Heat Transfer, Combustion Commons^™

Thermal Heterogeneity And Lithium Plating During Fast Charging Of Lithium-Ion Battery., Ayodeji Avis Adeniran

Electronic Theses and Dissertations

Presently, widespread adoption of electric vehicles (EVs) is hindered by challenges associated with XFC, including heat generation, lithium plating, and accelerated battery degradation. This dissertation addresses these barriers through two coordinated themes—lithium plating and thermal management—spanning four manuscripts that integrate operando diagnostics, physics-based simulation, and module-level design optimization. The first theme seeks a fundamental investigation into the dynamic interplay between temperature heterogeneity and lithium plating during fast charging, a phenomenon that poses significant limitations on the performance of graphite-based anodes. Firstly, a custom operando cell with a sapphire window was designed to enable synchronized MWIR thermography and optical imaging of …

Measurement Of Conduction, Radiation, And Convection Thermal Energy To Assess Baking Performance In Residential Ovens., Sean Simpson

Electronic Theses and Dissertations

Residential ovens are complicated thermal environments capable of delivering convection, conduction, and radiation heat transfer to food. The amount and mode of heat transfer can change based on the design of the oven cavity, cooling systems, and oven cycle algorithms. Studies have shown that the changes in one heat transfer mode can have an impact on the quality of baked goods. The many variables involved make designing residential ovens a time consuming and costly process. The goal of this study is to adapt thermal energy sensing technology to collect energy data from a residential oven and develop correlations to quality …

Experimental Evaluation Of Heat Leak From Anti-Sweat Components Into Fresh Food And Freezer Compartments Of A Household Refrigerator., Delva Felissaint

Electronic Theses and Dissertations

Condensation beads forming on outside surfaces around a refrigerator is an undesirable byproduct driven by the cold temperature exhibited throughout the unit. To combat this issue, anti-sweat components usually in the form of electrical heaters or tubes carrying hot refrigerant, bring heat to the cold surfaces to ensure their temperatures do not drop below the dew point. Some heat produced by the anti-sweat components may transfer to the interior refrigerated compartment. The purpose of this study is to quantify how much heat from the anti-sweat components are entering the fresh food and freezer compartments and what impact that has on …

Development And Applications Of A Sensor For Measurement Of Different Modes Of Heat Transfer On Foods In A Residential Oven., Kervins Petit-Bois

Electronic Theses and Dissertations

Thermal characterization of an oven is an important part of designing an oven. Understanding how changes in cooking algorithm, oven construction, and oven materials affect cooking performance is critical in ensuring that an oven is properly designed. Often temperature data is used to characterize oven behavior, but this neglects the mode of heat transfer used to achieve these temperatures. Several studies have compared the different modes of heat transfer and cooking performance and have shown that cooking performance in radiation dominated modes are different than in convection dominated modes. The goal of this study is to develop a heat flux …

Nucleate Boiling Under Different Gravity Values: Numerical Simulations & Data-Driven Techniques., Sandipan Banerjee

Electronic Theses and Dissertations

Nucleate boiling is important in nuclear applications and cooling applications under earth gravity conditions. Under reduced gravity or microgravity environment, it is significant too, especially in space exploration applications. Although multiple studies have been performed on nucleate boiling, the effect of gravity on nucleate boiling is not well understood. This dissertation primarily deals with numerical simulations of nucleate boiling using an adaptive Moment-of-Fluid (MoF) method for a single vapor bubble (water vapor or Perfluoro-n-hexane) in saturated liquid for different gravity levels. Results concerning the growth rate of the bubble, specifically the departure diameter and departure time have been provided. The …

Fluid Structure Interactions Within A Common Rail Diesel Injector., Russell Prater

Electronic Theses and Dissertations

The internal flow of a high-pressure diesel injector is simulated numerically to investigate the complex transient flow structures and the unsteady forces imparted to the injector needle that result from the asymmetric flow fields developed during operation. The gas-liquid two phase flow is simulated using a mixture model with the cavitation numerically modeled using the Zwart-Gerber-Belamri model. Both the k-ε model and the detached eddy simulation (DES) model are used, and the numerical results are compared. This dissertation looks at the internal flow of a generic injector at different lifts and characterizes the flow parameters at high lift and low …

Experimental Evaluation Of Heat Leak And Convective Heat Transfer In A Household Freezer., Catherine E. Berghuis

Electronic Theses and Dissertations

Heat leak into household refrigerated cabinets is a key driver affecting energy consumption and efficiency of the cooling system. Additionally, knowledge of heat transfer coefficients of internal surfaces is valuable in the development of cabinet and system level performance simulations. Several studies have examined heat leak of refrigeration units using heat flux sensors (HFS); however, no such studies have used heat flux measurements to derive convective heat transfer coefficients of the refrigerated unit walls. The goal of this study is to evaluate the use of HFS to quantify heat leak into a 490-liter freezer and determine the wall convective heat …

Experimental Investigation Of The Manufacture Of Tunable Graphene Oxide Filter Membranes Using Intense Pulse Light, Joshua H Kotter

Electronic Theses and Dissertations

Reduced graphene oxide is a thin, strong, and inexpensive material with a channel and pore structure that make it a promising candidate for a filtration material. Reduced graphene oxide has been produced and tested in the laboratory, but a lack of scalable manufacturing techniques have limited its commercial use.

This thesis has shown that graphene oxide can be rapidly manufactured with an industrially scalable flash reduction process. The flash reduction process uses 0.58 millisecond pulses from a xenon lamp to reduce the graphene oxide film in less than a minute. Results for partially reduced graphene oxide membranes tuned by the …

Process-Property-Microstructure Relationships In Laser-Powder Bed Fusion Of 420 Stainless Steel., Subrata Deb Nath

Electronic Theses and Dissertations

Laser-powder bed fusion (L-PBF) is an additive manufacturing technique for fabricating metal components with complex design and customized features. However, only a limited number of materials have been widely studied using L-PBF. AISI 420 stainless steel, an alloy with a useful combination of high strength, hardness, and corrosion resistance, is an example of one such material where few L-PBF investigations have emerged to date. In this dissertation, L-PBF experiments were conducted using 420 stainless steel powders to understand the effects of chemical composition, particle size distribution and processing parameters on ensuing physical, mechanical and corrosion properties and microstructure in comparison …

Low Temperature Desiccants In Atmospheric Water Generation., Sunil Gupta

Electronic Theses and Dissertations

Surging global water demand as well as changes to weather patterns and over exploitation of natural water sources, such as ground water, has made potable water a critical resource in many parts of the World already – one rapidly heading towards a crisis situation. Desalination has been adopted as a solution – this is however energy intensive and impractical for most of the developing countries - those most in need of water. A renewable source of energy is solar thermal and solar photovoltaic. A plentiful source of water is the humidity in the atmosphere. This research is to push the …

Effect Of Non-Uniform Air-Side Velocity Distribution On Heat Transfer Model Predictions For Microchannel Condenser., Zachary Chapin

Electronic Theses and Dissertations

This is a study of the effects on heat transfer capacity predictions of microchannel condensers when airflow is maldistributed due to the shape of the condenser. The three shapes investigated in this study are flat, U-shape and roll. Each coil was tested in a water calorimeter and those results were compared to the model prediction. The model prediction was calculated using CoilDesigner™ modeling software with standard correlations. Using the uniform airflow assumption, the model over predicted the heat capacity measured in the calorimeter by 5-11% depending on the coil and inlet conditions. The local airflow velocity was measured using a …

Evaluation Of Two-Phase Evaporation Pressure Drop Correlations For Low Refrigerant Mass Flux., Anna Fenko

Electronic Theses and Dissertations

This study was conducted to evaluate three currently popular two-phase pressure drop models for extremely low velocity refrigerant flow through smooth circular evaporators in household refrigeration systems. Experimental data was taken at mass fluxes under 70 kg/m²s for two refrigerants, R134A and R600A, internal diameters of aluminum evaporators ranging from 0.186 to 0.317 inches, U-bend internal radii ranging from 0.342 to 0.750 inches in horizontal and vertical orientations of evaporators. The geometry of the samples closely resembled a commonly used serpentine shape with multiple U-bends experiencing both, up- and down-flow of the refrigerant. Two empirical models, Müller-Steinhagen & …

I. Improved Ice Meltage In Ice Boxes; Ii. Temperature Control In Tents - Winter Phase., Robert Beaman Duggan

Electronic Theses and Dissertations

This thesis consists of two parts: Improved Ice Meltage in Ice Boxes; Temperature Control in Tents - Winter Phase. Improved ice meltage in the Progress refrigerator is discussed in the first part of the thesis. This portion of the work shows that satisfactory refrigerator temperatures and flat ice meltage could not be obtained simultaneously when using V-shaped ice racks, although they could be obtained separately; however, the basket-type chamber offers greater possibilities of obtaining proper temperatures and meltage characteristics. Series of tests are discussed and conclusions drawn from the results. In the second part of the thesis, a method of …