Heat Transfer, Combustion Commons^™

Thermal Management With Supercritical Carbon Dioxide Under Extreme Applications, Devon Hardy

Doctoral Dissertations and Master's Theses

A unique challenge in thermal system design is minimizing the power required to operate cooling systems while maintaining effective heat removal. Traditional cooling systems utilize single-phase fluids where the heat transfer mechanisms are well understood. To meet a variety of cooling demands, a range of technologies are available, including microchannel forced convection, jet impingement, porous media, nanofluids, pin fin arrays, and film cooling, each offering distinct advantages and limitations. While the performance of single- or two-phase cooling systems are generally predictable, in extreme thermal environments, new cooling solutions are needed to improve overall system efficiency and reliability.

Supercritical fluids, particularly …

Piston Crown Design, Kurt L. Lippmann, Liam T. Janssen, Alex Rangel, Larry J. Davis

Mechanical Engineering

This project investigates the effects of dimpling a piston crown, and its impact on engine combustion dynamics. Through computational methods, the effects of piston crown dimpling on flow characteristics were evaluated. Theoretical results were verified with experimental methods. Experimental methods included characterization of exhaust gas content, engine horsepower and torque, and exhaust opacity.

Development Of On-The-Fly Quasi-Steady State Approximation For Chemical Kinetics In Cfd, Abhinav Balamurugan

Doctoral Dissertations and Master's Theses

This study analyzes the feasibility of On-The-Fly Quasi-Steady-State Approximation (OTF-QSSA) application for solving chemical kinetics within Computational Fluid Dynamics (CFD) simulations, aiming to reduce the computational demand of detailed mechanisms. An algorithm that dynamically identifies and designates Quasi-Steady-State (QSS) species at specific grid locations and instances during the simulation was developed. With this information, our method pseudo-delays the advancement of concentrations for these QSS species—effectively setting their rate of concentration change to zero for a set number iteration before updating using the detailed mechanism and thereby omitting the computationally intensive processes typically required for their calculation during those skipped iteration. …

Applications Of Large Eddy Simulations To Novel Internal Combustion Concepts, Patrick O'Donnell

All Dissertations

Computational fluid dynamics (CFD) simulations of internal combustion engines (ICEs) are becoming an increasingly popular tool in the automotive industry to either explain experimentally observed trends or perform lower cost design iterations. The convenience of commercially available CFD software and advancements made in computing hardware have been the impetus behind this growing popularity. However, obtaining accurate results using these software packages is not a trivial process and requires an in-depth understanding of the underlying numerical methodology and sub models for various physical phenomena. Specific to the ICEs, CFD simulation often entails the use of models for detailed chemistry and combustion, …

Reynolds-Averaged Navier-Stokes Cfd Simulation Of High-Speed Boundary Layers, Michael Tullis

Mechanical Engineering Undergraduate Honors Theses

This paper presents an investigation of Reynolds-averaged Navier-Stokes (RANS) turbulence models used in computational fluid dynamics (CFD) simulations of boundary layer flow and heat transfer in high Mach number flows. This study evaluates an industry standard RANS turbulence model (k-omega SST) and a recently proposed modification to that model (Danis and Durbin [1]), and quantifies the accuracy for predicting high Mach number boundary layer flow. The test cases were previously documented by Duan et al. (2018), who used direct numerical simulation (DNS) to calculate boundary layer flow of an ideal gas over a flat plate at freestream Mach numbers ranging …

A Computational Fluid Dynamic Analysis Of Oxyacetylene Combustion Flow For Use In Material Response Boundary Conditions, Craig Meade

Theses and Dissertations--Mechanical and Aerospace Engineering

Oxyacetylene torches are used in the aerospace industry and research to test thermal protection system materials (TPS) due to their high flame temperatures and high heat flux capabilities. The purpose of this work is to determine a combustion model to accurately simulate the high temperature flow of an oxyacetylene torch. The flow conditions around a sample material can then be used as boundary conditions when modeling TPS material response. Two separate combustion models with equilibrium chemistry were investigated using ANSYS Fluent™; the Eddy-Dissipation Model, and the Partially Premixed model.The results of this study are compared to existing experiments for validation.

Development Of A Quasi-Dimension Gci Combustion Model Aided By Cfd, Jinsu Kim

Graduate Theses, Dissertations, and Problem Reports (ETD)

Advanced combustion strategies have been proposed to improve fuel efficiency while minimizing exhaust emissions. Gasoline compression ignition (GCI) combustion featuring partially premixed compression ignition (PPCI) and diffusion combustion has been recognized as an attractive, viable combustion strategy for its potential and advantages over conventional diesel and gasoline engines. The optimization of the GCI engine system requires the development of a quasi-dimensional GCI combustion model capable of simulating GCI combustion while requesting less computational burden than CFD simulation, which is very critical in engine system simulation. This study developed a quasi-dimension, phenomenological combustion model for PPCI and diffusion combustion to facilitate …

Cfd And Heat Transfer Analysis Of Rocket Cooling Techniques On An Aerospike Nozzle, Geoffrey Sullivan

College of Graduate Studies: Theses & Dissertations

In recent years the development of rocket engines has been mainly focused on improving the engine cycle and creating new fuels. Rocket nozzle design has not been changed since the late 1960s. Recent needs for reliable and reusable rockets, as well as advancements in additive manufacturing, have brought new interest into the aerospike nozzle concept. This nozzle is a type of altitude adjusting nozzle that is up to 90% more efficient than bell nozzles at low altitudes and spends up to 30% less fuel. Since the nozzle body is submerged in the hot exhaust gasses it is difficult to keep …

A Vacuum-Driven Distillation Technology Of Aqueous Solutions And Mixtures, Guo Guangyu

Dissertations

Distillation of aqueous solutions and aqueous mixtures has vast industrial applications, including desalination, wastewater treatment, and fruit juice concentration. Currently, two major distillation technologies are adopted in the industry, membrane separation and thermal distillation. However, both of them face certain inevitable drawbacks. Membrane separation has disadvantages as relying on high-grade energy, requiring membrane, fouling problem, narrow treatment range, limited scalability, and vibrating and noisy operating conditions. Traditional thermal distillation technologies can avoid above concerns but has other shortcomings, such as relatively low energy efficiency and yield rate, complicated and bulky system structure, and scaling problem.

This project proposes an innovative …

Heat Transfer Analysis Of A Data Centre, Arumainathan Kabildev

Student Works (2020-2029)

Data centres are an integral part of networking as it houses servers that facilitate incoming and outgoing data flow. A resolute cooling approach is needed to overcome the hot air dissipated by these servers. This research focused on the computational fluid dynamics (CFD) simulation of the heat transfer modelled upon Telekom Malaysia (TM) City’s data centre 3. The simulation was carried out to ascertain the heat distribution across the data centre by using ANSYS Fluent. The results indicated that the server racks’ inlet temperature reaches 29.79 oC, which is close to the maximum permissible limit according to recommendations provided by …

Development Of Universal Solver For High Enthalpy Flows Through Ablative Materials, Umran Duzel

Theses and Dissertations--Mechanical and Aerospace Engineering

Atmospheric entry occurs at very high speeds which produces high temperature around the vehicle. Entry vehicles are thus equipped with Thermal Protection Systems which are usually made of ablative materials. This dissertation presents a new solver that models the atmospheric entry environment and the thermal protection systems. In this approach, both the external flow and the porous heat shield are solved using the same computational domain. The new solver uses the Volume Averaged Navier-Stokes Equations adapted for hypersonic non-equilibrium flow, and is thus valid for both domains. The code is verified using analytical problems, set of benchmarks and also a …

Adding Semi-Structured Automated Grid Generation And The Menter-Shear Stress Turbulence Transport Model For Internal Combustion Engine Simulations To Novel Fem Lanl Combustion Codes, Brad Montgomery Philipbar

Mechanical Engineering ETDs

The addition of GridPro semi-structured, automated generation of grids for complex moving boundaries for combustion engine applications and the Menter Shear Stress Turbulent Transfer (SST) model are being developed by Los Alamos National Laboratory. The software is called Fast, Easy, Accurate, and Robust Continuum Engineering (FEARCE). In addition to improving the time and effort required to build complex grid geometry for turbulent reactive multi-phase flow in internal combustion engines, the SST turbulence model has been programmed into the Predictor Corrector Fractional-Step (PCS) Finite Element Method (FEM) for reactive flow and turbulent incompressible flow regime validation is performed. The Reynolds-Averaged Navier-Stokes …

Ignition And Extinction Behavior Of Fuels In A Microcombustor, Pawan Sharma

LSU Doctoral Dissertations

Conventional fuel testing device-CFR engine requires large quantities of fuels, which makes it unsuitable for research of small samples of fuels. This current study seeks to address this limitation by using an externally heated microcombustor as an alternative fuel testing device. Mainly three combustion behaviors have been observed inside a microcombustor: strong flames at higher flow rates, Flames with Repetitive Extinction and Ignition (FREI) at intermediate flow rates, and weak flames at marginal flow rates. In previous studies, weak combustion behavior has been proven suitable to study fuel properties from small samples of fuels. Microcombustor experiments typically rely on flame …

Effect Of Aerogel On The Thermal Performance Of Corrugated Composite Sandwich Structures, Jacob Dillon Chess

Master's Theses

Current insulation solutions across multiple industries, especially the commercial sector, can be bulky and ineffective when considering their volume. Aerogels are excellent insulators, exhibiting low thermal conductivities and low densities with a porosity of around 95%. Such characteristics make aerogels effective in decreasing conductive heat transfer within a solid. These requirements are crucial for aerospace and spaceflight applications, where sensitive components exist among extreme temperature environments. When implemented into insulation applications, aerogel can perform better than existing technology while using less material, which limits the amount of volume allocated for insulation. The application of these materials into composites can result …

An Experimental And Computational Study Of Fuel Spray Interaction: Fundamentals And Engine Applications, Le Zhao

Dissertations, Master's Theses and Master's Reports

An efficient spray injection results in better vaporization and air-fuel mixing, leading to combustion stability and reduction of emissions in the internal combustion (IC) engines. The impingement of liquid fuels on chamber wall or piston surface in IC engines is a common phenomenon and fuel film formed in the spray-piston or cylinder wall impingement plays a critical role in engine performance and emissions. Therefore, the study of the spray impingement on the chamber wall or position surface is necessary.

To understand the spray-wall interaction, a single droplet impingement on a solid surface with different conditions was first examined. The droplet-wall …

A Physics-Based Approach To Modeling Wildland Fire Spread Through Porous Fuel Beds, Tingting Tang

Theses and Dissertations--Mechanical and Aerospace Engineering

Wildfires are becoming increasingly erratic nowadays at least in part because of climate change. CFD (computational fluid dynamics)-based models with the potential of simulating extreme behaviors are gaining increasing attention as a means to predict such behavior in order to aid firefighting efforts. This dissertation describes a wildfire model based on the current understanding of wildfire physics. The model includes physics of turbulence, inhomogeneous porous fuel beds, heat release, ignition, and firebrands. A discrete dynamical system for flow in porous media is derived and incorporated into the subgrid-scale model for synthetic-velocity large-eddy simulation (LES), and a general porosity-permeability model is …

Development Of An Evaporation Sub-Model And Simulation Of Multiple Droplet Impingement In Volume Of Fluid Method, Sathya Prasad Potham

Dissertations, Master's Theses and Master's Reports

Droplet collision and impingement on a substrate are widely observed phenomenon in many applications like spray injection of Internal Combustion Engines. Existing Lagrangian models do not provide a comprehensive picture of the outcome of these events and may involve model constants requiring experimental data for validation. Physics based models like Volume of Fluid (VOF) method involve no parametric tuning and are more accurate. The aim of this thesis is to extend the basic VOF method with an evaporation sub-model including an additional vapor phase and implement this model in an open source Computational Fluid Dynamics (CFD) software, OpenFOAM. The new …

Numerical Solver For Multiphase Flows, Victor C B Sousa, Carlo Scalo

The Summer Undergraduate Research Fellowship (SURF) Symposium

The technological development of micro-scale electronic devices is bounded by the challenge of dissipating their heat output. Latent heat absorbed by a fluid during phase transition offers exceptional cooling capabilities while allowing for the design of compact heat exchangers. The understanding of heat transport dynamics in the context of multiphase flow physics is hampered by the limited access to detailed flow features offered by experimental measurements. Computational Fluid Dynamics (CFD) can overcome such difficulties by providing a complete description of the three-dimensional instantaneous flow field. Unfortunately, the majority of the numerical investigations in this field at Purdue are carried out …

High Temperature Flow Solver For Aerothermodynamics Problems, Huaibao Zhang

Theses and Dissertations--Mechanical and Aerospace Engineering

A weakly ionized hypersonic flow solver for the simulation of reentry flow is firstly developed at the University of Kentucky. This code is the fluid dynamics module of known as Kentucky Aerothermodynamics and Thermal Response System (KATS). The solver uses a second-order finite volume approach to solve the laminar Navier– Stokes equations, species mass conservation and energy balance equations for flow in chemical and thermal non-equilibrium state, and a fully implicit first-order backward Euler method for the time integration. The hypersonic flow solver is then extended to account for very low Mach number flow using the preconditioning and switch of …

An Investigation Of Phase-Change Effects During Rapid Compression Machine Experiments, Colin Banyon

Master's Theses (2009 -)

Rapid compression machines (RCMs) are well characterized laboratory scale devices capable of achieving internal combustion (IC) engine relevant thermodynamic environments. These machines are often used to collect ignition delay times as targets for gas-phase chemical kinetic fuel autoigntion models. Modern RCMs utilize creviced piston(s) to improve charge homogeneity and allow for an adequate validation of detailed chemistry mechanisms against experiments using computationally efficient, homogeneous reactor models (HRMs). Conventionally, experiments are preformed by introducing a premixed gas of fuel + oxidizer + diluent into the machine, which is compressed volumetrically via a piston. Experiments investigating low-vapor pressure fuels (e.g. diesels, biodiesels, …

Design And Simulation Of Passive Thermal Management System For Lithium-Ion Battery Packs On An Unmanned Ground Vehicle, Kevin Kenneth Parsons

Master's Theses

The transient thermal response of a 15-cell, 48 volt, lithium-ion battery pack for an unmanned ground vehicle was simulated with ANSYS Fluent. Heat generation rates and specific heat capacity of a single cell were experimentally measured and used as input to the thermal model. A heat generation load was applied to each battery and natural convection film boundary conditions were applied to the exterior of the enclosure. The buoyancy-driven natural convection inside the enclosure was modeled along with the radiation heat transfer between internal components. The maximum temperature of the batteries reached 65.6 °C after 630 seconds of usage …