Heat Transfer, Combustion Commons^™

Direct Numerical Simulation Of Supercritical Co2 Mixing And Combustion, Syed Mohammad Ovais

All Dissertations

The supercritical CO₂ power cycle (sCO₂ ) is a relatively new technology, which promises to reduce CO₂ emissions with potentially higher efficiencies. However due to challenging conditions posed by supercritical pressures, the mixing and ignition phenomena in sCO₂ combustion is relatively less understood and studied. The primary objective of the current study is to investigate these fundamental processes using homogeneous ignition calculations (HMI) and direct numerical simulations (DNS). Broadly, the study is divided into two major parts. In the first part supercritical mixing in sCO₂ relevant conditions is investigated. To achieve this, DNS of temporally …

Experimental Evaluation Of Heat Leak From Anti-Sweat Components Into Fresh Food And Freezer Compartments Of A Household Refrigerator., Delva Felissaint

Electronic Theses and Dissertations

Condensation beads forming on outside surfaces around a refrigerator is an undesirable byproduct driven by the cold temperature exhibited throughout the unit. To combat this issue, anti-sweat components usually in the form of electrical heaters or tubes carrying hot refrigerant, bring heat to the cold surfaces to ensure their temperatures do not drop below the dew point. Some heat produced by the anti-sweat components may transfer to the interior refrigerated compartment. The purpose of this study is to quantify how much heat from the anti-sweat components are entering the fresh food and freezer compartments and what impact that has on …

Development And Applications Of A Sensor For Measurement Of Different Modes Of Heat Transfer On Foods In A Residential Oven., Kervins Petit-Bois

Electronic Theses and Dissertations

Thermal characterization of an oven is an important part of designing an oven. Understanding how changes in cooking algorithm, oven construction, and oven materials affect cooking performance is critical in ensuring that an oven is properly designed. Often temperature data is used to characterize oven behavior, but this neglects the mode of heat transfer used to achieve these temperatures. Several studies have compared the different modes of heat transfer and cooking performance and have shown that cooking performance in radiation dominated modes are different than in convection dominated modes. The goal of this study is to develop a heat flux …

Predictive Thermal Modeling And Characterization Of Ultrasonic Consolidation Process For Thermoplastic Composites, Madeline Kirby

LSU Master's Theses

Ultrasonic consolidation (USC) of thermoplastic composites (TPCs) is a highly attractive and promising method to manufacture high-performance composites. This work focuses on USC of dry carbon fiber (CF) fabrics with high-temperature polyphenylene sulfide (PPS) films. Experimental trials to assess feasibility of the process are time-consuming. Consequently, a predictive thermal model would facilitate process parameters selection to reduce expensive trial-and-error approaches. This paper presents a 2D finite element model of samples under consolidation, incorporating equations for viscoelastic heating, matrix phase change, and material properties. Theoretical temperature profiles for nodes of interest were compared to the corresponding experimental temperature curves for various …

Micro Heat Exchanger To Cool Cerebrospinal Fluid For Brain Injury Treatment, Sachin Dahiya

LSU Master's Theses

Hypothermia is accepted as a method to preserve cells and tissue. Clinical evidence shows that administration of hypothermia could lead to neuroprotection after cardiac arrest. Non-invasive methods such as surface cooling devices, drugs and cold liquid ventilation are available to induce hypothermia. These approaches for achieving hypothermia have not been optimized yet. The surface cooling methods are generally slow and may lead to additional thermal shock to the body. Here, we propose a rapid, selective cooling method for the brain using a micro heat exchanger to cool the cerebrospinal fluids (CSF). We designed and 3D printed a U-type heat exchanger …

Prediction Of Temperature Difference Across Thermoacoustic Stack Through Artificial Neural Network Technique, Anas A. Rahman, Xiaoqing Zhang

Future Engineering Journal

This study involved the application of artificial neural network (ANN) as a new approach for thermoacoustic refrigerators to predict the temperature difference across the stack under some operating conditions. One ANN model for a standing wave thermoacoustic refrigerator, had been developed based on the experimental data from other literature. Temperature difference across the stack was chosen as a response to the input parameters, mean pressure and frequency in the proposed ANN model. A multi-layer feed-forward neural network with a back propagation algorithm had been proposed for predicting the temperature difference across the stack of the thermoacoustic refrigerator. This proposed ANN …

Preliminary Study Of Shape-Memory Alloy Torsional Tubes As Thermal Management Actuators Under Non-Ideal Conditions, Paula Sanjuan Espejo, Samuel Desloover, Devon Hardy, Mark Ricklick, Frederick Calkin, David Foutch

Publications

Shape-memory alloys (SMAs) have been used in many engineering applications because of their shape-memory effect and pseudoelasticity. SMA behavior is well understood under steady and constant temperature and loading conditions, whereas transient and non-ideal conditions effects should be further investigated. In this research, SMA torque tubes are studied for use in thermal management applications as self-regulated actuators responding to a process fluid with changes in temperature, with the goal of improved system efficiency by keeping components at an optimal temperature. When utilized in a thermal management configuration, it is likely that the SMA’s thermal environment will be different than that …

Solid Thermal Storage As An Energy Storage Device In Insulated Solar Electric Cookers: Thermal Modeling And Experiment, Michael Antonio Fernandez

Physics

The use of solid thermal storage (STS) as an energy storage device in insulated solar electric cookers (ISEC) was explored using a thermal simulation before retrofitting an existing cooker without energy storage and testing it under several conditions. STS sizing, material selection, and geometry were examined from both theoretical and practical perspectives and re-examined following experimental results. Characterization of the system’s thermal interfaces and methods to improve their thermal conductivities were investigated resulting in several performance enhancements to the system.

Mmteg Heatsink Design, Peyton Nienaber, Kadin Feldis, Alec Savoye, Jack Waeschle

Mechanical Engineering

In this document, Cal Poly Senior Design Team F16 presents a summary of its work developing a suitable heatsink for Gas Technology Institute’s Methane Mitigation Thermoelectric Generator. After several months of iterating between experimental testing and simulated heat transfer, a suitable prototype was selected for use in further refining simulation parameters. This was called the structural prototype and it allowed Team F16 to confirm several remaining unknowns relating to component thermal conductivity. All documentation of this process can be found in Preliminary, Critical, and Interim Design Review documents (PDR, CDR, IDR), included in this report. Having a realistic model …

Insulated Solar Electric Cooker With Phase Change Materials, Weijun Zhao, Jake Lung, Owen Chu, Sarah Melzer

Mechanical Engineering

This Senior Project Report documents the development and design process of the Insulated Solar Electric Cooker with a Phase Change Material (ISEC w/ PCM). In this project, we developed a PCM assembly that can be integrated into an existing ISEC system which utilizes two 100 W solar panels. This report details the use of a nitrate salt solution of 60% NaNO3 and 40% KNO3 and demonstrates its potential as a viable form of thermal storage solution for cooking. We found that only 1kg of PCM is able to retain its heat for around 5 hours after power removal and believe …

Structural Sizing Of Post-Buckled Thermally Stressed Stiffened Panels, Walid Arsalane

Theses and Dissertations

Design of thermoelastic structures can be highly counterintuitive due to design-dependent loading and impact of geometric nonlinearity on the structural response. Thermal loading generates in-plane stresses in a restrained panel, but the presence of geometric nonlinearity creates an extension-bending coupling that results in considerable transverse displacement and variation in stiffness characteristics, and these affects are enhanced in post-bucking regimes. Herein a methodology for structural sizing of thermally stressed post-buckled stiffened panels is proposed and applied for optimization of the blade and hat stiffeners using a gradient-based optimizer. The stiffened panels are subjected to uniform thermal loading and optimized for minimum …

Lattice Boltzmann-Based Sharp-Interface Schemes For Conjugate Heat And Mass Transfer And Diffuse-Interface Schemes For Dendritic Growth Modeling, Nanqiao Wang

Theses and Dissertations

Analyses of heat and mass transfer between different materials and phases are essential in numerous fundamental scientific problems and practical engineering applications, such as thermal and chemical transport in porous media, design of heat exchangers, dendritic growth during solidification, and thermal/mechanical analysis of additive manufacturing processes. In the numerical simulation, interface treatment can be further divided into sharp interface schemes and diffuse interface schemes according to the morphological features of the interface. This work focuses on the following subjects through computational studies: (1) critical evaluation of the various sharp interface schemes in the literature for conjugate heat and mass transfer …

Development Of An Accelerated Life Testing Method For Reliability Assessment Of Wire Bonded Interconnects Subjected To Mechanical And Electromigratory Stresses, Whit Vinson

Graduate Theses and Dissertations

Power electronic advancement trends indicate that device power density will continue to increase as a result of increased power requirements and desired device form factor reduction in order to reduce weight and material costs and increase ease of integration into next-generation power systems. With these advancements come concerns regarding device reliability. The compounded effects of increased power density and form factor reduction in electrical conductors will yield amplified joule heating effects in addition to the already increasing device temperature profiles resulting from the incorporation of wide bandgap technology into power systems. Joule heating effects can lead to a variety of …

Nucleate Boiling Under Different Gravity Values: Numerical Simulations & Data-Driven Techniques., Sandipan Banerjee

Electronic Theses and Dissertations

Nucleate boiling is important in nuclear applications and cooling applications under earth gravity conditions. Under reduced gravity or microgravity environment, it is significant too, especially in space exploration applications. Although multiple studies have been performed on nucleate boiling, the effect of gravity on nucleate boiling is not well understood. This dissertation primarily deals with numerical simulations of nucleate boiling using an adaptive Moment-of-Fluid (MoF) method for a single vapor bubble (water vapor or Perfluoro-n-hexane) in saturated liquid for different gravity levels. Results concerning the growth rate of the bubble, specifically the departure diameter and departure time have been provided. The …

Fluid Structure Interactions Within A Common Rail Diesel Injector., Russell Prater

Electronic Theses and Dissertations

The internal flow of a high-pressure diesel injector is simulated numerically to investigate the complex transient flow structures and the unsteady forces imparted to the injector needle that result from the asymmetric flow fields developed during operation. The gas-liquid two phase flow is simulated using a mixture model with the cavitation numerically modeled using the Zwart-Gerber-Belamri model. Both the k-ε model and the detached eddy simulation (DES) model are used, and the numerical results are compared. This dissertation looks at the internal flow of a generic injector at different lifts and characterizes the flow parameters at high lift and low …

Generative Designs Of Lightweight Air-Cooled Heat Exchangers, Connor Miller

Mechanical Engineering Undergraduate Honors Theses

The development of high-performance air-cooled heat exchangers is required to permit the rapid growth of vehicle and aircraft electrification. In electric vehicles and airliners, the motors and power electronics are integrated into a compact space, leading to unprecedently high power density. To achieve higher overall thermal efficiency, the heat exchangers must be extremely light while maintaining their heat transfer performance and mechanical robustness. Recently advances in 3D metal printing, e.g., direct metal laser sintering, and selective laser melting, have enabled the manufacturing of high-performance robust heat exchangers by eliminating thermal boundary resistance and ensuring a uniform thermal expansion coefficient. Nonetheless, …

Durability Of Non-Metallic Materials For Additively Manufactured Heat Spreader Fabrication, Rafael Estrella

Mechanical Engineering Undergraduate Honors Theses

Power electronics are necessary to convert power from DC sources for AC applications. As this technology trends toward smaller packaging for denser power loads, the increased electrical losses result in deleterious excess heat. Thermal management devices are required to prevent the effects of thermal runaway from shortening the longevity of these modules. Nonmetallic jet impingement heat spreaders provide several benefits in terms of weight and performance over conventional cold plates while not accentuating EMI from the switches in the power module; however, the polymer makeup of the materials previously used for fabricating these devices raises durability concerns under the high …

Managing Humidity In Electronics Using Water Vapor-Selective Membranes, Songhao Wu, Andrew J. Fix, Allison Mou, David M. Warsinger, James Braun

Discovery Undergraduate Interdisciplinary Research Internship

Abstract: As outdoor electronics have become prevalent in every aspect of daily life, handling humidity in them is an emerging issue for reliable devices. As water vapor enters the electronics enclosure, there is a risk of condensation, which could prevent the electronics from functioning and further damage the device. Traditionally, the humidity removal for electronics is usually done by heating the air within the enclosure, which can be energy-intensive and less efficient. Vapor selective membrane systems are promising alternatives for air heating dehumidification as they do not require heating energy for water vapor removal. It allows water vapor transport through …

Triggering Thermal Runaway In Lithium-Ion Batteries, Chris John

Honors Scholar Theses

The proliferation of lithium-ion batteries enables electric devices such as cell phones to electric vehicles to become a reality. A latent danger, however, exists in these batteries. Mechanical, thermal, or electrical damage can initiate a phenomenon known as thermal runaway (TR). This damage causes internal short circuits within the battery, releasing heat and triggering exothermic decomposition reactions. The battery will catch fire if rapid cooling is not present. While experimental designs exist for evaluating TR, significant safety hazards and impracticality may impede testing efforts. Finite element analysis, therefore, becomes a vital tool in modeling TR and mitigation techniques. However, there …

Novel Thermal Coating For High-Speed Airplanes, Abinash Satapathy, Lakshay Battu, Liam Watson, Nazanin Rajabi

Symposium of Student Scholars

In comparison to various other materials, Carbon Fiber, specifically Carbon Fiber Reinforced Polymers (CFRP), is pre-eminent amongst other materials for use on aeronautical systems. Due to its high specific strength (strength-to-weight ratio), CFRP is prominent for carrying heavy loads while maintaining a lightweight build. However, when influenced by heat resulting from air resistance, CFRP is known to undergo serious degradation that would significantly decrease the effectiveness of the polymers. To prevent this degradation and maintain the strength of the CFRP, thermal protective layers (TPLs) are designed to shield the CFRP from heat exposure. This research is focused on the examination …

Investigation Of The Low-Temperature Combustion Phenomena Of A Fischer-Tropsch Synthetic Aerospace Fuel In A Constant Volume Combustion Chamber For Greenhouse Gas Reduction, Lily H. Parker

Honors College Theses

Greenhouse gases (GHG) have a harmful effect on our environment as they trap heat in the atmosphere accelerating climate change. As such, the Federal Aviation Administration’s 2025 strategic plan to reduce GHG emissions from air transportation. This call to action for a more environmentally friendly option highlights the importance of synthetic fuels as they are more sustainable compared to traditional fossil fuels. An investigation was conducted into the thermal-physical properties of Synthetic Fischer-Tropsch (F-T) Sustainable Aviation Fuels (SAF) and the Low Temperature Combustion (LTC). LTC is composed of the Low Temperature Heat Release (LTHR) and Negative Temperature Coefficient (NTC) region, …

Experimental And Numerical Investigation Of Lauric Acid Melting At Suboptimal Inclines, Casey J. Troxler

Doctoral Dissertations and Master's Theses

Validation experiments are the baseline for completing numerical studies for engineering design. Applications of the enthalpy-porosity model have expanded in research with the growth of new technologies such as metal additive manufacturing or the renewed interest in thermal energy storage for supplementing renewable energy. A simplified experiment examining the melting behavior of lauric acid from an isothermal surface has become a common case for validating the performance of numerical models. Several studies of this rectangular experiment have been repeatedly used as model validation in a variety of problem conditions.

The first part of this study presents experimental data for the …

Data On The Validation To Determine The Material Thermal Properties Estimation Via A One-Dimensional Transient Convection Model, Lauren B. Tomanek, Daniel S. Stutts

Mechanical and Aerospace Engineering Faculty Research & Creative Works

These data were acquired to estimate the parameters of a closed form solution of a one-dimensional transient convection heat diffusion PDE. The purpose was to demonstrate that the model could be used to determine the thermal conductivity. The system was tested for a wide range of thermal conductivity, 15-400 W/mK, in order to verify that the method was applicable for various materials. The data reported here refer to the study in the research articles, “Material Thermal Properties Estimation Via a One-Dimensional Transient Convection Model” and “Influence of porosity on the thermal, electrical, and mechanical performance of selective laser melted stainless …

Monitoring Of State Transitions In Extreme Environment Application Materials Using Fiber Bragg Grating Sensors, Sabuj Khadka

Electronic Theses and Dissertations

By embedding both a single fiber Bragg grating (FBG) sensor and a thermocouple (TC) during the manufacturing for extreme environment applications of certain classes of materials such as metals and polymers, a novel in-situ approach was developed to precisely monitor their entire manufacturing processes. This novel monitoring technique was able to identify many characteristic points during the curing of room and high-temperature epoxies and the solidification processes of metal alloys composed of tin and bismuth which were selected in this research purely for verification purposes. Some of the characteristic points identified for the epoxies were: (i) the gel point, (ii) …

Jcati Carbon Fiber Recycler: Oven Enclosure, Margarita Romero

All Undergraduate Projects

Central Washington University partners with Boeing and is funded by the Joint Center of Aerospace Technology Innovation (JCATI) to develop a mechanism that takes carbon fiber wing trimmings from Boeing that are resin coated and recycles carbon fiber. This is done by crushing the wing trimmings and then putting it into a 500°C oven to melt off the resin. This project focuses on the enclosure for the oven and making sure precautions are met such as having the outside surface be less than 45c through heat transfer analysis, argon fills enclosure in 13 minutes through fluid dynamics analysis, and 99% …

Experimental And Computational Heat Transfer Study Of Sco2 Single Jet Impingement, John Richardson

Electronic Theses and Dissertations, 2020-2023

The present study experimentally investigates the heat transfer capability of supercritical carbon dioxide (sCO2) single-jet impingement. The evaluated jet Reynolds number range is between 80,000 and 1,000,000, with a non-dimensional jet-to-target surface spacing of 2.8. CO2-impinging jet stagnation conditions were maintained at approximately 20 MPa and a temperature of 673 K for most experiments. The goal is to understand how changes in the aforementioned parameters influence heat transfer between the working fluid and the heated surface. Additionally, due to the elevated Reynolds numbers and difference in thermodynamic properties between air and CO2, air-derived impingement correlations may not be appropriate for …

Building Performance - Societal Drive, Programme And Symposium, Joseph Little, Patrick Daly

Articles

Society is increasingly looking at the construction industry to mitigate the environmental crisis and solve the housing crisis through wholesale embrace of three broad sets of challenges. The MSc in Building Performance (Energy Efficiency in Design) (MSc BP(EED)) was created in 2017 to provide significant upskilling in the knowledge, skills, and software applications of building design professionals so that they can meet these challenges, while creating compliant, sustainable, super-low energy, new and renovated buildings. The delivery of the programme supports upskilling of employed building design professionals at Masters level, encouraging a minority to develop their capacity and interest in research …

Analytical Modeling Of A Novel Elastohydrodynamic Seal Design For Supercritical Co2 Power Cycles, Ikenna C. Ejiogu

College of Graduate Studies: Theses & Dissertations

Supercritical carbon dioxide (sCO₂) power cycles show great potential for higher plant efficiencies and power densities for a wide range of power generation applications such as fossil fuel power plants, nuclear power production, solar power, and geothermal power generation. sCO₂ leakage has been one of the main concerns in such applications, penalizing the cycle efficiencies. The effect of the seal leakage on the cycle efficiency could be as high as 0.65% for a utility sCO₂ power cycle. Therefore, there is a pressing need for effective sealing solutions to get the full benefit of sCO₂ power …

Heat Transfer Characterization Of Carbon Dioxide In Micro Impinging Jet(S) Near Critical Conditions, Stephen Adeoye

Electronic Theses and Dissertations, 2020-2023

The continuous growth and demand of increased operating performances of electronics has brought about an increase in the chip power density posing threat to the thermal management of these devices. Although numerous thermal solutions ranging from passive to active cooling together with a variety of working fluids have been adopted, however, the question whether these available cooling methods could meet up with the ever-growing need for increased operating performances is a concerning one. Jet impingement cooling has been effectively used in many industrial applications due to its high heat transfer capability. The limited study at the micro scale suggests that …

Numerical Study Of Flow Of Supercritical Carbon Dioxide Inside Microchannels With Heat Transfer, Uday Manda

Electronic Theses and Dissertations, 2020-2023

Heat transfer inside microscale geometries is a complex and a challenging phenomenon. As supercritical fluids display large variations in their properties in the vicinity of the critical point, their usage could be more beneficial than traditional coolants. This numerical study, in two parts, primarily focuses on the physics that drives the enhanced heat transfer characteristics of carbon dioxide (CO2) near its critical state and in its supercritical state. In the first part of the study, the flow of supercritical Carbon Dioxide (sCO2) over a heated surface inside a microchannel of hydraulic diameter 0.3 mm was studied using three-dimensional computational fluid …