Heat Transfer, Combustion Commons^™

Techno-Economic Analysis Of The Utilization Of Waste-To-Energy In Jakarta Industrial Estate Pulogadung, Wahyu Punjung Pesonagrata, Mohammad Akita Indianto

Journal of Materials Exploration and Findings

Indonesia has a serious waste problem, which ranking second in marine pollution. Due to significant environmental impacts, a solution to overcome the complexity of waste problems is needed. This study took sample on waste management in Jakarta Industrial Estate Pulogadung (JIEP). JIEP is an Industrial area which covers 443 hectares of land in East Jakarta. This study aims to address Indonesia's serious waste problem by exploring the potential utilization of waste in the Jakarta Industrial Estate Pulogadung (JIEP) as Refuse-Derived Fuel (RDF) for a waste-to-energy (WtE) power plant. The proposed method used a steam power plant with RDF as fuel …

Thermal Transient Analysis Of Mahogany Wood Biomass Pyrolysis: The Role Of Zeolite Catalyst Variations On Temperature Distribution, Yusri Yusri, Widya Wijayanti, Mega Nur Sasongko

Journal of Mechanical Engineering Science and Technology (JMEST)

Biomass pyrolysis is a thermochemical process that converts waste into fuel. The use of zeolite catalysts can enhance efficiency by accelerating biomass decomposition. To demonstrate its effect, thermal simulations were conducted using ANSYS Thermal Transient to analyze temperature distribution, reaction rates, and catalyst effectiveness in the pyrolysis process. This study aims to improve thermal efficiency and temperature uniformity by analyzing the effect of 10% and 20% zeolite mixtures on heat distribution and heating rates at input temperatures of 650 K, 750 K, and 850 K, using the 2D axial symmetry method. The simulation was performed under specific boundary conditions: input …

Preliminary Study Of Circular Lithium-Ion Battery Thermal Management System With Intermittent Cooling, Muhammad Luthfi, Leo Van Gunawan, Yudhy Kurniawan, Sabda Ikhwal Rahmatullah, Alfarikh Muhammad Daen

Journal of Mechanical Engineering Science and Technology (JMEST)

The active battery thermal management system is important to maintain the lithium-ion battery temperature within the optimum and safe range. However, current research has not considered the potential for excessive energy consumption due to the continuous operation of a fluid flow source, such as a fan. This research aims to investigate the effect of a novel approach called intermittent cooling on the cooling efficacy and energy consumption of the circular-configuration BTMS. Both transient computational fluid dynamic simulation and experiment were conducted in this work with 30 pieces of 18650 Lithium-Ion batteries positioned in a staggered circular configuration. From the result, …

Experimental Study Of Dimpled Serpentine Reactors For Hydrogen Production Via Methanol Steam Reforming, Mohamed I. Zeid, Mahmoud A. Shouman, Osama Abdelrehim, Ahmed M. Hamed

Mansoura Engineering Journal

Hydrogen is widely regarded as a clean energy carrier, with methanol steam reforming (MSR) emerging as a promising route for portable and on-board applications due to its favorable operating conditions and high hydrogen yield. Reactor geometry plays a decisive role in hydrogen productivity, pressure drop, and energy efficiency, yet the balance among these factors remains insufficiently addressed. In this study, three serpentine aluminum microreactors: a plain serpentine reactor (PSR), a rhombusdimple reactor (RDR), and a hemispherical-dimple reactor (HDR) were fabricated and coated with a copper (II) oxide, zinc oxide, aluminum oxide (CuO/ZnO/Al₂O₃) catalyst to experimentally investigate the effect of dimple …

Numerical Investigation Of Heat Transfer And Aero-Acoustic Response In Deep Cavity Flows Using Urans Simulations, Abdul Hamid Jabado, Ali Hammoud, Bilal El Zohbi, Bilal Taher, Hassan Assoum

BAU Journal - Science and Technology

This paper presents a numerical study to investigate a deep cavity flow, in order to better understand the underlying mechanisms involved in it, such as flow dynamics, heat transfer, and aeroacoustics. A 2-D Unsteady Reynolds Averaged Navier Stokes model (URANS) was implemented using an SST k-ω turbulence closure simulated over a rectangular deep cavity. Previous experimental results were used to validate the numerical results, to confirm the accuracy of the flow field patterns reproduced. Both controlled and uncontrolled cases were analyzed. Heat transfer was also investigated on both configurations, showing the effect of cavity geometry and inlet conditions on heat …

Impact Of Slot Liner Compression On The Total Thermal Resistance Of The Stator-Winding Assembly In Electric Motors, Lindsay Sutherland

The Journal of Purdue Undergraduate Research

The increasing demand for high-performance electric motors, driven by the rapid adoption of electric vehicles, necessitates effective thermal management techniques that improve their safety, efficiency, and reliability. Heat must be transferred from the current-carrying copper windings to the metallic stator body through an electrically insulating material called the slot liner. However, little research has focused on the interactions between the slot liner and the windings. This study examines the impact of slot liner compression on the thermal resistance across the stator-winding assembly considering two common slot liners: Nomex® 410 and Kapton® MT+. A mock stator-winding assembly was developed by stacking …

Design Of A 10-Ton Capacity Solar-Powered Cold Storage At The Cituis Fish Auction Site, Tangerang, Banten, Indonesia, Wardi Wardi, Muhammad Arif Budiyanto

Journal of Materials Exploration and Findings

This study presents the design of a 10-ton capacity solar-powered cold storage system for the Cituis Fish Auction Site (TPI) in Tangerang, Indonesia, as a sustainable solution to support the coastal fisheries sector. The system comprises two temperature zones: an anteroom at 5°C and a freezer room at -30°C, both integrated with a hybrid system utilizing solar panels and batteries. The total power consumption of the cooling system reaches 27.51 kW. The simulation results, obtained using HOMER Pro software, indicate that the hybrid PV system can reduce CO₂ emissions by up to 16,754 kg per year. From an economic …

Cyclic Combustion Pressure Dynamics Of A Diesel Engine Operating On Waste Frying Oil Biodiesel Blends Using Wavelets, Shady Elmozy, Ahmed Khaira Dr., Elshenawy Elshenawy Prof. Dr., Ali Mohamed Dr., Medhat Elkelawy Prof. Dr,

Journal of Engineering Research

This paper investigates the cyclic combustion pressure dynamics of a single-cylinder diesel engine burning waste frying oil biodiesel blends, employing statistical analysis and continuous wavelet transform (CWT) to evaluate combustion stability. Experiments were conducted at a constant engine load (90%) and speed (1500 rpm), with in-cylinder pressure data collected over 400 consecutive cycles for conventional diesel (RD) and biodiesel blends (UB10, UB30, UB50). Results demonstrate that biodiesel blends marginally reduce average peak cylinder pressure (PP) by 0.3–3.8% while lowering PP variability, evidenced by declining coefficients of variation (COV-PP: 1.27–1.48%), attributed to biodiesel’s elevated viscosity promoting consistent fuel-air mixing. Conversely, mean …

Combustion Characteristics And Cycle-To-Cycle Variations In A Diesel Generator Fueled With Used Frying Oil Biodiesel Blends, Shady Elmozy, Ahmad Khira Dr., E. A. El Shenawy Prof. Dr., Medhat Elkelawy Prof. Dr, Eng.

Journal of Engineering Research

This paper investigates the combustion characteristics and cycle-to-cycle variations in a stationary direct-injection diesel generator fueled with biodiesel derived from used frying oil (UFO) blended with conventional diesel. Used frying oil methyl ester (UFOME), referred to as UB100, was produced through a single-step alkali transesterification process and blended with diesel fuel in varying proportions (UB10, UB20, UB30, UB40, and UB50). Experiments were conducted on a single-cylinder, naturally aspirated diesel engine operating at a constant speed of 1500 rpm under five different load conditions: 0%, 25%, 50%, 75%, and 90%. In-cylinder pressure data from 400 consecutive cycles were analyzed to determine …

The Effects Of Geometric Shape And Power-Law Index On The Thermal Activity And Dynamic Behavior Of A Complex Fluid, Houssem Laidoudi

Emirates Journal for Engineering Research

The paper presents numerical results for non-Newtonian fluid confined horizontally between two rings. The outer ring has a circular shape, low temperature and rotates at a constant and uniform speed, while the inner ring has different shapes (circular, square and triangular), is constant and has a high temperature. This study aims to determine the method and the amount of heat transfer between the rings and under the influence of these factors: the rheological coefficient of the fluid, known as the power-law index, thermal buoyancy intensity, the rotation speed of the outer ring and the geometric shape of the inner ring. …

Numerical Investigation Of Heat Transfer And Pressure Drop In A Circular Microchannel Using Sio₂ Nanofluids, Mahmoud G. Abdelfatah, Osama E. Abd-Ellatif, Ahmed A. A. Attia, Abdelrady O. Elnady

Journal of Engineering Research

A numerical investigation was conducted to analyze the flow characteristics and heat transfer performance of a circular microchannel. using water and SiO₂+pure water nanofluids with volume fractions of 0.3%, 0.7%, and 1%. The microchannel was subjected to a constant heat flux of 100W, and the pressure drop, friction factor, and thermal resistance were evaluated for different Reynolds numbers ranging from 250 to 850. The results show that the addition of SiO₂ nanoparticles enhances the thermal performance of the microchannel by reducing the thermal resistance by up to 1.9% compared to pure water. However, the pressure drop increases with higher Np …

Numerical Simulation Of Airflow Properties Of The Naca 6420 Airfoil Using The Transition Rans K-Ε Model, Oluwaseyi O. Alabi, Saidat A. Salisu, Oyeyemi T. Aforolagba -Balogun, Temitope A. Ladigbolu, Ayotunde O. Fasina, Anas Bala

Al-Bahir

This study investigates the airflow properties around the airfoil using numerical simulation, addressing the longstanding challenge of accurately predicting transition phenomena in turbulent flows. The importance of this research lies in its potential to improve the design and performance of airfoils in various engineering applications, such as wind turbines, and aircraft. A custom 2-dimensional airfoil model was created using Airfoil instruments, featuring a 6% maximum curvature, 40% curvature position, and 20% thickness. COMSOL Multiphysics software performed computations at a velocity of over 19 hours, with data analyzed at 60-minute intervals. The Transition turbulent model was employed to simulate the airflow …

A Review Of Performance Assessment Of Solar-Driven Absorption Chillers Incorporated With Energy Storage Systems, A. Khalil, Mohamed Abdelgaied, May Abdelsalam

Journal of Engineering Research

Abstract- This study evaluates the performance of a solar

collector absorption chiller combined with Phase Change Material (PCM) energy storage devices. Solar energy is used for energy-efficient cooling, and PCM storage improves

efficiency by capturing surplus thermal energy during

abundant solar radiation and releasing it when insufficient. The research assesses performance measures like

COP, energy storage capacity, and overall system efficiency.

Review Of Wood Drying Technologies, Mohamed Salah Elmetwaly, Lotfy Hassan Rabie Saker, Mohamed Sameh Salem

Journal of Engineering Research

Abstract- This article provides a comprehensive review of drying optimization in data centers by examining the limitations of drying methods and discussing advances proposed by scientists through whom we can provide a comparison between different drying systems with an emphasis on improving energy efficiency and thermal performance. Wood drying under atmospheric pressure has many advantages, including the ability to dry at lower temperatures (by reducing the likelihood of some drying defects), significantly reduced drying times, color preservation, increased energy efficiency, better control of volatile organic compound emissions, and the ability to dry very large cross sections. Previous studies have achieved …

Endwall Contouring For Lowering The Thermal Load And Augmenting The Turbine Efficiency, Arjun Kozhikkatil Sunil, Tide Porathoor Sunny

Makara Journal of Technology

Endwall contouring having significance in delineating ideal endwalls competent in thermal load depletion is the focus of this study. We have successfully utilized non-axisymmetric contoured endwalls to enhance turbine performance by controlling the secondary flow characteristics in a blade passage through steady-state numerical hydrodynamics. The supreme endwall pattern could lower the gross pressure loss at the design stage and is related to the size of the top-loss location being productively lowered. The selective numerical shape change using multi-objective optimization at the most prominent locations resulted in contoured endwall geometry and a considerable reduction of thermal exchange in the vane passage …

Heat And Mass Transfer Characteristics During Vacuum Drying Of Wood, Mohamed Salah Elmetwaly, Lotfy Hassan Rabie Saker, Mohamed Sameh Salem

Journal of Engineering Research

The properties affecting the characteristics of heat and mass transfer during vacuum drying of wood are studied in this paper. The experimental work is carried out in 0.0365 m³ test rig vacuum dryer. The drying chamber dimensions are 0.5 m long and 0.305 m diameter carbon steel cylinder. This drying chamber is internally coated with epoxy paint, also this chamber is detachable closing caps at both ends meaning welded at one end and bolted at the other end to facilitate loading and unloading of the specimen. Two stainless steel heat exchanger plates with dimensions 0.3 m length, 0.15 m …

Thermal Performance Investigation Of Thermoelectric Cooling System With Various Hot-Side Cooling Methods, Bowo Y. Prasetyo, Parisya P. Rosulindo, Fujen Wang

Makara Journal of Technology

Thermoelectric devices have been widely used in various applications, including cooling and power generation. The potential application of thermoelectric cooling systems has been studied. However, these systems still face challenges in achieving optimal performance compared with other cooling systems. Several factors, including the hot-side cooling method, influence the performance of thermoelectric systems. This study aimed to investigate the effects of different hot-side cooling methods on the thermoelectric performance and thermal behavior of thermoelectric cooling systems. The testing methods involved the combination of the thermoelectric module with five hot-side heat exchangers, including a square heatsink, a round heatsink, a two-pipe heat …

Performance Augmentation Of Single-Slope Solar Distiller Using An Evacuated Tube Solar Collector: Theoretical Study, Eman Mohammed Abuelezz Eng., Yasser El-Samadony Prof., Khaled Khodary Esmaeil Assoc. Prof., Mohamed Elsheshtawy Zayed Dr.

Journal of Engineering Research

In this research, the performance analysis of a solar-powered desalination system incorporating a single slope-slope solar still and an evacuated tube solar collector is theoretically investigated. The system comprises a solar evacuated tube that absorbs solar radiation, transferring heat to saline water. This water then flows into a solar still, where it absorbs solar energy, boosting the evaporation rate. Two solar distillers, namely the conventional solar distiller (Still-I) and solar still integrated with evacuated tube solar collector (Still-II), are simulated and analyzed under identical outdoor conditions in Tanta, Egypt. A comprehensive theoretical model, developed using FORTAN programming, simulates the performance …

Liquid Nitrogen Shrink-Fitting Process, Natalie Harvey

The Journal of Purdue Undergraduate Research

No abstract provided.

Enhancing The Performance Of Conventional Solar Still Using The Nano-Doped Paint (Ndp) Coating, Hagar Alm-Eldin Bastawissi Prof.Dr, Nermin Elgendy Engineer, Ayman R. El-Tohamy

Journal of Engineering Research

Nations are throughout the entire globe continuously confronting the problem of potable water shortage. Recently, it has been thought that using solar energy to desalinate brackish water offers a practical answer to the world's water crises. The output of these stills, is meager, and academics haven't done much to boost it in any way. Solar distillers have been proposed as an efficient method to produce potable water. In recent years, saltwater has produced drinking water by various ways. The efficiency of a solar distiller is significantly influenced by various factors, most important factor of them is the absorber surface. In …

Co-Firing Of Lpg And Diesel Fuels Through An Innovative Double Swirl Burner: Combustion Characteristics And Exhaust Emissions, Eslam O. Mater, Karim M. Soliman, A. Abdulnaim, Ahmed Abdelrazik Emara, Ahmed Salah Elsahy, Hany A. Moneib

Trends in advanced sciences and technology

The current stringent environmental regulations, the depletion of fossil fuels and the emergence of oil biofuels and synthetic gases had motivated combustion scientists to search for alternative technologies that meet efficient burning, flexible use of multiple fuels and conform to a clean environment. In that respect, several developments had emerged including, low swirl combustion for partially premixed mixtures, “Mild” combustion for diffusion flames. The present experimental study introduces a new concept that combines separate admissions of fuel and air with a central recirculation zone following the diffusion combustion mode, partial premixing within a premix chamber resulting in the creation of …

Air Jet Assisted Combustion Of Oil Diffusion Flames: Effects Of Injection Location And Excess Air Factor, Moustafa Ahmed Gamaleldin, Neama Youssef Ramadan, Ahmed Mohamed Abdulnaim, Ahmed Abdelnasser Adam, Ahmed Abdulrazik Emara, Hany Ahmed Moneib

Trends in advanced sciences and technology

This study investigates a novel methodology for a coaxial disc stabilized burner with a central jet oil spray. It introduces multiple air injection jets within the burner gun's exit section, promoting earlier fuel vaporization and rapid fuel-air mixture formation in the premixing zone. This directly contributes to improved overall combustion efficiency and reduced exhaust emissions. The focus lies on identifying the optimal location for the air injection jets (fixed load, constant jet momentum, and angle) within the exiting premixing zone of the burner gun. In-flame measurements are conducted inside a cylindrical combustor at different air injection locations and varying excess …

Heat Transfer Enhancement In Nanofluid Flows Augmented By Magnetic Flux, Kozhikkatil Sunil Arjun, Rakesh Kumar

Makara Journal of Technology

Heat transfer enhancement could be realized using magnetohydrodynamics together with nanofluids specifically in flow micro-convection in a microtube, flow past a vertical porous plate, and square duct flow with discrete heat sources numerically. A critical value for the Rayleigh number, a maximum value for the magnetic field strength, a low Reynolds number, and volume concentrations exists for thermal enhancement to simulate nanofluid flow in a microtube. Heat transfer enhancement is observed with a reduction in the magnetic field strength in a flow past a heated porous vertical plate. Alumina nanofluid subjected to Hartmann number 10 can boost 81% enhancement in …

An Image Processing Technique For Studying The Flame Structure Using Single Shots Of Oh-Plif Diagnostics, Hazem M. Al-Bulqini, El-Shafie B. Zeidan, Farouk M. Okasha, Mohy S. Mansour

Mansoura Engineering Journal

Laser diagnostic techniques have played a crucial role in enhancing our understanding of combustion processes. Among these techniques, Planar Laser-Induced Fluorescence (PLIF) utilizing OH radicals has proven to be a powerful tool for investigating reaction zones, flame curvature, and flame surface density in diverse flame modes including premixed, non-premixed, and partially premixed flames. However, to fully harness the potential of experimental measurements and laser diagnostics in studying combustion processes, a comprehensive grasp of image processing techniques and tools is essential for effectively analyzing captured images and extracting valuable information. In this study, we present a detailed algorithm that facilitates the …

Steady And Transient Study Of Conjugate Heat Transfer In Regenerative Cooled Nozzle, Khaled Bensayah, Khadidja Kamri

Emirates Journal for Engineering Research

The Heat transfer is one of the most serious challenges that exist in a supersonic nozzle flow. The combustion chamber wall and the nozzle are exposed to high-temperature gases during combustion and gas expansion, which can eventually lead to structural failure. This paper reports a computational study of steady and transient conjugate heat transfer in regenerative water cooled nozzle. Numerical computation solved Reynolds-averaged equations based on RSM-Omega turbulence model coupling with solid-phase heat conduction equation and with coolant-phase. The effect of four inlet cooled approach length 0 inch, 6 inch, 12 inch and 18 inch are studied and validated against …

Accomplishments Of Endwall Contouring On Heat Transfer In A Passage Of A Turbine Blade, Kozhikkatil Sunil Arjun, Tide Porathoor Sunny, Narayanan Biju

Makara Journal of Technology

The study explores axisymmetric endwall contouring with emphasis on the design of novel endwalls capable of heat load reduction. Optimizations with parameterization numerically determined by the endwall of flat shape led to the endwall of the contoured shape with substantial depletion of heat transfer in the passage of the vane. Heat transfer attributes for the generated contoured endwalls were analyzed for the exit Reynolds number of 2 × 106 . Endwall three-dimensional contouring resulted in remarkable changes in secondary flow vortices, jet-to-secondary flow interaction, and film cooling effectiveness on the flat endwall. The results pointed out that the axisymmetric convergent …

Solar Chimney Power Plants: A Mini Review, Ahmed Reda, Waseem Salah, Ahmed Suwailem, Shehab Eldin Ahmed, Omar Lasheen, Amira Elkodama, Moustafa R. Shousha, Amr Ismaiel, Anas A. Rahman

Future Engineering Journal

The main investigations of a novel solar thermal application known as SCPP are summarized in this paper. It is a method of producing electricity from solar energy that relies on the fact that air rises when it is heated. An adequate position within a tall chimney can be utilized to position a turbine to turn it, creating an updraft that can be used to generate power. This system's specifications, design, construction, and use are all covered in the paper along with experimental and analytical research related to it. It also emphasizes the development and execution of SCPP programs.

Sculpting Charge In Graphene Through Patterned Strain, Dylan J. Balter, Jenna Smith

The Journal of Purdue Undergraduate Research

No abstract provided.

Prediction Of Temperature Difference Across Thermoacoustic Stack Through Artificial Neural Network Technique, Anas A. Rahman, Xiaoqing Zhang

Future Engineering Journal

This study involved the application of artificial neural network (ANN) as a new approach for thermoacoustic refrigerators to predict the temperature difference across the stack under some operating conditions. One ANN model for a standing wave thermoacoustic refrigerator, had been developed based on the experimental data from other literature. Temperature difference across the stack was chosen as a response to the input parameters, mean pressure and frequency in the proposed ANN model. A multi-layer feed-forward neural network with a back propagation algorithm had been proposed for predicting the temperature difference across the stack of the thermoacoustic refrigerator. This proposed ANN …

Multiphase Energetic Experiments: Application Of Multiple Object Tracking, Sarah Davis Finch

The Journal of Purdue Undergraduate Research

The process of using computer vision for multiple-objects tracking is incredibly complex. Thus, simulated data was created to mimic the complexities of more realistic data. These test cases would isolate a few of the inaccuracies of real data and allow the researchers to determine what factor of said data is the most detrimental to the object-tracking process. Due to the large quantity of factors at play, Cotter’s method was used to analyze the significance of each factor. The number of detections and the number of centroids were the main dependent results that were utilized to analyze the data. The overall …