Heat Transfer, Combustion Commons^™

Thermal Management With Supercritical Carbon Dioxide Under Extreme Applications, Devon Hardy

Doctoral Dissertations and Master's Theses

A unique challenge in thermal system design is minimizing the power required to operate cooling systems while maintaining effective heat removal. Traditional cooling systems utilize single-phase fluids where the heat transfer mechanisms are well understood. To meet a variety of cooling demands, a range of technologies are available, including microchannel forced convection, jet impingement, porous media, nanofluids, pin fin arrays, and film cooling, each offering distinct advantages and limitations. While the performance of single- or two-phase cooling systems are generally predictable, in extreme thermal environments, new cooling solutions are needed to improve overall system efficiency and reliability.

Supercritical fluids, particularly …

Cfd Modeling And Simulation Of Natural Circulation In Helium- Cooled Very High Temperature Reactors, Mohammad Sakib U. Abrar

Dissertations and Theses

This thesis investigates the thermal-hydraulic behavior of natural circulation in helium-cooled Very High Temperature Reactor (VHTR) systems, focusing on the performance and validation of passive safety features under Pressurized or Depressurized Loss of Forced Cooling (P-LOFC or D-LOFC) events. An experimental facility inspired by the General Atomics 350 MWt Modular High Temperature Gas-Cooled Reactor (MHTGR) was developed at The City College of New York. The setup consists of a plenum-to-plenum flow loop with four riser and four downcomer tubes, each equipped with heating coils, thermocouples, and pressure sensors. Natural circulation is driven by density gradients induced by asymmetric heating of …

Advanced Air Preheater Sealing Systems For Enhanced Efficiency And Reliability In Thermal Power Plants, Pavan Kumar Ravulaparthy

Theses and Dissertations

Global electricity generation still relies heavily on thermal power plants, which consume vast amounts of fuel and emit significant amounts of carbon dioxide. A major but often overlooked source of inefficiency in these plants lies within the rotary regenerative air preheater (RAPH), a critical heat-exchange component where air leakage can exceed 20% in aging units. This leakage increases fuel consumption, parasitic fan power, and CO₂ emissions, while degrading boiler reliability.

This research introduces advanced adaptive sealing systems designed to mitigate these losses by dynamically compensating for rotor eccentricity, thermal distortion, and wear under harsh operating conditions. Brush seals, composed of …

Propulsion Heat Analysis Nuclear Trajectory Optimization (Phantom), Ana Clecia Alves Almeida, Jonathan Davis, Ryan Dippolito

Williams Honors College, Honors Research Projects

Interplanetary Travel requirements necessitate the use of increasingly complex propulsion systems. Nuclear Thermal Propulsion (NTP) is a cutting-edge concept that holds immense potential for the future of space exploration. By utilizing nuclear fission to heat a propellant and generate thrust, NTP offers the potential for unprecedented efficiency, enabling faster interplanetary travel and extended mission capabilities. A nuclear thermal rocket engine is a type of propulsion system that utilizes the heat generated by a nuclear reactor to heat and expel a propellant, typically hydrogen, at high velocities to produce thrust. The engine consists of three main subsystems: the nuclear reactor, the …

Fluid Flow And Thermal Performance Investigation Of Twisted Elliptical Tubes For Use In High Prandtl Number Systems, Connor F. Donlan

Theses and Dissertations

The development of clean energy systems is paramount to reducing mankind's climate impact. These clean energy systems include solar, wind, and nuclear power where nuclear power shows a reduced lifetime carbon dioxide footprint per kilowatt hour compared to other sources [102]. Advanced nuclear reactors, fusion energy systems, and concentrated solar power designers are looking at using molten salt heat transfer fluids and improved heat exchanger design to increase power production and efficiency of clean energy systems. The improving heat transfer within the main heat transfer components within advanced nuclear reactors will enable increased efficiencies and power production.

Heat transfer improvements …

Enercon Station Vacuum Pump Replacement, Clint Hembree, Jared D'Amico, Connor Moore, Paul Jeffrey Fontenot, Sydnee Castello, J.J. Clements

Senior Design Project For Engineers

This details the progress of the ENERCON pump replacement project as completed by the Kennesaw State University interdisciplinary senior design group. This project is a two-semester capstone effort for the engineering program at Southern Polytechnic School of Engineering, overseen by Dr. McFall during Fall 2020 and Dr. Khalid during Spring 2021 semesters. The 2020-2021 KSU Interdisciplinary Senior Design team was tasked with completing an Engineering Change Package (ECP) for existing vacuum pumps at ENERCON Station. The mechanical, electrical, and civil students worked together, performing evaluations on existing plant systems to ensure the plant could support the new vacuum pumps. By …

Numerical Simulations Of Transcritical Natural Convection, Ruiwen Wei, Carlo Scalo, Mario Tindaro Migliorino, Kukjin Kim, Jean-Pierre Hickey

The Summer Undergraduate Research Fellowship (SURF) Symposium

In modern engineering applications, system overheating is a key issue that needs to be solved with efficient and reliable cooling technologies. Among the possible mechanisms that these are based on, natural convection cooling is one of the most frequently employed, with applications ranging from cooling of computer micro-components to large nuclear reactors. While many studies have been performed on natural convection employing supercritical or subcritical fluids, little attention has been given to fluids in their transcritical regime. The latter has the potential to yield high performances while avoiding detrimental effects of two-phase systems (e.g. cavitation). In the present study, 2D …

Evaluation And Enhancement Of Clean Energy Systems: Analytical, Computational And Experimental Study Of Solar And Nuclear Cycles, Nima Fathi

Mechanical Engineering ETDs

Clean (and specifically renewable) energy is steadily improving its global share. However, finite availability of fossil fuels and the growing effects of climate change make it an urgent priority to convince the industry and governments to incentivize investment in the renewable energy field and to make it more attractive by decreasing the capital cost. Until recently, uncertainties in funding limited renewable energy development, especially in the US. That limitation has been one of the barriers to progress. Another limitation of many renewable energy systems is the variability in their output, which makes them unsuitable for baseline power production. Therefore, fossil …

Computer Simulation Of Pore Migration Due To Temperature Gradients In Nuclear Oxide Fuel, Ian Wayne Vance

Graduate Theses and Dissertations

A phase-field simulation model is being presented that captures the thermal-gradient-driven migration of pores in oxide fuel associated with fuel restructuring. The model utilizes a Cahn-Hilliard equation supplemented with an advection term to describe the vapor transport of fuel material through the pore interior due to gradients in vapor pressure. In addition, the model also captures changes in a migrating pores’ morphology. Simulations demonstrate that the model successfully predicts pore migration towards the hottest portion of the fuel, the centerline. The simulations also demonstrate changes in pore shape that are in agreement with previous experimental observations. Initially isotropic pores are …

A Study Of High Temperature Heat Pipes And The Impact Of Magnetic Field On The Flow Of Liquid Metal, Udit Sharma

Dissertations, Master's Theses and Master's Reports

A study of high temperature heat pipe was conducted to understand its characteristics. A review of working fluid, temperature, wick structure, problems, operational limit and applications was done. Alkali metal were concluded as the most viable candidate for the working fluid.

The impact of three parameters namely magnetic field, heat flux and temperature was analyzed on the performance of HTHP (High Temperature Heat Pipe). The presence of magnetic field had the most considerable impact on reducing the pumping limit of the heat pipe while the temperature had almost negligible effect. Magnetic field results in the pressure drop and adversely affect …

High Temperature Heat Exchanger Annual Report, Anthony Hechanova

Publications (NSTD)

Objectives

• Identify candidate materials for heat exchanger components.

• Test candidate materials for heat exchanger components.

• Design critical components in the interface between the reactor and hydrogen production plant and within the sulfur iodine thermochemical process.

• Fabricate prototypical components.

• Test prototypical components.

Knowledge-Based Information Resource Management System For Materials Of Sodium-Cooled Fast Reactor, Sean Hsieh

Reactor Campaign (TRP)

In the development of advanced fast reactors, materials and coolant/material interactions pose a critical barrier for higher temperature and longer core life designs. For advanced burner reactors (sodium cooled) such as EBR-II and FFTF, experience has shown that the qualified structural materials and fuel cladding severely limits the economic performance. In other liquid metal cooled reactor concepts, advanced materials and better understanding and control of coolant and materials interactions are necessary for realizing the potentials.

Liquid sodium has been selected as the primary coolant candidate for Gen. IV nuclear energy systems. Global Nuclear Partnership (GNEP) Advanced Burned Reactor (ABR) has …

Modeling And Design Algorithms For Electromagnetic Pumps, Daniel P. Cook, Yitung Chen, Jian Ma

Reactor Campaign (TRP)

Electromagnetic (EM) induction pumps are used extensively in current and proposed nuclear power systems and industrial molten metal transfer operations. Although the Magnetohydrodynamic (MHD) theory that underlies the operation of these types of pumps has been studied extensively in the past few decades, the design of specific EM pumping systems for specific flow cases requires computational tools and expertise, which is lacking in the U.S. However, for the past two years, researchers at UNLV have been utilizing the TC-1 liquid metal loop system at UNLV and an Annular Linear Induction Pump (ALIP) to drive the liquid metal and to develop …

Thermal Transient Flow Rate Sensor For High Temperature Liquid Metal Cooled Nuclear Reactor, Yingtao Jiang, Jian Ma

Reactor Campaign (TRP)

In nuclear power plants and accelerator driven systems (ADS) for nuclear waste treatment, it is important to monitor the coolant flow rate in the reactor core and pipe-line. In such a strong irradiation, high pressure, and temperature environment, the existing flow measurement techniques (such as Electromagnetic flow meters, Ultrasonic flow meters, Turbine flow meters, etc.) are not accurate and reliable.

The measurement of flow rates (mass flow rates or volume flow rate) plays a notable role in monitoring and controlling the experimental conditions. The bulk flow rates can be obtained through direct methods, which measure the amount of discharged fluids …

Knowledge-Based Information Resource Management System For Materials Of Sodium-Cooled Fast Reactor, Sean Hsieh

Reactor Campaign (TRP)

In the development of advanced fast reactors, materials and coolant/ material interactions pose a critical barrier for higher temperature and longer core life designs. For sodium-cooled fast reactors (SFRs) such as the Experimental Breeder Reactors in Idaho and the Fast Flux Test Facility in Hanford, experience has shown that qualified structural materials and fuel cladding severely limits their economic performance.

Liquid sodium has been selected as the primary coolant candidate for the Advanced Burner Reactor (ABR) of the Global Nuclear Partnership (GNEP). Materials improvement has been identified as a major thrust to improve fast reactor economics. Researchers from universities, national …

High Temperature Heat Exchanger Project: Quarterly Progress Report July 1, 2007 Through September 30, 2007, Anthony Hechanova

Publications (NSTD)

• Ceramatec Sulfuric Acid Decomposer. The numerical model of a SiC ceramic coupon with two layers of microchannels was developed. Calculations of the factor of safety and probability of failure for the case of a straight channel were performed. Results for a pressure of 7.5 MPa were performed. The thermal and mechanical stress analyses of the Ceramatec HTHX and decomposer were completed.

• Bayonet Heat Exchanger. The thermal and mechanical stress analyses of the bayonet type HTHX and decomposer (Sandia design) were completed. Temperature profiles obtained from thermocouples measured from the Sandia experiments have been applied to the whole packed …

Unlv Research Foundation High Temperature Heat Exchanger Development: 9/08, Anthony Hechanova

Publications (NSTD)

Barriers addressed:

Nuclear Hydrogen Initiative R&D Plan – Material performance and component design and testing for the intermediate heat exchanger and high-temperature thermochemical water splitting (H₂SO₄ decomposition and HI decomposition). Improved materials for High Temperature Electrolysis.

High Temperature Heat Exchanger Project: Quarterly Progress Report April 1, 2007 Through June 30, 2007, Anthony Hechanova

Publications (NSTD)

• Ceramatec Sulfuric Acid Decomposer. Modeling with different reacting flow channel configurations (ribbed-surface channels, hexagonal channels, and diamond-shaped channels) was performed. The probability of failure for the one channel geometry with different reacting flow channel configurations was calculated to be zero in the three principal directions for all of the cases.

• Bayonet Heat Exchanger. The Matlab code for calculating the probability of failure using a two-dimensional axisymmetric model of the bayonet decomposer was developed. The probability of failure was calculated for the inner and outer SiC walls, and the intermediate quartz wall of the decomposer and found to be …

High Temperature Heat Exchanger Project: Quarterly Progress Report January 1, 2007 Through March 31, 2007, Anthony Hechanova

Publications (NSTD)

• The variation of sulfur dioxide production (throughput) of the baseline design of the Ceramatec sulfuric acid decomposer with total mass flow rate of reacting flow has been calculated. According to the calculations, the sulfur dioxide production increases as the total mass flow rate of reacting flow increases regardless of the fact that decomposition percentage of sulfuric trioxide decreases. A parametric study of the baseline design of the Ceramatec sulfuric acid decomposer was performed.

• The thermal performance using various channel geometries for the decomposer was studied. The baseline design (straight channels) has 89.5% thermal efficiency while the thermal efficiency …

High Temperature Heat Exchanger Project: Quarterly Progress Report October 1, 2006 Through December 31, 2006, Anthony Hechanova

Publications (NSTD)

Modifications to the single-channel models of the Ceramatec heat exchanger and decomposer concept for hexagonal flow channels under two values of layer-overlapping (50% and 100%) and for diamond-shaped flow channels were completed.

The finite element calculations of the “Ball on Three Ball Test” for ceramic material for the purpose of selecting the appropriate specimen thickness for future experimental testing was performed for plate thicknesses ranging from 2 to 8 mm.

A finite element model of the “Ball on Three Ball Test” was also studied for discs having micro-channels.

Modeling And Design Algorithms For Electromagnetic Pumps, Daniel P. Cook

Reactor Campaign (TRP)

Electromagnetic (EM) induction pumps are used in a number of nuclear energy related applications, such as circulation of molten lead-bismuth eutectic alloys in neutron targets, and circulation of liquid sodium metal in Gen IV Sodium-cooled Fast Reactors (SFR). Because EM pumps have no moving parts which can fail, they are considerably more reliable than conventional mechanical pumps for molten metal usage, and thus EM pumps are favored over mechanical pumps even though their pumping efficiency is lower and their initial cost is higher when compared to mechanical pumps of similar flow rates.

The research objectives of this task are:

• A …

Thermal Transient Flow Rate Sensor For High Temperature Liquid Metal Cooled Nuclear Reactor, Yingtao Jiang

Reactor Campaign (TRP)

In nuclear power plants and accelerator driven system (ADS) for nuclear waste treatment, it is important to monitor the coolant flow rate in the reactor core and pipe-line. In such a strong irradiation, high pressure and temperature environment, no accurate local flow measurement technique is readily available. Electromagnetic (EM) flow meter is popular in low temperature application as it is a non-intrusive technology. However, additional voltage will be produced due to temperature, flow, pressure, the chemical properties of the liquid metal and surface condition of the steel walls. In addition, the non-definite wetting behavior of liquid lead-bismuth to the electrically …

High Temperature Heat Exchanger Project: Quarterly Progress Report July 1, 2006 Through September 30, 2006, Anthony Hechanova

Publications (NSTD)

Hydrodynamics and thermal numerical modeling coupled with sulfur trioxide decomposition for the one channel geometry with three different channel configurations were performed. The results obtained from the numerical modeling were compared with the baseline design under the same boundary and operation conditions. The case with diamond shaped channels has the highest percentage of sulfuric acid decomposition. The baseline channel geometry has the lowest pressure drop compared with other cases.

High Temperature Heat Exchanger Project: Quarterly Progress Report April 1, 2006 Through June 30, 2006, Anthony Hechanova

Publications (NSTD)

Numerical Analyses of the Ceramatec Sulfuric Acid Decomposer. Comparisons with experiments for the Ceramatec sulfuric acid decomposer coupon with eight straight channels for four different geometries and four different flow rates were performed. All of the operation and boundary conditions for the calculations were the same as in the Ceramatec experiments. Good agreement was found. The overall pressure drop difference between calculations and experiments for most of the cases is within 10%.

High Temperature Heat Exchanger Project: Quarterly Progress Report January 1, 2006 Through March 31, 2006, Anthony Hechanova

Publications (NSTD)

Quarterly Collaboration Meeting. The UNLVRF HTHX Project quarterly meeting was held in Albuquerque, NM, March 16 and 17, 2006. The purpose of the meeting was to promote collaboration and communication among the UNLV Research Foundation partners. A tour of Sandia National Laboratory was also provided that included a visit to their sulfuric acid decomposition test apparatus. There were 24 attendees from universities, national laboratories, and private industry. Collaborators discussed their research progress. The next meeting will be in July in Salt Lake City, UT.

Unlv Research Foundation High Temperature Heat Exchanger Development, Anthony Hechanova

Publications (NSTD)

Barriers addressed:

Nuclear Hydrogen Initiative R&D Plan – Material performance and component design and testing for: intermediate heat exchanger and high-temperature thermochemical water splitting (H2SO4 decomposition and HI decomposition). Improved materials for High Temperature Electrolysis.

High Temperature Heat Exchanger Project: Quarterly Progress Report October 1, 2005 Through December 31, 2005, Anthony Hechanova

Publications (NSTD)

• Liquid Salt Technical Working Group Meeting. The first meeting of the Liquid Salt Technical Working Group was held on October 28, 2005 at the Pratt Whitney Rocketdyne facility in Canoga Park, CA. 20 experts from academia, industry, and national laboratories participated to discuss current state of knowledge and research needs for high temperature liquid salt applications.
• Nuclear Hydrogen Initiative Semi-annual Review. Several participants from the UNLVRF University Consortium gave technical presentations at the NHI Semi-annual Review meeting in Rockville, MD, November 9-10, 2005.
• Quarterly Collaboration Meeting. The University of Nevada, Las Vegas hosted a UNLVRF HTHX Project quarterly meeting December …

Magnetohydrodynamic Simulation Of Electromagnetic Pump In Tc-1, Lillian J. Ratliff

Reactor Campaign (TRP)

The pilot molten lead-bismuth target circuit (TC-1) in university of Nevada Las Vegas (UNLV) was designed for beam power of 1 MW accelerator driven system (ADS). The TC-1 is a liquid lead-bismuth eutectic (LBE) circulation loop. Circulation of the liquid alloy is driven by an annular linear induction pump (ALIP). Experimental measurements of system parameters have yielded a surprisingly low pump efficiency of less than 1%. A numerical study of the pump efficiency is being conducted to determine which operational parameters are responsible for this low efficiency and to give insight into future EM pump design. The numerical study will …

High Temperature Heat Exchanger Project: Quarterly Progress Report July 1, 2005 Through September 30, 2005, Anthony Hechanova

Publications (NSTD)

Quarterly Collaboration Meeting. The University of California, Berkeley, hosted a UNLVRF HTHX Project quarterly meeting on September 12. The purpose of the meeting was to promote collaboration and communication among the UNLV Research Foundation partners. Collaborators discussed their research program plan and provided an update on their progress. The next meeting will be in December in Las Vegas, NV hosted by UNLV.

High Temperature Heat Exchanger Project: Quarterly Progress Report April 1, 2005 Through June 30, 2005, Anthony Hechanova

Publications (NSTD)

Quarterly Collaboration Meeting. General Atomics hosted a UNLVRF HTHX Project quarterly meeting on June 5 in San Diego, California. The purpose of the meeting was to promote collaboration and communication among the UNLV Research Foundation partners. Collaborators had the opportunity to discuss their research program plan and update their progress. The next meeting will be in September in Berkeley hosted by UC Berkeley.

HTHX Computational Design (UNLV). Work on optimizing the ceramic offset strip in compact HTHX design through parametric studies was performed and completed. A simple single channel model was used to perform parametric studies on dimensions and flow …