Biomedical Devices and Instrumentation Commons^™

Design And Parametric Testing Of A Transimpedance Amplifier For Low-Power Biomedical Applications, Stanlon Tan, William Chung, Brandon Wu

Electrical Engineering

This project developed and evaluated an optical sensing system for detecting changes associated with glucose concentration. The system combined a laser-diode, cuvette sample holder, photodiode, resistive-feedback transimpedance amplifier, high-resolution analog-to-digital converter, and microcontroller. Parametric testing evaluated the effects of input current and feedback resistance on transimpedance gain, output range, and linearity. Firmware was developed to configure the ADC, average repeated conversions, monitor measurement variation, convert raw digital counts into voltage using a source-meter calibration equation, and compare sample measurements with a water reference. A cuvette enclosure maintained alignment between the laser-diode, sample, and photodiode while reducing external optical interference. Testing …

Implantable, Sensor-Embedded Vascular Graft Towards Wireless Monitoring Of Stenosis, Nnamdi Dike

LSU Master's Theses

Arteriovenous (AV) grafts are commonly used to provide vascular access for hemodialysis in patients with end-stage renal disease. Despite their widespread use, AV grafts are prone to complications such as stenosis and thrombosis. Early detection of these conditions remains challenging with current monitoring methods too costly or insufficient. This work presents the design, fabrication, and validation of an LC pressure sensor embedded within a model AV graft to enable real-time monitoring. The proposed system integrates a parallel-plate capacitive pressure sensor with a spiral inductor to form an LC circuit embedded within an elastomeric graft wall. The Ecoflex 00-30 dielectric layer …

Polymer Microstructures For Advanced Biomanufacturing, Tongyao Wu

LSU Doctoral Dissertations

With the continued growth of the biopharmaceutical industry, the demand for scalable, robust, and resource-efficient platforms for large-scale mammalian cell culture is amplified. Recent developments in microfluidic technology, such as precise control of the microenvironment, showed the potential to improve the performance of cell culture systems. However, constrained by scalability and operational efficiency, applying such approaches to large-scale cell culture and biopharmaceutical production presents challenges. This dissertation addresses these challenges through three independent but conceptually related technological developments. First, a roll-to-roll (R2R) fabrication process was developed for the scalable production of hollow microcarriers (HMCs). HMCs provide three-dimensional microenvironments suitable for …

A Smart System For Detecting Anatomic And Histological Symptoms Of Diseased Agricultural Plants, Rustam Baratov, Himola Sunnatillayeva, Alimardon Mamatovich Mustafoqulov

Chemical Technology, Control and Management

This study describes a novel agricultural plant disease detecting smart system, capable of handling measured plant body parameters and images received by high resolution camera at the same time. The proposed plant disease detection method is based on evaluation of the signals received by measured and controlled plant body physical parameters like resistance, temperature and capacitance of the plant stem and image processing. An analogue plant model based on an electrical circuit with distributed parameters was developed. In addition, in the article the block diagram of the smart system for the early detection of plant diseases, the circuit diagram, its …

Development Of A Portable Electroencephalogram With Display, Seth D. Davis

Electronic Theses and Dissertations

In this experiment, the goal was to design, build, and test an Electroencephalogram (EEG) circuit that would then be paired with a touchscreen display as a portable unit for use in Schizophrenic research at East Tennessee State University at the Quillen College of Medicine. The requirements for this prototype denoted that the device had to be able to obtain a signal from two electrodes placed on the head of an individual with a third attached to the ankle as a ground, amplify and filter the signal, and display the results on a touchscreen display for recording and analyzing. The circuit …

Dual Base Sige Is-Hbt For Use In Biosensing Applications, Liam Stephen Hayes

Master's Theses

The proposed research is for a novel SiGe-based Ion-Sensitive Dual Hetero-junction Bipolar Transistor (IS-HBT) to be used in both trans-dermal biological sensing as well as Lab-on-Chip (LOC) applications. The end goals for the device designed are two: For one, the research done for this work will be used to substantiate the claims made by Zafar et al. [1] that an HBT-style structure is better suited for biosensing application rather than a conventional Field Effect Transistor (FET) based geometries. Secondly, it provides the final element to be integrated along with a selectivity membrane, as well as with a reverse-iontophoresis system to …

Design Of A Portable Fast Scan Cyclic Voltammetry Device Utilizing Pulse Width Modulation For Waveform Generation, Nora Szymkowski

Masters Theses

Fast Scan Cyclic Voltammetry (FSCV) is a widely used electrochemical technique for real-time measurement of the brain’s chemical messengers, including the molecule dopamine, with high temporal resolution. Currently the financial burden of performing FSCV is quite high, ranging from $8,000 to $20,000+ making the barrier to entry nearly insurmountable for laboratories and classrooms at small institutions. The purpose of this project was to develop a Do-It-Yourself (DIY), portable, and cost-effective FSCV system for use in laboratory and classroom settings. The project aimed to create a compact and cost-effective system that could be used by researchers and educators to study dopamine …

Shape Memory Alloy Capsule Micropump For Drug Delivery Applications, Youssef Mohamed Kotb

Theses and Dissertations

Implantable drug delivery devices have many benefits over traditional drug administration techniques and have attracted a lot of attention in recent years. By delivering the medication directly to the tissue, they enable the use of larger localized concentrations, enhancing the efficacy of the treatment. Passive-release drug delivery systems, one of the various ways to provide medication, are great inventions. However, they cannot dispense the medication on demand since they are nonprogrammable. Therefore, active actuators are more advantageous in delivery applications. Smart material actuators, however, have greatly increased in popularity for manufacturing wearable and implantable micropumps due to their high energy …

Smart Cushion Device For Elderly Aging In Place, Anna Dion, Nate Colley, Leonardo Bravo

Biomedical Engineering

Our task at hand is to develop a consumer-focused solution for improving elder care to provide additional peace of mind for seniors and caregivers using technology to extend independent living. We intend to create a device that will improve the quality of life of elderly individuals living alone by encouraging periodical movement throughout the day, along with monitoring pressure distribution and alerting when pressure concentration is potentially harmful. It will also alert users to the presence of moisture which can arise from spills or incontinence. The key stakeholders of this project include elderly adults over the age of 65 who …

2-Channel Eeg Neurofeedback System, Tim Erwin, Donna Nikjou, Sebastian Turkewitz

Electrical Engineering

This work describes the design of an EEG-based neurofeedback system which provides users with real-time feedback on their level of focus or relaxation. By analyzing the spectral content of the brain activity measured via scalp electrodes, focus and relaxation levels can be quantified. Based on these measurements, live feedback in the form of moving bar graphs is provided to users, allowing them to gain awareness of their mental-state and more efficiently learn how to consciously relax or focus. This project covers the design of the system, including amplification and filtering stages, digitization, and signal processing. The system interfaces with a …

Database And Machine Learning Model For Classifying Autism Spectrum Disorder From Smartphone Based Electroretinography, Rory Harris

Honors Scholar Theses

Autism Spectrum Disorder (ASD) is a neurodevelopmental disorder that negatively affects a patient’s cognitive and communication aptitude and, therefore, can severely impact that patient’s quality of life. Because of this, early diagnosis is paramount. In recent studies, electroretinography (ERG), which is a measure of the retina’s electrical response to a brief flash of light into the eye, has shown promise in detecting ASD. Access to these scans can provide early diagnosis, improving well-being. Current ERG devices are very expensive due to their on board processing capabilities. This paper aims to create an ERG device using a smartphone as the main …

Towards A Wearable Device For Measuring Impedance Plethysmography Of The Radial Artery, Pritom Chowdhury

Dartmouth College Master’s Theses

Recent advancements in bioimpedance technology have demonstrated significant promise in the application of cardiac health monitoring. This research explores the design and development of a forearm-based wearable bioimpedance device for non-invasive measurement of heart rate and respiratory rate at an accuracy level comparable to medical-grade monitors. It utilizes a tetrapolar electrode configuration to analyze bioimpedance changes in the radial artery due to blood flow.

An ongoing aspect of this work involves the preliminary development of an embedded framework intended to integrate signal generation, acquisition, and processing within the device to achieve compact and efficient system design, anticipated to contribute to …

Development And Application Of Guided Mode Resonance Biosensor Platforms For Highly Sensitive And Real-Time Cell Killing Assays, Seyedmohsen Vaziri

Electrical Engineering Dissertations - Archive

In this work, we developed and investigated the cancer cell killing efficacy of different instances using real-time high-sensitivity measurements facilitated by Guided-Mode Resonance (GMR) sensors. The GMR biosensor technology detects shifts in the spectral peak caused by changes in the refractive index of the surrounding medium, offering a label-free method for monitoring cellular events.

A549 cell line wild type and HER2 knockout (lung cancer cells) were exposed to different concentrations of Triton X-100 and ADC (Herceptin with αHFc-CL-DMDM). The GMR-based cell killing assay demonstrated exceptional sensitivity and specificity, with shifts in wavelength exhibiting a robust correlation with cell viability and …

Non-Invasive Monitoring Device For Early Detection Of Breast Cancer Related Lymphedema, Amy Prendergast

Honors Theses and Capstones

Breast Cancer Related Lymphedema (BCRL) is a common co-morbidity in cancer survivors following neoadjuvant therapies such as chemotherapy, radiation, and/or surgery. It is brought about by the disruption in the lymphatic system (think lymph node biopsy) that leads to a buildup of lymphatic fluid in the arm. Current diagnostic strategies for this condition are merely retroactive, and fairly limited in the parameters that are examined to ensure patient well-being long term. We hypothesize that with an approach that mimics bioimpedance spectroscopy analysis, we will be able to provide a clinical support tool that would better determine early stages of lymphedema …

A Novel Brain Computer Interface Design, Steven Vogan

Senior Honors Theses

A brain computer interface (BCI) is a system which connects neural signals to a computer system. They have been used for controlling systems including robotics, on-screen computer control such as mouse movement, typing, and synthesizing audio signals. Invasive, or implanted, systems are often long-term medical solutions, or used for research where very clear signal is required. Non-invasive systems usually rely on exterior signals gathered through a headset using one or more electrode sensors. These signals are composed of sums of neuron activation potentials from brain activity and can be used to determine particular aspects of brain function. All BCIs rely …

Design Of Asic Based Electrical Impedance Tomography Microendoscopic System For Prostate Cancer Surgical Marginal Assessment, Mohsen Shahghasemi

Dartmouth College Ph.D Dissertations

Prostate cancer is the second most common cancer in the United States. It is typically treated by surgically excising the cancerous section of the prostate. Because there is not always a visible distinction between the healthy and cancerous sections, surgery often leaves some cancerous tissue behind. This is referred to as a positive surgical margin and it requires adjuvant treatment with adverse side effects. Electrical impedance tomography (EIT) is a low-cost low-form-factor method that can be used to assess surgical marginal intraoperatively to ensure that no cancerous tissue is left behind. EIT-based surgical margin assessment works on the principle that …

Characterization And Estimation Of Musculoskeletal Pain Using Machine Learning, Boluwatife Faremi

Master's Theses

Traditional scales utilized for recording pain are known to be highly subjective and biased due to inaccuracies in recollecting actual pain intensities. As a result, machine learning (ML) models that are trained using these scores as ground truth are reported to have low performance for objective pain classification because of the huge disparity between what was felt in moments of pain and the scores recorded afterward.

In the present study, two devices were designed for gathering real-time, continuous in-session subjective pain scores and the recording of the autonomic nervous system (ANS) altered endodermal (EDA) activity. 24 participants were recruited to …

The Study Of Corrosion On Additive-Manufactured Metals., Braydan Daniels

Electronic Theses and Dissertations

The purpose of this study was to investigate and compare the corrosion mechanisms between wrought and additive-manufactured (3D-printed) copper and stainless steel. The experimental procedure consisted of measuring the open circuit potential, electrochemical impedance spectroscopy, linear sweep voltammetry, Tafel analysis, surface topology, and scanning electron microscopy for each metal within salt water, tap water, sulfuric acid, and synthetic body fluid (excluding copper in synthetic body fluid).

Overall, printed stainless steel was more corrosion-resistant than wrought stainless steel in tap water and synthetic body fluid based on OCP, LSV, and surface topology results. Additionally, printed copper was more corrosion-resistant than wrought …

Design And Fabrication Of A Force-Displacement Control Mechanism For Bone-Surgical Tool Testing, Kenneth Nwagu

College of Graduate Studies: Theses & Dissertations

This project focuses on the design and fabrication of an experimental setup for orthopedic-tool testing, tailored for a surgical instrumentation company. The multifaceted project encompasses a literature review, conceptual design, prototyping, and rigorous testing, resulting in a versatile control system capable of assessing various orthopedic tools, including bone drills, saws, burrs, and power handpieces.

Orthopedic surgical procedures (which include cutting and/or drilling into bone) often need to be performed on bones for faster recovery. The drilling and cutting process can cause an increase in temperature at the cutting site which can cause bone necrosis. The tools also need to be …

An Integrated Electronic-Skin Patch For Real-Time And Continuous Monitoring Of A Panel Of Biomarkers Combined With Drug Delivery, Tanzila Noushin

Electrical Engineering Theses

Inflammatory biomarkers present in the human body play a vital role in medical field by guiding the clinician in decision-making for many diseases. The levels of these inflammatory biomarkers are associated with the severity and progress of several diseases. Researchers have found that increasing severity of many diseases such as cardiovascular disease, after surgery infection, and adverse clinical outcomes due to infectious diseases, results in the elevation of the level of inflammatory biomarkers in human sweat. Furthermore, the inflammatory cytokines indicate the pathophysiology and prognosis of critically ill SARS‑CoV‑2 patients. In this thesis work, different sensors have been developed for …

Hypoxic Incubation Chamber, Simone Lisette Helfrich, Makenzie Nicole Jones

Biomedical Engineering: Graduate Reports and Projects

This paper describes the design, manufacturing, and testing of a novel controllable hypoxic incubator with fully functional oxygen gas control and temperature control in a humid environment. On the current market, a majority of the few hypoxic incubators use pre-mixed gas that does not offer precise control over gas concentration. The objective for this project was to create a chamber that allows the user to set the O2 concentration to varying set points of % O2 while maintaining the chamber at a constant body temperature, CO2 level, humidity, and sterility. To start the project, multiple concepts were developed for the …

Hypoxic Incubation Chamber, Simone Lisette Helfrich, Makenzie Nicole Jones

Master's Theses

This paper describes the design, manufacturing, and testing of a novel controllable hypoxic incubator with fully functional oxygen gas control and temperature control in a humid environment. On the current market, a majority of the few hypoxic incubators use pre-mixed gas that does not offer precise control over gas concentration. The objective for this project was to create a chamber that allows the user to set the O2 concentration to varying set points of % O2 while maintaining the chamber at a constant body temperature, CO2 level, humidity, and sterility. To start the project, multiple concepts were developed for the …

Insole Fall Prevention Device, Nick M. Hughes, Andrew M. Slaboda

Biomedical Engineering

Falls among the aging population occur every single day, with 1 in every 5 resulting in some injury and 300,000 hospitalized every year with a hip fracture [1]. The most popular and effective way to mitigate these falls is through physical therapist intervention. However, with the increased popularity in telerehab, many patients at risk for falls cannot accurately convey their gait tendencies to their physical therapists from the comfort of their home or while not in direct contact with the PT. A device like an insole, implanted with force sensors, which measures different parts of a patient’s foot, could convey …

Integration Of Electrical Impedance Spectroscopy For Multichannel Cell Culture Measurement, Conard Chan

Master's Theses

ELECTROCHEMICAL IMPEDANCE SPECTROSCOPY (EIS) has been widely used to study the electrical properties of biological material due to its non-invasive nature and experimental reliability. However, most of the precision impedance analyzers used in EIS only provide single- or two-channel measurements which are inadequate for larger-scale multiplexed measurements, such as those found in modern microfluidic cell culture experiments. The Biomedical Microsystems Laboratory has developed a 16-channel cell culture platform with integrated electrode arrays for monitoring cell growth and electrical properties (i.e., the so-called “electrical phenotype”). In this paper, a system consisting of a 16-channel solid-state analog multiplexer (MUX)paired with a low-cost, …

Experimental And Analysis Of Electromagnetic Characterization Of Biological And Non-Biological Materials In Microwave, Millimeter-Wave, And Terahertz Frequency Bands, Nagma Vohra

Graduate Theses and Dissertations

The goal of this research is to characterize the electromagnetic properties of biological and non-biological materials at terahertz (THz), millimeter-wave, and microwave frequency bands. The biological specimens are measured using the THz imaging and spectroscopy system, whereas the non-biological materials are measured using the microwave and millimeter-wave free-space system. These facilities are located in the Engineering Research Center at the University of Arkansas. The THz imaging system (TPS 3000) uses a Ti-Sapphire laser directed on the photoconductive antennas to generate a THz time domain pulse. Upon using the Fourier Transform, the spectrum of the pulsed THz signal includes frequencies from …

Portable Ventilator, Bradley C. Weeks, Jack W. Brewer, Sanders Sanabria

Electrical Engineering

The current COVID-19 pandemic has heavily impacted the healthcare system in the United States and elsewhere. The need for patients to have access to a hospital with a ventilator along with a shortage of ventilators for recovery and at-home care as a result of minimal hospital vacancy for patients has been greatly stressed. The presented problem is both an unmet demand and supply of portable and effective ventilators. Existing ventilators have many shortcomings that should be addressed: size, weight, cost, and complexity of current ventilators confines users to stay in a medical facility whilst being monitored by professionals. This both …

Error Prevention In Sensors And Sensor Systems, Pedro J. Chacon Dominguez

LSU Doctoral Dissertations

Achievements in all fields of engineering and fabrication methods have led towards optimization and integration of multiple sensing devices into a concise system. These advances have caused significant innovation in various commercial, industrial, and research efforts. Integrations of subsystems have important applications for sensor systems in particular. The need for reporting and real time awareness of a device’s condition and surroundings have led to sensor systems being implemented in a wide variety of fields. From environmental sensors for agriculture, to object characterization and biomedical sensing, the application for sensor systems has impacted all modern facets of innovation. With these innovations, …

Nitinol Robotic Arm, Brandon Cousino, Connor Sweatt

Thinking Matters Symposium

The goal of our project is to create a remotely controlled robotic arm using a nickel-titanium alloy (Nitinol) that exhibits “shape memory” tendencies and a 9-lumen tube. The arm must be able to move in all for directions (forward, left, right, backwards) with the control of a joystick and return to an upright position upon halting user input (thus requiring a two-way shape memory ability). The final product must operate without any unwanted twisting of the arm, crosstalk between the different nitinol wires due to heating, and be easily manufacturable. Easy replacement of the arm from the main mechanism is …

Heel Down And Toe-Off Time Measured With Ultrasonic Doppler System And Force Plate Sensor, Sabin Timsina

Honors Theses

Collie Box is a medical device that measures the gait parameters of the person walk- ing in front of it. This device uses the Ultrasonic Doppler system to extract the heel-contact and toe-off times of a person walking within the range of 2-10 meters. These times are used to determine the leg’s swing phase and double stance times. The ultrasonic transducer of 10mm diameter is driven at 40kHz. At the time of the heel-contact and toe-off, foot velocity is zero while the torso part of the human body is still in motion. The wide directivity of 10mm diameter ultrasonic transducer …

Neurostimulator With Waveforms Inspired By Nature For Wearable Electro-Acupuncture, Jose Aquiles Parodi Amaya

LSU Doctoral Dissertations

The work presented here has 3 goals: establish the need for novel neurostimulation waveform solutions through a literature review, develop a neurostimulation pulse generator, and verify the operation of the device for neurostimulation applications.

The literature review discusses the importance of stimulation waveforms on the outcomes of neurostimulation, and proposes new directions for neurostimulation research that would help in improving the reproducibility and comparability between studies.

The pulse generator circuit is then described that generates signals inspired by the shape of excitatory or inhibitory post-synaptic potentials (EPSP, IPSP). The circuit analytical equations are presented, and the effects of the circuit …