Heat Transfer, Combustion Commons^™

Global Time-Resolved Measurements Of Inlet/Isolator Unstart Induced By Mass Injection, Andrew N. Bustard, Benjamin L. Bemis, Aaron Marques, Matthew J. Zahr, Thomas J. Juliano

Publications

The inner surface pressure of an axisymmetric inlet/isolator model was measured using anodized-aluminum pressure-sensitive paint (PSP) viewing through cast acrylic. Temperaturesensitive paint was utilized to correct for the PSP’s temperature sensitivity. The model was tested under Mach 5.7 flow at 𝑹𝒆 = 7.1 ×106 /m under conventional noise conditions. Transverse jet injection with jet-to-inlet mass-flow ratios up to 0.8 was used to induce unstart in the inlet/isolator. Background-oriented schlieren visualization of the inlet shocks was collected simultaneously with the PSP to determine when the inlet unstarted. Computational fluid dynamics results were used to determine off-wall flow structures and quantify approach …

Simulation Study On Nh3 Combustion And NoX Emissions Under Gas Turbine-Relevant Conditions, Kumeesha Arumawadu, Braxton Wiggins, Ziyu Wang

Mechanical and Aerospace Engineering Student Publications and Presentations

Ammonia (NH₃) is a zero-carbon fuel and an attractive hydrogen (H₂) carrier for gas turbine power generation due to its high energy density, ease of storage, and transportation. This study numerically investigates NH₃/air combustion using a hybrid Well-Stirred Reactor (WSR) and Plug Flow Reactor (PFR) model in Cantera at pressures of 1–20 atm, temperatures of 1850–2150 K, and equivalence ratios (ϕ) of 0.7–1.2. The effects of pressure, equivalence ratio, and temperature on NH₃ conversion and NO formation are examined. Results show that NH₃ exhibits a non-monotonic conversion curve with pressure after the …

The Efficacy Of Hybrid Manufacturing For High Stress Automotive Components, Logan Trimmer

Harrisburg University Other Works

The goal of this research was to establish the viability of using hybrid manufacturing for automotive applications. By verifying that high-stress components can be created, it can be assumed that any other lower stress part could be made to match the strength requirements. A limiting factor of adoption for hybrid manufacturing is how new the technology is. Studies on time and cost were performed allowing for comparisons with traditional manufacturing technologies (casting, forging, milling) used in automotive applications. This research utilized a Haas Automation UMC750 5-axis CNC mill with a Meltio laser wire direct energy deposition attachment. Fusion 360 was …

Investigation Of The Flow Field Morphology Of Film Cooling In Supersonic Flow, Umberto Sandri, Massimiliano Ferro, Alessio Picchi, Antonio Andreini, Bruno Facchini, Marc D. Polanka

Faculty Publications

Film cooling is widely implemented in highly thermally stressed gas turbine components. Its performance has been extensively investigated for several decades and many results are available in the literature. In conventional gas turbines, regions of supersonic flow are not prevalent and should generally be avoided. For this reason, results relative to film cooling in supersonic flow are limited. Nevertheless, a new interest related to Rotating Detonation Combustors (RDC) and supersonic turbines is growing. The implementation of those engine components in a gas turbine is likely to need film cooling for thermal protection. In this context, it becomes crucial to gain …

Residential Hvac Installation Faults: Field Prevalence, Drivers, And Energy Impacts, Seyed Ali Rooholghodos

Dissertations and Doctoral Documents, University of Nebraska-Lincoln, 2023–

Faults in residential comfort systems can have detrimental effects on the performance of the system, reducing the energy efficiency, affecting indoor comfort, and shortening equipment lifespan. Many of the faults occur at installation. However, there has not previously been a systematic and nationally representative study to indicate the prevalence of the faults, meaning the distribution of faults by fault type and fault intensity. Understanding true fault prevalence is essential to be able to identify derivers, and to assess the incremental electricity consumption of the new installation systems.

This study presents on-site data from 341 new central cooling systems—air conditioners and …

Large-Scale Experimental Study On The Impact Of Air Cleaning & Ventilation On Indoor Air Quality And Student Illness-Related Absenteeism, Daud Nosham

Dissertations and Doctoral Documents, University of Nebraska-Lincoln, 2023–

This large-scale randomized experimental field study investigated the effect of portable air purifiers (PAPs) on classroom’s air quality and student’s illness related absenteeism. PAPs were installed in 317 classrooms from various school districts located in Eastern Nebraska. The classrooms were randomly assigned into four conditions: three treatment conditions (T1, T2 & T3) and one control condition (device without any filter). T1 was equipped with HEPA filters, T2 added Activated Carbon (AC) layer to HEPA, and T3 further integrated Germicidal Ultraviolet (GUV) alongside HEPA and AC filters. The measured variables were carbon dioxide (CO2), fine particles (PN2.5) and coarse particles (PNcoarse), …

Optimizing Material Selection And Operational Conditions For Xhv Systems: Lessons From Aisi 1020 And 316l Comparative Studies, Aiman H. Al-Allaq, Md Abdullah Mamun, Matt Poelker, Abdelmageed Elmustafa

Mechanical & Aerospace Engineering Faculty Publications

In this study, AISI 1020 low-carbon steel was investigated as a cost-effective alternative to SS316L stainless steel for reaching extreme high vacuum (XHV) conditions. After being baked at 400°C, a vacuum chamber made of low-carbon steel material exhibited an outgassing rate approximately 2000 times smaller than a similar chamber made of stainless steel. Its activation energy for hydrogen diffusion (27 kJ/mol) is less than half that of stainless steel (60.3 kJ/mol), indicating more efficient hydrogen removal during bakeout. MolFlow+ simulations supported the experimental data and demonstrated the importance of system geometry optimization and minimizing stainless steel content for achieving optimal …

Thermal Management For Optimal Performance Of Polymer Electrolyte Membrane Unitized Regenerative Fuel Cells, Mythy Tran, Ayodeji Demuren

Mechanical & Aerospace Engineering Faculty Publications

Hydrogen is an excellent carrier for energy storage and can be produced from various green and renewable sources. However, the cost of producing hydrogen and converting it to useful energy is much higher than fossil fuel and traditional energy generation and storage systems. Unitized regenerative fuel cells (URFC) maximize utilization of high-cost cells and their components, thus, lowering system capital cost. Improving the URFC efficiency is an effective way to lower its operating cost. This study evaluates utilization of waste heat during operation and recovery strategy to improve system efficiency of Proton Exchange Membrane (PEM) URFC. A COMSOL Multiphysics 3-D …

A Novel Intelligent Thermal Feedback Framework For Electric Motor Protection In Embedded Robotic Systems, Mohamed Shili, Salah Hammedi, Hicham Chaoui, Khaled Nouri

Electrical & Computer Engineering Faculty Publications

As robotic systems advance in autonomy and sophistication while being used in uncertain environments, the challenge of building reliable and robust electric motors that are embedded into robotic systems has never been a more important engineering problem. Thermal distress caused by extended operation or excessive loading can negatively affect a motor’s performance and efficiency and lead to catastrophic hardware failure. This paper proposes a novel intelligent control framework that includes real-time thermal feedback for hybrid electric motors that are embedded into robotic systems. The framework relies on adaptive control techniques and lightweight machine learning techniques to estimate internal motor temperatures …

Advances In Battery Modeling And Management Systems: A Comprehensive Review Of Techniques, Challenges, And Future Perspectives, Seyed Saeed Madani, Yasmin Shabeer, Ananthu Shibu Nair, Michael Fowler, Satyam Panchal, Carlos Ziebert, Hicham Chaoui, Shi Xue Dou, Khay See, Saad Mekhilef, Françios Allard

Electrical & Computer Engineering Faculty Publications

Energy storage systems (ESSs) and electric vehicle (EV) batteries depend on battery management systems (BMSs) for their longevity, safety, and effectiveness. Battery modeling is crucial to the operation of BMSs, as it enhances temperature control, fault detection, and state estimation, thereby maximizing efficiency and preventing malfunctions. This paper thoroughly examines the most recent advancements in battery and BMS modeling, including data-driven, thermal, and electrochemical methods. Advanced modeling approaches are explored, including physics-based models that incorporate mechanical stress and aging effects, as well as artificial intelligence (AI)-driven state estimation. New technologies that facilitate data-driven decision-making, real-time monitoring, and simplified systems include …

Investigation Of Conductive Die-Top Thermal Capacitors During Short Circuit Operation Of Silicon Carbide Devices, Youssef Abotaleb

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Silicon carbide (SiC) power devices have garnered significant attention in recent years due to their superior thermal and electrical properties compared to traditional silicon devices. However, SiC power devices suffer from severe reliability issues arising from their mechanical properties. This is because the Young's modulus of SiC is about three times larger than that of silicon, which correspondingly raises the mechanical stresses acting on the bonding structure, often leading to device failure under power shock events.

Traditional packaging materials and designs tend to constrain SiC performance, as hot-spot temperature resulting from a power shock is one of the key factors …

Performance-Tunable Thermal Barrier Coating For Carbon Fiber-Reinforced Plastic Composites Via Flame Spraying, Heejin Kim, Kandasamy Praveen, Min Wook Lee, Juhyeong Lee

Mechanical and Aerospace Engineering Faculty Publications

Thermal barrier coatings (TBCs) are essential for improving the heat resistance of materials operating in high-temperature environments. This paper proposes a new method for manufacturing double-layered TBC with graded porosity for carbon fiber-reinforced plastic (CFRP) composites. The TBC was created by a flame spraying process, consisting of relatively dense and porous layers: (1) a dense layer was produced by spraying yttria-stabilized zirconia (YSZ) particles directly onto neat carbon fabric substrate and (2) a porous layer was prepared by co-spraying YSZ particles with sacrificial polyetheretherketone (PEEK) particles. The porosity of the porous layer was controlled by varying a PEEK injection distance …

Enhancing Crossflow Dynamics Through The Gas Injection From Multiple Cylinders, Sahrish B. Naqvi, Sadia Siddiqa, Maciej Matyka, Rama S. R. Gorla, Md. Mamum Molla

Faculty Publications

We investigate unsteady, two-dimensional laminar fluid flow around cylinders, focusing on understanding the impact of injecting methane gas through two diametrically opposite arcs on the cylinder in the crossflow of the second fluid. This study encompasses applications in mixing and dispersion, which are crucial in various technological and natural processes. Our analysis addresses velocity field’s contribution to the spatiotemporal distribution of transported quantities. We observed that mixing induces a transition from laminar to turbulent flow. Depending on the injected-to-crossflow velocity ratios, the wake vortices downstream of cylinder arrays separate from or connect to the injected gas. This phenomenon significantly impacts …

Effects Of Fluid Slip On Heat Transfer In The Thin Film Region In A Microchannel, Rama S. R. Gorla, John Brewer, Abdeel Roman

Faculty Publications

A theoretical study was undertaken to investigate the influence of interfacial slip on evaporation of a thin liquid film in a microfluidic channel. The disjoining pressure and the capillary force which drive the liquid flow at the liquid-vapor interface in thin film region are adopted. The evaporating thin film region is an extended meniscus beyond the apparent contact line at a liquid/solid interface. Thin film evaporation plays a key role in a highly efficient heat pipe. Slip length was found to affect the heat transfer in the microchannel by altering the thin film geometry.

Investigating Near-Field Radiative Heat Transfer With Titanium Carbide Mxenes And Slanted Columnar Thin Films, Sean Luke Murray

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

This work investigates the mechanisms to manipulate and control the magnitudes of Near-Field Radiative Heat Transfer (NFRHT) using two-dimensional materials and nanostructured surfaces. NFRHT occurs when the geometrical features of the radiating objects or the separation distance between interacting bodies are comparable to or lower than the characteristic thermal radiation wavelength. NFRHT magnitudes surpass the blackbody limit by several orders of magnitude due to phenomena such as photon tunneling and new modes of energy transfer, like surface polaritons. Therefore, it is crucial to understand how material properties and surface nanostructures affect NFRHT.

The first part of this work examines the …

Ultrashort Pulsed Laser Treatment Is Effective At Sterilizing Metal Surfaces For Planetary Protection, Kaleb Mcquillan

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

To prevent forward contamination from microbes aboard spacecraft intended for exploration of solar system bodies there is a need for effective sterilization methods. However, current techniques are both time-consuming and expensive. For example, dry heat sterilization requires removal from the assembly site and several days of treatment. Furthermore, some components such as optics and electronics are not compatible with current sterilization techniques. In this thesis, a novel femtosecond laser surface processing technique for the rapid sterilization of spacecraft hardware is reported. Femtosecond lasers produce extremely high photon fluxes (10²⁹ photons/s*cm², ~0.03 J/cm²) in extremely short …

Experimental Study On The Effect Of Micro Concentrations Of Hybrid Nanofluids Through Microchannel Heat Sinks, Mohamed Salaheldin Elsherbiny, Moustafa Ali, Moatsem Shahin, Mahmoud El-Kady

Renewable Mechanical Energy

The current study examines the convective heat transfer coefficient experimentally. It assesses the performance of Al2O3, CuO, ZnO, and Ag/ distilled water nanofluids up to a tetra level of hybridization utilized in microprocessor cooling systems equipped with MCHS. An equal ratio of 50%, 33.3%, and 25% for di-, tri-, and tetra-nanofluids, respectively, with a focus on micro-volume fraction 0.025% and comparing it with 0.05%. Operating conditions were as follows: heat loading from 136.4 up to 196.4 watts; and flow rate from 0.35 up to 0.5 LPM. The findings showed that all types of mono nanofluids showed an increase in Nu …

Turbine Cooling System With Energy Separation, James L. Rutledge, Matthew N. Fuqua, Carol M. Bryant

AFIT Patents

A method and system for cooling an engine and/or vehicle using energy separation is disclosed herein. An energy separation device is operable for separating a compressed gaseous coolant stream into a first relatively cooler coolant flow stream and a second relatively hotter coolant flow stream. The relative cooler coolant flow stream is directed to a first region requiring increased cooling and the relative hotter coolant flow stream is directed to a second region requiring lower cooling than the first region in the engine or vehicle.

Mechanical Engineering Capstone: A Reflection On The Design And Prototyping Of A Portable Water Heating System, Timothy Goldsmith

Honors Program: Senior Projects (Public)

This thesis includes several documents from a Mechanical Engineering Capstone course. These include project postmortem reports written at the conclusion of each term. These reports summarize the designing and prototyping of a portable water heating system. Additionally, this thesis includes written feedback on the final presentations for six other senior design teams. In these documents, presentations and projects are evaluated and encouragement and feedback are provided for the teams. The final component of this thesis is an essay reflecting on the different leadership roles assumed during the capstone course.

Measuring Soot In A Novel Configuration For Diffusion Flames Fueled By Ethylene Doped With Iso-Dodecane, Christian Bjork

Honors Scholar Theses

Sustainable Aviation Fuels (SAFs) are seen as the path forward for decarbonizing hard-to-electrify sectors. Using SAFs over traditional fossil fuels abates carbon dioxide emissions but still may present soot emission problems. A milestone in the abatement of soot would be understating its formation mechanisms.

This study aims to quantify soot products resulting from an ethylene flame doped with iso-dodecane, a surrogate SAF component. The burner selected for the investigation is the novel Planar Mixing Layer Flame (PMLF) which allows the tracking of soot formation with the height above the burner (HAB) in a stable diffusion flame. A baseline ethylene-fueled flame …

Radiative Cooling For Energy-Efficient Power Generation, Rickia Hanna

Celebrating Scholarship and Creativity Day (2018-)

This thesis examined radiative cooling on a small scale using a hybrid photovoltaic/radiative cooling model system, to determine its efficiency for large-scale power generation. Radiative cooling is concerned with heat transfer and this thesis’s main goal is to harness that heat energy to produce electricity. The efficiency of the system was tested using various light sources at different angles and total power output. The testing was done several times and there proved to be a proportional relationship between light intensity and current output. However, due to the performance threshold of the PTEC module, the component of the system used to …

A Novel Computational Analysis Of Boundary-Driven Two-Dimensional Heat Flow With Internal Heat Generation, Muhammad Abid, Madiha Bibi, Nasir Yasin, Muhammad Shahid

Mathematics & Statistics Faculty Publications

Accurate numerical solution of parabolic and elliptic partial differential equations governing two-dimensional heat transfer is critical for engineering simulations but computationally challenging. This work employs key numerical techniques finite differences, conjugate gradients, and Crank-Nicolson time stepping to solve the heat diffusion equation and analyze method performance. The Poisson equation is discretized using second-order central finite differences and solved with the conjugate gradient approach to determine the steady state solution. The transient heat equation is integrated in time via the Crank-Nicolson implicit scheme, also utilizing conjugate gradients. The methods effectively compute solutions matching analytical and boundary conditions. Convergence and stability are …

A Project-Based Learning Activity For An Engineering Technology Heat Transfer Course To Design A Shell-And-Tube Heat Exchanger, Nathan Luetke, Orlando Ayala

Engineering Technology Faculty Publications

Thermofluids courses demand a strong grasp of mathematics and employ physics extensively to describe physical systems. Heat transfer, in particular, presents challenging topics, which can be even more daunting for engineering technology students. In this paper, we present the implementation of a project-based learning activity in the engineering technology heat transfer course. The students' task involves designing a shell-and-tube heat exchanger to meet specific minimum requirements. The objective is to provide students with a real-world assignment that enhances their heat transfer calculation skills. To accommodate instructors' busy schedules, we have developed an assignment that is user friendly. Detailed instructor guides …

A Review Of Nano And Microscale Heat Transfer: An Experimental And Molecular Dynamics Perspective, Samyabrata Chatterjee, Paras, Han Hu, Monojit Chakraborty

Mechanical Engineering Faculty Publications and Presentations

Significant progress in the development of micro and nanoscale devices has been observed for the past three decades. The thermal transportation in these small-length scales varies significantly, and it is difficult to explain the underlying physics using the pre-existing theoretical formulations. When the bulk dimension of a system is comparable to or smaller than the mean free path (MFP) of the thermal carriers, classical theories, such as Fourier’s Law of heat conduction, are unable to accurately explain the system energy dynamics. The phenomena of energy transit and conversion at the micro to nanoscale is an interesting topic of research due …

Advances In Spacecraft Thermal Control, Sandra K. S. Boetcher, Robert C. Consolo Jr.

Publications

Spacecraft thermal management is critical for ensuring mission success, as it affects the performance and longevity of onboard systems. A comprehensive overview of the state of the art in spacecraft thermal control solutions, as well as a design methodology framework for efficient and effective thermal management, is provided. Various thermal control solutions, including coatings, insulation, heat pipes, phase-change materials, conductive materials, thermal devices, actively pumped fluid loops, and radiators, are discussed along with the primary sources of heat loading in space. The need for accurate modeling and analysis of the thermal environment to identify appropriate thermal control solutions and design …

Addressing Low Heat Pump Heating System Sales In The Uk, Ben Costelloe

Articles

The replacement of existing fossil fuel boilers with heat pumps is seen as a key measure in the decarbonisation of heating systems and addressing climate change. This policy however, is currently failing in many Western European states, particularly in the UK. The many reasons for this situation are examined. However, the age of UK housing stock and particularly the high number of dwellings built prior to the introduction of building insulation regulations in 1980, are key. To maintain the running cost of air source heat pumps competitive with those of the gas boilers they generally replace the heat pump lift …

Thermal Transport And Physical Characteristics Of Silver-Reinforced Biodegradable Nanolubricant, Jaime Taha-Tijerina, Karla Aviña, Nicolás Antonio Ulloa-Castillo, Dulce Viridiana Melo-Maximo

Informatics and Engineering Systems Faculty Publications

In this investigation, the thermal transport behavior of biodegradable lubricant reinforced with silver nanostructures (AgNs) at various filler fractions of 0.01, 0.05, 0.10, and 0.20 weight percent was evaluated over a temperature scan analysis, ranging from room temperature up to 60 °C. The experimental results revealed significant gradual enhancements in thermal conductivity as AgNs concentration and evaluating temperatures were increased. These improvements showed the important role of nanostructures’ interaction within the biodegradable lubricant. The thermal conductivity performance improved for nanolubricants ranging from 6.5% at 30 °C and 0.20 wt.% AgNs content up to a maximum 32.2%, which was obtained at …

Pla-S-Tech: Pla Sustainable Technology, Sean Sapper, Ryan Decarlo, Elle Whitney, Samantha Dombrowski, Dalton Prokop, Dominic Zaio, Tyler Stokes, David Deese, Blake Hengel, Yi Guo

Mechanical and Civil Engineering Student Publications

To recycle waste material produced by fused deposition modeling (FDM) 3D printers, a recycler was designed and manufactured to convert plastic scraps into usable filament. The device does so by breaking down plastic material to a uniform size with the shredder, melting and compressing these pieces into a cylindrical strand with the extruder, and wrapping this strand around a filament spool with the spooler. As the device is mostly made from commercially-available components, it is easily maintainable and user-serviceable, while also costing less than similar devices on the market.

Precise And Analytical Calculation Of Interface Surface Area In Sharp Interfaces And Multiphase Modeling, Simon P. Shipkowski, Isaac Bernabe Perez Raya

Articles

Various kinds of Piecewise Linear Interface Calculations (PLIC) are commonly used in Computational Fluid Dynamics (CFD) for multiphase flows. Here, a new method is proposed to calculate the interface size for CFD simulations. This PLIC method with the modifier, Analytic Size Based [method], (PLIC-ASB), being that the calculation requires a symbolic equation and no approximation or numerical methods. The primary advantage of the PLIC-ASB is maintaining a sharp interface and providing for physics-based (not iterative or empirically derived factors) mass transfer due to the cell-by-cell accuracy. Along with the sharp interface, this method leads to precise interface displacements and suppresses …

Investigation Of Fiber Orientation And Mechanical Properties Of Pyrolysis Recycled Carbon-Fiber Reinforced Thermoset Composite, Reva N. Simmons, Harry Lee, Garam Kim

Discovery Undergraduate Interdisciplinary Research Internship

With increasing demand of carbon fiber reinforced fiber thermoset composites, establishing a sustainable cycle for these materials becomes crucial. Pyrolysis is a process of reclaiming carbon fiber from thermoset composites by thermally degrading the polymer at high temperatures allowing the fibers to be extracted. Carbon fiber reclaimed through current pyrolysis processes for thermoset composites typically loses its original shape and orientation, making it difficult to reorganize the fibers. This study investigated the feasibility of maintaining the fiber orientations for continuous fiber reinforced thermoset composite during pyrolysis by stitching the carbon fiber layup to a conformable copper mesh during the manufacturing …