Biomedical Devices and Instrumentation Commons^™

Using Noninvasive Calibrated Cuff Plethysmography To Observe The Effects Of Lifestyle Habits On Arterial Compliance, Joshua M. Whitaker

Master's Theses

Cardiovascular disease remains as a leading cause of death for both sexes and across all racial backgrounds. Continuing to research causes, early predictors, and preventative actions are paramount to ensuring that cardiovascular disease starts to decrease in its activity. Endothelial dysfunction is the earliest known predictor of cardiovascular disease, therefore investigating early detection methods of endothelial dysfunction can improve health outcomes. This study revolves around a non-invasive calibrated cuff device that uses the principles of segmental plethysmography and oscilliometry to measure arterial compliance of baseline and induced hyperemic conditions in human subjects to determine how well arteries vasodilate in response …

Synthesis And Study Of Stable Organic Radicals For Mri Contrast Agents And New Materials, Sabina Dhakal

Dissertations and Doctoral Documents, University of Nebraska-Lincoln, 2023–

The first part of this dissertation focuses on the design, synthesis, and characterization of a thermally robust S =1/2 phototetrazolinyl monoradical and the development of synthetic methodologies for a high-spin (S = 1) phototetrazolinyl diradical. Electrochemical studies of the phototetrazolium cation (precursor to the monoradical) revealed a remarkably narrow electrochemical band gap (Ecell ≈ 0.82 V), suggesting promising electrical conductivity. Thermal analysis of the monoradical demonstrated excellent stability, with the onset of decomposition at 232 °C. Building on the excellent thermal stability and promising properties for electrical conductivity of the monoradical, we developed two condensation-based synthetic routes that provide viable …

Comparative Assessment Of Lower Limb Neuromusculoskeletal Activation And Joint Kinematics In Normal And Impaired Gait, Jack Ryan Schule

Theses and Dissertations

This thesis evaluates whether accessible and affordable technologies can provide clinically significant, quantifiable gait analysis comparable to traditional marker-based motion capture systems. Modern high-end systems offer excellent accuracy but remain financially and logistically inaccessible to many clinicians and researchers. To address this gap, a framework was developed using markerless pose estimation using the model, MediaPipe, inertial measurement units (IMUs) processed through an Extended Kalman Filter (EKF), and surface electromyography (sEMG) to measure joint kinematics and neuromuscular activity during gait. An experiment was performed where data was collected from participants with both normal gait and pathologies including: Osgood–Schlatter disease, Plica Band …

Development Of A Non-Faradaic Impedimetric Biosensor Based On Reduced Graphene Oxide For The Detection Of Brain-Derived Neurotrophic Factor (Bdnf), Mariana N. Martins

Electronic Theses and Dissertations

Neurological disorders affect millions of people worldwide. In the case of Alzheimer’s disease (AD), the rising number of cases significantly increases global healthcare costs. Therefore, early detection of biomarkers at the onset of the disease is essential for early diagnosis. This study presents an electrochemical biosensor designed for the detection of Brain-Derived Neurotrophic Factor (BDNF) in human plasma, incorporating reduced graphene oxide (rGO) to enhance signal sensitivity. Dielectrophoresis (DEP) was employed to deposit rGO flakes on the electrode surface, improving conductivity and sensor performance. Electrochemical impedance spectroscopy (EIS) was used to monitor changes in impedance associated with BDNF binding events, …

Characterization Of The Fatigue Threshold Behavior Of Uhmwpe, Bethany B. Smith, Anurag Roy, Robert O. Ritchie, Lisa A. Pruitt

Faculty Journal Articles

Ultra-high-molecular-weight-polyethylene (UHMWPE) has been the material of choice for bearings in total joint replacements (TJRs) for decades as a result of its excellent wear resistance, chemical inertness, energetic toughness, low friction, and biocompatibility. Utilization of this polymer in orthopedic devices requires oxidation, wear, and fatigue resistance. Balancing these important properties by tailoring processing techniques and modulating microstructural features has been an ongoing endeavor in the field. Research into the clinical applications of UHMWPE has primarily focused on the challenges of wear and oxidation while studies into the realm of fatigue have been more limited. Literature gaps exist in fully understanding …

Novel Percutaneous Repair Of Femoral Pseudoaneurysms Using Perclose Proglide™: A Case Series, Ryan Mancoll, Emily Burnett, Nicholas Bandy, Benjamin Samberg, Thomas Cook, Jacob Hoffman, Christopher Murter, Matthew Rossi, David Dexter, Hosam El Sayed, Animesh Rathore Md

Cardiovascular Research Symposium

BACKGROUND - This case series details the novel use of the Perclose ProGlide closure device to successfully repair three separate cases of iatrogenic femoral pseudoaneurysms (PSAs) without attempting other modalities first. Conventional treatment methods of ultrasound-guided compression, duplex-directed thrombin injection (DDTI), or open surgical repair were contraindicated in these patients due to unique anatomy or advanced comorbidities.

METHODS – Details were gathered via a retrospective chart review.

RESULTS - In the first case, a 73-year-old female had an access site PSA off the superficial femoral artery (SFA) with concomitant arteriovenous fistula (AVF) and advanced cardiac disease. The ProGlide device was …

Low-Cost Cutaneous Protoporphyrin Ix (Ppix) Detection (Cpd) Device For Follow-Up Monitoring Of Patients After Photodynamic Therapy, Md Asaduzzaman Rasel

Graduate Masters Theses

Background: Photodynamic Therapy (PDT) utilizes specific wavelengths of light to activate photosensitizing chemical compounds, known as photosensitizers, which induce the generation of cytotoxic reactive oxygen species (ROS) for the targeted destruction of cancer cells. Among various photosensitizers for PDT, Protoporphyrin IX (PpIX) is widely employed in oncology and dermatology due to its natural in situ generation via the metabolic conversion of 5- aminolevulinic acid (ALA), a non-phototoxic prodrug. Systemic administration of ALA after 3-6 hr drug delay leads to peak PpIX accumulation in tissues, facilitating therapeutic and diagnostic applications. However, PpIX can persist in the skin for 24–48 hours post-treatment, …

Design And Development Of A Standalone Digital Holographic Microscope Employing Phase-Driven Reconstruction And Classification For Biomedical Imaging And Optical Diagnostics, Charlotte Kyeremah

Graduate Doctoral Dissertations

Access to advanced biomedical imaging technologies remains a significant challenge in resource-limited settings, especially for early disease detection and monitoring of diseases such as malaria, HIV, and other blood-borne diseases. Although point-of-care (POC) devices have gained popularity in global health, many rely on antibody-based tests, lateral flow strips, or optical readouts that often lack quantitative capabilities, sensitivity to early infections, or versatility in different diagnostic targets. In addition, these systems are typically dependent on disposable reagents or manual interpretation, which limits their effectiveness in remote areas. Digital Holographic Microscopy (DHM) presents a promising alternative as a label-free imaging method capable …

Predicting The Response Of Tendon-Driven Prosthetic Finger With Hyperelastic Joints, Lucas Gallup, Mohamed Trabia, Brendan O'Toole

Mechanical Engineering Faculty Research

Properly designed prosthetics hands can enhance the quality of life for those suffering from limb loss. Recently, 3D-printed prosthetic hands are becoming common. In these prostheses, fingers flex through the tendons that are activated by motion of the wrist. To provide spring action, thermoplastic polyurethane (TPU) hyperelastic joints are used to connect digits to each other as well as to the wrist. While these designs are common, no model for the relationship between tendon tension and joint flexion is available. This work has developed a quasi-static virtual work-based model to predict the relationship between tendon forces and the flexion of …

Functional Biopolymers Applied To Sustainable Technologies In The Environment And Healthcare, Fengjie He

UNLV Theses, Dissertations, Professional Papers, and Capstones

Biodegradable polymeric materials (biopolymers) are naturally derived materials known for their excellent biocompatibility, biodegradability, sustainability, and versatile chemical functionality. They have attracted increasing attention in various applications as alternative to synthetic materials ranging from food packaging to tissue engineering. Meanwhile, with intrinsic advantages, biopolymers have also emerged as promising materials in addressing contemporary challenges in both biomedical and environmental fields. Motivated by the significant potential of biopolymers and the growing need for sustainable materials, my research focuses on the design and engineering of biodegradable polymers with novel modification methods and application directions. In this work, two representative biopolymers are selected: …

Validity Of Body Composition Estimates In Women Assessed By A Multifrequency Bioelectrical Impedance Device, Mitchell Evan Zaplatosch, Juliana F. Meireles, Janeen S. Amason, Sadaf Dabeer, Brian M. Kliszczewicz, Gerald Mangine, Valene G. Barry, Barbara A. Gower, Katherine H. Ingram

Faculty Articles

Background: Multifrequency bioelectrical impedance devices such as the InBody 770 (IB770) offer faster measurements and lower costs compared with other body composition assessments. This study validated measures from IB770 against the deuterium oxide dilution technique (D2O) and DXA and compared a four-compartment (4C) model using total body water (TBW) derived from IB770 compared with D2O. Methods: A total of 55 adult females (mean ± SD, age: 21.1 ± 2.6 years) completed IB770 and DXA scans and the D2O protocol. Lin’s concordance correlation coefficients (CCCs), Bland–Altman analyses, and other equivalence tests evaluated agreement between IB770 and the criterion for measures of …

Fourier-Feature Mlp Toolkit For Gpu-Accelerated Cardiac-Mri 4dcmr Strain Analysis, Aarnav T. Sabale, Marco A. Prado, Craig J. Goergen

Discovery Undergraduate Interdisciplinary Research Internship

This paper explores the embedding of a Fourier-Feature—enhanced multiplayer perceptron(MLP-FEE) at the heart of a newly refactored python workflow for four-dimensional cardiac-MRI strain quantification demonstrating how a single, compact network can outperform traditional convolution and spline-based methods. The original code, capable of orientation normalization, displacement tracking, and finite-difference strain computation, has been translated and consolidated into pytorch. By injecting sinusoidal positional encodings at the network’s input layer supplied a rich set of high-frequency basis functions hence enabling multilayer MLP to resolve gradients that cubic splines and conventional CNNs typically blur or struggle with. Profiling on an Apple-silicon GPU shows interactive …

Advancing Single-Molecule Nanopore Sensing: From Protein Conformation And Metal Binding To Dna Transport Via Hybrid Nanostructures, Matthew J. Odonohue

Multidisciplinary Studies Theses and Dissertations

This dissertation presents the development and application of solid-state and hybrid nanopore platforms for single-molecule analysis of biomolecular interactions. First, a silicon nitride nanopore was employed to characterize the conformational states of the transferrin receptor (TfR), enabling discrimination between its monomeric and dimeric forms, as well as from its ligand, human serum transferrin (hSTf), despite their similar molecular weights. In a separate study, the same nanopore configuration was used to track the real-time binding of titanium ions to transferrin, demonstrating single-molecule sensitivity to metal-induced conformational changes. A hybrid microtubule–solid-state nanopore (MT–SSN) was then engineered, repurposing microtubules as electrostatically anchored conduits …

Volumetric Imaging Of Cellular Dynamics Using Light-Sheet Microscopy: From Subcellular Structures To Whole Organisms, Md Nasful Huda Prince

Optical Science and Engineering ETDs

Advancing biomedical imaging requires platforms that combine high-resolution, speed, and stability across biological scales. This dissertation presents three innovations designed to address limitations of conventional light-sheet and oblique plane imaging. First, we introduce Reflected Inline Detection in Epi-Oblique Plane Microscopy (RIDE-OPM), a compact and drift-resistant system that eliminates a tertiary detection path while maintaining alignment flexibility, enabling robust long-term live imaging. Second, we present a high-speed Axially Swept Light-Sheet Microscopy (ASLM) platform for cleared tissues, using dual foci and synchronized sweeping to achieve isotropic sub-micron resolution at up to 40 frames-per-second, a fourfold improvement over standard ASLM. Integrated with a …

Crevice Corrosion Mechanisms Of Cocrmo Alloys In Orthopedic Implants: Retrieval Analysis, Nano-Tribocorrosion And Cellular Responses, Hwaran Lee

All Dissertations

Mechanically assisted corrosion and non-mechanically (chemically) driven corrosion in modular junctions of orthopedic implants using cobalt-chromium-molybdenum (CoCrMo) alloys remain clinical concerns and may contribute to implant failure. The underlying corrosion mechanisms are not yet fully understood, leaving a critical research gap. We hypothesized that corrosion in modular junctions may be driven by aggressive local environments, including fretting, metal ion release (cobalt ion, Co²⁺), low pH and reactive oxygen species (ROS). This dissertation aims to (1) analyze corrosion modes and potential causes in modular junctions; (2) identify chemically driven corrosion modes on CoCrMo alloys using simulated inflammatory modular taper …

Vibration-Based Detection For The Monitoring Of Neonatal Bcpap Respiratory Support To Minimize Duration Of Disconnections, Kaitlyn G. Calabresi, Meera R. Bhat, Lavinia L. Kong, Eli J. Foster, Jonathan Wang, Sangeeta Koilada, Angela Mak, Aastha Kapadia, Niam Mohseni, W. Keith Leung, Suneetha Desiraju, Constanza Miranda

School of Medicine Faculty Publications

Bubble continuous positive airway pressure (bCPAP) is a minimally invasive respiratory support for neonates experiencing respiratory distress syndrome (RDS). It exerts continuous, oscillatory air pressure to encourage lung function and development. Neonates’ movement may cause disconnections at the nasal interface. These disconnections are characterized by the cessation of bubbling at the bCPAP respiratory circuit output and frequently go unnoticed until hypoxia develops. Common Neonatal Intensive Care Unit (NICU) bCPAP systems lack a built-in alarm or accessory device to monitor for disconnections. As a result, nursing personnel must exercise extreme caution utilizing current bCPAP procedure. If a neonate is disconnected, it …

Exploring The Effect Of Led-To-Photodetector Spacing On Subcutaneous Photoplethysmography For Continuous Blood Pressure Measurement, Dario Cabal, Brian Nguyen, David B. Green, Kevin Kilgore, Varun Thakkar, Michael J. Fu, Steve J. Majerus

Student Scholarship

Photoplethysmography (PPG) is widely used to measure heart rate, blood oxygenation, and more recently, blood pressure. Implanted PPG systems offer the possibility to measure similar real-time measures of cardiovascular health, however, the detection method may vary due to a lack of capillary vessels for PPG sensors to observe in muscle tissue. To improve volumetric blood detection in large muscles, without relying on the capillary density of skin, a flexible PPG sensor was developed. The sensor included multiple spacing of illuminating infrared (IR) light emitting diodes (LEDs) and a single IR photodetector. This arrangement was expected to enable detection of blood …

A Wearable-Based Approach To Spinal Posture Tracking And Assessment, Sydney Marie Sherman, Noah Jeffery

Biomedical Engineering: Graduate Reports and Projects

This paper describes the design, manufacturing, and testing of a novel spinal posture tracking wearable device with embedded sensors. Currently on the market, most of the spinal posture tracking devices only focus on one segment of the spine and therefore do not track the entirety of human posture. The objective for this project was to create a wearable device in the form of a “smart shirt” that offers insights into posture trends throughout the day by tracking the entire spine. To begin the project, multiple designs were developed for the sensor array and wearable materials. These concepts were compared against …

Ac Electric Fields Manipulate And Concentrate Dna Molecules On Electrodes, Akila Wijesinghe, Dharmakeerthi Nawarathna

Graduate Student Government Association Research Conference

Point-of-care (POC) electric field-based biosensors have emerged as a promising tool to detect early cancer biomarkers such as circulating tumor DNA (ctDNA), microRNA (miRNA), and proteins. To be effective in screening in clinical settings, these biosensors must be simple and easy to use. In this study, we have studied the manipulation of short DNA molecules suspended in a sessile drop to achieve this goal. Alternative current (AC) electric fields were used to polarize DNA molecules and produce dielectrophoretic (DEP) force on DNA molecules. DEP force is used to manipulate polarized DNA molecules towards the higher electric field gradients (toward the …

A Smart System For Detecting Anatomic And Histological Symptoms Of Diseased Agricultural Plants, Rustam Baratov, Himola Sunnatillayeva, Alimardon Mamatovich Mustafoqulov

Chemical Technology, Control and Management

This study describes a novel agricultural plant disease detecting smart system, capable of handling measured plant body parameters and images received by high resolution camera at the same time. The proposed plant disease detection method is based on evaluation of the signals received by measured and controlled plant body physical parameters like resistance, temperature and capacitance of the plant stem and image processing. An analogue plant model based on an electrical circuit with distributed parameters was developed. In addition, in the article the block diagram of the smart system for the early detection of plant diseases, the circuit diagram, its …

Advancements In Refreshable Braille Display Technology: A Comprehensive Survey, Maryam Etezad, Rajeev Joshi, Franceli L. Cibrian

Engineering Faculty Articles and Research

This paper provides a comprehensive mapping literature review of the advancements in refreshable Braille display (RBD) technology, which employs dynamically movable pins or dots to render Braille characters for individuals with blindness and visual impairment. This literature review, which includes 96 papers, aims to summarize the current evidence on six distinct types of RBDs: piezoelectric, electromagnetic, electroactive polymer (EAP), pneumatic, shape memory alloy (SMA), and microfluidic technologies. For each type, we discuss the underlying mechanisms, alongside the current trends and research opportunities. This comparative analysis aims to inform the selection of appropriate RBD technology based on specific user needs and …

Evaluation Of Antibiotic Testing Protocols For Biofilm-Forming Escherichia Coli In A Microfluidic Platform, Caleb R. Telander

Master's Theses

Catheter-associated urinary tract infections remain an ongoing clinical problem due to biofilm persistence and antibiotic resistance. Standard antibiotic susceptibility testing cannot accurately reproduce flow conditions and the spatial complexity of the in vivoenvironment and is thus questionable in relevance to device-related infections. This study examines a microfluidic device designed to simulate physiologically relevant wall shear stress and antibiotic gradients in Escherichia coli biofilms. The polydimethylsiloxane-based system integrates a 16-well culture chamber with a gradient generator. Biofilm growth was observed using fluorescence microscopy of green fluorescent protein-labeled bacteria. Simulations performed using COMSOL Multiphysics software estimated the appropriate range of wall …

Efficacy Of Monophasic And Biphasic Pulsed Field Ablation Waveforms: A Model Study, Natalia Dekock

Master's Theses

Cardiac arrhythmias are conditions where the heart’s normal sinus rhythm is interrupted by accelerated or premature rhythms. The most prevalent of these rhythms is atrial fibrillation (AF), where disorganized impulses cause the atria to quiver and pump blood inefficiently. As of 2025, AF affects over 10 million people. Aside from invasive surgical treatments, antiarrhythmic drugs, or one time cardioversions, atrial fibrillation is treated with catheter ablation. The longstanding ablation solutions for AF have been the cryoballoon or radiofrequency catheter ablation. However, limitations for these two ablation modalities are due to the nature of cell destruction; both thermal methods pose a …

Acoustic And Hemodynamic Analysis Of Phantoms: Roughness And Flow Dynamics, Ethan Erik Olof Sundberg

Master's Theses

The purpose of this study was to determine whether different vascular phantoms, with and without a surrogate arm, could serve as effective analogs to the human brachial artery for assessing endothelial dysfunction, an early indicator of cardiovascular disease, particularly atherosclerosis. Atherosclerosis is characterized by plaque buildup and endothelial damage, which precede more severe clinical events and are often detectable through changes in vascular function. A 40” water tower was used to simulate diastolic pressure, enabling water flow through each phantom. Strain gauge pressure transducers were placed at both ends of the phantoms to measure pressure drop, while a microphone captured …

A Manufacturing Process For Interdigitated Microelectrodes On Glass Wafers, Wyatt W. Warfield

Master's Theses

This study presents work done to optimize the process parameters to produce interdigitated electrodes on a borosilicate wafer. Using designed experiments and statistical analysis, the error in pattern transfer was minimized using for key process steps including exposure time, develop time and post exposure bake duration. Similarly, statistical analysis was used with profilometry data to fine tune the develop times. Qualitative analysis was used to assess thin film deposition. The resulting process produced wafers with improved pattern transfer and adequate film adhesion

Quantifying Harmful Trunk Postures: Inertial Sensor Analysis Of Trunk Angle To Support Low Back Pain Prevention, Elsa E. Bates

Master's Theses

Low back pain is a highly prevalent condition worldwide, impacting up to 80% of individuals at least once in their lifetime. A critical gap in current prevention strategies is the lack of tools to accurately measure trunk posture and movement in real-world environments. Accurate identification of biomechanical risk requires information about movement intensity, duration, and frequency, yet traditional assessment methods rely on self-reporting or visual observation, which are time-consuming and prone to error. To address this gap, a wearable monitoring method, consisting of two Inertial Measurement Units, was designed to quantify risk exposure to the spine by measuring angular position …

Biofeedback For Upper Limb Bionics, Arissa Anaya, Adam Moger, Connor Bly, Theodore R. Hughes

Biomedical Engineering

The purpose of this document was to present a senior design project from Cal Poly sponsored by Matt Robinson at the Hanger Clinic in San Luis Obispo to provide biofeedback for users of upper limb protheses. This project focuses on individuals with trans-radial upper limb amputations, including patients with congenital limb deficiencies who use trans-radial prosthesis, who receive very little or no sensory feedback from their prosthetic device. This sensory feedback device was intended to be used as a training tool with a myo-electric hand-like upper limb prosthesis in a clinical setting. This document provides an overview of the different …

Biostride - Prosthetic Charging Stand, Abigael Howard, Brett Matich, Allie Mcauliffe, Liam Harwood

Biomedical Engineering

This Final Report outlines the development of a lower limb prosthetic docking and charging station to address a critical need for individuals with unilateral transfemoral amputations who use microprocessor-controlled prosthetics. This project is focused on designing and producing a secure, accessible, and aesthetically pleasing stand to store and charge prosthetic limbs overnight, targeting the lack of commercially available, functional prosthetic storage. The absence of a functional storage solution points to a failure in meaningfully addressing the human needs of prosthetics users, exacerbating user frustration through the perpetuation of issues including prosthetics falling over into inaccessible positions, and tripping hazards due …

Force Mapping Wand For Individuals With Upper-Limb Amputations, Max Bosse, Cole Capitani, Eddie Grassini

Biomedical Engineering

Technology relating to upper-limb amputations has seen many advances in recent years, especially in terms of function and aesthetic appeal. Although these improvements exist, comfort is often a primary concern among prosthetic users and can lead to prosthetic abandonment [1]. Without a standardized method of measuring force concentrations in patients, high rates of discomfort and potential tissue damage remain. The goal of this project is to create a force mapping system for upper-limb amputees to help minimize discomfort in socket fit during the fitting process using real-time data and software to view force concentrations. To accomplish this goal, background research …

Hands-Free Balance Protocol And Development Of An Iphone App For Self-Assessment, Jacob Matties

Master's Theses

For many clinical populations, the measurement of balance is a critical task. Previous studies have agreed that smartphone IMUs provide a valid measure of balance that can be significantly correlated with force plate measurements and is sensitive enough to distinguish between various balance poses, but many balance assessment protocols require uncommon equipment or the use of hands during assessment. These limit accessibility of balance assessment. To eliminate the need for hands or any additional equipment, this study assessed the use of a smartphone recording the root mean square of 3D acceleration magnitude. The goal of the study was to determine …