Nanotechnology Fabrication Commons^™

Virtual-Source Based Accurate Model For Predicting Noise Behavior At High Frequencies In Nanoscale Pmos Soi Transistors, Vaibhav R. Ramachandran, Saeed Mohammadi, Sutton Hathorn

The Summer Undergraduate Research Fellowship (SURF) Symposium

Complementary Metal Oxide Semiconductor (CMOS) technology at the nanometre scale is an excellent platform to implement monolithically integratedsystems because of the low cost of manufacturing and ease of integration. Newly developed CMOS Silicon on Insulator (SOI) transistors that are currentlydeveloped are suitable for use in radio frequency circuits. They find applications in many areas such as 5G telecommunication systems, high speed Wi-Fi andairport body-scanners. Unfortunately, the models for CMOS SOI transistors that are currently used in these circuits are inaccurate because of their complexity.The models currently used require the optimization of more than 200 variables. This paper aims to accurately …

Improving Methods Of Doping On Black Phosphorus, Yuqin Duan, Adam Charnas, Jingkai Qin, Peide Ye

The Summer Undergraduate Research Fellowship (SURF) Symposium

Black phosphorus (BP) is a 2D semiconducting material with high carrier mobility. It is usually p-type due to oxidation states near its valence band. Although achieved through other growth methods, n-type doping has not yet been accomplished through the modern chemical vapor transport (CVT) growth method. To address this issue, small amounts of tellurium were added to Red Phosphorus to act as a dopant during the CVT growth process in addition to tin(Sn) and tin(IV) iodide, which facilitate growth. The chemicals are heated up to 600°C and precisely cooled in a 21-hour process, during which BP crystals should form. After …

Laser-Assisted Metal Organic Chemical Vapor Deposition Of Gallium Nitride, Hossein Rabiee Golgir

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Due to its unique properties, gallium nitride is of great interest in industry applications including optoelectronics (LEDs, diode laser, detector), high power electronics, and RF and wirelss communication devices. The inherent shortcomings of current conventional deposition methods and the ever-increasing demand for gallium nitride urge extended efforts for further enhancement of gallium nitride deposition. The processes of conventional methods for gallium nitride deposition, which rely on thermal heating, are inefficient energy coupling routes to drive gas reactions. A high deposition temperature (1000-1100 °C) is generally required to overcome the energy barriers to precursor adsorption and surface adatom migration. However, there …

Investigating The Classical And Non-Classical Mechanical Properties Of Gan Nanowires, Mohammad Reza Zamani Kouhpanji

Electrical and Computer Engineering ETDs

Study and prediction of classical and non-classical mechanical properties of GaN is crucial due to the potential application of GaN nanowires (NWs) in piezoelectric, probe-based nanometrology, and nanolithography areas. GaN is mainly grown on sapphire substrates whose lattice constant and thermal expansion coefficient are significantly different from GaN. These discrepancies cause mechanical defects and high residual stresses and strains in GaN, which reduce its quantum efficiency.

Specifically, for nanoscale applications, the mechanical properties of materials differ significantly compared to the bulk properties due to size-effects. Therefore, it is essential to investigate the mechanical properties of GaN NWs using the non-classical …

Studies In Mesoscopics And Quantum Microscopies, Zhenghao Ding, Gabriel C. Spalding

Honors Projects

This thesis begins with a foundational section on quantum optics. The single-photon detectors used in the first chapter were obtained through the Advanced Laboratory Physics Association (ALPhA), which brokered reduced cost for educational use, and the aim of the single-photon work presented in Chapter 1 is to develop modules for use in Illinois Wesleyan's instructional labs beyond the first year of university. Along with the American Association of Physics Teachers, ALPhA encourages capstone-level work, such as Chapter 1 of this honors thesis, which is explicitly designed to play the role of passing on, to a next generation of physics majors, …

Development Of Intermediate Band Solar Cell Through Ingan Quantum Well Structures, Kelly Mckenzie

Electrical Engineering Undergraduate Honors Theses

In the search for high-efficiency solar cells, In_xGa_1-xN has come under scrutiny as a unique material with high potential. This is due to characteristics including an easily tunable bandgap, large range of potential bandgap values, and high heat resistance. However, one factor limiting its adaptation is the high density of crystal defects. In this thesis, the qualities of InGaN are discussed and the intermediate band solar cell structure is introduced. Additionally, the growth and characterization of two sets of InGaN-based solar cell devices are reported and evaluated.

Compositionally Graded Indium Gallium Nitride Solar Cells, Christopher Matthews

Electrical Engineering Undergraduate Honors Theses

For the past several decades, methods to harvest solar energy have been investigated intensively. A majority of the work done in this field has been on solar cells made with silicon – the most mature semiconductor material. Recent developments in material fabrication and processing techniques have enabled other semiconductor materials to attract practical interest and research effort as well. Indium gallium nitride (InGaN) is one such material. The material properties of InGaN indicate that solar cells made with it have the potential to achieve much higher power density than a standard silicon solar cell. High power density InGaN solar cells …

Characterization Of Coupled Gold Nanoparticles In A Sparsely Populated Square Lattice, Roy Truett French Iii

Graduate Theses and Dissertations

Metal nanoparticles deposited in regular arrays spaced at optical wavelengths support a resonance due to a coherent coupling between localized surface plasmon mode and lattice diffraction allowing for engineering of tunable devices for use in biological sensors, nanoantennae, and enhanced spectroscopy. Techniques such as electron beam lithography, focused ion beam lithography, nanosphere lithography, and nanoimprint lithography are used for fabrication but are limited by cost, device throughput, and small deposition. Polymer soft lithography and continuous dewetting of particles is a potentially viable alternative showing promise in all of those areas. This thesis developed the fabrication of a refined hydrophilic nanoimprinted …

Optimization Of Reduced Graphene Oxide Deposition For Hydrogen Sensing Technologies, Matthew Pocta

Mechanical Engineering Undergraduate Honors Theses

Graphene is known to be a key material for improving the performance of hydrogen sensors. High electrical conductivity, maximum possible surface area with respect to volume, and high carrier mobility are a few of the properties that make graphene ideal for hydrogen sensing applications. The problem with utilizing graphene is the difficulty in depositing uniform, thin layers onto substrate surfaces. This study examines a new method of optimizing graphene deposition by utilizing an airbrush to deposit both graphene oxide (GO) and reduced graphene oxide (rGO) onto glass substrates. The number of depositions were varied among samples to study the effect …

Optimization Of Graphene Parameters For The Development Of Supercapacitors, Jessica L. Montgomery

Mechanical Engineering Undergraduate Honors Theses

In the growing market of evolving electronic devices and the sustainable goals of the energy industry, better sources of energy dense storage devices are needed. Carbon based supercapacitors have attracted the attention of research due to the natural properties of high electrical conductivity, chemical and electrochemical stability, and high surface area. The object of this thesis is to expand upon current knowledge of reduced graphene oxide to better understand the effectiveness of the material as electrode in supercapacitors. This thesis will focus on the physical orientation of supercapacitors to further develop a device that will allow a set of supercapacitors …

Environmentally Friendly Synthesis Of Transition Metalorganic Hybrid Nanocomposites, Aubrey N. Penn

Masters Theses & Specialist Projects

Research on metal nanoparticles (MNPs) synthesis and their applications for optoelectronic devices has been a recent interest in the fields of nanoscience and nanotechnology Photovoltaics are one of such systems in which MNPs have shown to be quite useful, due to unique physical, optical, magnetic, and electronic properties, including the metal nanoparticles synthesized in this research.

Owing to the challenges with the most common physical and chemical methods of preparing MNPs, including the use of high temperatures, toxic reducing agents, and environmentally hazardous organic solvents, there is a critical need for a benign synthesis procedure for MNPs. In this work, …

Coherent/Incoherent Magnetization Dynamics Of Nanomagnetic Devices For Ultra-Low Energy Computing, Md Mamun Al-Rashid

Theses and Dissertations

Nanomagnetic computing devices are inherently nonvolatile and show unique transfer characteristics while their switching energy requirements are on par, if not better than state of the art CMOS based devices. These characteristics make them very attractive for both Boolean and non-Boolean computing applications. Among different strategies employed to switch nanomagnetic computing devices e.g. magnetic field, spin transfer torque, spin orbit torque etc., strain induced switching has been shown to be among the most energy efficient. Strain switched nanomagnetic devices are also amenable for non-Boolean computing applications. Such strain mediated magnetization switching, termed here as “Straintronics”, is implemented by switching the …

Optical Spectroscopy Of Wide Bandgap Semiconductor Heterostructures And Group-Iv Alloy Quantum Dots, Tanner A. Nakagawara

Theses and Dissertations

Efficient and robust blue InGaN multiple quantum well (MQW) light emitters have become ubiquitous; however, they still have unattained theoretical potential. It is widely accepted that “localization” of carriers due to indium fluctuations theoretically enhance their efficiency by moderating defect-associated nonradiative recombination. To help develop a complete understanding of localization effects on carrier dynamics, this thesis explores degree of localization in InGaN MQWs and its dependence on well thickness and number of wells, through temperature and power dependent photoluminescence measurements. Additionally, silicon-compatible, nontoxic, colloidally synthesizable 2-5 nm Ge_1-xSn_x alloy quantum-dots (QDs) are explored for potential visible to …

Low-Temperature Fabrication Process For Integrated High-Aspect Ratio Metal Oxide Nanostructure Semiconductor Gas Sensors, William Paul Clavijo

Theses and Dissertations

This work presents a new low-temperature fabrication process of metal oxide nanostructures that allows high-aspect ratio zinc oxide (ZnO) and titanium dioxide (TiO₂) nanowires and nanotubes to be readily integrated with microelectronic devices for sensor applications. This process relies on a new method of forming a close-packed array of self-assembled high-aspect-ratio nanopores in an anodized aluminum oxide (AAO) template in a thin (2.5 µm) aluminum film deposited on a silicon and lithium niobate substrate (LiNbO₃). This technique is in sharp contrast to traditional free-standing thick film methods and the use of an integrated thin aluminum film …

Design Automation For Carbon Nanotube Circuits Considering Performance And Security Optimization, Lin Liu

Dissertations, Master's Theses and Master's Reports

As prevailing copper interconnect technology advances to its fundamental physical limit, interconnect delay due to ever-increasing wire resistivity has greatly limited the circuit miniaturization. Carbon nanotube (CNT) interconnects have emerged as promising replacement materials for copper interconnects due to their superior conductivity. Buffer insertion for CNT interconnects is capable of improving circuit timing of signal nets with limited buffer deployment. However, due to the imperfection of fabricating long straight CNT, there exist significant unidimensional-spatially correlated variations on the critical CNT geometric parameters such as the diameter and density, which will affect the circuit performance.

This dissertation develops a novel timing …

Nanostructured Morphologies In Glassy Polymer Networks, Brian Greenhoe

Dissertations

The body of this work describes a novel approach for the dispersion of multi-walled carbon nanotubes in a high T_g epoxy prepolymer matrix using a twin screw high-shear continuous reactor. The method demonstrated improves on previous dispersion methods in several ways. It offers increased efficiency through excellent heat transfer, while being solvent-less, scale-able, and tailorable to drive dispersion states to judiciously chosen dispersion states. Furthermore, it was shown that dispersion state and agglomerate morphology can be directed, in several ways, through processing conditions and also by controlling the matrix viscosity profile through cure. Broadband dielectric spectroscopy, optical hot-stage microscopy, …

Strategies And Techniques For Fabricating Mems Bistable Thermal Actuators., Dilan Ratnayake

Electronic Theses and Dissertations

Bistable elements are beginning to appear in the field of MEMS as they allow engineers to design sensors and actuators which require no electrical power and possess mechanical memory. This research focuses on the development of novel strategies and techniques for fabricating MEMS bistable structures to serve as no electrical power thermal actuators. Two parallel strategies were explored for the design and fabrication of the critical bistable element. Both strategies involved an extensive material study on candidate thin film materials to determine their temperature coefficient of expansion and as-deposited internal stress properties. Materials investigated included titanium tungsten, Invar, silicon nitride …

Fabrication Of Infrared Photodetectors Utilizing Lead Selenide Nanocrystals, Justin Anthony Hill

Graduate Theses and Dissertations

Colloidal lead selenide and lead selenide / lead sulfide core/shell nanocrystals were grown using a wet chemical synthesis procedure. Absorbance and photoluminescence measurements were made to verify the quality of the produced nanocrystals. Absorbance spectra were measured at room temperature, while photoluminescence spectra were measured at 77 K. Organic ligands were exchanged for shorter ligands in order to increase the conductivity of the nanocrystals. Absorption and PL spectra for both core and core/shell nanocrystals were compared. Interdigital photodetector devices with varying channel widths were fabricated by depositing gold onto a glass substrate. Lead selenide nanocrystals were deposited onto these metallic …

Dispersion Of Particles In Liquid Metal Using Contactless Electromagnetic Stirring, Koulis A. Pericleous, Valdis Bojarevics, Georgi S. Djambazov

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Surface Feature Engineering Through Nanosphere Lithography, Tod V. Laurvick, Ronald A. Coutu Jr., James M. Sattler, Robert A. Lake

Faculty Publications

How surface geometries can be selectively manipulated through nanosphere lithography (NSL) is discussed. Self-assembled monolayers and multilayers of nanospheres have been studied for decades and have been applied to lithography for almost as long. When compared to the most modern, state-of-the-art techniques, NSL offers comparable feature resolution with many advantages over competing technologies.

Atomistic Configuration Interaction Simulation Tool For Semiconductor Based Quantum Computing Devices, Jingbo Wu, Archana Tankasala, Jim Fonseca, Rajib Rahman, Gerhard Klimeck

The Summer Undergraduate Research Fellowship (SURF) Symposium

Solid-state devices are promising candidates for quantum computing applications due to obvious advantages in compatibility with semiconductor fabrication technologies and the extremely long coherent times of electron and nuclear spins in these devices. In such devices, electron interactions are crucial for single and two qubit gate operations. Thus it is essential to evaluate these electron-electron interactions accurately for precise qubit control. It is shown that Atomistic Configuration Interaction can be used to accurately determine electron-electron interactions in realistic semiconductor quantum computing devices. In this work, an online simulation tool on Atomistic Configuration Interaction has been implemented and published on nanoHUB.org, …

Wearable Piezotronic Devices For Heart Rate Monitoring, Adam J. Miller, Wenzhuo Wu Dr.

The Summer Undergraduate Research Fellowship (SURF) Symposium

Self-powered multifunctional wearable devices that are capable of human-device interfacing are highly desired. Piezotronic devices utilize piezoelectricity and semiconductor properties to enable devices to have seamless interaction between human and device. One important use for piezotronic devices is for pressure sensing. Pressure sensing devices have been employed in smart skins, biomonitoring, gesture recognition, and many more applications. This study aims to create a flexible piezotronic device, specifically for use in pressure sensing to monitor heart rate. ZnO nanowires are grown on a flexible polymer substrate so that they can be made into wearable devices. A p-n heterojunction is formed by …

Reward Modulated Spike Timing Dependent Plasticity Based Learning Mechanism In Spiking Neural Networks, Shrihari Sridharan, Gopalakrishnan Srinivasan, Kaushik Roy

The Summer Undergraduate Research Fellowship (SURF) Symposium

Spiking Neural Networks (SNNs) are one of the recent advances in machine learning that aim to further emulate the computations performed in the human brain. The efficiency of such networks stems from the fact that information is encoded as spikes, which is a paradigm shift from the computing model of the traditional neural networks. Spike Timing Dependent Plasticity (STDP), wherein the synaptic weights interconnecting the neurons are modulated based on a pair of pre- and post-synaptic spikes is widely used to achieve synaptic learning. The learning mechanism is extremely sensitive to the parameters governing the neuron dynamics, the extent of …

Mechanical Reliability Of Implantable Polyimide-Based Magnetic Microactuators For Biofouling Removal, Christian G. Figueroa-Espada, Qi Yang, Hyowon Lee

The Summer Undergraduate Research Fellowship (SURF) Symposium

Hydrocephalus is a neurological disorder that typically requires a long-term implantation of a shunt system to manage its symptoms. These shunt systems are notorious for their extremely high failure rate. More than 40% of all implanted shunt systems fail within the first year of implantation. On average, 85% of all hydrocephalus patients with shunt systems undergo at least two shunt-revision surgeries within 10 years of implantation. A large portion of this high failure rate can be attributed to biofouling-related obstructions and infections. Previously, we developed flexible polyimide-based magnetic microactuators to remove obstructions formed on hydrocephalus shunts. To test the long-term …

Simultaneous Behavior Onset Detection And Task Classification For Patients With Parkinson Disease Using Subthalamic Nucleus Local Field Potentials, Nazanin Zaker Habibabadi

Electronic Theses and Dissertations

This thesis aims to develop of methods for behavior onset detection of patients with Parkinson's disease (PD), as well as to investigate the models for classification of different behavioral tasks performed by PD patient. The detection is based on recorded Local Field Potentials (LFP) of the Subthalamic nucleus (STN), captured through Deep Brain Stimulation (DBS) process.

One main part of this work is dedicated to the research of various properties and features of the STN LFP signals of several patients' behavior conditions. Features based on temporal and time-frequency analysis of the signals are developed and implemented. Evaluation and comparison of …

Investigation Of Cnt-Induced Escherichia Coli Lysis And Protein Release, Abdollah Mosleh

Graduate Theses and Dissertations

This research investigated the use of carbon nanotubes (CNTs) as a treatment to increase the permeability of a bacterial cell wall. Recombinant Escherichia coli BL21 (DE3) containing a plasmid that expressed Green Fluorescent Protein (GFP) and -lactamase were exposed to CNTs under various levels of agitation for different times. Fluorescence assay for GFP, optical absorbance for -lactamase activity, and Transmission Electron Microscopy (TEM) were used to determine the amount of released protein, and visually examine the permeability enhancement of the cells, respectively. It was found that more -lactamase was present in the culture fluid after treatment with CNTs in a …

Investigation Of Optical Properties Of Zinc Oxide Photodetector, Tyler Chism

Graduate Theses and Dissertations

UV photodetection devices have many important applications for uses in biological detection, gas sensing, weaponry detection, fire detection, chemical analysis, and many others. Today’s photodetectors often utilize semiconductors such as GaAs to achieve high responsivity and sensitivity. Zinc oxide, unlike many other semiconductors, is cheap, abundant, non-toxic, and easy to grow different morphologies at the micro and nano scale. With the proliferation of these devices also comes the impending need to further study optics and photonics in relation to phononics and plasmonics, and the general principles underlying the interaction of photons with solid state matter and, specifically, semiconductors. For this …

Genotoxicity Of Graphene In Escherichia Coli, Ananya Sharma

Graduate Theses and Dissertations

Rapid advances in nanotechnology necessitate assessment of the safety of nanomaterials in the resulting products and applications. One key nanomaterial attracting much interest in many areas of science and technology is graphene. Graphene is a one atom thick carbon allotrope arranged in a two-dimensional honeycomb lattice. In addition to being extremely thin, graphene has several extraordinary physical properties such as its exceptional mechanical strength, thermal stability, and high electrical conductivity. Graphene itself is relatively chemically inert and therefore pristine graphene must undergo a process called functionalization, which is combination of chemical and physical treatments that change the properties of graphene, …

Heating Element Including Carbon Nanotube (Cnt) Layer, Santhosh Kumar Loganathan, Virginie Rollin, Daewon Kim

Publications

Apparatus , materials , and techniques and techniques herein can include providing a deposited layer comprising a com posite material including carbon nanotubes ( CNTs ) . Accord ing to various examples , the composite can be applied to a substrate such as using a solution containing CNTs and other constituents such as sulfur . The solution can be spray applied to a substrate , or spin - coated upon a substrate , such as to provide a uniform , conductive , and optically - transpar ent film layer . In one application , such a film layer can be …

Electron Beam Induced Deposition Of Highly Conductive Copper Nanowires From Bulk Liquids, Amjad M. Syam

Theses and Dissertations--Electrical and Computer Engineering

Electron-beam induced deposition (EBID) is a position-controlled technique that can directly fabricate nanometer-sized structures in functional materials. In the standard process, a gaseous precursor delivers the desired substance to the substrate for deposition. However, the material purity from these precursors is typically poor, which often negatively affects the functional properties of the deposit. Recently, bulk liquid precursors have been investigated as promising reactants for high purity deposition without the need for post-processing. In this work, EBID from bulk liquids is shown to yield highly conductive nanowire deposits. Aqueous solutions containing copper sulfate (CuSO₄) and sulfuric acid (H_{2 …}