis-Like Syndrome Induced By Expression Of Interferon Gamma In The Neuromuscular Junction., Danling Gu, Lise Wogensen, Nigel A. Calcutt, Chunyao Xia, Simin Zhu, John P. Merlie, Howard S. Fox, Jon Lindstrom, Henry C. Powell, Nora Sarvetnick

Journal Articles: Regenerative Medicine

Abnormal humoral responses toward motor end plate constituents in muscle induce myasthenia gravis (MG). To study the etiology of this disease, and whether it could be induced by host defense molecules, we examined the consequences of interferon (IFN) gamma production within the neuromuscular junction of transgenic mice. The transgenic mice exhibited gradually increasing muscular weakness, flaccid paralysis, and functional disruption of the neuromuscular junction that was reversed after administration of an inhibitor of acetylcholinesterase, features which are strikingly similar to human MG. Furthermore, histological examination revealed infiltration of mononuclear cells and autoantibody deposition at motor end plates. Immunoprecipitation analysis indicated …

Alternatives To The Current Aashto Standard Bridge Sections, Joseffa Viktoria Meir, Michael Ramon Cicciarelli, J. A. Ramirez, Robert H. Lee

JTRP Technical Reports

The main objective of this study was evaluate feasible alternatives to the current AASHTO bridge girders used in Indiana. This evaluation included precast pretensioned bridge girders for spans from 30 to 130 feet with girder spacing between 5 and 10 feet up to 12 feet for the longer spans. Other criteria included girder design concrete compressive strengths up to 7000 psi, 8” total concrete deck thickness with design strength of 4000 psi, grade 60 steel for slab reinforcement and stirrups and ½” special grade 270 low-relaxation strand for prestressing steel. Post-tensioning and pretensioned box girders were outside the scope of …

Dirac's Equation In Semiclassical Physics, Lee W. Casperson

Electrical and Computer Engineering Faculty Publications and Presentations

Dirac's equation provides the most rigorous basis known for many calculations in relativistic quantum mechanics. A set of dynamical equations having greater intuitive content can be derived from Dirac's equation without any approximations. These secondary equations govern the properties of a Dirac particle as functions of time and space and are similar to the corresponding equations governing a classical charged fluid. Several new density functions are implied by these equations and are appropriate for incorporation into the various semiclassical models of physics.

Bs News

Building Services Engineering

No abstract provided.

Metal Stud Manufacturer's Association Catalog, Metal Stud Manufacturer's Association

CCFSS Library (1939 - present)

No abstract provided.

Experimental And Numerical Determination Of Fluid Velocity Profiles And Turbulence Intensity In Mixing Vessels, Chun-Chiao Chou

Dissertations

In this study, both a laser-Doppler velocimeter (LDV) and a computational fluid dynamic (CFD) software package (FL UENI) were used to experimentally determine and numerically predict the velocity distribution of an unbaffled and a baffled mixing vessel. Two types of impellers were employed, namely a flat blade turbine (FBT) and a pitched blade turbine (PBT). These impellers were studied in a single-impeller or multiple-impeller configuration in the unbaffled and baffled vessels. The flow characteristics in the impeller regions were measured by LDV and used as boundary conditions in the numerical computation. Turbulence effects were numerically simulated using either the k-c …

A Petri-Net Based Methodology For Modeling, Simulation, And Control Of Flexible Manufacturing Systems, Venkatesh Kurapati

Dissertations

Global competition has made it necessary for manufacturers to introduce such advanced technologies as flexible and agile manufacturing, intelligent automation, and computer-integrated manufacturing. However, the application extent of these technologies varies from industry to industry and has met various degrees of success. One critical barrier leading to successful implementation of advanced manufacturing systems is the ever-increasing complexity in their modeling, analysis, simulation, and control. The purpose of this work is to introduce a set of Petri net-based tools and methods to address a variety of problems associated with the design and implementation of flexible manufacturing systems (FMSs). More specifically, this …

Theory, Design And Applications Of Linear Transforms For Information Transmission, Adil Benyassine

Dissertations

The aim of this dissertation is to study the common features of block transforms, subband filter banks, and wavelets, and demonstrate how discrete uncertainty can be applied to evaluate these different decomposition techniques. In particular, we derive an uncertainty bound for discrete-time functions. It is shown that this bound is the same as that for continuous-time functions, if the discrete-time functions have a certain degree of regularity.

This dissertation also deals with spectral modeling in filter banks. It is shown, both theoretically and experimentally, that subspectral modeling is superior to full spectrum modeling if performed before the rate change. The …

Robust Approach To Object Recognition Through Fuzzy Clustering And Hough Transform Based Methods, Tianxiong Fu

Dissertations

Object detection from two dimensional intensity images as well as three dimensional range images is considered. The emphasis is on the robust detection of shapes such as cylinders, spheres, cones, and planar surfaces, typically found in mechanical and manufacturing engineering applications. Based on the analyses of different HT methods, a novel method, called the Fast Randomized Hough Transform (FRHT) is proposed. The key idea of FRHT is to divide the original image into multiple regions and apply random sampling method to map data points in the image space into the parameter space or feature space, then obtain the parameters of …

Design And Micro-Fabrication Of Tantalum Silicide Cantilever Beam Threshold Accelerometer, Chang Joo Kim

Dissertations

Microfabricated threshold accelerometers were successfully designed and fabricated following a careful analysis of the electrical, mechanical, and fabrication issues inherent to micron-sized accelerometers. A uniform cantilever beam was chosen because of the simplicity of design and fabrication. New models for the electrostatic force exerted on the cantilever beam were developed and calculations were made that accurately predicted the electrical characteristics of the accelerometer. The calculations also provided design guidelines for optimizing the accelerometer dimensions. Computer simulation demonstrated that the error of the electrostatic force, calculated using the most accurate model, was within 2% of the actual force which was obtained …

Combustion Of Methyl Chloride, Monomethyl Amine, And Their Mixtures In A Two Stage Turbulent Flow Reactor, Fuhe Mao

Dissertations

The feasibility of converting fuel-bound chlorine and nitrogen into HCl and N₂ with reduced pollutant emissions of CO, NO, and unburned hydrocarbons was investigated in a two-stage turbulent flow reactor. The study consists of four segments: completion and validation of the experimental facility, experimental and modeling studies of methyl chloride (CH₃Cl) combustion, similar studies on monomethyl amine (CH₃NH₂), and finally studies on simultaneous CH₃Cl and CH₃NH₂ combustion.

Validation of the experimental facility was made by combustion of ethylene (C₂H₄) and air under both fuel-lean …

Electrical Characteristics Of Novel Heterojunction Diodes Of Thin Relaxation Semiconductors/P-Si/, Hyung Joo Lee

Dissertations

The relaxation semiconductor is defined as one in which the dielectric relaxation time (τd;resistivity times permittivity) is greater than lifetime (τo). Non-hydrogenated amorphous Silicon Carbide (SiC) and KrF excimer laser induced disordered Si were used for the relaxation semiconductors. Both semiconductors have high resistivity, wide energy gap, and numerous defects. A novel diode, consisting of those semiconductors on p-type crystalline Silicon (c-Si), was fabricated. In the diode structure, an injecting contact was made on the relaxation material and a Schottky barrier contact was made on the c-Si.

Electrical characteristics of both diodes were found to have interesting …

Analysis Of Plates And Reinforced Concrete Columns By Cubic B-Spline Function, Gang Wang

Dissertations

Applying spline functions to numerical structural analysis has been more common in recent years. The recent increase use of spline functions is mainly due to their excellent characteristics, such as sectionalized continuity, linear combination, flexibility, and easy use for various boundary conditions. The whole deformed shape of some structures or substructures can be described with one displacement function constructed by a series of spline functions. By doing this, the mesh generation and the huge computer memory space are no longer needed because only one single superelement can be used in the whole process. The choice of spline functions as displacement …

On Adaptive Code Division Multiple Access Detectors, Wenping Chen

Dissertations

Several variations of adaptive CDMA synchronous receiver schemes which can automatically adjust to the system parameters, are studied in this dissertation. Unlike their non-adaptive counterparts, these adaptive detectors require no knowledge of the received signals' energies and have similar or better performance.

Minimum energy and decorrelating criterion are used to update the weights. Since weights are updated according to the changes of the detector's outputs, hence no training sequence is required. The convergences of some of the aforementioned adaptive detectors are also disscussed.

The detectors proposed in this dissertation are near-far resistant,thus rendering the high-precision power control unnecessary. Among them, …

Low Pressure Chemical Vapor Deposition Of Silicon Nitride Films From Tridimethylaminosilane, Xin Lin

Theses

In this study amorphous stoichiometric silicon nitride films were synthesized by low pressure chemical vapor deposition (LPCVD) using tri(dimethylamino) silane (TDMAS) and ammonia (NH₃). The growth kinetics were determined as a function of temperature in the range of 650 - 900 °C, total pressure in the range of 0.15 - 0.60 Torr, and NH₃/TDMAS flow ratio in the range of 0 - 10. At constant condition of pressure (0.5 Torr), TDMSA flow rate (10 sccm) and NH₃ flow rate (100 sccm), the deposition rate of as-deposited silicon nitride films was found to follow an Arrehnius …

Am/Fm Digital Audio Broadcasting In-Band On-Channel Transmission, Michael Meyer

Theses

This thesis examines the in-band on-channel transmission of digital audio data for application in Digital Audio Broadcasting (DAB). The premise is to use the existing FM channels for transmission of DAB. For the FM channel used for analog audio transmission, two different scenarios are suggested and investigated.

In the first scenario, to enable overlay of the new DAB and current FM transmissions, the digital data is modulated by a direct sequence spread spectrum signal to bring the average transmitted power below that of the FM signal using the same channel. The FM signal interferes with the digital transmission and it …