Heat Transfer, Combustion Commons^™

Cyclic Combustion Pressure Dynamics Of A Diesel Engine Operating On Waste Frying Oil Biodiesel Blends Using Wavelets, Shady Elmozy, Ahmed Khaira Dr., Elshenawy Elshenawy Prof. Dr., Ali Mohamed Dr., Medhat Elkelawy Prof. Dr,

Journal of Engineering Research

This paper investigates the cyclic combustion pressure dynamics of a single-cylinder diesel engine burning waste frying oil biodiesel blends, employing statistical analysis and continuous wavelet transform (CWT) to evaluate combustion stability. Experiments were conducted at a constant engine load (90%) and speed (1500 rpm), with in-cylinder pressure data collected over 400 consecutive cycles for conventional diesel (RD) and biodiesel blends (UB10, UB30, UB50). Results demonstrate that biodiesel blends marginally reduce average peak cylinder pressure (PP) by 0.3–3.8% while lowering PP variability, evidenced by declining coefficients of variation (COV-PP: 1.27–1.48%), attributed to biodiesel’s elevated viscosity promoting consistent fuel-air mixing. Conversely, mean …

Combustion Characteristics And Cycle-To-Cycle Variations In A Diesel Generator Fueled With Used Frying Oil Biodiesel Blends, Shady Elmozy, Ahmad Khira Dr., E. A. El Shenawy Prof. Dr., Medhat Elkelawy Prof. Dr, Eng.

Journal of Engineering Research

This paper investigates the combustion characteristics and cycle-to-cycle variations in a stationary direct-injection diesel generator fueled with biodiesel derived from used frying oil (UFO) blended with conventional diesel. Used frying oil methyl ester (UFOME), referred to as UB100, was produced through a single-step alkali transesterification process and blended with diesel fuel in varying proportions (UB10, UB20, UB30, UB40, and UB50). Experiments were conducted on a single-cylinder, naturally aspirated diesel engine operating at a constant speed of 1500 rpm under five different load conditions: 0%, 25%, 50%, 75%, and 90%. In-cylinder pressure data from 400 consecutive cycles were analyzed to determine …

Numerical Investigation Of Heat Transfer And Pressure Drop In A Circular Microchannel Using Sio₂ Nanofluids, Mahmoud G. Abdelfatah, Osama E. Abd-Ellatif, Ahmed A. A. Attia, Abdelrady O. Elnady

Journal of Engineering Research

A numerical investigation was conducted to analyze the flow characteristics and heat transfer performance of a circular microchannel. using water and SiO₂+pure water nanofluids with volume fractions of 0.3%, 0.7%, and 1%. The microchannel was subjected to a constant heat flux of 100W, and the pressure drop, friction factor, and thermal resistance were evaluated for different Reynolds numbers ranging from 250 to 850. The results show that the addition of SiO₂ nanoparticles enhances the thermal performance of the microchannel by reducing the thermal resistance by up to 1.9% compared to pure water. However, the pressure drop increases with higher Np …

A Review Of Performance Assessment Of Solar-Driven Absorption Chillers Incorporated With Energy Storage Systems, A. Khalil, Mohamed Abdelgaied, May Abdelsalam

Journal of Engineering Research

Abstract- This study evaluates the performance of a solar

collector absorption chiller combined with Phase Change Material (PCM) energy storage devices. Solar energy is used for energy-efficient cooling, and PCM storage improves

efficiency by capturing surplus thermal energy during

abundant solar radiation and releasing it when insufficient. The research assesses performance measures like

COP, energy storage capacity, and overall system efficiency.

Review Of Wood Drying Technologies, Mohamed Salah Elmetwaly, Lotfy Hassan Rabie Saker, Mohamed Sameh Salem

Journal of Engineering Research

Abstract- This article provides a comprehensive review of drying optimization in data centers by examining the limitations of drying methods and discussing advances proposed by scientists through whom we can provide a comparison between different drying systems with an emphasis on improving energy efficiency and thermal performance. Wood drying under atmospheric pressure has many advantages, including the ability to dry at lower temperatures (by reducing the likelihood of some drying defects), significantly reduced drying times, color preservation, increased energy efficiency, better control of volatile organic compound emissions, and the ability to dry very large cross sections. Previous studies have achieved …

Heat And Mass Transfer Characteristics During Vacuum Drying Of Wood, Mohamed Salah Elmetwaly, Lotfy Hassan Rabie Saker, Mohamed Sameh Salem

Journal of Engineering Research

The properties affecting the characteristics of heat and mass transfer during vacuum drying of wood are studied in this paper. The experimental work is carried out in 0.0365 m³ test rig vacuum dryer. The drying chamber dimensions are 0.5 m long and 0.305 m diameter carbon steel cylinder. This drying chamber is internally coated with epoxy paint, also this chamber is detachable closing caps at both ends meaning welded at one end and bolted at the other end to facilitate loading and unloading of the specimen. Two stainless steel heat exchanger plates with dimensions 0.3 m length, 0.15 m …

Performance Augmentation Of Single-Slope Solar Distiller Using An Evacuated Tube Solar Collector: Theoretical Study, Eman Mohammed Abuelezz Eng., Yasser El-Samadony Prof., Khaled Khodary Esmaeil Assoc. Prof., Mohamed Elsheshtawy Zayed Dr.

Journal of Engineering Research

In this research, the performance analysis of a solar-powered desalination system incorporating a single slope-slope solar still and an evacuated tube solar collector is theoretically investigated. The system comprises a solar evacuated tube that absorbs solar radiation, transferring heat to saline water. This water then flows into a solar still, where it absorbs solar energy, boosting the evaporation rate. Two solar distillers, namely the conventional solar distiller (Still-I) and solar still integrated with evacuated tube solar collector (Still-II), are simulated and analyzed under identical outdoor conditions in Tanta, Egypt. A comprehensive theoretical model, developed using FORTAN programming, simulates the performance …

Enhancing The Performance Of Conventional Solar Still Using The Nano-Doped Paint (Ndp) Coating, Hagar Alm-Eldin Bastawissi Prof.Dr, Nermin Elgendy Engineer, Ayman R. El-Tohamy

Journal of Engineering Research

Nations are throughout the entire globe continuously confronting the problem of potable water shortage. Recently, it has been thought that using solar energy to desalinate brackish water offers a practical answer to the world's water crises. The output of these stills, is meager, and academics haven't done much to boost it in any way. Solar distillers have been proposed as an efficient method to produce potable water. In recent years, saltwater has produced drinking water by various ways. The efficiency of a solar distiller is significantly influenced by various factors, most important factor of them is the absorber surface. In …