Biomedical Devices and Instrumentation Commons^™

Design Of A Homeopathic Solution For Chronic Cough, Jacob Ziemke

Senior Honors Projects, 2010-2019

Chronic cough is most commonly defined as a cough that persists for more than eight weeks and is estimated to affect more than 30 million people in the United States at any given time. Diseases contributing to the onset of chronic cough include asthma, pulmonary fibrosis, lung cancer, postnasal drip, gastroesophageal reflux disease (GERD), and bronchitis, and may include lifestyle choices such as smoking. For those who seek medical advice, pharmaceuticals and speech therapy are two common methods of combating chronic cough but serve to mask the symptoms rather than treat the problem; frequently, chronic cough is misdiagnosed or cannot …

Extraction And Analysis Of Vector Flow Imaging Data In A Pediatric Population, Bailey Stinnett

Biomedical Engineering Undergraduate Honors Theses

Vector flow imaging (VFI) is a new ultrasound technology that provides real time, angle-independent visualization of flow velocities in the heart and great vessels. Thus far, VFI has been used for superficial applications due to the limited penetration depth of available transducer probes; however, this depth in smaller pediatric patients enables adequate aortic views. In this project, VFI was used to study pediatric aortic stenosis (PAS)—a congenital heart defect that results in the narrowing of the aorta and/or aortic valve. The decision to refer PAS patients for surgical or catheter-based intervention is initially based on Doppler ultrasound. VFI is potentially …

Pressure Acquisition System For In Vitro Mitral Valve Analysis, Laura Peck

Biomedical Engineering Undergraduate Honors Theses

In vitro testing of the mitral valve chordae tendineae is utilized to aid in the understanding of the stresses that occur in vivo and improve upon surgical solutions that exist for mitral valve repair. This project aimed to design the water control system for a left heart simulation chamber, as well as the pressure acquisition inside the chamber. A solenoid valve was utilized to control the water supply to the tank and was powered utilizing National Instruments software. National Instruments hardware and software was also used with the pressure transducer in order to obtain pressure readings from the chamber. The …

Computational Fluid Dynamics Model For Air Velocity Through A Poultry Transport Trailer In A Holding Shed, Christian Heymsfield

Graduate Theses and Dissertations

Broiler production in Arkansas was valued at over $3.6 billion in 2013 (University of Arkansas Division of Agriculture Cooperative Extension Service). Consequently, improvement in any phase of the production process can have significant economic impact and animal welfare implications. One area of concern for the poultry industry is thermal stress experienced by the birds after arrival at the processing plant and before they are taken in to be processed, during which time they are left to wait in holding sheds. Various cooling strategies exist to mitigate heat stress in holding sheds, but in most cases it is unlikely that they …

Development Of A Novel Bioactive Glass Suitable For Osteosarcoma-Related Bone Grafts, Alireza Rahimnejad Yazdi, Lawrence Torkan, Stephen D. Waldman, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

In this study, zinc borate-based glasses with increasing gallium content (0, 2.5, 5, 10, and 15 wt % Ga) were synthesized and their effect on the viability and proliferation of preosteoblasts and osteosarcoma cancer cells were investigated. Methyl thiazolyl tetrazolium (MTT) cell viability assays using glass degradation extracts revealed that the extracts from glasses with lower Ga contents could enhance the viability of preosteoblasts, while extracts from the glass composition with 15 wt % Ga caused statistically significant reduction of their viability. MTT cell viability assays using the extracts and osteosarcoma cells showed that only extracts from the glass composition …

Ring And Peg Simulation For Minimally Invasive Surgical Robot, Evan Brown

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Surgical procedures utilizing minimally invasive laparoscopic techniques have shown less complications, better cosmetic results, and less time in the hospital than conventional surgery. These advantages are partially offset by inherent difficulties of the procedures which include an inverted control scheme, instrument clashing, and loss of triangulation. Surgical robots have been designed to overcome the limitations, the Da Vinci being the most widely used. A dexterous in vivo, two-armed robot, designed to enter an insufflated abdomen with a limited insertion profile and expand to perform a variety of operations, has been created as a less expensive, versatile alternative to the Da …

Investigation Of The Effects Of Prosthetic Knee Condition On Novice Transfemoral Amputee Runners, Natalie Nelson

Master's Theses (2009 -)

Some unilateral transfemoral amputees (TFAs) run in a prosthesis with an articulating prosthetic knee, others choose to run without a knee (prosthetic socket and foot are linked via a straight, non-articulating pylon) to increase stability. Research regarding unilateral TFA running with an unlocked versus locked prosthetic knee (approximately equivalent to the no-knee condition) with respect to energy cost and temporal metrics is limited; no studies have investigated the impact of knee condition on kinematic metrics. The purpose of this study was to investigate whether the prosthetic knee of a running-specific prosthesis (RSP) should be unlocked or locked for unilateral TFAs …

Design And Development Of A Multifunctional Surgical Device For Ground And Space-Based Surgical Applications., Brooke Elaine Barrow

Electronic Theses and Dissertations

With the possibility of longer ventures into space, NASA will face many new medical challenges. The ability to surgically treat trauma and other disorders in reduced gravity requires reliable wound access, containment, and visualization. In collaboration with Carnegie Mellon University, the University of Louisville is currently developing the AISS (Aqueous Immersion Surgical System) to increase efficiency and control of the operative field in space-based surgeries. Reliable wound access and containment is achieved by placing a transparent wound-isolation dome securely over the wound-site and pressurizing it with a saline solution. Leak-free trocars provide access ports for various surgical instruments. This system …

Development Of Rule-Based Recognition Systems For Continuous Monitorization Of Pulse Oximetry, Brian Delehanty

Senior Theses

Pulse Oximeters provide a convenient, non-invasive method to quickly gather information about a patient's pulse rate (PR) and arterial blood oxygen saturation (SpO₂). Many pulse oximeters lack alert systems that notify caregivers if a patient's readings go outside the healthy range, and pulse oximeters that have these mechanisms are significantly more expensive. This project set out to write a program using LabVIEW that collects pulse oximeter data via Bluetooth and generates an alert when readings persist in the abnormal range for more than fifteen seconds. Due to privacy laws that allow pulse oximeter manufacturers to not disclose the …

Optimization Of Microfluidic Chip Fabrication Via Femtosecond Laser Ablation, Kenneth Aycock

Senior Theses

Microfluidic devices have become staple tools in biomedical research and have a promising future as low cost, point-of-care (POC) diagnostic devices. Despite the advancements in microfluidic device technology, the manipulation and fabrication of these systems can be tedious and expensive. Repeatable techniques in which computer-aided designs are translated into microfluidic systems in a matter of minutes are highly desirable both for researchers and manufacturers. Laser ablation of tape substrates has shown promise in producing cost-effective, rapidly manipulable devices, but the work done thus far has utilized continuous wave lasers that perform suboptimally due to the relatively short wavelengths used and …

A Strategic Audit Of Medtronic Plc, Jozzy Carter

Honors Program: Senior Projects (Public)

Humans will always have a need for healthcare, and as the world continues to innovate in the tech space, consumers will demand advances in medicine and medical devices. Medtronic is at the forefront of this innovation but faces intense competition in the medical technologies industry. This poses the question: what can Medtronic do to continue its growth and stay competitive in this space? This paper offers an analysis of Medtronic as a medical device company by offering insight to its competitive advantage, financials, business mix, and value chain. It also analyzes the forces that affect Medtronic using SWOT, PEST, and …

Injectable Glass Polyalkenoate Cements: Evaluation Of Their Rheological And Mechanical Properties With And Without The Incorporation Of Lidocaine Hydrochloride, P. Niranjan, A. Alhalawani, S. Phull, I. Beniluz, B. Krishnan, P. Zalzal, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

Lidocaine hydrochloride is used as an anesthetic in many clinical applications. This short communication investigates the effect of complete substitution of lidocaine hydrochloride for deionized (DI) water on the physico-chemical properties of two novel glass polyalkenoate cements. Substituting DI water with lidocaine hydrochloride resulted in cements with shorter working times but comparable setting times and mechanical properties. Fourier transform infrared spectroscopy confirmed that the setting reaction in cements containing DI water and lidocaine hydrochloride was completed within 24 h, post cement preparation and maturation. Further, it was explained that lidocaine hydrochloride binds to poly(acrylic) acid (PAA) due to electrostatic forces …

The Effect Of Mg²⁺ Incorporation Into The Glass Phase Of Zinc-Based Glass Polyalkenoate Cements, Basel A. Khader, Omar Rodriguez, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

The suitability of glass polyalkenoate cements (GPCs) as injectable adhesives in orthopedics have been compromised by the presence of aluminum (Al), a component in the glass phase of all commercial GPCs. There has been considerable work on the development of Al-free GPCs which can be formulated based on calcium (Ca) zinc (Zn) silicate (Si) glasses. These materials, in terms of biocompatibility and mechanical properties, have potential for orthopedics. However, many of these experimental Al-free GPCs have setting times shorter than 60 s, restricting clinical applications. Here, the authors incorporate Magnesium (Mg) into the glass phase of Al-free GPCs in an …

Virtual Stethoscope/Otoscope Duo, Camila P. Monchini, Paige R. Mazur, Christian Navarro

Biomedical Engineering

The virtual stethoscope/otoscope duo is a medical device intended to allow patients to be seen by their medical provider via internet consultations from the comfort of their own home. This device allows patients to substitute in-person doctor visits by checking a patient’s cardiovascular, respiratory, and auditory health. This document is the statement of work for the virtual stethoscope/otoscope duo and contains information on similar products, patents, and relevant literatures containing virtual technologies that assist in patient diagnosis. Product specifications and other details for the device such as performance evaluation review techniques can also be found within this document outlining the …

Microfluidic Technology And Application In Urinal Analysis, Jiwen Xiang

LSU Doctoral Dissertations

Microfluidic technology offers numerous advantages in minimizing and integrating the traditional assays. However, the lack of efficient control components of the microfluidic systems has been hindering the widely commercialization of the technology. The research work in this dissertation focused on the development of effective control components for microfluidic applications.

A linear peristaltic pump was firstly designed, fabricated, and tested for conventional microfluidics by synchronously compressing the microfluidic channel with a miniature cam-follower system in Chapter 2. The miniature cam-follower system and microfluidic chip was prototyped using three-dimensional (3D) printing technology and soft lithography technology. Results from experimental test showed that …

Raman Spectroscopy Predicts The Link Between Claw Keratin And Bone Collagen Structure In A Rodent Model Of Oestrogen Deficiency, M. Clare Caraher, Antonia Sophocleous, J. Renwick Beattie, Olive O'Driscoll, Niamh M. Cummins, Orlaith Brennan, Fergal J. O'Brien, Stuart H. Ralston, Steven E.J. Bell, Mark R. Towler, Aymen I. Idris

Chemical and Biochemical Engineering Faculty Research & Creative Works

Osteoporosis is a common disease characterized by reduced bone mass and an increased risk of fragility fractures. Low bone mineral density is known to significantly increase the risk of osteoporotic fractures; however, the majority of non-traumatic fractures occur in individuals with a bone mineral density too high to be classified as osteoporotic. Therefore, there is an urgent need to investigate aspects of bone health, other than bone mass, that can predict the risk of fracture. Here, we successfully predicted association between bone collagen and nail keratin in relation to bone loss due to oestrogen deficiency using Raman spectroscopy. Raman signal …

Low Cost Waist Line Circumference Health Management Belt, Raghav Talreja

Research Opportunities for Engineering Undergraduates (ROEU) Program 2017-18

One third of the American population is obese or near obese, and $150 billion is spent in weight management. Current devices to monitor weight are expensive, and niche products are designed for health enthusiasts. This project investigates user needs, development and commercialization steps for a low cost health management belt.

Preparation For The Study Of Gene Expression Aboard The International Space Station, Amber Paturzo

STAR Program Research Presentations

WetLab-2 performs quantitative polymerase chain reaction (qPCR) aboard the micro-gravity environment of the International Space Station in order to research how the stress of micro-gravity affects an organism’s RNA production and gene expression. This on-station qPCR allows researchers to gather information earlier and thereby allow them to modify experiments in a matter of hours rather than wait until the next flight opportunity. After a successful validation flight on SpaceX-8 and follow-up investigation on SpaceX-9, system components must now be adjusted for a new type of biological sample. Specifically, the WetLab-2 facility includes a commercial qPCR instrument (RNA SmartCycler), a sample …

Development Of Low Frequency Electron Paramagnetic Resonance Methods And Instrumentation For Biological Applications, Laura A. Buchanan

Electronic Theses and Dissertations

EPR is a powerful biophysical tool that can be used to measure tumor physiology. With the addition of magnetic field gradients, the spectral properties of paramagnetic species can be mapped. To facilitate EPR imaging, methods and instrumentation at frequencies between 250 MHz and 1 GHz were developed.

At low spin concentrations, the rapid scan background signal is often many times larger than the EPR signal of interest. To help remove the background contribution, a data acquisition procedure that takes advantage of a cross-loop resonator and bipolar power supplies was developed at 250 MHz. In this procedure, two scans are collected. …

The Effect Of Cognitive Limb Embodiment On Vascular Physiological Response, Hala Elsir Mustafa Osman

ETD Archive

The rubber hand illusion (RHI) is a visual-tactile perceptual illusion commonly used to study body ownership. In this paradigm, a rubber hand is positioned in front of a participant, and the person’s real hand is hidden from sight behind a barrier. When the real hand and the rubber hand are stroked synchronously, individuals perceive the rubber hand as if it were their own; it becomes “embodied.” This illusory experience of body ownership is associated with multimodal integration of touch and vision. From these visual-tactile-cognitive mechanisms, we establish that our hands belong to us when what we see matches what we …

Stabilization Of Hypoxia Inducible Factor By Cobalt Chloride Can Alter Renal Transepithelial, Subhra Sankar Nag

ETD Archive

Kidney cyst expansion, stagnant fluid accumulation, and insufficient vascular supply can result in localized chronic ischemia-hypoxia in kidney cysts, as well as in normal renal epithelia adjacent to a cyst. We hypothesize that in normal epithelia near a cyst, the stabilization of Hypoxia Inducible Factor 1a (HIF1a), a major regulator of cellular response to hypoxia, can cause altered paracellular and transcellular transport, transforming a normal absorptive phenotype to a secretory and paracellularly leaky phenotype, leading to cyst expansion. Using 100 µmol/L cobalt chloride (CoCl2), HIF1a was stabilized in cellular nucleus of a mouse cortical collecting duct cell line (mCCD 1296 …

A Machine Learning Approach To Assess The Separation Of Seismocardiographic Signals By Respiration, Brian Solar

Honors Undergraduate Theses

The clinical usage of Seismocardiography (SCG) is increasing as it is being shown to be an effective non-invasive measurement for heart monitoring. SCG measures the vibrational activity at the chest surface and applications include non-invasive assessment of myocardial contractility and systolic time intervals. Respiratory activity can also affect the SCG signal by changing the hemodynamic characteristics of cardiac activity and displacing the position of the heart. Other clinically significant information, such as systolic time intervals, can thus manifest themselves differently in an SCG signal during inspiration and expiration. Grouping SCG signals into their respective respiratory cycle can mitigate this issue. …

A Preliminary Evaluation Of The Ability Of Keratotic Tissue To Act As A Prognostic Indicator Of Hip Fracture Risk, J. Renwick Beattie, Diane Feskanich, M. Clare Caraher, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

Studies have shown that Raman spectroscopic analysis of fingernail clippings can help differentiate between post-menopausal women who have and who have not suffered a fracture. However, all studies to date have been retrospective in nature, comparing the proteins in nails sourced from women, post-fracture. The objective of this study was to investigate the potential of a prospective test for hip fracture based on spectroscopic analysis of nail tissue. Archived toenail samples from post-menopausal women aged 50 to 63 years in the Nurses' Health Study were obtained and analysed by Raman spectroscopy. Nails were matched case-controls sourced from 161 women; 82 …

The Impact Of Gallium Content On Degradation, Bioactivity, And Antibacterial Potency Of Zinc Borate Bioactive Glass, Alireza Rahimnejad Yazdi, Lawrence Torkan, Wendy Stone, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

Zinc borate glasses with increasing gallium content (0, 2.5, 5, 10, and 15 Wt % Ga) were synthesized and their degradation, bioactivity in simulated body fluid (SBF), and antibacterial properties were investigated. ICP measurements showed that increased gallium content in the glass resulted in increased gallium ion release and decreased release of other ions. Degradability declined with the addition of gallium, indicating the formation of more symmetric BO₃ units with three bridging oxygens and asymmetric BO₃ units with two bridging oxygens in the glass network as the gallium content in the series increased. The formation of amorphous Ca-P …

Electrochemical And Spectroscopic Study Of Peptide-Template Melanins, Daniel Courter, Olivia Rossi, Zhen Tian

Honors Theses and Capstones

Melanins are organic polymers made up of 5,6-dihydroxyindole carboxylic acid (DHICA) and 5,6-dihydroxyindole (DHI). Biochemical systems synthesize melanins through a complex reaction pathway. Previous research exhibited that naturally-occurring melanins (NatMel) and their synthetic analogues (SynMel) can potentially serve as electrode materials for aqueous charge storage devices. Small surface area creates technical challenges for these melanins as charge storage materials. This research herein demonstrates that the structure of melanins can affect the charge storage capacities of monovalent Na⁺cations and divalent Mg²⁺ cations. 2-D sheet-like peptide melanins (PepMel) were synthesized into tripeptides consisting of aspartic acid (D), phenylalanine (F), …

Multimodal Noncontact Diffuse Optical Reflectance Imaging Of Blood Flow And Fluorescence Contrasts, Daniel Irwin

Theses and Dissertations--Biomedical Engineering

In this study we design a succession of three increasingly adept diffuse optical devices towards the simultaneous 3D imaging of blood flow and fluorescence contrasts in relatively deep tissues. These metrics together can provide future insights into the relationship between blood flow distributions and fluorescent or fluorescently tagged agents. A noncontact diffuse correlation tomography (ncDCT) device was firstly developed to recover flow by mechanically scanning a lens-based apparatus across the sample. The novel flow reconstruction technique and measuring boundary curvature were advanced in tandem. The establishment of CCD camera detection with a high sampling density and flow recovery by speckle …

Design And Analysis Of A 3d-Printed, Thermoplastic Elastomer (Tpe) Spring Element For Use In Corrective Hand Orthotics, Kevin Thomas Richardson

Theses and Dissertations--Mechanical and Aerospace Engineering

This thesis proposes an algorithm that determine the geometry of 3D-printed, custom-designed spring element bands made of thermoplastic elastomer (TPE) for use in a wearable orthotic device to aid in the physical therapy of a human hand exhibiting spasticity after stroke. Each finger of the hand is modeled as a mechanical system consisting of a triple-rod pendulum with nonlinear stiffness at each joint and forces applied at the attachment point of each flexor muscle. The system is assumed quasi-static, which leads to a torque balance between the flexor tendons in the hand, joint stiffness and the design force applied to …

A Bluetooth Low-Energy Wireless Sensor Platform For Continuous Monitoring Of A Bioreactor Environment During Cell Manufacturing, Brad Nelson

Dissertations, Master's Theses and Master's Reports

A wireless sensor platform based on Bluetooth Low-Energy (BLE) technology was designed and prototyped for continuous monitoring of physical conditions and chemical analytes, which could be applied to bioreactors during the cell manufacturing process. Controlling environmental conditions such as pH, oxygen, glucose, temperature, and pressure is vital to ensure the consistency of the manufactured cells and maintain the potency of the product. Current methods to control bioreactor conditions focus only on monitoring the cell culture environment during cell growth, but there is a lack of direct quantification of cell properties to provide an integrated feedback system that can also maintain …

Wearable Hearing Accessory Technology, Tyler Cindea, Jaime Alcorn, Brooke Draper, Kyle Glascott, Ben Hanna, Robert Thoerner

Williams Honors College, Honors Research Projects

We set out in August 2017 to develop an active noise suppressing device that would be usable both in military and civilian activities. Due to constraints in knowledge and time, we decided our best course of action was to divide the project into two equal projects with the hope to be able to combine them into a single project at the end of the allotted time. This consisted of an active noise suppression device and a passive noise suppression device. The passive device would have no electronic components and the active device would be pure circuitry with no housing. This …

Studying Mass And Mechanical Property Changes During The Degradation Of A Bioadhesive With Mass Tracking, Rheology And Magnetoelastic (Me) Sensors, Zhongtian Zhang

Dissertations, Master's Theses and Master's Reports

In this research, the degradable polymer 4-arm poly (ethylene glycol)-glutaric acid-dopamine (PEG-GA-DM₄) was synthesized. The degradation behavior of crosslinked PEG-GA-DM₄ bioadhesive was studied with mass tracking, oscillatory rheology, and magnetoelastic (ME) sensors. Changes in mechanical properties were correlated with both dry mass and wet mass changes during the degradation. The results indicate that the loss of mechanical property in the bioadhesive can take place without losing the dry mass. The mass loss profile cannot describe the degradation behavior completely. In addition to studying the degradation of PEG-GA-DM₄, this research also confirms the application of ME …