Heat Transfer, Combustion Commons^™

Global Time-Resolved Measurements Of Inlet/Isolator Unstart Induced By Mass Injection, Andrew N. Bustard, Benjamin L. Bemis, Aaron Marques, Matthew J. Zahr, Thomas J. Juliano

Publications

The inner surface pressure of an axisymmetric inlet/isolator model was measured using anodized-aluminum pressure-sensitive paint (PSP) viewing through cast acrylic. Temperaturesensitive paint was utilized to correct for the PSP’s temperature sensitivity. The model was tested under Mach 5.7 flow at 𝑹𝒆 = 7.1 ×106 /m under conventional noise conditions. Transverse jet injection with jet-to-inlet mass-flow ratios up to 0.8 was used to induce unstart in the inlet/isolator. Background-oriented schlieren visualization of the inlet shocks was collected simultaneously with the PSP to determine when the inlet unstarted. Computational fluid dynamics results were used to determine off-wall flow structures and quantify approach …

Multiphysics Transport In Porous Thermal Protection Systems: Experimental Characterization Of Gas Permeability And Radiative Properties, Yejajul Hakim

Theses and Dissertations--Mechanical and Aerospace Engineering

Porous thermal protection systems (TPS) used in hypersonic vehicles exhibit coupled gas and radiative transport across multiple regimes and length scales. Accurate performance prediction requires reliable characterization of permeability, slip-flow behavior, and radiative transport properties, particularly for low-permeability and charred materials where existing data are limited. This dissertation presents experimental methods for characterizing multiphysics transport in porous TPS materials. A modular flow system was developed to measure permeability and slip behavior in both virgin and charred materials under relevant environments. A transient pressure decay method enables accurate permeability estimation in low-permeability regimes and provides insight into effective pore structure. Results …

Breaking The Vapor Barrier And Scale: Revolutionizing Steel Quenching With Ultrasound Technology, Anthony O. Santos

Williams Honors College, Honors Research Projects

The quenching process is a fundamental heat treatment used to enhance material properties by heating steel to its austenitizing temperature and rapidly cooling it to form high-strength martensite. However, this process is often hindered by two surface barriers: the Leidenfrost effect (vapor blanket) and oxide scale. These cooling limitations restrict the use of steel in high-performance aerospace applications due to inconsistent material properties and unpredictable engineering properties. This research investigates the use of fully submersible, 50-watt 40 kHz ultrasound technology to improve cooling rates in a Jominy test [4]. Through numerical simulations and experimental validation, the study demonstrates that acoustic …

Thermal Radiation Effects On Particles From Plasma Arc Radiation, Reece Davis, Joseph Mcgee

Williams Honors College, Honors Research Projects

Understanding the radiation heating and transport of both microparticles and nanoparticles is a phenomenon that is critical for both space and Earth sciences. In space, these particles are heated by plasma arcs within ionized space clouds or solar flares and can be present the path of deep space missions and orbital satellites. While on Earth, processes such as forest fires, nuclear fusion, and microchip manufacturing include the plasma arc heating of particles. These particles lay within the Mie Scattering Regime and Rayleigh Scattering Regime and emit radiation differently based on their diameter. New mathematical and computational modeling has been conducted …

Novel Design And Fabrication Of A High-Speed Transient Heat Flux Sensor For Application To Rotating Detonation Engines, Zachary Todd Tallman

Graduate Theses, Dissertations, and Problem Reports (ETD)

Rotating detonation engine (RDE) combustion systems have been a topic of interest in the pressure gain combustion community for their benefits over traditional gas turbine engine combustors. However, cooling requirements for these engines are significantly higher and less predictable than those of non-detonating engines. To understand and quantify the high-speed heat transfer dynamics within an RDE, a novel high-frequency heat flux sensor is presented. This study aims to design a robust, single-sided sensor that can withstand the high temperature and harsh environment of an RDE for extended durations. Screen printing is used to deposit a layered, platinum-yttria-stabilized zirconia (YSZ) film …

Gas-Generating Reactive Materials: Design, Evaluation And Effect Of Morphology On Their Ignition And Combustion, Purvam Mehulkumar Gandhi

Dissertations

This work investigates optimizing gas-generating reactive materials, focusing on particle morphology's effect on ignition and combustion behavior. Metal-based gas-generating energetic materials (EMs) are promising alternatives to replace traditional CHNO compounds. Design of advanced metal-based EMs requires consistent ways of evaluating how their characteristics affect their ignition and combustion. Many relevant evaluation approaches exist; however, the results may be difficult to compare directly across different studies. Commonly, experimentalists ignite metal-based EMs in enclosed chambers and report pressures, P. However, direct comparison of these pressures is hindered by variations in the chamber volume, V, and the EM mass, m. To standardize the …

Sizing Wind Tunnel Heater For High Enthalpy Conditions, Justin M. Slavick

Master's Theses

This paper determines the feasibility of adding a heater to an existing blowdown supersonic wind tunnel to unlock new high-enthalpy test applications, considering cost and power requirements at a variety of different states. This process includes both modeling the current range of test section properties in Cal Poly's blowdown wind tunnel and determining the new range of properties that a heat exchanger could induce. These results are verified with a computational fluid dynamics study. Additionally, sublimation and ablation properties of materials are explored to create appropriate models to study atmospheric re-entry once the heat exchanger is implemented.

It is found …

High-Fidelity Coupling For Studies Of Ablative Materials At Hypersonic Conditions, Aleksander Zibitsker

Theses and Dissertations--Mechanical and Aerospace Engineering

The development of accurate models and robust numerical tools for simulating ablative thermal protection materials (TPMs) in hypersonic flows is crucial for advancing atmospheric entry and hypersonic technologies. Traditional methods for simulating ablative materials often rely on heavy assumptions, such as equal heat and mass transfer coefficients and chemical equilibrium in the boundary layer, leading to conservative thermal protection system (TPS) designs and insufficient accuracy for certain in-flight ablation phenomena.

This work presents a high-fidelity and versatile coupled framework between hypersonic flow and material response solvers. The flow domain is modeled with an innovative overset CHAMPS NBS-Cart solver, which features …

A Systematic Study Into The Design And Utilization Of Burn Wire As A Means Of Tensioning And Releasing Spacecraft Mechanisms Through Applied Joule Heating, Chandler Dye

Mechanical Engineering Undergraduate Honors Theses

The joule heating characteristics of Nichrome burn wires, often used as a thermal cutting device in mechanisms designed to fasten and release CubeSat deployables, are examined in the following thesis. Wires ranging from 0.125 inches to 2 inches long, and diameters of 30 Ga and 40 Ga, are investigated through analytical calculations and thermal simulations based on heat transfer due to joule heating, and through physical circuitry-based experiments. The temperature data is used to generate heating curves to predict the time it takes for Nichrome wires to fail under varying testing parameters. This research aims to catalog a series of …

Classification Of Electrical Current Used In Electroplastic Forming, Tyler Grimm

All Dissertations

Electrically assisted manufacturing (EAM) is the direct application of an electric current to a workpiece during manufacturing. This advanced manufacturing process has been shown to produce anomalous effects which extend beyond the current state of modeling of thermal influences. These purported non-thermal effects have collectively been termed electroplastic effects (EPEs).

While there is a distinct difference in results between steady-state (ideal DC) testing and pulsed current testing, the very definition of these two EAM methods has not been well established. A "long" pulse may be considered DC current; a "short" pulse may produce electroplastic effects; and even "steady-state" current shapes …

Impact Of Spallation And Internal Radiation On Fibrous Ablative Materials, Raghava Sai Chaitanya Davuluri

Theses and Dissertations--Mechanical and Aerospace Engineering

Space vehicles are equipped with Thermal Protection Systems (TPS) that encounter high heat rates and protect the payload while entering a planetary atmosphere. For most missions that interest NASA, ablative materials are used as TPS. These materials undergo several mass and energy transfer mechanisms to absorb intense heat. The size and construction of the TPS are based on the composition of the planetary atmosphere and the impact of various ablative mechanisms on the flow field and the material. Therefore, it is essential to quantify the rates of different ablative phenomena to model TPS accurately. In this work, the impact of …

Structural Sizing Of Post-Buckled Thermally Stressed Stiffened Panels, Walid Arsalane

Theses and Dissertations

Design of thermoelastic structures can be highly counterintuitive due to design-dependent loading and impact of geometric nonlinearity on the structural response. Thermal loading generates in-plane stresses in a restrained panel, but the presence of geometric nonlinearity creates an extension-bending coupling that results in considerable transverse displacement and variation in stiffness characteristics, and these affects are enhanced in post-bucking regimes. Herein a methodology for structural sizing of thermally stressed post-buckled stiffened panels is proposed and applied for optimization of the blade and hat stiffeners using a gradient-based optimizer. The stiffened panels are subjected to uniform thermal loading and optimized for minimum …

Novel Thermal Coating For High-Speed Airplanes, Abinash Satapathy, Lakshay Battu, Liam Watson, Nazanin Rajabi

Symposium of Student Scholars

In comparison to various other materials, Carbon Fiber, specifically Carbon Fiber Reinforced Polymers (CFRP), is pre-eminent amongst other materials for use on aeronautical systems. Due to its high specific strength (strength-to-weight ratio), CFRP is prominent for carrying heavy loads while maintaining a lightweight build. However, when influenced by heat resulting from air resistance, CFRP is known to undergo serious degradation that would significantly decrease the effectiveness of the polymers. To prevent this degradation and maintain the strength of the CFRP, thermal protective layers (TPLs) are designed to shield the CFRP from heat exposure. This research is focused on the examination …

Jcati Carbon Fiber Recycler: Oven Enclosure, Margarita Romero

All Undergraduate Projects

Central Washington University partners with Boeing and is funded by the Joint Center of Aerospace Technology Innovation (JCATI) to develop a mechanism that takes carbon fiber wing trimmings from Boeing that are resin coated and recycles carbon fiber. This is done by crushing the wing trimmings and then putting it into a 500°C oven to melt off the resin. This project focuses on the enclosure for the oven and making sure precautions are met such as having the outside surface be less than 45c through heat transfer analysis, argon fills enclosure in 13 minutes through fluid dynamics analysis, and 99% …

Numerical Investigation On The Effect Of Spectral Radiative Heat Transfer Within An Ablative Material, Raghava S. C. Davuluri, Rui Fu, Kaveh A. Tagavi, Alexandre Martin

Mechanical Engineering Faculty Publications

The spectral radiative heat flux could impact the material response. In order to evaluate it, a coupling scheme between KATS - MR and P1 approximation model of radiation transfer equation (RTE) is constructed and used. A Band model is developed that divides the spectral domain into small bands of unequal widths. Two verification studies are conducted: one by comparing the simulation computed by the Band model with pure conduction results and the other by comparing with similar models of RTE. The comparative results from the verification studies indicate that the Band model is computationally efficient and can be used to …

Fully Coupled Internal Radiative Heat Transfer For The 3d Material Response Of Heat Shield, Raghava S. C. Davuluri, Rui Fu, Kaveh A. Tagavi, Alexandre Martin

Mechanical Engineering Faculty Publications

The radiative transfer equation (RTE) is strongly coupled to the material response code KATS. A P-1 approximation model of RTE is used to account for radiation heat transfer within the material. First, the verification of the RTE model is performed by comparing the numerical and analytical solutions. Next, the coupling scheme is validated by comparing the temperature profiles of pure conduction and conduction coupled with radiative emission. The validation study is conducted on Marschall et al. cases (radiant heating, arc-jet heating, and space shuttle entry), 3D Block, 2D IsoQ sample, and Stardust Return Capsule. The validation results agree well for …

Review: Factors Affecting Composite Laminates Against Lightning Strikes, Aaryan Manoj Nair

Publications and Research

Lightning strike protection (LSP) have recently been a newly developing field particularly with the emergence of graphene thin film integration into carbon fiber composite structures. This technology has a widespread application in airplanes, wind turbines, and other instruments which are susceptible to frequent lightning strikes. Electrical discharge of the instrument in a safe manner is vital for the safety of the passengers (in the case of flights) as well as the integrity of the aircraft structures because of their specific mechanical and structural properties, which are essential for their functioning. The purpose of the study is to fabricate graphene thin …

Numerical Reconstruction Of Spalled Particle Trajectories In An Arc-Jet Environment, Raghava S. C. Davuluri, Sean C. C. Bailey, Kaveh A. Tagavi, Alexandre Martin

Mechanical Engineering Faculty Publications

To evaluate the effects of spallation on ablative material, it is necessary to evaluate the mass loss. To do so, a Lagrangian particle trajectory code is used to reconstruct trajectories that match the experimental data for all kinematic parameters. The results from spallation experiments conducted at the NASA HYMETS facility over a wedge sample were used. A data-driven adaptive methodology was used to adapts the ejection parameters until the numerical trajectory matches the experimental data. The preliminary reconstruction results show that the size of the particles seemed to be correlated with the location of the ejection event. The size of …

Thermal Modeling Of Additive Manufacturing Using Graph Theory: Validation With Directed Energy Deposition, Jordan Severson

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Metal additive manufacturing (AM/3D printing) offers unparalleled advantages over conventional manufacturing, including greater design freedom and a lower lead time. However, the use of AM parts in safety-critical industries, such as aerospace and biomedical, is limited by the tendency of the process to create flaws that can lead to sudden failure during use. The root cause of flaw formation in metal AM parts, such as porosity and deformation, is linked to the temperature inside the part during the process, called the thermal history. The thermal history is a function of the process parameters and part design.

Consequently, the first step …

Rocket Motor Nozzle, Corey Hillegass

Williams Honors College, Honors Research Projects

For this honors research and senior design project, the authors will research, analyze, and manufacture a rocket motor nozzle for the Akronauts rocket design team. This research and design project will improve how the rocket design team will decide and manufacture nozzles going forward. The impact of this improvement allows the rocket design team to take steps toward being self-sustaining by manufacturing student designed parts as opposed to commercially bought parts. This will not only be successful in increasing student impact on future designs, but also provides a technical challenge for the authors and will present as an impressive feat …

Improving The Delivered Specific Impulse Of Composite Rocket Propellant Through Alteration Of Chemical Composition: Methodology And Parameters For Characterization Of Propellant And Validation Of Simulation Software Common To The Amateur Rocketry Community, Isaac O'Brien, Austin Ryan

Williams Honors College, Honors Research Projects

In this study, two solid composite rocket propellants were designed utilizing ProPEP, a rocket propellant formulation software common in the amateur and hobby rocketry communities. The two propellants were designed to optimize specific impulse relative to a literature propellant designed by 1020 Research Labs. The literature propellant was also tested in order to validate the design of experiment as well as the mixing and testing procedures. All three propellants, which includes the literature propellant RCS-P, and the two novel propellants AKR-P1 and AKR-P2 were characterized with static tests. The results of the static tests provide data on propellant performance and …

Effect Of Aerogel On The Thermal Performance Of Corrugated Composite Sandwich Structures, Jacob Dillon Chess

Master's Theses

Current insulation solutions across multiple industries, especially the commercial sector, can be bulky and ineffective when considering their volume. Aerogels are excellent insulators, exhibiting low thermal conductivities and low densities with a porosity of around 95%. Such characteristics make aerogels effective in decreasing conductive heat transfer within a solid. These requirements are crucial for aerospace and spaceflight applications, where sensitive components exist among extreme temperature environments. When implemented into insulation applications, aerogel can perform better than existing technology while using less material, which limits the amount of volume allocated for insulation. The application of these materials into composites can result …

Suborbital Spaceflight: A Student Team’S Plan To Send A Rocket To Space, Bryce Chanes, William Carpenter, Julio Benavides, Matthew Haslam, Brenda Haven

Aviation / Aeronautics / Aerospace International Research Conference

The Eagle Space Flight Team was created with the goal of becoming the first undergraduate team to design, build, and launch a rocket capable of suborbital spaceflight. In order to achieve this goal, the team will have to design a rocket capable of atmospheric flight at speeds over Mach 5 and launch it on one of the largest amateur rocket motors ever made. Over the next three years, the team will progress towards accomplishing this feat through a series of incremental test flights. Before the space flight, the team will build three sub-scale rockets designed to reach altitudes of 30,000’, …

Heat Transfer Enhancement And Applications Of Femtosecond Laser Processed Metallic Surfaces, Corey M. Kruse

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

In the present work, functionalized 304 stainless steel metallic surfaces were created with the use of a Femtosecond Laser Surface Processing (FLSP) technique. The laser processing technique produces self-organized micro/nanostructures on the surface. The heat transfer performance of various FLSP functionalized surfaces were characterized through pool boiling and Leidenfrost experiments. Enhancement in both the nucleate and film boiling heat transfer were observed through an increase of the critical heat flux and heat transfer coefficient as well as shifts in the Leidenfrost temperature respectively. For both experiments, a polished reference sample was used as a baseline line to compare against the …

Multidimensional Modeling Of Pyrolysis Gas Transport Inside Orthotropic Charring Ablators, Haoyue Weng

Theses and Dissertations--Mechanical and Aerospace Engineering

During hypersonic atmospheric entry, spacecraft are exposed to enormous aerodynamic heat. To prevent the payload from overheating, charring ablative materials are favored to be applied as the heat shield at the exposing surface of the vehicle. Accurate modeling not only prevents mission failures, but also helps reduce cost. Existing models were mostly limited to one-dimensional and discrepancies were shown against measured experiments and flight-data. To help improve the models and analyze the charring ablation problems, a multidimensional material response module is developed, based on a finite volume method framework. The developed computer program is verified through a series of test-cases, …

Thermal Vacuum Integration For Cal Poly's Space Environments Laboratory, Chelsea Barackman, Steven Jackowski

Aerospace Engineering

The purpose of the senior project is to construct a thermal vacuum by utilizing a preexisting vacuum chamber in the Space Environments Lab, and a donated Advanced Thermal Sciences (ATS) chiller. While a thermal vacuum is already available on campus, building one for the Space Environments Lab would grant undergraduates access to the equipment, allowing a much better understanding of testing methods and procedures in use by the aerospace industry. This paper explains the design and analysis of the thermal vacuum (T-VAC) project as well as the operation and procedures required for the ATS chiller and fill/drain tank. The thermal …

Analysis And Testing Of Heat Transfer Through Honeycomb Panels, Daniel D. Nguyen

Aerospace Engineering

This project attempts to simulate accurately the thermal conductivity of honeycomb panels in the normal direction. Due to the large empty space of the honeycomb core, the thermal radiation mode of heat transfer was modeled along with conduction. Using Newton’s Method to solve for a steady state model of heat moving through the honeycomb panel, the theoretical effective thermal conduction of the honeycomb panel was found, ranging from 1.03 to 1.07 Q/m/K for a heat input of 2.5 W to 11.8 W. An experimental model was designed to test the theoretical results, using a cold plate and a heat plate …

Supersonic Combustion And Mixing Characteristics Of Hydrocarbon Fuels In Screamjet Engines, Ahmed A. Taha

Mechanical & Aerospace Engineering Theses & Dissertations

The combustion characteristics of gaseous propane in supersonic airflow using the rearward-facing step that is swept inward from both end sides is studied. The effect of sweeping the step on the flow field features of propane combustion is investigated.

The study of the supersonic combustion of ethylene is carried out using different combustor configurations, different main fuel equivalence ratios, and different pilot fuel equivalence ratios.

The swept step shows the ability to hold the propane flame in the supersonic air stream without extinction. It was found that the side sweeping of the combustor exhibits the high temperature and combustion products …

Studies On Nonequilibrium Phenomena In Supersonic Chemically Reacting Flows, Rajnish Chandrasekhar

Mechanical & Aerospace Engineering Theses & Dissertations

This study deals with a systematic investigation of nonequilibrium processes in supersonic combustion. The two-dimensional, elliptic Navier-Stokes equations are used to investigate supersonic flows with nonequilibrium chemistry and thermodynamics, coupled with radiation, for hydrogen-air systems. The explicit, unsplit MacCormack finite-difference scheme is used to advance the governing equations in time, until convergence is achieved.

For a basic understanding of the flow physics, premixed flows undergoing finite rate chemical reactions are investigated. Results obtained for specific conditions indicate that the radiative interactions vary substantially, depending on reactions involving HO$\sb2$ and NO species, and that this can have a noticeable influence on …