Heat Transfer, Combustion Commons^™

Global Time-Resolved Measurements Of Inlet/Isolator Unstart Induced By Mass Injection, Andrew N. Bustard, Benjamin L. Bemis, Aaron Marques, Matthew J. Zahr, Thomas J. Juliano

Publications

The inner surface pressure of an axisymmetric inlet/isolator model was measured using anodized-aluminum pressure-sensitive paint (PSP) viewing through cast acrylic. Temperaturesensitive paint was utilized to correct for the PSP’s temperature sensitivity. The model was tested under Mach 5.7 flow at 𝑹𝒆 = 7.1 ×106 /m under conventional noise conditions. Transverse jet injection with jet-to-inlet mass-flow ratios up to 0.8 was used to induce unstart in the inlet/isolator. Background-oriented schlieren visualization of the inlet shocks was collected simultaneously with the PSP to determine when the inlet unstarted. Computational fluid dynamics results were used to determine off-wall flow structures and quantify approach …

Advances In Spacecraft Thermal Control, Sandra K. S. Boetcher, Robert C. Consolo Jr.

Publications

Spacecraft thermal management is critical for ensuring mission success, as it affects the performance and longevity of onboard systems. A comprehensive overview of the state of the art in spacecraft thermal control solutions, as well as a design methodology framework for efficient and effective thermal management, is provided. Various thermal control solutions, including coatings, insulation, heat pipes, phase-change materials, conductive materials, thermal devices, actively pumped fluid loops, and radiators, are discussed along with the primary sources of heat loading in space. The need for accurate modeling and analysis of the thermal environment to identify appropriate thermal control solutions and design …

Comprehensive Review Of Heat Transfer Correlations Of Supercritical Co2 In Straight Tubes Near The Critical Point: A Historical Perspective, Nicholas C. Lopes, Yang Chao, Vinusha Dasarla, Neil P. Sullivan, Mark Ricklick, Sandra Boetcher

Publications

An exhaustive review was undertaken to assemble all available correlations for supercritical CO2 in straight, round tubes of any orientation with special attention paid to how the wildly varying fluid properties near the critical point are handled. The assemblage of correlations, and subsequent discussion, is presented from a historical perspective, starting from pioneering work on the topic in the 1950s to the modern day. Despite the growing sophistication of sCO2 heat transfer correlations, modern correlations are still only generally applicable over a relatively small range of operating conditions, and there has not been a substantial increase in predictive capabilities. Recently, …

Preliminary Study Of Shape-Memory Alloy Torsional Tubes As Thermal Management Actuators Under Non-Ideal Conditions, Paula Sanjuan Espejo, Samuel Desloover, Devon Hardy, Mark Ricklick, Frederick Calkin, David Foutch

Publications

Shape-memory alloys (SMAs) have been used in many engineering applications because of their shape-memory effect and pseudoelasticity. SMA behavior is well understood under steady and constant temperature and loading conditions, whereas transient and non-ideal conditions effects should be further investigated. In this research, SMA torque tubes are studied for use in thermal management applications as self-regulated actuators responding to a process fluid with changes in temperature, with the goal of improved system efficiency by keeping components at an optimal temperature. When utilized in a thermal management configuration, it is likely that the SMA’s thermal environment will be different than that …

Cool Thermal Energy Storage: Water And Ice To Alternative Phase Change Materials, Sandra K. S. Boetcher

Publications

Cool thermal energy storage has a long history dating back to ancient times with modern developments beginning in the mid-nineteenth century where blocks of ice were cut from frozen lakes for cooling applications. Today, the prevalent mode of thermal energy storage is the utilization of ice tanks in commercial buildings for peak shaving and load shifting. In this chapter, a summary of different types of water/ice thermal energy storage systems is provided; an overview of alternative phase change materials for use in cool thermal energy storage is given; and alternative phase change material thermal energy systems, their implementation, challenges, and …

Experimental Study Of Wall Bounded Harbor Seal Whisker Inspired Pin Geometries, Anish Prasad, Mark Ricklick

Publications

Conventional cylindrical/elliptical pins are one of the most widely used geometries in convection cooling systems and are used in the internal cooling of gas turbine blades and other applications, as they promote better heat transfer at the expense of large pressure losses and unsteadiness in the flow. The need to reduce pressure drop and maintain the heat transfer rates are a pressing requirement for a variety of industries to improve their cooling efficiency. One such prominent field of research is conducted in optimizing the design of pin geometries. In this study, a harbor seal whisker inspired geometry is being studied …

Moisture Affinity Of Hdpe/Phase-Change Material Composites For Thermal Energy Storage Applications, Sandra K. Boetcher, Thomas B. Freeman, Rafael M. Rodriguez, Kashif Nawaz

Publications

Moisture adsorption can degrade the structural integrity of thermal energy storage devices and can negatively impact the capacity and charging/discharging behavior. Steady-state and transient experiments are conducted at various operating temperatures to evaluate the moisture affinity of organic phase-change material (PCM) shape stabilized with high-density polyethylene (HDPE).

Thermodynamic Model Of Co2 Deposition In Cold Climates, Sandra K. S. Boetcher, Ted Von Hippel, Matthew J. Traum

Publications

A thermodynamic model, borrowing ideas from psychrometric principles, of a cryogenic direct-air CO2-capture system utilizing a precooler is used to estimate the optimal CO2 removal fraction to minimize energy input per tonne of CO2. Energy costs to operate the system scale almost linearly with the temperature drop between the ingested air and the cryogenic desublimation temperature of CO2, driving siting to the coldest accessible locations. System performance in three Arctic/Antarctic regions where the proposed system can potentially be located is analyzed. Colder ambient temperatures provide colder system input air temperature yielding lower CO2 removal energy requirements. A case is also …

Exergetic Relationship Between The Thermal Properties Of Direct Contact Membrane Distillation, D. Perdue, L. Chen, L. Schaefer

Publications

Direct contact membrane distillation (DCMD) is a process that has shown promise within the field of desalination due to its less energy intensive methods and widespread applications. DCMD is a thermally driven microfiltration separation process that operates on the principle of vapor–liquid equilibrium conditions where heat and mass transfer occur simultaneously. Fundamentally, DCMD is based on a porous hydrophobic membrane separating the hot solution (feed) from the cold solution (permeate) where desalinated water condenses. The membrane interfacial temperatures determine the vapor pressure difference across the membrane. In this work, a direct simulation Monte Carlo analysis is employed to investigate how …

Modelling Of Aerodynamic Process For Coal Waste Dump Located In Geodynamically Dangerous Zone, Elena Vishnevskaya, Alexander Kobylkin, Valeriya Musina, Andrian Batugin, Vladimir Ponomarev, Oksana Vorobyeva

Publications

Previously made evaluations show confinement of fire coal waste dumps to geodynamically dangerous zones which in this work are considered as borders of active blocks of the earth crust. According to the hypothesis under development, when disposing the dumps in geodynamically dangerous zones (GDZ), which have a high penetrating, aerodynamic relation of the dumps with the environment occurs, making the dumps firing possible. Firing of the dumps inflicts environmental, social and material damage. This research is aimed to study possible mechanism of gas mass transfer through GDZ into the body of dump on the base of computer modeling of aerodynamic …

Thermal Removal Of Carbon Dioxide From The Atmosphere: Energy Requirements And Scaling Issues, Ted Von Hippel

Publications

I conduct a systems-level study of direct air capture of CO2 using techniques from thermal physics. This system relies on a combination of an efficient heat exchanger, radiative cooling, and refrigeration, all at industrial scale and operated in environments at low ambient temperatures. While technological developments will be required for such a system to operate efficiently, those developments rest on a long history of refrigeration expertise and technology, and they can be developed and tested at modest scale. I estimate that the energy required to remove CO2 via this approach is comparable to direct air capture by other techniques. The …

Enthalpy-Based System-Model For Pumped Two-Phase Cooling Systems, Leitao Chen, Fanghao Yang, Pritish R. Parida, Mark Schultz, Timothy Chainer

Publications

The development of embedded chip cooling for 2D and 3D integrated circuits using pumped dielectric refrigerant has gained recent attention due to the ability to manage high heat densities and compatibility with electronics. Recent studies have focused on in-situ thermal and hydrodynamic phenomena (e.g. boiling and bubble dynamics) of two-phase flow boiling at micro-scales. In this paper we focus on the two-phase cooling system design including the cooling capability, size and coefficient of performance (COP). In implementing a two-phase cooling, a system-level computational model for two-phase cooling systems becomes necessary. Therefore, a computationally manageable and accurate one dimensional (1D) system …

Heating Element Including Carbon Nanotube (Cnt) Layer, Santhosh Kumar Loganathan, Virginie Rollin, Daewon Kim

Publications

Apparatus , materials , and techniques and techniques herein can include providing a deposited layer comprising a com posite material including carbon nanotubes ( CNTs ) . Accord ing to various examples , the composite can be applied to a substrate such as using a solution containing CNTs and other constituents such as sulfur . The solution can be spray applied to a substrate , or spin - coated upon a substrate , such as to provide a uniform , conductive , and optically - transpar ent film layer . In one application , such a film layer can be …

Natural Convection From Circular Cylinders, Sandra K. S. Boetcher

Publications

Chapter 1

Natural convection heat transfer from circular cylinders in quiescent environments is a subject which has been studied extensively. Although a well-established topic, to the best knowledge of the author no single source of reference is found for natural convection from circular cylinders for varying orientations (horizontal, vertical, and inclined). This book attempts to be a reference for Nusselt number correlations for circular cylinders of all inclinations including horizontal and vertical.

Singular Superposition/Boundary Element Method For Reconstruction Of Multi-Dimensional Heat Flux Distributions With Application To Film Cooling Holes, Mahmood Silieti, Eduardo Divo, Alain J. Kassab

Publications

A hybrid singularity superposition/boundary element-based inverse problem method for the reconstruction of multi-dimensional heat flux distributions is developed. Cauchy conditions are imposed at exposed surfaces that are readily reached for measurements while convective boundary conditions are unknown at surfaces that are not amenable to measurements such as the walls of the cooling holes. The purpose of the inverse analysis is to determine the heat flux distribution along cooling hole surfaces. This is accomplished in an iterative process by distributing a set of singularities (sinks) inside the physical boundaries of the cooling hole (usually along cooling hole centerline) with a given …

Transient Non-Linear Heat Conduction Solution By A Dual Reciprocity Boundary Element Method With An Effective Posteriori Error Estimator, Eduardo Divo, Alain J. Kassab

Publications

A Dual Reciprocity Boundary Element Method is formulated to solve non-linear heat conduction problems. The approach is based on using the Kirchhoff transform along with lagging of the effective non-linear thermal diffusivity. A posteriori error estimate is used to provide effective estimates of the temporal and spatial error. A numerical example is used to demonstrate the approach.