Engineering Commons^™

Modeling Of Cloud-Based Digital Twins For Smart Manufacturing With Mt Connect, Liwen Hu, Ngoc-Tu Nguyen, Wenjin Tao, Ming-Chuan Leu, Xiaoqing Frank Liu, Rakib Shahriar, S M Nahian Al Sunny

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The common modeling of digital twins uses an information model to describe the physical machines. The integration of digital twins into productive cyber-physical cloud manufacturing (CPCM) systems imposes strong demands such as reducing overhead and saving resources. In this paper, we develop and investigate a new method for building cloud-based digital twins (CBDT), which can be adapted to the CPCM platform. Our method helps reduce computing resources in the information processing center for efficient interactions between human users and physical machines. We introduce a knowledge resource center (KRC) built on a cloud server for information intensive applications. An information model …

Pressure Ulcer Prevention System, Rey-David Palomares, Ojus Rao

Interdisciplinary Design Senior Theses

Pressure ulcers, also known as bedsores, are a widespread but often understated problem. A pressure ulcer is an injury that develops with constant pressure on an area of skin for a long time. They range from bruises to open wounds to even exposed bone. These injuries especially impact bedridden and elderly hospital inpatients, since these people must depend on nursing staff for mobility.

Pressure ulcers can seem to be a solved problem. Solutions that completely eliminate pressure ulcers do exist. These solutions, however, are too expensive for widespread use, at thousands of dollars per bed. Other solutions, such as relying …

Membrane Deflection-Based Fabrication And Design Automation For Integrated Acoustofluidics, Daniel Freitas

Electrical and Computer Engineering Master's Theses

Continuous-flow microfluidic large-scale integration (mLSI) is a developing field first introduced in the early 2000s, that continues to offer promising solutions to many biochemical, biophysical and biomedical problems. In his seminal paper, Thorsen et al. 2002 demonstrated the fabrication of high-density microfluidic systems capable of complex fluidic routing in combinatory arrays of multiplexors, mixers, and storage assemblies integrated with micromechanical valves. mLSI has been a powerful tool for scientific research by allowing for dramatic reduction in the volume of reagent needed for experimentation and offering highly parallelizable and dynamic process flows. These systems have since been the focus of strong …

3d Printed Soft Robotic Hand, Zack Kisner, Chris Szigeti, David Leonardo

Mechanical Engineering Senior Theses

Soft robotics is an emerging industry, largely dominated by companies which hand mold their actuators. Our team set out to design an entirely 3D printed soft robotic hand, powered by a pneumatic control system which will prove both the capabilities of soft robots and those of 3D printing. Through research, computer aided design, finite element analysis, and experimental testing, a functioning actuator was created capable of a deflection of 2.17” at a maximum pressure input of 15 psi. The single actuator was expanded into a 4 finger gripper and the design was printed and assembled. The created prototype was ultimately …

6u Cubesat Platform For Disaster Relief Communications, Uchechukwu Agwu, Duncan Bradley, Corey Brown, Mani Gnanasivam, Grant Mishler, Steven Parks

Mechanical Engineering Senior Theses

Natural disasters can seriously damage telecommunications infrastructure in affected areas, drastically limiting the channels of communication between locals and emergency relief teams. In such situations it is critical to have readily-available communications infrastructures that can be deployed and utilized as soon after the event as possible. Our mission is part of a multi-year effort to provide satellite-based amateur radio communications to areas impacted by humanitarian crises to facilitate relief efforts. Specifically, we developed the mechanical subsystems of a 6U CubeSat, a small satellite, in order to provide expanded volume, enhanced power generation, and Earth referenced orientation control compared with previous …

Active Control Stabilization Of High Power Rocket, Valeria Avila Guerrero, Angel Barranco, Daniel Conde

Mechanical Engineering Senior Theses

High power rockets could become dynamically unstable due to outside disturbances after takeoff. The instability is augmented when the rocket is "slow" off the launch rail, which happens when the thrust-to-weight ratio is less than 5:1. Due to these reasons, the objective of this project was to design and build an active control system that will make sure the rocket follows a straight path all the way to apogee. This will be done through a model-based design approach, in which a 6DOF mathematical model of the flight dynamics will be created.

Vibration Attenuating Medical Platform, Cameron Fisch, Noah Friedman, Tyler Gambill, David Harris, Kelek Olais

Mechanical Engineering Senior Theses

Millions of injured people are transported by ambulances each year. While the suspension systems of ambulances dampen the road vibrations felt by the passengers, they do not attenuate the vibration completely. To patients who have compromised physical states, vibration and displacement can aggravate their condition and cause additional pain. Our solution to this societal problem is the Vibration Attenuating Medical Platform (VAMP). VAMP consists of an aluminum and steel structure that is moved with a pneumatic piston. This prototype is designed to fit into existing ambulances and attenuate the vibrations not eliminated by the ambulances suspension. After conducting background research, …

An Integrated Decision Support Framework For Life-Cycle Building Asset Management, Maha Reda Alkasisbeh

Dissertations

Building assets are essential to the economic, cultural, and historical growth of any nation. Examples of buildings include shelters, entertainment facilities, living spaces, teaching facilities, civil offices, parking structures, police buildings, libraries, and service areas used to accommodate human activity. Deterioration of building assets, inadequate renewal budgets, climbing deficits, and increasing demand levels are difficulties that face owners when managing building assets. The role of asset management has recently become significant in municipal governments for strategic, operational, and financial reasons. The main functions of an asset management system include assessment of the current condition, prediction of future deterioration, asset prioritization, …

Book-Hunt! Android Mobile Application Using Indoor Positioning Technology, Sneha Pantam

Electronic Theses, Projects, and Dissertations

Indoor Positioning System (IPS) focuses on locating objects inside

Buildings. Till date, GPS has helped us obtain accurate locations outdoors. These locations have helped us in many ways like navigating to a destination point, tracking people etc. Indoor Positioning System aims at navigating and tracking objects inside buildings. [1] IndoorAtlas is a technology that works on the theory of Indoor Positioning System. Book-Hunt is an Android mobile application which majorly makes use of IndoorAtlas therefore making use of the technique of indoor tracking. This Android mobile application is designed for Libraries. It is designed specifically for John M. Pfau Library, …

Integrating Statistical Methods In Engineering Technology Courses, Sanjeevi Chitikeshi, Jake Hildebrant, Otilia Popescu, Orlando M. Ayala, Vukica M. Jovanovic

Engineering Technology Faculty Publications

Statistical methods and procedures are very important in engineering applications. In most of the engineering fields electronic devices are used as sensing and controlling components. Lack of proper calibration of these devices and of performance analysis using different statistical methods may lead to erroneous measurements and results. In medical or manufacturing areas such errors in the experimental results could be catastrophic. Applying different statistical tests and procedures enhance the quality of engineering work. Traditionally, most engineering curricula have at least one required course in applied statistics in engineering, but that is not generally the case in engineering technology programs. Most …

Test Method For Predicting Failure Modes In Protective Films, Aubrey Jeanette Decker

Theses and Dissertations

In the business of packaging engineering, a large consumption of time is placed on evaluating new materials to provide cost savings to a company. This evaluation is made by using test methods such as those found in ASTM D4169-16, which helps to simulate shipping and distribution conditions. A key problem is that this test method can take up to multiple months, and sometimes years to complete. The apparatus created in this study allows for a comparison to be made between currently used films and prospective films in approximately ten hours. This allows for a prescreening of new films to be …

Hardware And Software Improvements To A Low-Cost Holographic Video Monitor, Andrew August Henrie

Theses and Dissertations

The "Mark V" Holographic Video Monitor ("HoloMonitor") is a continuation of effort and accomplishments to produce a low-cost device capable of reproducing true full-color horizontal-parallax-only computer-generated holograms at typical video frame-rates. While other devices around the world may have greater capabilities, these devices are currently confined to laboratory settings due to their sheer complexity and expense. The aim of this project is to provide researchers and "tinkerers" with a device capable of recreating holographic effects in full color, respectable resolution, in real time, and at a comparatively low cost. The "Mark V" HoloMonitor is a closer representation of a consumer …

Crash Severity Distributions For Life-Cycle Benefit-Cost Analysis Of Safety-Related Improvements On Utah Roadways, Conor Judd Seat

Theses and Dissertations

The Utah Department of Transportation developed life-cycle benefit-cost analysis spreadsheets that allow engineers and analysts to evaluate multiple safety countermeasures. The spreadsheets have included the functionality to evaluate a roadway based on the 11 facility types from the Highway Safety Manual (HSM) with the use of crash severity distributions. The HSM suggests that local agencies develop crash severity distributions based on their local crash data. The Department of Civil and Environmental Engineering at Brigham Young University worked with the Statistics Department to develop crash severity distributions for the facility types from the HSM.The primary objective of this research was to …

High Throughput Fpga Configuration Using A Custom Dma Configuration Controller, Peter William Zabriskie

Theses and Dissertations

SRAM-based Field Programmable Gate Arrays (FPGAs) must be programmed with configuration data every time they are powered on. In addition to initially programming an FPGA, there are many other applications that require access to FPGA configuration memory such as partial reconfiguration, fault injection, and memory scrubbing. This thesis describes a system that provides high-speed, programmable configuration management for Xilinx FPGAs through external interfaces. This system is an improvement upon the JTAG Configuration Manager (JCM) previously created at BYU. The JCM consists of a custom I/O board paired with a MicroZed development board which includes a Xilinx ZYNQ SoC. This platform …

Using Quantitative Mri To Measure Cartilage Health, Laurel Jane Hales

Theses and Dissertations

Osteoarthritis (OA) is one of the leading causes of disability world-wide. It affects 12% of all Americans ages 25-74 [1]. One of the challenges with OA, is that there are currently no clinically viable methods to measure the health of the cartilage before cartilage loss. There are no ways to replace or heal the cartilage after it has been lost. It is known that the early stages of OA involve a decrease in the amount of glycosaminoglycans (GAG), one of the main molecules in cartilage. This decrease in GAG leads to a change in the fixed charge density of the …

Adjustment Of Rapidscat Backscatter Measurements For Improved Radar Images, Garrett Scott Mcdonald

Theses and Dissertations

RapidScat is a spaceborne wind scatterometer mounted on the International Space Station (ISS). The RapidScat mission lasted from September 2014 to November 2016. RapidScat enables the measurement of diurnal patterns of sigma-0 measurements. This capability is possible because of the non-sun-synchronous orbit of the ISS, in which the local time of day (LTOD) of sigma-0 measurements gradually shifts over time in any given location. The ISS platform is a relatively unstable platform for wind scatterometers. Because of the varying attitude of the ISS, RapidScat experiences a constant variation of its pointing vector. Variations of the pointing vector cause variations in …

Parametric Study On Multi-Story, Partially Grouted, Perforated, Masonry Shear Walls By Finite Element Analysis, Kyle Henry Chavez

Theses and Dissertations

In this study, parameters related to material properties, geometry, and external stimuli were examined individually to determine their influence on multi-story, partially grouted, perforated (openings), masonry shear walls using a finite element software FormWorks. The parameters studied were: the strength of grouted masonry prisms f'_m,grouted; the strength of un-grouted (hollow) masonry prisms f'_m,ungrouted; the ratio of mortar shear strength to masonry compressive strength; vertical and horizontal reinforcement ratios in terms of size and spacing of reinforcement; axial load; aspect ratio; and openings that were vertically and horizontally altered. To perform this study, finite element models were …

Laser Triangulation Sensor, Jake Finelt, Kian Gruszczynski, Greg Mclorg

Mechanical Engineering

Statement of Disclaimer: Since this project is a result of a class assignment, it has been graded and accepted as fulfillment of the course requirements. Acceptance does not imply technical accuracy or reliability. Any use of information in this report is done at the risk of the user. These risks may include catastrophic failure of the device or infringement of patent or copyright laws. California Polytechnic State University at San Luis Obispo and its staff cannot be held liable for any use or misuse of the project.

Identification System For Heart Valve Manufacturing, Nicholas Robert Jensen, Edgar Davis Nix, Judith Evelyn Gonzalez, Albert Austin Liddicoat

Mechanical Engineering

Abstract withheld due to NDA constraints

Treadmill User Centering, Cecilia Hill Yan Yuen, Donavan Chandler Feliz, Ariel Mae Arce Crisostomo, Adam Charles Patrella

Mechanical Engineering

The goal of team CENTREAD was to design a device to allow a person with a visual disability to run efficiently and effectively on a treadmill without fear of falling off or injuring themselves. The customer wished for the device to be small, lightweight, and have an easy, autonomous setup, while providing feedback to the user wirelessly for them to correct their own movement. The ultimate goal of the device is to allow the user to be comfortable, safe, and free while using it in order to ensure they have the best running experience. The device utilizes ultrasonic sensors in …

Foot Stress And Blood Flow Sensing Under High-Loading During Hip Surgery, Chris Cardenas, Esther Chen, Claire Kingston, Katie Paswaters, Brianna Rodebaugh

Mechanical Engineering

The PolyHIPS team was tasked with integrating sensors into Stryker’s hip arthroscopy boot that monitor blood flow and heel slip during hip surgery. During hip arthroscopy, the femur head is distracted from the acetabulum to create space in the joint for the surgeon to operate. This requires the use of up to 200 lbf. In order to maintain this space, the foot is held tightly in the boot. Complications can result from the foot being held too tightly in the boot during the procedure. The most common complication is neuropraxia, or temporary nerve damage. PolyHIPS proposes a solution that utilizes …

Nathan's Mobility Device, Steven A. Decsesznak, Matthew Brenholdt, Lansen Eto, Moulay Salahdin

Mechanical Engineering

Nathan’s Mobility Device is a California Polytechnic State University senior project composed of a team of four mechanical engineering students that designed, built and implemented a specialized seat on an existing mobility device. Nathan, the sole beneficiary of this project, is an 11-year-old boy afflicted with a condition known as Spinal Muscular Atrophy (SMA) which causes him extreme muscular weakness. In this report, the team discussed the problem at hand, provides preliminary research and product benchmarking (evaluation and comparison to specific criteria), and described the ideation, prototyping, testing, and iteration plan. In addition, the team explored the final design in …

Transcatheter Heart Valve Leaflet Assembly Tooling Improvement Final Design Report, James Craig Sherman, Zachary Robert Dicks, Luke Edward Williams

Mechanical Engineering

Statement of Confidentiality: The complete senior project report was submitted to the project advisor and sponsor. The results of this project are of a confidential nature and will not be published at this time.

Composite Suspension For A Mass Market Vehicle, Sarah M. Chapiama, Brian Auyeung, Jose Guerrero, Ethan Lau

Mechanical Engineering

Statement of Confidentiality: The complete senior project report was submitted to the project advisor and sponsor. The results of this project are of a confidential nature and will not be published at this time.

Curb Navigation, Cole A. Tudor, Kaitlyn R. Adams, Robbie Huerta

Mechanical Engineering

The Curb Navigation senior project, proposed by the QL+ organization, was presented to find a solution to an issue a former veteran, Velette, is having. Velette has a difficult time maneuvering curbs when out doing day-to-day errands and activities. The goal of this project is to develop a solution that will give Velette the ability to traverse curbs without the assistance of others or the need to do a wheelie that can lead to an injury. The team has found that adapting and optimizing an anti-tipper design may be the best way to solve the proposed challenge. The team decided …

Driver Cooling System, Joseph Fatin Bolous, Jake Donald Deboer, Alvin Theodore Lau

Mechanical Engineering

This document provides our Final Design Review (FDR) for the Driver Cooling System Project. It contains our background research, which includes current product research, technical research, and information on our sponsor’s needs as a customer as well our manufacturing process, test results, and final design. We created a problem statement to define the scope of the project, discuss sponsor and consumer needs and wants, and technical specifications. After brainstorming, we ultimately selected a thermoelectric cooling system (TEC) after presenting our Preliminary Design Report and Critical Design Report. We built the final prototype, as can be seen in the manufacturing plan, …

Dynamic Model For Simulating Motion Of The Right Ventricle, Brian Michael Larsen, Sam Koopman Porter, John Francis D'Ambrosio

Mechanical Engineering

This report documents all the research, ideation, and mockups used to determine right ventricle motion and develop a system capable of reproducing that motion on a tissue sample. The model is intended for evaluating anchoring systems being developed by Edwards Lifesciences for use with tricuspid valve therapies. Several design solutions were considered for the primary functions of recreating motion of the right ventricle and attaching tissue to the device. From these ideas a primary means of producing motion and attaching tissue was selected. These ideas were then developed over the course of a school year to become the final system …

Additive Manufacturing Powder Removal, Madison A. Lignell, Tyler W. Laird, Kurt K. Reed

Mechanical Engineering

Metal powder-bed fusion is an additive manufacturing process which enables the creation of unique shapes in metal parts that would otherwise be difficult, expensive, or impossible to machine. Metallic powder is melted and fused together by either a laser or electron beam to produce parts quickly. The excess powder covers newly printed parts and can be difficult to remove from small internal features. The scope of this project is to design a device that effectively removes the powder from newly printed parts safely, while reclaiming as much powder as possible for reuse. The solution for this project must be able …

Mechanical Team Final Design Report: Same Polytechnic College, Meghan L. Smith, Katie D. Nute, Long T. Hoang

Mechanical Engineering

The purpose of this document is to communicate the research, findings, and recommendations of the mechanical engineering team regarding the Same Polytechnic College project. This report includes a discussion of the design process utilized by the interdisciplinary team to construct preliminary building designs for both classroom and dormitory building modules. The mechanical team conducted testing using the wind tunnel to verify major building envelope design decisions. The following report also includes an explanation of the thermal testing that the team conducted to measure the thermal conductivity, diffusivity, and specific heat of bricks made to mimic those made locally in Same, …

3-Dimensional Automated Heat Flux Calibration Device, Victor Raul Chacon, David Madison Morrisset, Alex Michael Schnorr, Kevin Scott

Mechanical Engineering

This document aims to describe the problems in current radiant heat source heat flux calibration techniques and the approach our team took to solve them through automation. The following sections outline the basic premise of the problem we addressed and who our end product benefited. The proceeding sections addresses the research that we have performed regarding heat flux measurements and automation. This research includes current solutions – mostly partial solutions for problems that are similar but not exactly like ours. Following the background research, we define objectives, with specific details that outline how we evaluated different possible solutions, and how …