Engineering Commons^™

A High Frequency Memristor Emulator Circuit, Manu Chilukuri

Electrical Engineering Theses - Archive

In this thesis, a low power, high frequency memristor emulator has been designed. The purpose of emulator circuit is to mimic the behavior of a memristor. The circuit consists of a summing amplifier, an integrator and a multiplier. The circuit has been implemented using commercial off the shelf (COTS) components in Keysight ADS simulation tool. For CMOS implementation, the emulator circuit has been designed using IBM 0.18um technology. The design of each circuit has been explained in this work. The Opamp designed achieves a gain of 89 dB, output swing of 1.584V and a bandwidth of 3.67 MHz. The circuit …

Multi-Stage Prediction Scheme For Screen Content Based On Hevc, Nagashree Mundgemane Nagaraj

Electrical Engineering Theses - Archive

Screen content is a computer generated content which contains text, graphics and animations and the coding of such content is different from coding a photographic content. This thesis emphasizes on coding the screen content keeping the present video coding standard High Efficiency Video Coding (HEVC) as the base. An extension to HEVC to support screen content coding (SCC) is currently under development by the Joint Collaborative Team on Video Coding (JCT- VC) and the main goal of the extension is to provide improved compression performance of text, graphics and animation in addition to photographic content. This thesis focuses on a …

Reducing The Encoding Time Of Motion Estimation In Hevc Using Parallel Programming, Vasavee Vijayaraghavan

Electrical Engineering Theses - Archive

High Efficiency Video Coding (HEVC) is the current state-of-art video codec which is widely being adopted by lot of users. It has close to 50% reduction in encoding time compared to its predecessor, H.264 or AVC (Advanced Video Coding) at the cost of increased complexity. Lot of research is going towards reducing the complexity of this codec, at the same time, maintaining the visual quality that it produces and maintaining the reduced encoding time from its predecessor. As an effort to decrease the encoding time further, there can be several approaches. Parallel processing is taking a dominant role in many …

Machine Components Test, Brandon Younger, Lauren Romero, Carlos Padilla

Mechanical Engineering

To enhance California Polytechnic State University’s Mechanical Engineering program, Dr. Schuster has sponsored Brandon Younger, Lauren Romero, and Carlos Padilla to design and develop a new lab for students in the Intermediate Design class to test real mechanical components. This report discusses the background and ideation process that lead to the development of the Educational Mechanical Breadboard for Transmission System Components (Machine Components Test). Additionally, detailed drawings, 3D modeling, testing plans, and analysis are included to show how the Machine Components Test design will work and be validated.

Carbon Articulating Backpack Spine, Salvatore Monforte Iii, Darci Lawrence, Savan Patel

Mechanical Engineering

In the field, firefighters and Urban Search and Rescue (USAR) personnel need to transport variable loads efficiently, safely, and comfortably while simultaneously performing certain physical tasks. Current models of external and internal framed backpacks distribute the load of a pack efficiently, but do not allow for the natural movement of the wearer. Wolfpack Gear, Inc. proposed the need for a system which both effectively carries a load and allows for the unhindered natural movement of the user. The goal of this project was to design, build, and test an articulating backpack support system. The first stage of the project comprised …

Squirting Balloon Toy, Rachael Schelley, Elizabeth Wilhelm

Mechanical Engineering

The main goal of the Squirting Balloon Toy project was to create a new toy that combined both a helium balloon and a squirting water component near the base of the balloon. The toy will be sold at theme parks, fairs, and to other retailers such as toy stores with the target audience of primarily children and their parents, or any individuals seeking a good laugh when they spray their unsuspecting target. As a result, the toy was designed to be both visually appealing and to have an element of surprise. After testing and analyzing four different conceptual designs, two …

Gaf Glass Mat Splice Table Improvements, Grant Haug, Kevin Lansang, Ronald Lam, Michael Mooney

Mechanical Engineering

The GAF asphalt shingle production line in Shafter, CA requires continuous operation in order to maximize production efficiency. The assembly line process begins with feeding a large roll of fiberglass web into an accumulator. However, once the fiberglass roll approaches the end, it must be spliced with a new roll in order to maintain continuous feed into the production line. The splicing process must be fast and reliable to prevent any delay of the production line. Currently, this process is performed by two workers who manually feed the new fiberglass roll, align the two mats, cut the mats, apply glue …

Hands-Free Computer Interaction Using A Sip/Puff Sensor As A Mouse, Daniel Williams

Computer Engineering

No abstract provided.

Real-Time Digital Effects Processing Using Ios, Jonah W. Clinard

Computer Engineering

In today’s society, we are seeing incredible improvements in terms of creating smaller technological devices that behave more and more like the personal computers of yesterday. Mobile “Smart” devices, in particular, are becoming incredibly powerful not just in terms of processing power, but in the fact that they are able to provide assistance to users in their everyday lives. Application developers are now able utilize the power and size of these devices, to create and realize ideas that would have been previously viewed as impossible. This project applies the fields of digital signal processing, music, and mobile application development, to …

A Study On General Assembly Line Balancing Modeling Methods And Techniques, Bryan Pearce

All Dissertations

The borders of the assembly line balancing problem, as classically drawn, are as clear as any other operations research topic in production planning, with well-defined sets of assumptions, parameters, and objective functions. In application, however, these borders are frequently transgressed. Many of these deviations are internal to the assembly line balancing problem itself, arising from any of a wide array of physical or technological features in modern assembly lines. Other issues are founded in the tight coupling of assembly line balancing with external production planning and management problems, as assembly lines are at the intersection of multiple related problems in …

Properties Of Pan Fibers Solution Spun Into A Chilled Coagulation Bath At High Solvent Compositions, E. Ashley Morris, Matthew C. Weisenberger, Gregory Wilson Rice

Center for Applied Energy Research Faculty and Staff Publications

In this work, multifilament, continuous polyacrylonitrile (PAN) fiber tow was solution spun mimicking industrial processing at the small pilot scale (0.5 k tow), while carefully altering the composition of the coagulation bath, in order to determine the effect on the resulting fiber shape, density, orientation, and tensile properties at varying points in the spinning process. Novel here are the abnormally high coagulation bath solvent compositions investigated, which surpass those often reported in the literature. In addition, the coagulation bath was maintained at a slightly chilled temperature, contrary to reported methods to produce round fibers. Further, by altering the composition of …

The Bounded Edge Coloring Problem And Offline Crossbar Scheduling, Jonathan Turner

All Computer Science and Engineering Research

This paper introduces a variant of the classical edge coloring problem in graphs that can be applied to an offline scheduling problem for crossbar switches. We show that the problem is NP-complete, develop three lower bounds bounds on the optimal solution value and evaluate the performance of several approximation algorithms, both analytically and experimentally. We show how to approximate an optimal solution with a worst-case performance ratio of 3/2 and our experimental results demonstrate that the best algorithms produce results that very closely track a lower bound.

Faster Maximium Priority Matchings In Bipartite Graphs, Jonathan Turner

All Computer Science and Engineering Research

A maximum priority matching is a matching in an undirected graph that maximizes a priority score defined with respect to given vertex priorities. An earlier paper showed how to find maximum priority matchings in unweighted graphs. This paper describes an algorithm for bipartite graphs that is faster when the number of distinct priority classes is limited. For graphs with k distinct priority classes it runs in O(kmn1/2) time, where n is the number of vertices in the graph and m is the number of edges.

Three Degree-Of-Freedom Parallel Actuator Telescope Mount, Garrett Daniel Gudgel

Master's Theses

This thesis contains the design, implementation, and testing of an original, small-scaled two degree-of-freedom telescope mount and a medium-scaled three degree-of-freedom telescope mount inspired by the six degree-of-freedom Stewart-Gough platform telescope mount. The end product is intended to achieve research-standard resolution of targeted sky coverage for binary star research. The scaled prototype was carried through concept design, manufacturing, software development, and testing. The mount software development and electronic design is applicable to a full-scale mount as the drivers have been designed to be easily adapted to different actuator configurations. It is recommended that this design be implemented into a telescope …

Ergonomics Analysis Of Touchscreen Utilization As A Function Of Preferred Hand And Gender, Jordan E. Odell

Master's Theses

The growth of touchscreen technology has changed the way users interface with a wide range of computing and communication products and systems. Examples range from personal tablets and laptops to industrial applications such as process control, point-of-sales, and ticketing kiosk systems. An important area of application is the automobile industry which is designing cars with touchscreen control panels to replace the previously designed mechanical knobs and buttons. However, interacting with touchscreens does not provide the same tactile feedback as physical mechanisms, therefore they require more precise movement and visual attention, which distracts the user from the primary task.

The purpose …

Inductive Monitoring Systems: A Cubesat Ground-Based Prototype, Michelle Haddock

Master's Theses

Inductive Monitoring Systems (IMS) are the newest form of health monitoring available to the aerospace industry. IMS is a program that builds a knowledge base of nominal state vectors from a nominal data set using data mining techniques. The nominal knowledge base is then used to monitor new data vectors for off-nominal conditions within the system. IMS is designed to replace the current health monitoring process, referred to as model-based reasoning, by automating the process of classifying healthy states and anomaly detection. An IMS prototype was designed and implemented in MATLAB. A verification analysis then determined if the IMS program …

Two-Phase Anaerobic Digestion To Reduce The Nox Emission Potential Of Biogas, Nathaniel Manuel Olivas

Master's Theses

Anaerobic digestion can be used to decrease the mass of organic wastes to be disposed of while producing useful biogas (CH₄ and CO₂) for heat or power production, but in air basins with strict emissions limits, biogas combustion is difficult to implement due to the high costs of controlling NOx emissions. NOx production can be minimized by blending H₂ gas with CH₄ at a volume ratio of 15:85 H₂:CH₄, which allows burning at ultra-lean air-to-fuel ratios. For biogas systems, a potential low-cost NOx control strategy is to produce H₂-CH …

Process Development For Compression Molding Of Hybrid Continuous And Chopped Carbon Fiber Prepreg For Production Of Functionally Graded Composite Structures, Corinne Marie Warnock

Master's Theses

Composite materials offer a high strength-to-weight ratio and directional load bearing capabilities. Compression molding of composite materials yields a superior surface finish and good dimensional stability between component lots with faster processing compared to traditional manufacturing methods. This experimental compression molding capability was developed for the ME composites lab using unidirectional carbon fiber prepreg composites. A direct comparison was drawn between autoclave and compression molding methods to validate compression molding as an alternative manufacturing method in that lab. A method of manufacturing chopped fiber from existing unidirectional prepreg materials was developed and evaluated using destructive testing methods. The results from …

College Football Rankings: Maximum Flow Model, Jaymin Patel

Industrial Engineering Undergraduate Honors Theses

College football is a very popular sport in the United States. There is much debate over the college football rankings every week. A maximum flow network is implemented into the CMS+ rankings to observe the effects it has on the college football rankings.

Enhanced Shrinkage Characterization Of Clayey Soils, Raju Acharya

Civil Engineering Dissertations - Archive

Surficial slope failure is a common problem experienced by most of the compacted earth dams in Texas and several other southern states in USA as a result of desiccation or shrinkage induced cracking of the surficial soils. Cracking of the soil occurs when the tensile stress exceeds the tensile strength during drying process. Tensile stress increases with an increase in shrinkage strain and thus soil chemical admixtures can reduce the tensile stress by reducing the shrinkage potential of soil. Inclusion of such admixtures invariably affects the tensile strength. Yet there are not many test methods that could be utilized for …

Supervised Machine Learning For Classification Of The Electrophysiological Effects Of Chronotropic Drugs On Human Induced Pluripotent Stem Cell-Derived Cardiomyocytes, Christopher Heylman, Rupsa Datta, Agua Sobrino, Steven George, Enrico Gratton

Biomedical Engineering

Supervised machine learning can be used to predict which drugs human cardiomyocytes have been exposed to. Using electrophysiological data collected from human cardiomyocytes with known exposure to different drugs, a supervised machine learning algorithm can be trained to recognize and classify cells that have been exposed to an unknown drug. Furthermore, the learning algorithm provides information on the relative contribution of each data parameter to the overall classification. Probabilities and confidence in the accuracy of each classification may also be determined by the algorithm. In this study, the electrophysiological effects of β–adrenergic drugs, propranolol and isoproterenol, on cardiomyocytes derived from …

Analyzing General-Purpose Computing Performance On Gpu, Fanfu Meng

Master's Theses

ABSTRACT

Analyzing General-Purpose Computing Performance on GPU

Graphic Processing Unit (GPU) has become one of the most important components in modern computer systems. GPUs have evolved from a single -purpose graphic rendering hardware to a powerful processor that is capable of handling many different kinds of computing tasks. However, GPUs don’t perform well on every application, and it takes a lot of design effort to get good performance on a GPU.

This thesis aims to investigate the relative performance of a GPU vs. CPU. Design effort is held minimum for both CPU implementations and GPU implementations. Matrix multiplication, Advance Encryption …

Could Application Of Column-Grid-Array (Cga) Technology Result In Inelastic-Strain-Free State-Of-Stress In Solder Material?, Ephraim Suhir, Reza Ghaffarian, Johann Nicolics

Mechanical and Materials Engineering Faculty Publications and Presentations

Physically meaningful and easy-to-use analytical stress model is developed for a short cylinder (beam) clamped at the ends and subjected to bending caused by the ends offset. The offset is due, in its turn, to an external lateral force that has to be determined from the known offset. It is envisioned that such a beam can adequately represent the state of stress in a column-grid-array (CGA) solder joint interconnection experiencing thermal loading due to the thermal expansion/contraction mismatch of the IC package and the printed circuit board (PCB). The CGA designs are characterized by considerably higher stand-off heights than ball-grid-array …

A Quantified Approach To The Functional Longevity Of Geosynthetic Rolled Erosion Control Products (Grecps), Drew A. Loizeaux

Masters Theses and Doctoral Dissertations

Geosynthetic Rolled Erosion Control Products (GRECPs) have been utilized for decades in a multitude of applications to mitigate erosion resulting from land disturbance in civil construction projects. GRECPs vary from one type to another, ranging in performance and design life due to their composition and intended purpose. The coverage and durability of the GRECP are fundamental properties that can predict performance and fitness for use. Both coverage and durability will degrade over the design life of the GRECP to the point that fitness for use is unacceptable for the intended application. A standard approach is needed to quantify this material …

A Parabolized Navier-Stokes Method For Wind Farm Applications, Anshul Mittal

Masters Theses and Doctoral Dissertations

Fluid flow simulations play an important role in the wind industry. With the development of large wind farms, flow simulations through an entire wind farm are becoming a necessity. These are required for designing the layout of new wind farms in the development stage and for forecasting power production from the existing ones for operational purposes. Conventional Navier-Stokes simulations (commonly referred to as CFD simulations) are computationally very expensive since they require a supercomputer with runtimes of several weeks. A Parabolized Navier-Stokes (PNS) method is developed and implemented in this study. The developed PNS method requires less stringent approximations as …

Creating A Highway Information System For Safety Roadway Features, Brian K. Howell, Kenneth R. Agent, Eric Green

Kentucky Transportation Center Research Report

Roadway departures are the leading cause of roadside fatalities. The Kentucky Transportation Cabinet (KYTC) has undertaken a number of roadside safety measures to reduce roadway departures. Specifically, KYTC has installed several low-cost, systemic roadway safety treatments to Kentucky’s roadways in recent years. These treatments include cable barriers, high friction surface treatments, rumble stripes, and Safety Edges. KYTC has installed approximately 44 cable barrier systems over 265 miles of roadway,112 HFST applications over 20 miles of roadway, 750 rumble stripe installations over 2,500 miles of roadway, and 147 Safety Edge treatments on 580 miles of roadway. The project team developed a …

Understanding The Automotive Pedal Usage And Foot Movement Characteristics Of Older Drivers, Yubin Xi

All Dissertations

The purpose of this study was to understand the pedal usage characteristics of older drivers in various driving tasks using an instrumented vehicle. This study stemmed from the prevalence of the pedal application errors (PAEs) and the older drivers’overrepresentation in crashes caused by PAEs.

With the population increasing and becoming older, it is estimated that in 2020 there will be 40 million drivers over the age of 65 in the United States. Compared with their younger counterparts, older drivers are facing declining cognitive and physical abilities, such as impaired vision, slower reaction time and diminishing range of limb motion. Because …

An Investigation Of Cooling Configurations In Gas Turbine Engines Using Jet Impingement, Bhushan Upalkar

Doctoral Dissertations and Master's Theses

A numerical investigation for predicting the heat transfer effects of turbulence was conducted by making a scaled-up model of a section in a jet impingement channel. Different turbulence models were run and the results were compared to experimental data. Experimental comparisons were made for impingement channels between a baseline case, which is a rectangular array of jets of 20 rows and 3 jets per row, and different hole spacing configurations. The heat transfer was measured using Temperature Sensitive Paint. The turbulence model v²-f gave the most accurate prediction with an error of about 17% with the EB k-E, with an …

Simulation Of Lateral Migration And Sedimentation Of A Flexible Fiber In A Vertical Weak Shear Flow, Ali Ibrahim Neamah Neamah

Masters Theses

This research is a thorough numerical investigation and critical analysis of lateral migration of a deformable particle settling in a vertical weak shear flow. Under the vertical weak shear fluid, the deformable particle may move either to the coagulation area, or the dispersion area, depending on Reynolds numbers, shear Reynolds number, fiber flexibility, and aspect ratio. In this study, a lattice Boltzmann equation is used to solve Navier-Stokes equation and a flexible particle method is employed to attack the problem of motion of a flexible fiber. A bounce-back rule is used to deal with moving boundaries interacting with fluids. Several …

An Introduction To Defining Cost Estimates For Mechanical And Electrical Services Using The Nrm1, Charles Mitchell

Reports

Determining an accurate value for the supply and installation of mechanical and electrical services is a difficult task due to the level of specialisation and variance within this sector of the industry. The level of specialised knowledge and the ever changing technology has prevented the Quantity Surveyor from taking a firm hold on the cost estimation of these services. Cost estimates have previously been prepared by consultant services engineers or based on costs provided by these consultants.

However, employers nowadays require more cost certainty in the estimates of costs. As a direct result the New Rules of Measurement 1 (NRM1) …