Engineering Commons^™

A Maximum Torque Per Ampere Control Strategy For Induction Motor Drives, O. Wasynczuk, Keith Corzine, S. D. Sudhoff, Jerry L. Tichenor, P. C. Krause, I. G. Hansen, L. M. Taylor

Electrical and Computer Engineering Faculty Research & Creative Works

In this paper, a new control strategy is proposed which is simple in structure and has the straightforward goal of minimizing the stator current amplitude for a given load torque. It is shown that the resulting induction motor efficiency is reasonably close to optimal and that the approach is insensitive to variations in rotor resistance. Although the torque response is not as fast as in field-oriented (FO) control strategies, the response is reasonably fast. In fact, if the mechanical time constant is large relative to the rotor time constant, which is frequently the case, the sacrifice in dynamic performance is …

Designing Power Bus Decoupling For Cmos Devices, S. Radu, Richard E. Dubroff, Todd H. Hubing, Thomas Van Doren

Electrical and Computer Engineering Faculty Research & Creative Works

The adequacy of the DC power bus decoupling for CMOS devices can be determined if the effective board decoupling capacitance, the CMOS load capacitance, the CMOS power dissipation capacitance, the switching time, and the allowable bus noise voltage are known. A simple method is presented for estimating the effective decoupling capacitance. The load and power dissipation capacitance values are shown analytically and experimentally to be closely related to the transient current. The transient current and switching time are used to estimate the transient noise voltage on the power bus

Excitation Of The Whispering-Gallery-Modes At The Shielded Hemispherical Dielectric Resonator, Sergey Kharkovsky, V. V. Kutuzov, A. E. Kogut, V. A. Solodovnik

Electrical and Computer Engineering Faculty Research & Creative Works

No abstract provided.

Millimeter Wave Signals Detection By Means Of Monocrystal Hexagonal Ferrite Ellipsoid, Marina Koledintseva, Alexander A. Kitaytsev

Electrical and Computer Engineering Faculty Research & Creative Works

Stable nonlinear resonance effects (SNLREs) have been already studied in crystallographically "isotropic" ferrogarnet ferrite resonators (FR), employed as microwave detectors in the frequency range of 300 MHz to 30 GHz. Application of prospective hexagonal monocrystal ferrites with large field of crystallographic magnetic anisotropy leads to the possibility of a gyromagnetic converter (GC) design for mm waveband (from 30 to 200 GHz) without massive external magnets. This paper deals with the analysis of a more general case with taking into account both crystallographic and form anisotropy as well as the arbitrary orientation of the main crystallographic axis with respect to the …

A Practical Continually Online Trained Artificial Neural Network Controller For A Turbogenerator, Ganesh K. Venayagamoorthy, Ronald G. Harley

Electrical and Computer Engineering Faculty Research & Creative Works

This paper reports on the simulation and practical studies carried out on a single turbogenerator connected to an infinite bus through a short transmission line, with a continually online trained (COT) artificial neural network (ANN) controller to identify the turbogenerator, and another COT ANN to control the turbogenerator. This identifier/controller augments/replaces the automatic voltage regulator and the turbine governor. Results are presented to show that this COT ANN identifier/controller has the potential to allow turbogenerators to operate more closely to their steady-state stability limits and nevertheless “ride through” severe transient disturbances such as three phase faults. This allows greater usage …

An Efficient, Fast Converging Adaptive Filter For Network Echo Cancellation, Steven L. Grant

Electrical and Computer Engineering Faculty Research & Creative Works

This paper discusses a fast efficient adaptive filtering algorithm for network echo cancellers PNLMS++ (proportionate normalized least mean squares ++). Compared to the conventional normalized least mean squares (NLMS) algorithm, PNLMSI++ converges much more quickly when the echo path is sparse. When the echo path is dispersive, the convergence rate is the same as NLMS. In addition, the new algorithm diverges at the same rate and to the same misalignment level as NLMS during periods of undetected double-talk. PNLMS++ is only 50% more computationally complex than NLMS and requires no additional memory

Cell Mapping Based Fuzzy Control Of Car Parking, Tea-Quin Kim, Ming-Chuan Leu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper describes the development of a near-optimal fuzzy controller for maneuvering a car in a parking lot. To generate the rules of the fuzzy controller, a cell mapping method is utilized to systematically generate near-optimal trajectories for all possible initial states in the parking lot. Based on the input-output relations of these trajectories, which represent the states and controls of the corresponding cells, a set of fuzzy rules are generated automatically. In order to result in a small number of fuzzy rules from the large amount of numerical information generated by cell mapping, grouping of trajectories is proposed and …

Metal-Organic Chemical Vapor Deposition Of Sr-Co-Fe-O Films On Porous Substrates, C.-F. Xia, P. Atanasova, Robert W. Schwartz, T. L. Ward

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Aerosol-assisted chemical vapor deposition using the b-diketonate precursors Sr(tmhd)2•2H2O, Fe(tmhd)3 and Co(tmhd)3 was investigated for depositing thin films of the mixed-conducting ceramic SrCoyFe1-yO3-d onto porous a-Al2O3 substrates. Single-phase SrCoyFe1-yO3-d perovskite films were obtained at a deposition temperature of 550°C and pressure of 15 mm Hg, whereas deposition at atmospheric pressure produced mixed-phase films. The Co/Fe elemental ratios in the films reflected those in the precursor solution, but the films were depleted in Sr. Reduced-pressure deposition provided a more uniform film morphology than atmospheric-pressure, and led to a supported film which was leak-tight to N2 flow.

Belted Work Machine, J. J. Burckhartzmeyer, E. R. Crabb, T. F. Lehnhoff, A. L. Watson Jr.

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A heavy duty belt laying work machine includes a frame, a driver wheel mounted in supporting relation to the frame on each lateral side thereof, an idler wheel assembly disposed on each lateral side of the frame. The idler wheel assembly includes an idler wheel and a carry-roller, each of which is rotatably connected to an idler support arm that is pivotally mounted in supporting relation to the frame. A mid-roller is disposed on each lateral side of the frame between the driver wheel and the idler wheel assembly and rotatably connected to a mid-roller support arm mounted in supporting …

A Novel Thin Film Transistor Using Double Amorphous Silicon Active Layer, Jong Hyuni Choi, Chang-Soo Kim, Byung Cheon Lim, Jin Jang

Electrical and Computer Engineering Faculty Research & Creative Works

We have fabricated a novel low off-state leakage current thin-film transistor (TFT) using a chlorine incorporated amorphous silicon [a-Si:H(:Cl)] and amorphous silicon (a-Si:H) stacked active layer, in which conduction channel is formed in a-Si:H and a-Si:H(:Cl) is photo-insensitive material. The off-state photo-leakage current of the a-Si:H(:Cl)/a-Si:H TFT is much lower than that a conventional a-Si:H TFT.

An Analog Vlsi Circuit Implementing An Orthogonal Continuous Wavelet Transform, Dongwei Chen, John G. Harris

Electrical and Computer Engineering Faculty Research & Creative Works

We have developed the theory and analog hardware implementation for a Continuous Wavelet Transform (CWT). This novel circuit performs an orthogonal decomposition of temporal signals, such as speech, in a frequency range of 10 Hz to 20 kHz. This multiresolution processor expands the Laguerre structure originally developed by Lee (1960).

An Improved Method For Incorporating Magnetic Saturation In The Q-D Synchronous Machine Model, Keith Corzine, Brian T. Kuhn, S. D. Sudhoff, H. J. Hegner

Electrical and Computer Engineering Faculty Research & Creative Works

An improved technique for incorporating saturation into the q-d axis model (Park''s model) of a synchronous machine is proposed. By choosing magnetizing flux linkage as a state variable, iterative procedures required by traditional methods are avoided. The saturation function is represented by an arctangent function which has some distinct advantages over polynomial representations and look-up tables. In particular, the parameters of the proposed function all have physical significance and the proposed function is defined over an infinite range of flux linkage. The model is verified for steady-state and transient conditions using a laboratory synchronous machine-rectifier system similar to those commonly …

Dc Link Stabilized Field Oriented Control Of Electric Propulsion Systems, Keith Corzine, S. D. Sudhoff, Steven F. Glover, H. J. Hegner, H. N. Robey

Electrical and Computer Engineering Faculty Research & Creative Works

Induction motor based electric propulsion systems can be used in a wide variety of applications including locomotives, hybrid electric vehicles, and ships. Field oriented control of these drives is attractive since it allows the torque to be tightly and nearly instantaneously controlled. However, such systems can be prone to negative impedance instability of the DC link. This paper examines this type of instability and sets forth a readily implemented albeit nonlinear control strategy to mitigate this potential problem.

Object-Oriented Computer Simulations Of Physical Systems Using Dual Reciprocity Boundary Element Methodology, J. Friedrich

Turkish Journal of Electrical Engineering and Computer Sciences

Models of physical systems are essential in every engineering field. This work deals with computer simulations of physical systems that can be mathematically modelled by differential equations together with sufficient boundary conditions. The computer simulations are based on object-oriented technology and the dual reciprocity boundary element method which is a universal solution scheme for various types of partial differential equations (e.g. Laplace, Poisson, diffusion, convection-diffusion, and steady Navier-Stokes equation). This technique fulfills efficiency criteria like precision, robustness, versatility, programmability, user-friendliness, need of computational time and computer memory to a very high degree. This is demonstrated by three examples: Laplace's solution …

Distribution System Planning Usign Mixed Integer Programming, Belgin Türkay

Turkish Journal of Electrical Engineering and Computer Sciences

This paper presents an improved mathematical model to optimise the size and locations of substations and the network routing problem. The model was formulated to minimise the total cost of the network by determining the optima of the substation locations and power, the load transfers between the demand centers, the feeder routes and the load flow in the network subject to a set of constraints. The computational results of a devised sample problem indicate that the developed optimisation model and its code are adequate for computer aided planning of distribution systems.

Analysis Of Nonlinear Sustained Oscillations In Discrete Systems With Backlash And Resolution By Using A Discretization-Oriented Describing Function, M. De La Sen, A. Pena, J. Esnaola

Turkish Journal of Electrical Engineering and Computer Sciences

In this paper, a discretization-oriented describing function is derived for nonlinear devices combining backlash and quantization (resolution) while being subject to discretization through a sampler and zero-order hold. Such a describing function is frequency-dependent so that the overall nonlinearity, which includes both resolution and backlash, is interpreted as possessing nonlinear inertia. That nonlinear inertia is generated by the sampling process, since it does not appear if the system is continuous. The presence of nonlinear sustained oscillations (limit cycles) is investigated through simulations.

Signal Injection With Perceptual Criteria, T. Engi̇n Tuncer

Turkish Journal of Electrical Engineering and Computer Sciences

In this paper, a novel method for increasing the coding performance and information transmission capacity is presented. This method is mainly based on perceptual modelling of input signal such as speech or audio. Presented approach may be seen as an alternative to transforms which dynamically change analysis window for better energy compaction. A perceptual model is established in order to obtain a global masking threshold in frequency below which sounds become inaudible. Certain criteria are developed for identifying the signal injection bands. A new multiband filter design method which is a generalization of windowing method is used to separate the …

State Of Art In Realistic Head Modeling For Electro-Magnetic Source Imaging Of The Human Brain, Nevzat G. Gençer, İ. Oğuz Tanzer, M. Kemal Özdemi̇r, Can E. Acar, Mert Sungur

Turkish Journal of Electrical Engineering and Computer Sciences

Electric currents produced by the neural activity in the brain create electric potentials on the scalp and magnetic field distribution outside the scalp. Measuring electric and magnetic fields provides a means to understand the spatio-temporal distribution of the neural activity. The representations of the intracellular electric current of active cell populations based on bimodal data are called electro-magnetic source image (EMSI). With the recent development of large arrays of magnetic sensors, and systems for measuring scalp voltages at more than 100 locations, it is now feasible to implement computational methods that employ numerical models which incorporate the correct geometry and …

A Comparison Of Some Low Cost Laminates For Antennas Operating In The 2.45 Ghz Ism Band, Max Ammann

Conference papers

An evaluation of some low-cost laminates suitable for microstrip patch antennas is presented. Criteria for the selection of substrates for antenna fabrication are given careful consideration. A coaxial-probe fed linearly-polarized rectangular microstrip patch operating at a frequency of 2.45 GHz was fabricated on four different low cost laminates. The substrates used were polyester, epoxy glass (FR-4), a ceramic filled PTFE composite and a woven glass-reinforced hydrocarbon and ceramic thermoset material. Material properties are discussed and the antenna performances are evaluated and compared to one fabricated on a thick glass-loaded microfiber PTFE substrate. An evaluation of some inexpensive microstrip antenna CAD …

An Alternative Method For Determining Adjusted Function Points As The Basis For Software Cost Estimating, William Alexander Eldred

Engineering Management & Systems Engineering Theses & Dissertations

As software costs become an increasingly higher percentage of total computer system costs, it becomes increasingly more important for software development managers to have the ability to predict development costs with reasonable accuracy early in the software development cycle. Software development cost estimates are based in large measure on software size. Function points are considered by many to be a de facto industry standard as a size metric. The function points technique, unlike lines-of-code, can be applied early in the software development cycle and is language independent. Critics claim that the function point “value adjustment factor,” which purports to capture …

Passive Circuit Modeling Using Ipa510, Hassan Hiwaidi Al-Sheikhly

Dissertations and Theses

Characterizing the high speed interconnect performance of circuit board, integrated circuit packages and multichip module become very important when the clock frequencies in digital and RF systems become larger than 200 MHz. At time scales less than 2 ns distributed approach must be used to measure package parasitics (stray inductance and capacitance) and transmission line effects.

A practical way to measure and model the package parasitics is by utilizing Interconnect Parameter Analyzer (IP A510). The IP A510 uses Time Domain Reflectometry (TDR) technique. The TDR technique is based on sending a waveform to a device under test (DUT) and capturing …

The Design Of Cube Calculus Machine Using Sram-Based Fpga Reconfigurable Hardware Dec’S Perle-1 Board, Qihong Chen

Dissertations and Theses

Presented in this thesis are new approaches to column compatibility checking and column-based input/output encoding for Curtis decompositions of switching functions. These approaches can be used in Curtis-type functional decomposition programs for applications in several scientific disciplines. Examples of applications are: minimization of combinational and sequential logic) mapping of logic functions to programmable logic devices such as CPLDs, MPGAs, and FPGAs, data encryption, data compression, pattern recognition) and image refinement. Presently, Curtis-type functional decomposition programs are used primarily for experimental purposes due to performance, quality, and compatibility issues. However) in the past few years a renewal of interest in the …

Communicating Conceptual Design Of Mechatronic Systems, Muir Lee Harding

Dissertations and Theses

Today's engineering designers must adapt to a changing model of product development. In the past, a single engineer could design, develop and deploy competitive systems --this is often no longer the case. Designing a mechanical system with integrated microprocessor control requires the collaboration of a cross-disciplinary team of engineers and, in many cases, no single member of the team understands the workings of the entire system. Consequently, as systems become increasingly complex, the ability to collaborate and reliably communicate design information becomes more and more crucial. Effective communication 1s particularly critical in conceptual design, where a poor decision has the …

Rtl Power Estimation Of Sequential Circuits, Sridhar Muthrasanallur

Dissertations and Theses

Power consumption has become a major concern in the electronic industry in recent years because of the increased demand for portable electronic devices. Part of the problem in power conscious design is accurate power estimation. Power estimation at low-levels of design abstraction is slow since the units of low-levels of design abstraction are transistors or gates. But designers need reliable power estimates early in the design process. Therefore designers need to have tools for fast and accurate power estimation at higher levels of design abstraction such as the Register Transfer Level (RTL).

This thesis introduces a new method for RTL …

Recovery Of Intracellular Materials By Electroporation, Wendy Elaine Reid

Theses

Electroporation is commonly used to transfer genetic materials such as DNA into the cell by exposing the cell to a high electric field that momentarily permeabilizes the cell membrane. This premise was utilized to use electroporation as a means of releasing intracellular proteins. A procedure has been developed for the release of intracellular proteins through the use of electroporation. This procedure is a breakthrough. In general, industrial scale techniques to recover proteins from microorganisms are inefficient (Clarkson, 1993). A benefit of this electroporation-based mechanism would be the reduction of steps in the downstream processing required to purify the desired product. …

Electromagnetic Beam Directing Means-Sample Analysis System Stage, And Method Of Use, Daniel W. Thomspon, Darin W. Glenn, John A. Woollam

Department of Electrical and Computer Engineering: Faculty Publications

Disclosed is an electromagnetic beam directing means for use with sample analysis systems, such as relfectometers, ellipsometers and polarimeters and the like, use of which facilitates investigation of sample systems which are not mounted to a sample analysis system sample system supporting stage. The present invention eliminates the requirement os extensice sample analysis system component realignment when alternatingly performing analysis of sample systems mounted upon, and mounted other than upon, a sample analysis system sample system supporting stage.

Performance And Robustness Issues In The Compensation Of Folpd Processes With Pi And Pid Controllers, Aidan O'Dwyer

Conference papers

This paper will discuss the compensation of first order lag plus time delay (FOLPD) processes using PI and PID controllers whose parameters are specified using appropriate tuning rules. The gain margin, phase margin and maximum sensitivity of the compensated system as the ratio of time delay to time constant of the process varies, are used as ways of judging the performance and robustness of the system.

The Gain Scheduled Piece-Wise Adaptive Digital Control Of A Ph Process, Eugene O'Shaughnessy, Aidan O'Dwyer

Conference papers

The compensation of a pH process is complicated by the non-linear nature of the process titration curve and the significant time delays that typically exist in such processes. This paper will propose the use of a gain scheduled piecewise adaptive PI controller to compensate the process. A pilot plant is controlled, with the control algorithm implemented on a programmable controller. SCADA software displays and trends the plant and controller signals.

Nonlinear Modeling Of Concrete-Filled Frp Tubes Using The Finite Element Method, Kenneth T. Zagers

Retrospective Theses and Dissertations

Fiber reinforced plastic (FRP) has in recent years emerged as an alternative reinforcement for structural concrete. The properties that make FRP appealing to the construction industry include its resistance to electro-chemical corrosion, high strength-to-weight ratio, and electrical insulation. An efficient use of FRP is in the form of concrete-filled tubes, where the tube not only protects the concrete against environmental factors, but also provides confinement and external reinforcement. Since use of fiber composites for confining concrete is relatively new, analytical work in this area is limited to the models that were originally developed for transverse steel reinforcement. However, it has …

Emerald: A Low-Cost Spacecraft Mission For Validating Formation Flying Technologies, Robert J. Twiggs, Jonathan How, Christopher Kitts

Robert "Bob" Twiggs STEM Education Collection

A published report by Bob Twiggs, Jonathan How, and Christopher Kitts titled "EMERALD: A Low-Cost Spacecraft Mission for Validating Formation Flying Technologies" from 1998.