Nanotechnology Fabrication Commons^™

Characterization Of Coupled Gold Nanoparticles In A Sparsely Populated Square Lattice, Roy Truett French Iii

Graduate Theses and Dissertations

Metal nanoparticles deposited in regular arrays spaced at optical wavelengths support a resonance due to a coherent coupling between localized surface plasmon mode and lattice diffraction allowing for engineering of tunable devices for use in biological sensors, nanoantennae, and enhanced spectroscopy. Techniques such as electron beam lithography, focused ion beam lithography, nanosphere lithography, and nanoimprint lithography are used for fabrication but are limited by cost, device throughput, and small deposition. Polymer soft lithography and continuous dewetting of particles is a potentially viable alternative showing promise in all of those areas. This thesis developed the fabrication of a refined hydrophilic nanoimprinted …

Fabrication Of Infrared Photodetectors Utilizing Lead Selenide Nanocrystals, Justin Anthony Hill

Graduate Theses and Dissertations

Colloidal lead selenide and lead selenide / lead sulfide core/shell nanocrystals were grown using a wet chemical synthesis procedure. Absorbance and photoluminescence measurements were made to verify the quality of the produced nanocrystals. Absorbance spectra were measured at room temperature, while photoluminescence spectra were measured at 77 K. Organic ligands were exchanged for shorter ligands in order to increase the conductivity of the nanocrystals. Absorption and PL spectra for both core and core/shell nanocrystals were compared. Interdigital photodetector devices with varying channel widths were fabricated by depositing gold onto a glass substrate. Lead selenide nanocrystals were deposited onto these metallic …

Investigation Of Cnt-Induced Escherichia Coli Lysis And Protein Release, Abdollah Mosleh

Graduate Theses and Dissertations

This research investigated the use of carbon nanotubes (CNTs) as a treatment to increase the permeability of a bacterial cell wall. Recombinant Escherichia coli BL21 (DE3) containing a plasmid that expressed Green Fluorescent Protein (GFP) and -lactamase were exposed to CNTs under various levels of agitation for different times. Fluorescence assay for GFP, optical absorbance for -lactamase activity, and Transmission Electron Microscopy (TEM) were used to determine the amount of released protein, and visually examine the permeability enhancement of the cells, respectively. It was found that more -lactamase was present in the culture fluid after treatment with CNTs in a …

Investigation Of Optical Properties Of Zinc Oxide Photodetector, Tyler Chism

Graduate Theses and Dissertations

UV photodetection devices have many important applications for uses in biological detection, gas sensing, weaponry detection, fire detection, chemical analysis, and many others. Today’s photodetectors often utilize semiconductors such as GaAs to achieve high responsivity and sensitivity. Zinc oxide, unlike many other semiconductors, is cheap, abundant, non-toxic, and easy to grow different morphologies at the micro and nano scale. With the proliferation of these devices also comes the impending need to further study optics and photonics in relation to phononics and plasmonics, and the general principles underlying the interaction of photons with solid state matter and, specifically, semiconductors. For this …

Genotoxicity Of Graphene In Escherichia Coli, Ananya Sharma

Graduate Theses and Dissertations

Rapid advances in nanotechnology necessitate assessment of the safety of nanomaterials in the resulting products and applications. One key nanomaterial attracting much interest in many areas of science and technology is graphene. Graphene is a one atom thick carbon allotrope arranged in a two-dimensional honeycomb lattice. In addition to being extremely thin, graphene has several extraordinary physical properties such as its exceptional mechanical strength, thermal stability, and high electrical conductivity. Graphene itself is relatively chemically inert and therefore pristine graphene must undergo a process called functionalization, which is combination of chemical and physical treatments that change the properties of graphene, …

Epitaxial Growth Of Si-Ge-Sn Alloys For Optoelectronic Device Application, Aboozar Mosleh

Graduate Theses and Dissertations

Microelectronics industry has experienced a tremendous change over the last few decades and has shown that Moore’s law has been followed by doubling the number of transistors on the chip every 18 months. However, continuous scaling down of the transistors size is reaching the physical limits and data transfer through metal interconnects will not be able to catch up with the increasing data processing speed in the future. Therefore, optical data transfer between chips and on-chip has been widely investigated. Silicon based optoelectronics has received phenomenal attention since Si has been the core material on which microelectronic industry has been …

Swelling-Etching Characterization Of Copper (I) Oxide - Pdms For The Development Of Micro/Nano - Particles Composite Mems Corrosion Sensor, Abdoul Kader Maiga

Graduate Theses and Dissertations

The primary objective for this thesis is to contribute to the understanding of the oxide removal process for a corrosion sensing device. The goal for designing such a device is for monitoring corrosion on metallic structures. The sensing material (6.35mm x 1mm discs) of the device is composed of copper (I) oxide particles mixed in some polydimethylsiloxane (PDMS). The PDMS, “housing,” is meant for controlling the oxidation rate through the sensing material. A solvent was used to facilitate the etchant diffusion through the PDMS matrix. Toluene and acetic acid were the ideal solvent and etchant, respectively, for carrying out the …

Broadband High Efficiency Fractal-Like And Diverse Geometry Silicon Nanowire Arrays For Photovoltaic Applications, Omar Hassan Al-Zoubi

Graduate Theses and Dissertations

Solar energy has many advantages over conventional sources of energy. It is abundant, clean and sustainable. One way to convert solar energy directly into electrical energy is by using the photovoltaic solar cells (PVSC). Despite PVSC are becoming economically competitive, they still have high cost and low light to electricity conversion efficiency. Therefore, increasing the efficiency and reducing the cost are key elements for producing economically more competitive PVSC that would have significant impact on energy market and saving environment. A significant percentage of the PVSC cost is due to the materials cost. For that, thin films PVSC have been …

Enhancement Of The Performance Of Gaas Based Solar Cells By Using Plasmonic, Anti-Reflection Coating And Hydrophobic Effects, Yahia Fayiz Makableh

Graduate Theses and Dissertations

Investigation of renewable energy resources is gaining huge momentum in recent years due to the limited fossil fuels, and their detriment impact on the environment. Solar energy is promising to meet the increased energy demand. In order to achieve this goal, solar energy has to be harvested efficiently at low cost. Therefore, higher efficiency solar cells are the primary focus of research worldwide. Photovoltaics based on InAs/GaAs intermediate band solar cells and their device performance enhancements are investigated in this dissertation. The device enhancement is carried out by surface modification methods. The dissertation work is inspired by the need of …

Single-Walled Carbon Nanotube Arrays For High Frequency Applications, Asmaa Elkadi

Graduate Theses and Dissertations

This dissertation presents a thorough analysis of semiconducting Single-Walled Carbon Nanotube-based devices, followed by a test structure fabrication and measurements.

The analysis starts by developing an individual nanotube model, which is then generalized for many nanotubes and adding the parasitic elements. The parasitic elements appear when forming the device electrodes degrade the overall performance.

The continuum model of an individual nanotube is developed. A unique potential function is presented to effectively describe the electron distribution in the carbon nanotube subsequently facilitating solving Schrödinger's equation to obtain the energy levels, and to generalize the model for many nanotubes.

It is shown …

Investigation Of The Effects Of Rapid Thermal Annealing On Mbe Grown Gaasbi/Gaas Heterostructures For Optoelectronic Devices, Perry C. Grant

Graduate Theses and Dissertations

High efficiency optoelectronic devices rely on high quality materials making up the device structure. The scope of this thesis investigates the effectiveness of rapid thermal annealing (RTA) at improving the material quality of GaAsBi/GaAs heterostructures. During the fabrication of a device, the contacts of the device had the rapid thermal annealing process accomplished to produce ohmic contacts and this research explored if this annealing treatment degraded the quantum wells that made up the active region of a device. To investigate these effects, a system to measure the photoluminescence of the material system was constructed utilizing Fourier Transform Infrared Spectroscopy. The …

Monodentate, Bidentate And Photocrosslinkable Thiol Ligands For Improving Aqueous Biocompatible Quantum Dots, Hiroko Takeuchi

Graduate Theses and Dissertations

Water-soluble Quantum Dots (QDs) are highly sensitive fluorescent probes that are often used to study biological species. One of the most common ways to render QDs water-soluble for such applications is to apply hydrophilic thiolated ligands to the QD surface. However, these ligands are labile and can be easily exchanged on the QD surface, which can severely limit their application. As one way to overcome this limitation while maintaining a small colloidal size of QDs, we developed a method to stabilize hydrophilic thiolated ligands on the surface of QDs through the formation of a crosslinked shell using a photocrosslinking approach. …

Intermediate Band Solar Cells Based On Inas Quantum Dots Embedded In Ingaas Quantum Well, Ramesh Vasan

Graduate Theses and Dissertations

Intermediate band solar cells based on quantum dots and quantum wells with anti-reflection coating are investigated in this thesis. The demand for high efficient solar cells as an alternate source of energy is the main motivation for this research project. Intermediate band solar cells based on quantum dots were the subject of intensive research in recent years. High power conversion efficiency was predicted from InAs/GaAs intermediate band solar cells as the presence of InAs quantum dots increased the absorption below the band gap of the host material.

In this thesis, an attempt has been made to further increase the absorption …

New Effects Of Aging And Lattice Intercalation On Surface Properties Of Titanate Nanobelts, Roger Williams

Graduate Theses and Dissertations

Titanate nanobelts (NBs) have structural characteristics beyond that of clays. Due to a negatively charged lattice matrix of edge-shared TiO6-octahedra, the location of intercalated cations within the interlayer space may dictate the charge-conductions. This environment may in turn govern the lattice-framework's stability and surface properties, based upon our preliminary

data.

On that basis, these nanomaterials have been found in our lab to possess superb biological compatibility that is closely related to the types of the intercalated cations. In addition, a prolonged agitation was proven to enable us to manipulate the titanate NBs' length. In a parallel study, a ripening was …

Synthesis Of Optimized Inp/Zns Core/Shell Nanocrystals And Tio2 Nanotubes For Quantum Dot Sensitized Solar Cells, Seungyong Lee

Graduate Theses and Dissertations

Synthesis of InP/ZnS core/shell nanocrystals and TiO₂ nanotubes and the optimization study to couple them together were explored for quantum dot sensitized solar cells. Its intrinsic nontoxicity makes the direct band gap InP/ZnS core/shell be one of the most promising semiconductor nanocrystals for optoelectric applications, with the advantage of tuning the optical absorption range in the desired solar spectrum region. Highly luminescent and monodisperse InP/ZnS nanocrystals were synthesized in a non-coordinating solvent. By varying the synthesis scheme, different size InP/ZnS nanocrystals with emission peaks ranging from 520 nm to 620 nm were grown. For the purpose of ensuring air …

Hybrid Plasmonic Nanoantennas: Fabrication, Characterization, And Application, Shengjie Zhai

UNLV Theses, Dissertations, Professional Papers, and Capstones

As optical counterpart of microwave antennas, plasmonic nanoantennas are important nanoscale devices for converting propagating optical radiation into confined/enhanced electromagnetic fields. Presently, nanoantennas, with a typical size of 200-500 nm, have found their applications in bio-sensing, bio-imaging, energy harvesting, and disease cure and prevention. With the device feature size of next generation IC goes down to 22 nm or smaller, and biological/chemical sensing reaches the Gene’s level, the sizes of the corresponding nanoantennas have to be scaled down to sub-100nm level. In the literature, these sub-100nm nanoantennas are referred as deep subwavelength nanoantennas as size of such miniaturized nanoantennas is …

Molecular Dynamics Study Of Diffusion Of O2 Penetrates In Uncrosslinked Polydimethysiloxane (Pdms), Crosslinked Pdms, And Pdms-Based Nanocomposites, Varun Ullal

Graduate Theses and Dissertations

Molecular dynamics simulations are used to study diffusion of O₂ molecules in pure polydimethysiloxane (PDMS), crosslinked PDMS, and PDMS-based nanocomposites. The PDMS chains and penetrates are modeled using a hybrid interatomic potential which treats the Si-O atoms along the chain backbone explicitly while coarse-graining the methyl side groups and penetrates. By tracking the diffusion of penetrates in the system and subsequently computing their mean-squared displacement, diffusion coefficients are obtained. In pure PDMS models of varying molecular weight, diffusivity of the O₂2 penetrates is found to have an inverse relationship with chain length. Simulation models with longer chains …

Plasma-Assisted Molecular Beam Epitaxial Growth Of Indium Nitride For Future Device Fabrication, Steven Paul Minor

Graduate Theses and Dissertations

The need for energy conservation has heightened the search for new materials that can reduce energy consumption or produce energy by the means of photovoltaic cells. III-nitride alloys show promise for these applications due to their generally good transport properties and ability to withstand high power applications. Along with these, this family of semiconductor alloys has a direct bandgap energy range (0.7-6.2 eV) which spans the entire visible spectrum and encompasses a large portion of the available solar spectrum. Of the three root III-nitride semiconductors, AlN, GaN, and InN, InN has only recently become attainable epitaxially with qualities good enough …

Use Of Ultra High Vacuum Plasma Enhanced Chemical Vapor Deposition For Graphene Fabrication, Shannen Adcock

Graduate Theses and Dissertations

Graphene, what some are terming the "new silicon", has the possibility of revolutionizing technology through nanoscale design processes. Fabrication of graphene for device processing is limited largely by the temperatures used in conventional deposition. High temperatures are detrimental to device design where many different materials may be present. For this reason, graphene synthesis at low temperatures using plasma-enhanced chemical vapor deposition is the subject of much research. In this thesis, a tool for ultra-high vacuum plasma-enhanced chemical vapor deposition (UHV-PECVD) and accompanying subsystems, such as control systems and alarms, are designed and implemented to be used in future graphene growths. …

High Frequency Characterization Of Carbon Nanotube Networks For Device Applications, Emmanuel Decrossas

Graduate Theses and Dissertations

This work includes the microwave characterization of carbon nanotubes (CNTs) to design new CNTs-based high frequency components. A novel developed method to extract the electrical properties over a broad microwave frequency band from 10 MHz to 50 GHz of carbon nanotubes (CNTs) in a powder form is performed. The measured scattering parameters (S-parameters) with a performance network analyzer are compared to the simulated one obtained from an in-house computed mode matching technique (MMT). An optimized first order gradient method iteratively changes the unknown complex permittivity parameters to map the simulated S-parameters with the measured one until convergence criteria are satisfied. …

Fabrication Of Vertical Silicon Nanowires Through Metal Assisted Deposition, Matthew Garett Young

Graduate Theses and Dissertations

Controlled and ordered growth of Si nanowires through a low temperature fabrication method compatible with CMOS processing lines is a highly desirable replacement to future electronic fabrication technologies as well as a candidate for a low cost route to inexpensive photovoltaics. This stems from the fact that traditional CMOS based electronics are hitting physical barriers that are slowing the Moore's Law trend as well as the demand for an inexpensive solar cell technology that can obtain grid parity. A fractional factorial growth study is presented that compares the growth of Au and Al catalyzed Si nanowires at temperatures ranging from …

Fabrication Of Composite Nanomaterials For Thin Film Amorphous Silicon Solar Cells, Benjamin Seth Newton

Graduate Theses and Dissertations

A material with the precise combination of amorphous silicon and polycrystalline silicon would be able to take advantage of the high absorption capabilities of amorphous silicon and the electron transport capabilities of polycrystalline silicon. Polycrystalline nanostructures in the form of wires can also take advantage of other properties of light absorption, trapping and scattering inherent in nanowire structures. These properties of high absorption and electron transport in one device would lead to advances in the search for highly efficient low cost solar cells and sensors. In this work a thin film material composed of an array of polycrystalline silicon nanostructures …

Fabrication Of Horizontal Silicon Nanowires Using A Thin Aluminum Film As A Catalyst, Khaja Hafeezuddin Mohammed

Graduate Theses and Dissertations

Silicon nanowires have been the topic of research in recent years for their significant attention from the electronics industry to grow even smaller electronic devices. The semiconductor industry is built on silicon. Silicon nanowires can be the building blocks for future nanoelectronic devices. Various techniques have also been reported in fabricating the silicon nanowires. But most of the techniques reported, grow vertical silicon nanowires. In the semiconductor industry, integrated circuits are designed and fabricated in a horizontal architecture i.e. the device layout is flat compared to the substrate. When vertical silicon nanowires are introduced in the semiconductor industry, a whole …

Photodetectors And Photovoltaic Devices Based On Semiconductor Nanomaterials, Jiang Wu

Graduate Theses and Dissertations

Photodetectors based various nanostructures and plasmon enhanced solar cells are investigated in this dissertation. The motivation of the dissertation rise is driven by urgent need of both high efficiency photodetectors and solar cells.

First, quantum dot infrared photodetectors have been intensely investigated due to their promise in high performance photodetectors. However, the strain-driven growth of quantum dots has hindered the progress of quantum dot photodetectors. The presence of strain in the device presents complexity in designing as well as defects. Therefore, in this project, new designs of quantum dot photodetector structures are presented to improve the control over detection wavelength. …