Heat Transfer, Combustion Commons^™

Experimental Study Of Dimpled Serpentine Reactors For Hydrogen Production Via Methanol Steam Reforming, Mohamed I. Zeid, Mahmoud A. Shouman, Osama Abdelrehim, Ahmed M. Hamed

Mansoura Engineering Journal

Hydrogen is widely regarded as a clean energy carrier, with methanol steam reforming (MSR) emerging as a promising route for portable and on-board applications due to its favorable operating conditions and high hydrogen yield. Reactor geometry plays a decisive role in hydrogen productivity, pressure drop, and energy efficiency, yet the balance among these factors remains insufficiently addressed. In this study, three serpentine aluminum microreactors: a plain serpentine reactor (PSR), a rhombusdimple reactor (RDR), and a hemispherical-dimple reactor (HDR) were fabricated and coated with a copper (II) oxide, zinc oxide, aluminum oxide (CuO/ZnO/Al₂O₃) catalyst to experimentally investigate the effect of dimple …

Large-Scale Experimental Study On The Impact Of Air Cleaning & Ventilation On Indoor Air Quality And Student Illness-Related Absenteeism, Daud Nosham

Dissertations and Doctoral Documents, University of Nebraska-Lincoln, 2023–

This large-scale randomized experimental field study investigated the effect of portable air purifiers (PAPs) on classroom’s air quality and student’s illness related absenteeism. PAPs were installed in 317 classrooms from various school districts located in Eastern Nebraska. The classrooms were randomly assigned into four conditions: three treatment conditions (T1, T2 & T3) and one control condition (device without any filter). T1 was equipped with HEPA filters, T2 added Activated Carbon (AC) layer to HEPA, and T3 further integrated Germicidal Ultraviolet (GUV) alongside HEPA and AC filters. The measured variables were carbon dioxide (CO2), fine particles (PN2.5) and coarse particles (PNcoarse), …

Fire Fossils: Biomineral Infrastructures In Untangling Climates, Tanmayee More

Masters Theses

Diatoms drift, sediments sink, wildfires generate their own weather. Lightning strikes can blast sand into glass, and microscopic organisms do the same in the cold recesses of the ocean. What alchemies and metabolisms catalyze space, time, and energy? What are the thermodynamics of infrastructure in Climate Change?

Places, materials, and beings are afterimages. Through alchemical experiments, and multi-scalar imaging, I develop simulations of wildfires, and their profound, reverberating effects. In this thesis, a glass-meets-landscape experimental process enters these obscured conditions and renders new material relations for the built environment.

Dynamics Of Separated Flows In Diffusers With Vortex Generators, Sandeep Eldho James

Mechanical and Aerospace Engineering Dissertations - Archive

Flow through curved diffusers is complicated due to the possibility of flow separation and secondary flows. Vortex generators (VGs) are a class of passive flow separation control devices used to improve the flow quality in curved diffusers by suppressing flow separation. However, the literature review demands an in-depth investigation on the physical mechanisms related to flow separation control. Thus, this study aims to improve the understanding of the underlying flow physics associated with VG-induced flow separation control in confined flows. The chosen geometry for this study is a well-documented asymmetric diffuser which exhibits a mild flow separation.

The theoretical formulation …

Healthcare Built Environment And The Covid-19 Pandemic, A Mixed-Method Study, Mohammad Saleh Nikooopayan Tak

All Theses

The outbreak of COVID-19 presented an unparalleled risk to public health, leading to urgent scientific efforts in understanding transmission mechanisms and mitigating risks, especially in healthcare settings. This mixed-methods study examines knowledge advancement regarding indoor air quality in healthcare facilities during the pandemic. A systematic literature review of 163 post-COVID studies identifies key research thrusts and 31 recommendations related to building ventilation, air filtration, surface disinfection, and monitoring. Comparison with over 200 pre-pandemic publications reveals both reliance on established infection control principles and unique contributions, such as detecting viral RNA in air and surface samples indicating potential airborne and fomite …

Solar Chimney Power Plants: A Mini Review, Ahmed Reda, Waseem Salah, Ahmed Suwailem, Shehab Eldin Ahmed, Omar Lasheen, Amira Elkodama, Moustafa R. Shousha, Amr Ismaiel, Anas A. Rahman

Future Engineering Journal

The main investigations of a novel solar thermal application known as SCPP are summarized in this paper. It is a method of producing electricity from solar energy that relies on the fact that air rises when it is heated. An adequate position within a tall chimney can be utilized to position a turbine to turn it, creating an updraft that can be used to generate power. This system's specifications, design, construction, and use are all covered in the paper along with experimental and analytical research related to it. It also emphasizes the development and execution of SCPP programs.

Energy Analysis Of Heating, Ventilation, And Air Conditioning Systems, Erica Ferguson

Williams Honors College, Honors Research Projects

This project studied Heating, Ventilation, and Air Conditioning (HVAC) systems for commercial buildings. I completed an energy model Raleigh County Sheriff’s Department in West Virginia. This building’s HVAC has been completed by the consulting engineering firm: Scheeser Buckley Mayfield. I intern at this company, so they allowed me to use their original design as a basis for comparison. Load calculations, utility costs, energy consumption, and carbon footprint were derived from this energy analysis. The energy model compared three systems: variable air volume (VAV) with electric reheat, variable air volume with hydronic reheat, and variable refrigerant volume (VRV). Based on the …

Building Performance - Societal Drive, Programme And Symposium, Joseph Little, Patrick Daly

Articles

Society is increasingly looking at the construction industry to mitigate the environmental crisis and solve the housing crisis through wholesale embrace of three broad sets of challenges. The MSc in Building Performance (Energy Efficiency in Design) (MSc BP(EED)) was created in 2017 to provide significant upskilling in the knowledge, skills, and software applications of building design professionals so that they can meet these challenges, while creating compliant, sustainable, super-low energy, new and renovated buildings. The delivery of the programme supports upskilling of employed building design professionals at Masters level, encouraging a minority to develop their capacity and interest in research …

Desalination For Sustainable Water Production With An Emphasis On Low Pressure Distillation, Jessica Vivian Savage

Doctoral Dissertations and Master's Theses

Freshwater resources depletion is a growing concern. This freshwater scarcity motivates research into seawater desalination as a means for alleviating the stresses on water demands. The primary methods of desalination include filtration and distillation. This paper explores the potential energy savings of vacuum distillation for seawater desalination to reduce the amount of energy needed to achieve phase change.

Depending on the vacuum boiler design, the vaporization mechanism may be boiling, evaporation, or cavitation. There is very little literature on cavitation that involves mass transfer, so cavitation is not developed here. This thesis focuses on standard models for boiling and evaporation …

Enercon Station Vacuum Pump Replacement, Clint Hembree, Jared D'Amico, Connor Moore, Paul Jeffrey Fontenot, Sydnee Castello, J.J. Clements

Senior Design Project For Engineers

This details the progress of the ENERCON pump replacement project as completed by the Kennesaw State University interdisciplinary senior design group. This project is a two-semester capstone effort for the engineering program at Southern Polytechnic School of Engineering, overseen by Dr. McFall during Fall 2020 and Dr. Khalid during Spring 2021 semesters. The 2020-2021 KSU Interdisciplinary Senior Design team was tasked with completing an Engineering Change Package (ECP) for existing vacuum pumps at ENERCON Station. The mechanical, electrical, and civil students worked together, performing evaluations on existing plant systems to ensure the plant could support the new vacuum pumps. By …

Analysis Of Burning Wood In The Transient State And The Application To Structural Design, Roberta Veliz, Kimberly Guzman

Architectural Engineering

Determining the extent of the contribution of exposed timber on compartment fire dynamics in open floor plans is a complex process. Designers traditionally used compartmentalization design methods which create spaces where flashover is likely, given the fuel load and ventilation conditions. However, due to the large geometric dimensions and spread of fuel, fires in open floor plans are more likely to remain as localized or traveling fires. As such, an understanding of not only ignition potential but also flame spread is critical to characterizing the contribution of exposed timber. An integral step in characterizing the potential contribution is through an …

Heat Transfer Analysis Of A Data Centre, Arumainathan Kabildev

Student Works (2020-2029)

Data centres are an integral part of networking as it houses servers that facilitate incoming and outgoing data flow. A resolute cooling approach is needed to overcome the hot air dissipated by these servers. This research focused on the computational fluid dynamics (CFD) simulation of the heat transfer modelled upon Telekom Malaysia (TM) City’s data centre 3. The simulation was carried out to ascertain the heat distribution across the data centre by using ANSYS Fluent. The results indicated that the server racks’ inlet temperature reaches 29.79 oC, which is close to the maximum permissible limit according to recommendations provided by …

Residential Thermal Storage And Cooling, Joao Marcelo Rocha Belmonte, Jacob Anderson, Andrew Clarke, Daphne Forester, Bianca Hardtke, Josh Hartman, Marc D. Compere

Sustainability Conference

No abstract provided.

Electrification Of Domestic Hot Water To Aid The Integration Of Renewable Energy In The California Grid, Alejandro Cervantes

Cal Poly Humboldt theses and projects

Water heating in residential buildings, also known as domestic hot water (DHW), is the third largest use of energy after appliances and space conditioning. About 90% of the residential buildings in the state use natural gas fueled water heaters, 6% use electricity, and a small percent use liquefied petroleum gas (LPG) or solar water heaters. The current energy use associated with residential water heating is small relative to the total amount of energy consumption in the residential building sector, but it is still a contributor of greenhouse gas (GHG) emissions. Improving hot water systems can be beneficial for bill customer …

Thermodynamic Model Of Co2 Deposition In Cold Climates, Sandra K. S. Boetcher, Ted Von Hippel, Matthew J. Traum

Publications

A thermodynamic model, borrowing ideas from psychrometric principles, of a cryogenic direct-air CO2-capture system utilizing a precooler is used to estimate the optimal CO2 removal fraction to minimize energy input per tonne of CO2. Energy costs to operate the system scale almost linearly with the temperature drop between the ingested air and the cryogenic desublimation temperature of CO2, driving siting to the coldest accessible locations. System performance in three Arctic/Antarctic regions where the proposed system can potentially be located is analyzed. Colder ambient temperatures provide colder system input air temperature yielding lower CO2 removal energy requirements. A case is also …

Biomethane Production From Distillery Wastewater, Zachary Christman

Department of Agronomy and Horticulture: Dissertations, Theses, and Student Research

Distillery wastewater treatment is a great ecological problem, for example, India produces 2.7 billion liters of alcohol that results in 40 billion liters of wastewater. However, this material can be seen as a resource since 11 million cubic meters of biogas at 60% methane could be produced in addition to cleaning the water. The distillery has two options of what to do with the biogas. The first is to use the biogas to fuel the distillery making the production plant more energy efficient and removing some of the need to buy natural gas. The other is to upgrade the biogas …

Proposed Delivery And Return Water Temperatures For Dartmouth College Hot Water Network, Storm Mata

ENGS 86 Independent Projects (AB Students)

This study aimed to verify the viability of the planned hot water heating network at Dartmouth, and determine the necessary hot water radiator areas needed to satisfy the empirically-determined heat demand for buildings on campus, using 5 year of steam con- sumption data. In order to verify viability, the pressure and temperature of the delivery steam and return condensate of the current heating network were used to find the amount of heat delivered per pound of steam to campus. The above-mentioned steam consump- tion data were then used to find the max heat demand for the past five years and …

Literature Survey Of Wet-Waste And Hydrothermal Carbonization System: A Comparative Evaluation, Ramat Olaide Yusuf

Dissertations and Theses

This thesis describes the process of Hydrothermal carbonization and a comparative assessment on recent work done on the process using different feedstocks such as Raw Apple (RA), Apple chip pomace (ACP), apple juice pomace (AJP), grape pomace (GP), macadamia nut-shell (MNS), Sewage Sludge (SS), Poultry Litter (PL) and Grape Marc (GM). The data obtained from the literature survey was compared with the data obtained by the CCL team on the SWPS gasifier (HTC of poultry litter) to obtain how carbon conversion efficiency, syngas composition, thermal efficiency, char production rate, gas production rate and energy utilization vary with carbonization process conditions, …

Elevated Temperature Progressive Damage And Failure Of Duplex Stainless Steel, Darren P. Luke

Civil Engineering ETDs

Ductile failure of metals has been the focus of research efforts within academia and industry for many years since it is tremendously important for understanding the failure of structures under extreme loading conditions. However, limited research has been dedicated to elevated temperature ductile failure, which is critical for evaluating catastrophic events such as industrial, structural or shipping vessel fires. A detailed investigation was conducted on the structural response of Duplex Stainless Steel at elevated temperatures. The temperature dependence of elastic modulus, yield strength, ultimate strength, and ductility was measured up to 1000°C and a continuum damage plasticity model was developed. …

Selecting The Most Effective Energy Modeling Tool Based On A Project Requirement, Sodiq Akande

Electronic Theses and Dissertations

Building energy usage can be derived and controlled by performing building energy modeling. BEM can be performed using numerous software tools such as DesignBuilder, OpenStudio, EnergyPlus etc. These modeling tools can be sorted into three different modeling categories: Black-box, Gray-box and White-box. It is important for a modeler to be able to quickly select the proper tool from the proper category to meet the need of the project. To validate the method of categorizing tools, the three models generated using tools from each category and the modeling outputs required were compared. Each model was designed to estimate the amount of …

Determination Of Aqueous Surfactant Solution Surface Tensions With A Surface Tensiometer, Remelisa Esteves, Birce Dikici Ph.D, Matthew Lehman, Qayyum Mazumder, Nonso Onukwuba

Beyond: Undergraduate Research Journal

Surfactant solutions are applicable to engineering systems for cooling equipment for electronics. Surfactants can be added to water to improve heat transfer. An application of using aqueous surfactant solutions can be through microchannel heat sink. Although it is ideal to redesign these systems to reduce heat, it is a costly method. Surfactant solutions at optimal solution concentration can be able to transfer heat quickly and effectively with minimum expense. The surface tension of surfactant solutions is an important parameter for boiling heat transfer and must be taken into consideration. The purpose of this research is to measure surface tension of …

Determination Of Surfactant Solution Viscosities With A Rotational Viscometer, Remelisa Esteves, Nonso Onukwuba, Birce Dikici Ph.D

Beyond: Undergraduate Research Journal

Aqueous surfactant solutions are used in engineering systems for improving boiling heat transfer. The purpose of this research is to determine the viscosities of surfactant solutions and to investigate the effect of composition on viscosity. The results obtained can possibly be used as reference for further study in the effects of surfactant solution viscosities on nucleate boiling. A rotational viscometer was used to determine the viscosities of three surfactant solutions – SLS, EH-14, and SA-9 – of various compositions at room temperature. It was discovered that the viscosities of SLS, EH-14, and SA-9 had a nearly consistent pattern as their …

Sodhana Environmental - Final Design Report, Eric Taylor, Corissa Bellis, Cody Perez, Cameron Zeller

Mechanical Engineering

A fully designed cost-effective, sustainable, toilet for the developing world.

Transient And Quasi-Steady Thermal Behaviour Of A Building Envelope Due To Retrofitted Cavity Wall And Ceiling Insulation, Aimee Byrne, Gerard Byrne, Anna Davies, Anthony Robinson

Articles

Accurate understanding of the thermal behaviour of building components is essential for predicting heat-ing or cooling needs and facilitates the implementation of more successful energy saving strategies and retrofits. This paper focuses on a specific measure commonly introduced through the residential energy efficiency retrofit programmes in Ireland–insulation. Traditionally, assessments of the performance of building envelopes have been based on assumed thermal resistances of the materials involved, labora-tory tests and computer modelling. The aim of the present work is to investigate the in situ thermal behaviour of a case study building and its components under transient and quasi-steady environmental conditions, comparing …

Heat Transfer Correlations For Low Approach Evaporative Cooling Systems In Buildings, Ben Costelloe, Donal Finn

Articles

The experimental performance of an open industrial scale cooling tower, utilising small approach temperature differences (1–3 K), for rejection of heat at the low water temperatures (11–20 °C) typical of chilled ceilings and other sensible air–water heat dissipation systems in buildings, is examined. The study was carried out under temperate maritime climatic conditions (3–18 °C wet-bulb temperature range). Initially a theoretical analysis of the process at typical conditions for this climate was conducted, which indicated that a water to air (L/G) mass flow rate ratio of less than 1.0 was required for effective operation. Consequently for these low L/G ratios, …

Transient Heat Partition Factor For A Sliding Railcar Wheel, T C. Kennedy, C Plengsaard, Robert F. Harder

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

During a wheel slide the frictional heat generated at the contact interface causes intense heating of the adjacent wheel material. If this material exceeds the austenitising temperature and then cools quickly enough, it can transform into martensite, which may ultimately crack and cause wheel failure. A knowledge of the distribution of the heat partitioned into the wheel and the rail and the resulting temperature fields is critical to developing designs to minimize these deleterious effects. A number of theoretical solutions have appeared in the literature to model the thermal aspects of this phenomenon. The objective of this investigation was to …

Quantifying Savings From Improved Boiler Operation, Kevin Carpenter, J. Kelly Kissock

Mechanical and Aerospace Engineering Faculty Publications

On/off operation and excess combustion air reduce boiler energy efficiency. This paper presents methods to quantify energy savings from switching to modulation control mode and reducing excess air in natural gas fired boilers.

The methods include calculation of combustion temperature, calculation of the relationship between internal convection coefficient and gas flow rate, and calculation of overall heat transfer assuming a parallel-flow heat exchanger model. The method for estimating savings from changing from on/off to modulation control accounts for purge and drift losses through the boiler and the improved heat transfer within the boiler due to the reduced combustion gas flow …

Stress And Thermal Analysis Of The Lotec Carrier, Scott Thomas

Honors Capstone Projects and Theses

No abstract provided.

Maine Guide To Energy Efficient Residential Construction : A Manual Of Accepted Practices, State Of Maine Energy Conservation Division

Maine Collection

Maine Guide to Energy Efficient Residential Construction : A Manual of Accepted Practices

State of Maine Energy Conservation Division, Department of Economic and Community Development, 59 State House Station, Augusta, Maine 04333-0059

Second Edition - November, 1997

Contents: Dedication / Acknowledgements / Introduction / Part 1. Summary of Maine's Residential Energy Standards / Part 2. Siting and Initial Design Considerations / Part 3. Important Considerations for the Design Phase / Part 4. Recommended Construction Practices / Appendixes