Nanotechnology Fabrication Commons^™

The Dawn Of New Quantum Dots: Synthesis And Characterization Of Ge1-Xsnx Nanocrystals For Tunable Bandgaps., Richard J. Esteves

Theses and Dissertations

Ge_1-xSn_x alloys are among a small class of benign semiconductors with composition tunable bandgaps in the near-infrared spectrum. As the amount of Sn is increased the band energy decreases and a transition from indirect to direct band structure occurs. Hence, they are prime candidates for fabrication of Si-compatible electronic and photonic devices, field effect transistors, and novel charge storage device applications. Success has been achieved with the growth of Ge_1-xSn_x thin film alloys with Sn compositions up to 34%. However, the synthesis of nanocrystalline alloys has proven difficult due to larger discrepancies (~14%) in …

Nanosphere Lithography And Its Application In Rapid And Economic Fabrication Of Plasmonic Hydrogenated Amorphous Silicon Photovoltaic Devices, Chenlong Zhang

Dissertations, Master's Theses and Master's Reports

Solar photovoltaic (PV) devices harvest energy from solar radiation and convert it to electricity. PV technologies, as an alternative to traditional fossil fuels, use clean and renewable energy while minimizing pollution. For decades researchers have been developing thin film solar cells as an important alternatives to the relatively expensive bulk crystal solar cell technology. Among those, hydrogenated amorphous silicon (a-Si:H) solar cells prevails for good efficiency, non-toxic and materially abundant nature. However, a-Si:H thickness must be minimized to prevent light induced degradation, so optical enhancement is necessary. Light manipulation has to be applied and carefully engineered to trap light within …

Electric Field Controlled Strain Induced Switching Of Magnetization Of Galfenol Nanomagnets In Magneto-Electrically Coupled Multiferroic Stack, Hasnain Ahmad

Theses and Dissertations

The ability to control the bi-stable magnetization states of shape anisotropic single domain nanomagnets has enormous potential for spawning non-volatile and energy-efficient computing and signal processing systems. One of the most energy efficient switching methods is to adopt a system of a 2-phase multiferroic nanomagnet, where a voltage applied on the piezoelectric layer generates a strain in it and the strain is elastically transferred to the magnetostrictive nanomagnet which rotates the magnetization states of the nanomagnet at room temperature via the converse magnet-electric effect. Recently, it has been demonstrated that the magnetization of a Co nanomagnet can be switched between …

Beyond Conventional C-Plane Gan-Based Light Emitting Diodes: A Systematic Exploration Of Leds On Semi-Polar Orientations, Morteza Monavarian

Theses and Dissertations

Despite enormous efforts and investments, the efficiency of InGaN-based green and yellow-green light emitters remains relatively low, and that limits progress in developing full color display, laser diodes, and bright light sources for general lighting. The low efficiency of light emitting devices in the green-to-yellow spectral range, also known as the “Green Gap”, is considered a global concern in the LED industry. The polar c-plane orientation of GaN, which is the mainstay in the LED industry, suffers from polarization-induced separation of electrons and hole wavefunctions (also known as the “quantum confined Stark effect”) and low indium incorporation efficiency that …

Optical Investigations Of Ingan Heterostructures And Gesn Nanocrystals For Photonic And Phononic Applications: Light Emitting Diodes And Phonon Cavities, Shopan D. Hafiz

Theses and Dissertations

InGaN heterostructures are at the core of blue light emitting diodes (LEDs) which are the basic building blocks for energy efficient and environment friendly modern white light generating sources. Through quantum confinement and electronic band structure tuning on the opposite end of the spectrum, Ge_1−xSn_x alloys have recently attracted significant interest due to its potential role as a silicon compatible infra-red (IR) optical material for photodetectors and LEDs owing to transition to direct bandgap with increasing Sn. This thesis is dedicated to establishing an understanding of the optical processes and carrier dynamics in InGaN heterostructures for achieving …

Hybrid Straintronics-Spintronics: Energy-Efficient Non-Volatile Devices For Boolean And Non-Boolean Computation, Ayan K. Biswas

Theses and Dissertations

Research in future generation computing is focused on reducing energy dissipation while maintaining the switching speed in a binary operation to continue the current trend of increasing transistor-density according to Moore’s law. Unlike charge-based CMOS technology, spin-based nanomagnetic technology, based on switching bistable magnetization of single domain shape-anisotropic nanomagnets, has the potential to achieve ultralow energy dissipation due to the fact that no charge motion is directly involved in switching. However, switching of magnetization has not been any less dissipative than switching transistors because most magnet switching schemes involve generating a current to produce a magnetic field, or spin transfer …

Epitaxial Growth Of Si-Ge-Sn Alloys For Optoelectronic Device Application, Aboozar Mosleh

Graduate Theses and Dissertations

Microelectronics industry has experienced a tremendous change over the last few decades and has shown that Moore’s law has been followed by doubling the number of transistors on the chip every 18 months. However, continuous scaling down of the transistors size is reaching the physical limits and data transfer through metal interconnects will not be able to catch up with the increasing data processing speed in the future. Therefore, optical data transfer between chips and on-chip has been widely investigated. Silicon based optoelectronics has received phenomenal attention since Si has been the core material on which microelectronic industry has been …

Skin Effect Suppression In Infrared-Laser Irradiated Planar Multi-Walled Carbon Nanotube/Cu Conductors, Kamran Keramatnejad, Yang Gao, Yunshen Zhou, Hossein Rabiee Glogir, Mengmeng Wang, Yongfeng Lu

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Skin effect suppression in planar multi-walled carbon nanotube (MWCNT)/Copper (Cu) conductors was realized at the 0-10 MHz frequency range through infrared laser irradiation of MWCNTs, which were coated on the surface of the Cu substrate via the electrophoretic deposition (EPD) method. The effect of laser irradiation and its power density on electrical and structural properties of the MWCNT/Cu conductors was investigated using a wavelength-tunable CO2 laser and then comparing the performance of the samples prepared at different conditions with that of pristine Cu. The irradiation at λ=9.219 μm proved to be effective in selective delivery of energy towards depths close …

A Comparative Study Of Polyurethane Nanofibers With Different Patterns And Its Analogous Nanofibers Containing Mwcnts, Javier Macossay-Torres, Faheem A. Sheikh, Hassan Ahmad, Hern Kim, Gary L. Bowlin

School of Integrative Biological & Chemical Sciences (Formerly Dept. of Chemistry)

Tissue engineering is a multidisciplinary field that has evolved in various dimensions in recent years. One of the main aspects in this field is the proper adjustment and final compatibility of implants at the target site of surgery. For this purpose, it is desired to have the materials fabricated at the nanometer scale, since these dimensions will ultimately accelerate the fixation of implants at the cellular level. In this study, electrospun polyurethane nanofibers and their analogous nanofibers containing MWCNTs are introduced for tissue engineering applications. Since MWCNTs agglomerate to form bundles, a high intensity sonication procedure was used to disperse …

Simulating Nanowires And Ultra-Thin Body Transistors Using Nemo5 On Nanohub.Org, Liang Yuan Dai, James E. Fonseca, Chu Yuan Chen, Gerhard Klimeck

The Summer Undergraduate Research Fellowship (SURF) Symposium

During the past twenty years, the most important aspects of semiconductor electronics have advanced into the nanometer range, resulting in exponential increases of microprocessor computing performance. As the size of electrical components continues to shrink, the cost of experimental research and industrial fabrication in this field has increased dramatically. Thus, the development of accurate nanoscale model simulations becomes necessary as a measure to decrease the high financial expenses of advancing semiconductor technology. This simulator supports atomistic modeling in order to provide an accurate description of the nanoscale devices, as current electrical components operate in the quantum regime and are affected …

Mass-Positioning Of Nanodiamonds Using Squeegee Technique, Ran Cui, Mikhail Y. Shalaginov, Vladimir M. Shalaev

The Summer Undergraduate Research Fellowship (SURF) Symposium

Fluorescent color centers in diamond nanocrystals have recently become the focus of researchers because of their potential applications in quantum information processing, nano-sensing, biomarking, and bioimaging. One of the biggest challenges in working with nanodiamonds is how to position them precisely and efficiently to create strong interaction with nanoscale photonic structures. The most popular methods to position nanodiamonds are spin-coating and transporting via scanning probe microscope tip. On the one hand, spin-coating, where nanodiamonds are randomly located, is not precise; on the other hand, the tip-based technique, where a single nanodiamond is picked and dropped, is tedious and time-consuming. Hence, …

Simplified Generation Of The Input Models Of Object Oriented Micromagnetic Framework (Oommf), Jinyang Yu, Rafatul Faria, Supriyo Datta, Tanya A. Faltens

The Summer Undergraduate Research Fellowship (SURF) Symposium

Object Oriented MicroMagnetic Framework (OOMMF) is a micromagnetic simulation tool. It takes a memory initialization file (MIF) as the input and outputs various forms of data such as data table, graph and magnetic configuration plots. It is accurate and fast compared to other existing tools such as MATLAB. Few experimentalists used it in the past, however, due to two main reasons. First, OOMMF requires a specific version of programming environment on the local computer which is difficult to be installed. Second, MIF file is very complicated to code and it also requires users to read a lengthy guidelines. Our solution …

Optical Anisotropy Of Porous Polymer Film With Inverse Slanted Nanocolumnar Structure Revealed Via Generalized Spectroscopic Ellipsometry, Dan Liang, Derek Sekora, Charles Rice, Eva Schubert, Mathias Schubert

Department of Electrical and Computer Engineering: Faculty Publications

We use generalized spectroscopic ellipsometry to characterize the biaxial optical properties of porous polymer and slanted nanocolumnar template thin films. The porous polymer with inverse columnar structure was prepared via infiltrating polymer into the voids of the slanted nanocolumnar film and selectively removing the column material (cobalt). The anisotropic Bruggeman effective medium approximation was employed to analyze the ellipsometry data of the porous polymer film and nanocolumnar template. The classification and structure of optical anisotropy are found to be identical for both samples. The interchangeable optical behaviors between two complementary structures are attributed to the equivalency in their anisotropic polarizabilities.

Swelling-Etching Characterization Of Copper (I) Oxide - Pdms For The Development Of Micro/Nano - Particles Composite Mems Corrosion Sensor, Abdoul Kader Maiga

Graduate Theses and Dissertations

The primary objective for this thesis is to contribute to the understanding of the oxide removal process for a corrosion sensing device. The goal for designing such a device is for monitoring corrosion on metallic structures. The sensing material (6.35mm x 1mm discs) of the device is composed of copper (I) oxide particles mixed in some polydimethylsiloxane (PDMS). The PDMS, “housing,” is meant for controlling the oxidation rate through the sensing material. A solvent was used to facilitate the etchant diffusion through the PDMS matrix. Toluene and acetic acid were the ideal solvent and etchant, respectively, for carrying out the …

Broadband High Efficiency Fractal-Like And Diverse Geometry Silicon Nanowire Arrays For Photovoltaic Applications, Omar Hassan Al-Zoubi

Graduate Theses and Dissertations

Solar energy has many advantages over conventional sources of energy. It is abundant, clean and sustainable. One way to convert solar energy directly into electrical energy is by using the photovoltaic solar cells (PVSC). Despite PVSC are becoming economically competitive, they still have high cost and low light to electricity conversion efficiency. Therefore, increasing the efficiency and reducing the cost are key elements for producing economically more competitive PVSC that would have significant impact on energy market and saving environment. A significant percentage of the PVSC cost is due to the materials cost. For that, thin films PVSC have been …

Synthesis, Characteristics, And Material Properties Dataset Of Bi:Dyig-Oxide Garnet-Type Nanocomposites, M Nur-E-Alam, Mikhail Vasiliev, Kamal Alameh

Research outputs 2014 to 2021

The fabrication, annealing crystallization processes, and material properties of (Bi,Dy)3(Fe,Ga)5O12:Bi2O3 nanocomposites are investigated and summarized. The stoichiometry of these nanocomposites is optimized for magnetooptic applications using the approach of stoichiometry adjustment (implemented by means of varying RF power densities applied to the sputtering targets used to prepare the nanocomposite thin films). The crystallization processes for all developed batches of as-deposited films are carried out by annealing runs at different temperatures and process durations. This paper describes the methodologies used to optimize the compositions (by calculating the volumetric fractions of excess bismuth oxide to be mixed with the garnet-stoichiometry species during …

Enhancement Of The Performance Of Gaas Based Solar Cells By Using Plasmonic, Anti-Reflection Coating And Hydrophobic Effects, Yahia Fayiz Makableh

Graduate Theses and Dissertations

Investigation of renewable energy resources is gaining huge momentum in recent years due to the limited fossil fuels, and their detriment impact on the environment. Solar energy is promising to meet the increased energy demand. In order to achieve this goal, solar energy has to be harvested efficiently at low cost. Therefore, higher efficiency solar cells are the primary focus of research worldwide. Photovoltaics based on InAs/GaAs intermediate band solar cells and their device performance enhancements are investigated in this dissertation. The device enhancement is carried out by surface modification methods. The dissertation work is inspired by the need of …

Single-Walled Carbon Nanotube Arrays For High Frequency Applications, Asmaa Elkadi

Graduate Theses and Dissertations

This dissertation presents a thorough analysis of semiconducting Single-Walled Carbon Nanotube-based devices, followed by a test structure fabrication and measurements.

The analysis starts by developing an individual nanotube model, which is then generalized for many nanotubes and adding the parasitic elements. The parasitic elements appear when forming the device electrodes degrade the overall performance.

The continuum model of an individual nanotube is developed. A unique potential function is presented to effectively describe the electron distribution in the carbon nanotube subsequently facilitating solving Schrödinger's equation to obtain the energy levels, and to generalize the model for many nanotubes.

It is shown …

Modular Approach To Spintronics, Kerem Yunus Camsari

Open Access Dissertations

There has been enormous progress in the last two decades, effectively combining spintronics and magnetics into a powerful force that is shaping the field of memory devices. New materials and phenomena continue to be discovered at an impressive rate, providing an ever-increasing set of building blocks that could be exploited in designing transistor-like functional devices of the future. The objective of this thesis is to provide a quantitative foundation for this building block approach, so that new discoveries can be integrated into functional device concepts, quickly analyzed and critically evaluated. Through careful benchmarking against available theory and experiments we establish …

Fabrication And Characterization Of Polycarbonate Polyurethane (Pcpu) Nanofibers Impregnated With Nanofillers, Hruday Chand Katakam

USF Tampa Graduate Theses and Dissertations

Polycarbonate polyurethane (PCPU) has been studied as a novel polymer impregnated with nanoparticles for improved mechanical, thermal and adhesion properties [4]. This study investigates the synthesis of polycarbonate polyurethane (PCPU) polymeric nanofiber membranes by the process of electrospinning. This study further examines all the parameters associated with electrospinning a novel PCPU polymeric solution impregnated with nanofillers, such as nanoparticles, to produce fiber membranes. Tetrahydrofuran (THF) and N, N dimethylformamide (DMF) are used as solvents to dissolve PCPU polymer. One percent (1%) of nanofillers like silver and silica nanoparticles are added to PCPU polymer solution to investigate the impact on polymer …

Multiferroic Tunnel Junctions And Ferroelectric Control Of Magnetic State At Interface, Y. W. Yin, M. Raju, W. J. Hu, John D. Burton, Y.-M. Kim, A. Y. Borisevich, S. J. Pennycook, S. M. Yang, T. W. Noh, Alexei Gruverman, X. G. Li, Z. D. Zhang, Evgeny Y. Tsymbal, Qi Li

Alexei Gruverman Publications

As semiconductor devices reach ever smaller dimensions, the challenge of power dissipation and quantum effect place a serious limit on the future device scaling. Recently, a multiferroic tunnel junction (MFTJ) with a ferroelectric barrier sandwiched between two ferromagnetic electrodes has drawn enormous interest due to its potential applications not only in multi-level data storage but also in electric field controlled spintronics and nanoferronics. Here, we present our investigations on four-level resistance states, giant tunneling electroresistance (TER) due to interfacial magnetoelectric coupling, and ferroelectric control of spin polarized tunneling in MFTJs. Coexistence of large tunneling magnetoresistance and TER has been observed …

Electron-Beam Patterning Of Teflon Af For Surface Plasmon Resonance Sensing, Mansoor A. Sultan

Theses and Dissertations--Electrical and Computer Engineering

Variable pressure electron beam etching and lithography for Teflon AF has been demonstrated. The relation between dose and etching depth is tested under high vacuum and water vapor. High resolution structures as small as 75 nm half-pitch have been resolved. Several simulation tools were tested for surface plasmon excitation. Grating based dual mode surface plasmon excitation has been shown numerically and experimentally.

Trapping Light With Nanostructures For Sensors, Kareem Garriga

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Nanostructured Semiconductor Device Design In Solar Cells, Hongmei Dang

Theses and Dissertations--Electrical and Computer Engineering

We demonstrate the use of embedded CdS nanowires in improving spectral transmission loss and the low mechanical and electrical robustness of planar CdS window layer and thus enhancing the quantum efficiency and the reliability of the CdS-CdTe solar cells. CdS nanowire window layer enables light transmission gain at 300nm-550nm. A nearly ideal spectral response of quantum efficiency at a wide spectrum range provides an evidence for improving light transmission in the window layer and enhancing absorption and carrier generation in absorber. Nanowire CdS/CdTe solar cells with Cu/graphite/silver paste as back contacts, on SnO₂/ITO-soda lime glass substrates, yield the …

Explorations For Efficient Reversible Barrel Shifters And Their Mappings In Qca Nanocomputing, Ke Chen

Theses and Dissertations--Electrical and Computer Engineering

This thesis is based on promising computing paradigm of reversible logic which generates unique outputs out of the inputs and. Reversible logic circuits maintain one-to-one mapping inside of the inputs and the outputs. Compared to the traditional irreversible computation, reversible logic circuit has the advantage that it successfully avoids the information loss during computations. Also, reversible logic is useful to design ultra-low-power nanocomputing circuits, circuits for quantum computing, and the nanocircuits that are testable in nature. Reversible computing circuits require the ancilla inputs and the garbage outputs. Ancilla input is the constant input in reversible circuits. Garbage output is the …

Strain Controlled Ultra-Low-Energy Magnetic Tunneling Junction, Hasnain Ahmad, Supriyo Bandyopadhyay, Jayasimha Atulasimha

Graduate Research Posters

We are experimenting on designing a voltage-controlled ultra-low-energy Magnetic Tunneling Junction (MTJ) device using a soft single domain magnetostrictive layer (i.e. Galfenol: Fe_1-xGa_x , x = 20 At%) coupled to a piezoelectric layer (i.e. PMN-PT). Special metal pads have been designed using photolithography to generate stress in the PMN-PT layer by applying electric field. The patterns of different shape anisotropic nano-magnets are designed using e-beam lithography and we have successfully fabricate FeGa nanomagnets with only 12 to 13 nanometer thickness by sputter deposition. These nanomagnets have been characterized by magnetic force microscopy for observing their switching capabilities. …

Coherent Spin Transport In Nanowire Spin Valves And Novel Spintronic Device Possibilities, Md Iftekhar I. Hossain, Supriyo Bandyopadhyay, Jayasimha Atulasimha, Saumil Bandyopadhyay

Graduate Research Posters

We have proposed a spintronic infrared photodetector backed by experimental evidence and matched with theoretical prediction obtained in our labs. Unlike conventional photodetectors, it can work at room temperature with ideally infinite light-to-dark contrast ratio, infinite detectivity and zero dark current. The proposed idea is based on smart implementation of spin polarized transport. Electrons while travelling through one-dimensional channel show long spin relaxation length if they can be confined to a single conduction subband because of the elimination of major spin relaxation mechanism, namely the D’yakonov-Perel’ mechanism. With infrared light, electrons can be excited to higher subbands, resulting in the …

Metal Assisted Nanowire Growth For Silicon Nanowire/Amorphous Silicon Composite Solar Cell, Asmaa Ali Sadoon

Graduate Theses and Dissertations

Solar cells are photovoltaic devices that convert the energy of light to electricity by the photovoltaic effect. Crystalline silicon-based solar cells are the most dominant solar cells in the market today due to the high efficiency and relatively low cost. However, the cost of such solar cell is still high due to the large amount of material that is consumed in fabricating such a device. Polycrystalline/amorphous thin films and nanomaterial technologies have emerged to reduce the high cost of c-Si based solar cells and increase the efficiency. In this research, we combined these two technologies to propose and fabricate silicon …

Radiation-Induced Effects In Chalcogenide-Based Memory Devices And Films, Kasandra Wolf

Boise State University Theses and Dissertations

Continued scaling of memory devices has produced many issues for the current foremost non-volatile memory—the flash memory—leading to the emergence of a wide variety of alternative memory solutions. Redox Conductive Bridge Memory (RCBM) is one such solution that has shown great promise in recent years. However, the performance of these devices under radiation conditions has not been explored in detail. This work investigates the effects of x-rays and electron bombardment on chalcogenide glasses and RCBM devices based on these materials.

RCBM devices are a form of Resistance Change Memory, which rely on two distinct resistive states to represent the binary …

Fabrication And Comparison Of Electrospun Cobalt Oxide-Antimony Doped Tin Oxide (Coo-Ato) Nanofibers Made With Ps: D-Limonene And Ps: Toluene, Manopriya Devisetty Subramanyam

USF Tampa Graduate Theses and Dissertations

This work investigates the fabrication, process optimization, and characterization of cobalt oxide-antimony doped tin oxide (CoO-ATO) nanofibersusing polystyrene (PS) solutions with toluene orD-limonene as solvents. These nanofibers are produced by anelectrospinning process. Nanofibers are fabricated using polymeric solutions of CoO doped ATO and mixtures of PS: D-limonene and PS:toluene. PSis a base aromatic organic polymer, a non-toxic material, and a versatile catalyst for fiber formation. PSsolutions are made by mixing polystyrene beads and D-limonene or toluene at specific weight percentages. These polymeric solutions of PS: D-limonene and PS:toluene are then mixed with CoO-ATO at various weight percentages. The two solutions …