Heat Transfer, Combustion Commons^™

A Review Of Nano And Microscale Heat Transfer: An Experimental And Molecular Dynamics Perspective, Samyabrata Chatterjee, Paras, Han Hu, Monojit Chakraborty

Mechanical Engineering Faculty Publications and Presentations

Significant progress in the development of micro and nanoscale devices has been observed for the past three decades. The thermal transportation in these small-length scales varies significantly, and it is difficult to explain the underlying physics using the pre-existing theoretical formulations. When the bulk dimension of a system is comparable to or smaller than the mean free path (MFP) of the thermal carriers, classical theories, such as Fourier’s Law of heat conduction, are unable to accurately explain the system energy dynamics. The phenomena of energy transit and conversion at the micro to nanoscale is an interesting topic of research due …

Accomplishments Of Endwall Contouring On Heat Transfer In A Passage Of A Turbine Blade, Kozhikkatil Sunil Arjun, Tide Porathoor Sunny, Narayanan Biju

Makara Journal of Technology

The study explores axisymmetric endwall contouring with emphasis on the design of novel endwalls capable of heat load reduction. Optimizations with parameterization numerically determined by the endwall of flat shape led to the endwall of the contoured shape with substantial depletion of heat transfer in the passage of the vane. Heat transfer attributes for the generated contoured endwalls were analyzed for the exit Reynolds number of 2 × 106 . Endwall three-dimensional contouring resulted in remarkable changes in secondary flow vortices, jet-to-secondary flow interaction, and film cooling effectiveness on the flat endwall. The results pointed out that the axisymmetric convergent …

Modeling Of Heat And Mass Transfer In Flat Heat Pipes, Salar Saadatian

LSU Doctoral Dissertations

Phase-change phenomenon is ubiquitous in nature and widely utilized in thermal management of computer chips. Flat heat pipes have been extensively used in thermal management of microelectronic devices. However, existing research mainly concentrates on developing numerical models and lacks a systematic analytical approach to elucidate the working mechanism of flat heat pipes. We consider a horizontal flat heat pipe with an idealized porous wick. The pores in the wick are straight circular capillaries running along and across the wick and are filled with a liquid. The rest of the pipe is filled with its vapor. The mass evaporative rate at …

Experimental Analysis On Effects Of Inclination And Direction On Supercritical Carbon Dioxide Heat Transfer For Internal Pipe Flow, Emmanuel Gabriel-Ohanu

Electronic Theses and Dissertations, 2020-2023

Supercritical carbon dioxide (sCO2) can be utilized as a working or heat transfer fluid in various thermal systems with applications in large-scale power cycles; portable power production units, coolant systems and devices. However, there are no sufficient methods and equations of heat transfer coefficient correlations, and in addition insufficient research studies about the mechanisms controlling heat transfer processes for sCO2. This study is motivated by the need to understand the intricate properties of sCO2 heat transfer and fluid dynamics with an emphasis on flow direction and inclination effects. This paper presents the study on effects of gravity, buoyancy on sCO2 …

Heat And Mass Transfer Modeling Of High-Temperature Moving-Bed Thermochemical Reactors, David Korba

Theses and Dissertations

With the global deployment of renewable energy generation at record rates, clean energy is steadily becoming competitive with its fossil-fuel counterparts. However, further expansion is limited by the inherent intermittency of renewable energy sources (solar, wind, wave, etc.), which typically do not match with daily and seasonal variations of global (and local) energy demand. Thermochemical energy storage (TCES) has demonstrated strong potential in being a technological pathway to provide on-demand process heat and handle the intrinsic variations in renewable energy generation and energy demand. TCES works on the premise of excess renewable heat driving an endothermic reduction reaction, in which …

Performance And Emissions Study Of N+3 And N+4 Engine Models With Several Fuel Types Using Npss, Abel Solomon

McKelvey School of Engineering Graduate Student Theses & Dissertations

The aviation industry is known to be one of the major contributors to greenhouse gases accounting for 4.9% of the global greenhouse emissions. With the ever-increasing threat of climate change to the overall survival of the planet, the exploration of new technologies and alternative energy sources that minimize greenhouse gas emissions are of paramount importance. In this regard, the development of propulsion systems well suited for the performance and emissions requirements of future commercial aircraft plays a crucial role. This thesis investigates N+3 and N+4 technology-level propulsion systems that are proposed by NASA as possible propulsion systems for advanced single-aisle …

Applications Of Large Eddy Simulations To Novel Internal Combustion Concepts, Patrick O'Donnell

All Dissertations

Computational fluid dynamics (CFD) simulations of internal combustion engines (ICEs) are becoming an increasingly popular tool in the automotive industry to either explain experimentally observed trends or perform lower cost design iterations. The convenience of commercially available CFD software and advancements made in computing hardware have been the impetus behind this growing popularity. However, obtaining accurate results using these software packages is not a trivial process and requires an in-depth understanding of the underlying numerical methodology and sub models for various physical phenomena. Specific to the ICEs, CFD simulation often entails the use of models for detailed chemistry and combustion, …

Measurement Of Conduction, Radiation, And Convection Thermal Energy To Assess Baking Performance In Residential Ovens., Sean Simpson

Electronic Theses and Dissertations

Residential ovens are complicated thermal environments capable of delivering convection, conduction, and radiation heat transfer to food. The amount and mode of heat transfer can change based on the design of the oven cavity, cooling systems, and oven cycle algorithms. Studies have shown that the changes in one heat transfer mode can have an impact on the quality of baked goods. The many variables involved make designing residential ovens a time consuming and costly process. The goal of this study is to adapt thermal energy sensing technology to collect energy data from a residential oven and develop correlations to quality …

Healthcare Built Environment And The Covid-19 Pandemic, A Mixed-Method Study, Mohammad Saleh Nikooopayan Tak

All Theses

The outbreak of COVID-19 presented an unparalleled risk to public health, leading to urgent scientific efforts in understanding transmission mechanisms and mitigating risks, especially in healthcare settings. This mixed-methods study examines knowledge advancement regarding indoor air quality in healthcare facilities during the pandemic. A systematic literature review of 163 post-COVID studies identifies key research thrusts and 31 recommendations related to building ventilation, air filtration, surface disinfection, and monitoring. Comparison with over 200 pre-pandemic publications reveals both reliance on established infection control principles and unique contributions, such as detecting viral RNA in air and surface samples indicating potential airborne and fomite …

The Influence Of Mixing Duct Length And Phase Of Flight On Wall Temperatures Of A Rocket Based Combined Cycle Engine In Ejector And Air-Augmented Modes, Jonathan Grow

Doctoral Dissertations and Master's Theses

Rocket Based Combined Cycle (RBCC) engines have been theorized as a possible means of powering launch vehicles and high-speed atmospheric vehicles. By incorporating aspects of both air-breathing and rocket propulsion, RBCC engines promise up to a 230 % increase in specific impulse over traditional chemical rocket propulsion by entraining a secondary flow of atmospheric air and mixing it with the exhaust of a rocket motor. Students within the Embry-Riddle Future Space Explorers and Developers Society (ERFSEDS) identified a
problem of excessive heating and structural failure of the mixing duct during launch and transonic flight of a student-built flight test vehicle. …

Advances In Spacecraft Thermal Control, Sandra K. S. Boetcher, Robert C. Consolo Jr.

Publications

Spacecraft thermal management is critical for ensuring mission success, as it affects the performance and longevity of onboard systems. A comprehensive overview of the state of the art in spacecraft thermal control solutions, as well as a design methodology framework for efficient and effective thermal management, is provided. Various thermal control solutions, including coatings, insulation, heat pipes, phase-change materials, conductive materials, thermal devices, actively pumped fluid loops, and radiators, are discussed along with the primary sources of heat loading in space. The need for accurate modeling and analysis of the thermal environment to identify appropriate thermal control solutions and design …

Addressing Low Heat Pump Heating System Sales In The Uk, Ben Costelloe

Articles

The replacement of existing fossil fuel boilers with heat pumps is seen as a key measure in the decarbonisation of heating systems and addressing climate change. This policy however, is currently failing in many Western European states, particularly in the UK. The many reasons for this situation are examined. However, the age of UK housing stock and particularly the high number of dwellings built prior to the introduction of building insulation regulations in 1980, are key. To maintain the running cost of air source heat pumps competitive with those of the gas boilers they generally replace the heat pump lift …

Flat Plate Solar Collector For A Tiny Home, Clarice Leslie Nicholas

Honors Projects

Pallet Shelter is a company that builds tiny houses for the homeless. We partnered with them to build a solar water heater for their homes so that their tenants can have hot running water. The collector panel sits on the roof of the shelter and absorbs the energy of the sun and uses it to heat water flowing through an array of copper pipes. The hot water is then stored in an insulated tank inside the shelter.

Cooled Liquid Rocket Thrust Chamber, Benjamin Gibson, Kealan Frederick Harris, Ryan Frank Schackel, Bjorn Thorsen

Mechanical Engineering

Cooling may affect the thrust output of a small-scale rocket. Little research is published about small-scale rocket performance. We hypothesize the thrust produced varies as the amount of cooling varies. To facilitate assessing this hypothesis, we have designed and built a liquid rocket engine rated for at approximately 25 lb_f of thrust. Our objective was to build in parallel with Cal Poly Space Systems, who built a rocket engine with similar specifications except without cooling. Our challenge is to integrate film cooling, so that the effects of cooling may be compared to Cal Poly Space System’s engine which has …

Flexible Water Cooling, Joshua Terlaje, Andrew Lin, Nicholas Morales, Tanner Parrott

Mechanical Engineering

The goal of this project is to develop and deploy a water-cooling system to reduce the danger of heat exhaustion among communities of farmworkers. Currently, it is difficult to keep chilled water available throughout the workday when using portable water coolers. The idea uses a refrigeration system to chill the water supply by using the power take-off (PTO) on farm equipment and a corresponding generator to get around this restriction.

The project places a strong premium on keeping the chilled water supply at a maximum temperature of 59°F to ensure compliance with the California Department of Industrial Relations' requirements. Each …

Statistical Uncertainty Of The Ignition Time, Burning Rate, And Extinction Characteristics Of Engineered Timber Products, Jacob David

Master's Theses

The characterization of flammability parameters such as time to ignition, mass loss rate (MLR), and extinction criteria is critical for understanding ignition and burning behavior of timber products. These parameters, often determined with bench scale experiments, have previously been presented in literature. However, standard test methods generally use relatively low trial quantities (e.g., n=3) which can potentially cause large variation in reported values. This study investigates the influence of trial quantity on observed statistical variation in key flammability metrics for timber products (e.g., ignition time, peak MLR, MLR at extinction). Using a conical heater, 100 repeat trials were conducted …

Thermal Transport And Physical Characteristics Of Silver-Reinforced Biodegradable Nanolubricant, Jaime Taha-Tijerina, Karla Aviña, Nicolás Antonio Ulloa-Castillo, Dulce Viridiana Melo-Maximo

Informatics and Engineering Systems Faculty Publications

In this investigation, the thermal transport behavior of biodegradable lubricant reinforced with silver nanostructures (AgNs) at various filler fractions of 0.01, 0.05, 0.10, and 0.20 weight percent was evaluated over a temperature scan analysis, ranging from room temperature up to 60 °C. The experimental results revealed significant gradual enhancements in thermal conductivity as AgNs concentration and evaluating temperatures were increased. These improvements showed the important role of nanostructures’ interaction within the biodegradable lubricant. The thermal conductivity performance improved for nanolubricants ranging from 6.5% at 30 °C and 0.20 wt.% AgNs content up to a maximum 32.2%, which was obtained at …

Atmospheric Carbon Capture: A Review On Current Technologies And Analysis Of Energy Consumption For Various Direct Air Capture (Dac) Systems, Jennifer Perskin

Doctoral Dissertations and Master's Theses

Carbon dioxide (CO₂) capture is a crucial approach to reducing greenhouse gases in the atmosphere to directly combat climate change. Major components of the technology to desublimate CO₂ at cryogenic temperatures are mature and have the potential to be applied to build large Arctic/Antarctic direct-air CO₂ capture plants. Pressure swing adsorption another gas separation technique used in industry today that can be modified for atmospheric carbon capture. The discussion of energy consumption for cryogenic and combined direct air capture systems is explored in this study. The investigation of precompression of atmospheric air for a direct-air capture …

Classification Of Electrical Current Used In Electroplastic Forming, Tyler Grimm

All Dissertations

Electrically assisted manufacturing (EAM) is the direct application of an electric current to a workpiece during manufacturing. This advanced manufacturing process has been shown to produce anomalous effects which extend beyond the current state of modeling of thermal influences. These purported non-thermal effects have collectively been termed electroplastic effects (EPEs).

While there is a distinct difference in results between steady-state (ideal DC) testing and pulsed current testing, the very definition of these two EAM methods has not been well established. A "long" pulse may be considered DC current; a "short" pulse may produce electroplastic effects; and even "steady-state" current shapes …

A Systematic Study Into The Design And Utilization Of Burn Wire As A Means Of Tensioning And Releasing Spacecraft Mechanisms Through Applied Joule Heating, Chandler Dye

Mechanical Engineering Undergraduate Honors Theses

The joule heating characteristics of Nichrome burn wires, often used as a thermal cutting device in mechanisms designed to fasten and release CubeSat deployables, are examined in the following thesis. Wires ranging from 0.125 inches to 2 inches long, and diameters of 30 Ga and 40 Ga, are investigated through analytical calculations and thermal simulations based on heat transfer due to joule heating, and through physical circuitry-based experiments. The temperature data is used to generate heating curves to predict the time it takes for Nichrome wires to fail under varying testing parameters. This research aims to catalog a series of …

Reynolds-Averaged Navier-Stokes Cfd Simulation Of High-Speed Boundary Layers, Michael Tullis

Mechanical Engineering Undergraduate Honors Theses

This paper presents an investigation of Reynolds-averaged Navier-Stokes (RANS) turbulence models used in computational fluid dynamics (CFD) simulations of boundary layer flow and heat transfer in high Mach number flows. This study evaluates an industry standard RANS turbulence model (k-omega SST) and a recently proposed modification to that model (Danis and Durbin [1]), and quantifies the accuracy for predicting high Mach number boundary layer flow. The test cases were previously documented by Duan et al. (2018), who used direct numerical simulation (DNS) to calculate boundary layer flow of an ideal gas over a flat plate at freestream Mach numbers ranging …

Pla-S-Tech: Pla Sustainable Technology, Sean Sapper, Ryan Decarlo, Elle Whitney, Samantha Dombrowski, Dalton Prokop, Dominic Zaio, Tyler Stokes, David Deese, Blake Hengel, Yi Guo

Mechanical and Civil Engineering Student Publications

To recycle waste material produced by fused deposition modeling (FDM) 3D printers, a recycler was designed and manufactured to convert plastic scraps into usable filament. The device does so by breaking down plastic material to a uniform size with the shredder, melting and compressing these pieces into a cylindrical strand with the extruder, and wrapping this strand around a filament spool with the spooler. As the device is mostly made from commercially-available components, it is easily maintainable and user-serviceable, while also costing less than similar devices on the market.

Portable Drinking Water Cooler And Dispenser, Gustavo Hernandez-Lerena, Erik Torres, Caleb Francis Parham, Terry Leung

Mechanical Engineering

This document serves as the comprehensive report for the testing and building for the Portable Water-Cooling System by team AquaCool. Team AquaCool is comprised of four mechanical engineers with a passion to help the agricultural industry in their efforts to keep the health of the workers at their peak. The four engineers who partook in helping the farm workers are as follows: Caleb F. Parham, Erik Torres, Gustavo Hernandez-Lerena, and Terry Leung. To reduce the risk of heatstroke and other unwanted effects from the harsh working conditions during summer, a small and portable system was built to help in the …

Thermal Boundary Condition Effects On Local Supercritical Co2 Heat Transfer Trends In Tubes, Nicholas C. Lopes

Doctoral Dissertations and Master's Theses

Supercritical carbon dioxide (sCO2) is a promising heat transfer fluid for the refrigeration and power generation industries due to its unique thermal properties and low environmental impact. To understand it as an alternative to traditional working fluids, the thermophysical and heat transfer phenomena of sCO2 are often studied using simplified geometries (tubes). Focus has been placed on investigating averaged heat transfer trends under an array of flow conditions with either a constant wall heat flux, constant wall temperature, or conjugate thermal boundary condition. Less emphasis has been placed on studying local sCO2 heat transfer developments. Tubular sCO2 numerical models that …

Experimental And Numerical Analysis Of A Commercial Phase Change Material Melting At Different Inclinations, Andrew Heiles

Doctoral Dissertations and Master's Theses

The study of various phase change materials (PCM), experimentally and numerically, have been completed over the past several years to address their feasibility and potential when used in latent heat thermal energy storage (LHTES) systems for a variety of potential applications. Previous studies have investigated changes into the type of PCM used in the system as well as the system configuration, ranging from boundary conditions to internal and external geometries and orientations of the system. The present study focused on conducting experiments at different inclination angles and isothermal wall temperatures with the organic PCM PureTemp37, and continued with a numerical …

Additive Manufacturing For Phase Change Thermal Energy Storage And Management, Thomas B. Freeman

Doctoral Dissertations and Master's Theses

Phase change materials can enhance the performance of energy systems by time shifting or reducing peak thermal loads. Certain electronic devices such as batteries, laser systems, or electric vehicle power electronics are highly transient and require pulse heat dissipation. Heat sinks, or thermal management devices made of a phase change material can absorb large heat spikes while maintaining a constant temperature. Additive manufacturing techniques hold tremendous potential to enable co-optimization of material properties and device geometry, while potentially reducing material waste and manufacturing time. Recently, a few efforts have emerged that employ additive manufacturing techniques to integrate a phase change …

Precise And Analytical Calculation Of Interface Surface Area In Sharp Interfaces And Multiphase Modeling, Simon P. Shipkowski, Isaac Bernabe Perez Raya

Articles

Various kinds of Piecewise Linear Interface Calculations (PLIC) are commonly used in Computational Fluid Dynamics (CFD) for multiphase flows. Here, a new method is proposed to calculate the interface size for CFD simulations. This PLIC method with the modifier, Analytic Size Based [method], (PLIC-ASB), being that the calculation requires a symbolic equation and no approximation or numerical methods. The primary advantage of the PLIC-ASB is maintaining a sharp interface and providing for physics-based (not iterative or empirically derived factors) mass transfer due to the cell-by-cell accuracy. Along with the sharp interface, this method leads to precise interface displacements and suppresses …

Detonation Confinement In A Second-Generation Radial Rotating Engine, John T. Ursino

Theses and Dissertations

In recent years, Rotating Detonation Engines (RDEs) have been coupled with turbomachinery to harness the benefits of detonative combustion. A novel type of RDE, referred to as the disk or Radial RDE (RRDE), has been developed in pursuit of length and weight savings compared to a traditional annular flow RDE. This design includes a disk-shaped device within which reactants flow from the outer radius, detonate, and exit the inner radius. In this paper several modifications have been made to a previously tested RRDE to address issues that arose with the original design. The combustion chamber diameter has been increased to …

Biogas Combustion Characteristics In A Concentric Flow Slot Burner: Effects Of Co2 Concentration On Stability And Flame Structure, Maged Kiriakos

Theses and Dissertations

Biogas combustion is affected by the concentration of carbon dioxide. The successful applications of Biogas as a sustainable renewable alternative fuel produced from waste depend on its combustion stability, heat release, and pollution level. The aim of the current study is to apply new combustion technology and study the stability and combustion characteristics of natural gas with different percentages of carbon dioxide from 0 to 40% simulating biogas fuel. The stability characteristics and the temperature profiles of turbulent planar flames at different levels mixture inhomogeneity are investigated and presented in this work. The flames are created in a newly developed …

Jack And Alex Rc-Baja, Alex Vornbrock

All Undergraduate Projects

Teams of two mechanical engineering students were tasked with the construction of an RC Baja car qualified by the rules and regulations of the Baja competition as well as specifications set by the individual team member for their portion of the vehicle. This proposal focuses on the Chassis and Drivetrain of the vehicle while team member Jack Stutz oversaw the steering and suspension. Teams will compete against each other in various modes to determine the best vehicles of the competitors. The chassis was made of standard aluminum, the remaining parts made by the students were made with PLA; both materials …