Nanoscience and Nanotechnology Commons^™

Experimental Investigation Of Surface Resistivity Of Yttrium Stabilized Zirconium As A Thin Film, Matthew J. Melfi

Seton Hall University Dissertations and Theses (ETDs)

Solid Oxide Fuel Cells are devices that use electrochemical reactions to convert chemical energy from fuel to electricity. In comparison with coal power plants, a Solid Oxide Fuel Cell, produces a higher electrical conversion efficiency. However, at higher temperatures (1000°C) it creates a lower ionic conductivity, which limit the Solid Oxide Fuel Cells. When lowering the temperature, the ohmic resistance increases. In our research, an Yttrium Stabilized Zirconium layer will be produced from a fine dimple grain structure allowing high flow of oxygen mobility. This mobility increases ionic conductivity and decrease ohmic loss. The goal of our research is first …

On The Comparison Of Flow Physics Between Minimal And Extended Flow Units In Turbulent Channels, Ethan A. Davis, Siamak Mirfendereski, Jae Sung Park

Department of Mechanical and Materials Engineering: Faculty Publications

Direct numerical simulations were performed to study the effects of the domain size of a minimal flow unit (MFU) and its inherent periodic boundary conditions on flow physics of a turbulent channel flow in a range of 200 ≤ Re_τ ≤ 1000. This was accomplished by comparing turbulent statistics with those computed in sub-domains (SD) of extended domain simulations. The dimensions of the MFU and SD were matched, and SD dynamics were set to minimize artificial periodicities. Streamwise and spanwise dimensions of healthy MFUs were found to increase linearly with Reynolds number. It was also found that both MFU …

Impact Of Angiogenic And Osteogenic Factors In The Presence Of Biodegradable Piezoelectric Films, Jayla Millender

Honors Scholar Theses

One of the most common causes of bone graft rejection is lack of a vascular network connecting the graft to the existing native tissue – allowing for nutrient flow. Under current grafting techniques, the existing blood vessel network in the patient slowly invades the implant in order to supply the injured site with its necessary nutrients. The purpose of this research is to determine if a synthetic bone graft with a stable microvascular network can be developed in vitro. I hypothesize that the use of indirect angiogenic factors such as sonic hedgehog homolog and hypoxia-inducible factor-1 in combination with the …

An Investigation Of Testing Parameters On The Frictional Properties Of Patterned Core-Shell Nanostructures, Colin Phelan

Graduate Theses and Dissertations

Friction tests are a beneficial means to analyze the tribological characteristics and advantages of materials and textured surfaces. However, the selected test parameters can significantly influence the results. This work explores the significance of the friction testing parameters on the frictional performances of core-shell nanostructure-textured surfaces (CSNTSs). Several applied normal loads (10 μN, 100 μN, and 500 μN) and diamond counterface indenter tip radii (1 μm, 5 μm, and 20 μm) were selected for the testing of Al/diamond-like-carbon (DLC) and Al/amorphous silicon (a-Si) CSNTSs. The measured friction values of the CSNTSs were then compared to a matching Al/DLC film and …

Designing Cryogenic Strain Device For 2d Materials, Jake Carter

Mechanical Engineering Undergraduate Honors Theses

The Churchill lab working within the Physics Department at the University of Arkansas is working to create important quantum states including weak topological insulators (TIs) through the use of symmetry engineering and topological electronic states in two-dimensional (2D) crystals of WHM materials. Experimental results of these topological states have been obstructed due to the difficulty to perform controlled in situ strain. This project strives to create a mount to utilize a piezoelectric nanopositioner within cryostats achieving an in situ strain that creates the quantum states the lab is looking to observe. This report also examines the necessary equations to determine …

Mechanical Analysis Of A Heterogeneously Integrated Silicon Photonic Interposer, Erica Charlene Graham

Legacy Theses & Dissertations (2009 - 2024)

Overcoming the bandwidth bottleneck in conventional interconnects necessitates transitioning to alternative scaling paradigms. Silicon (Si) photonics is considered a disruptive technology, capable of meeting the growing demands for higher bandwidth, low latency, and power efficiency. By leveraging the intrinsic properties of optical signals and manufacturing compatibility of Si, the co-integration of Si photonics and complementary-metal-oxide-semiconductor (CMOS) circuitry leading to terabit data speeds for next generation data communication can be realized. Heterogeneously integrating Si photonic functionality with well-established CMOS technology in an Si photonic interposer architecture simultaneously provides independent optimization as well as close integration of both technologies in one platform. …

Statistical And Variational Modeling And Analysis Of Passive Integrated Photonic Devices, Norbert Dinyi Agbodo

Legacy Theses & Dissertations (2009 - 2024)

The success of Si as a platform for photonic devices and the associated availabilityof wafer-scale, ultra-high resolution lithography for Si CMOS has helped lead to the rapid advance of Si-based integrated photonics manufacturing over the past decade. This evolution is nearing the point of integration of Si-based photonics together with Si-CMOS for compact, high speed, high bandwidth, and cost-effective devices. However, due to the sensitive nature of passive and active photonic devices, variations inherent in wafer-based fabrication processes can lead to unacceptable levels of performance variation both within a give die and across a given wafer. Fully understanding the role …

Development Of A Laser-Assisted Chemical Vapor Deposition (Cvd) Technique To Grow Carbon-Based Materials, Abiodun Ademola Odusanya

Graduate Theses/Dissertations

Carbon-based materials (CBMs) including graphene, carbon nanotubes (CNT), highly ordered pyrolytic graphite (HOPG), and pyrolytic carbon (PyC) have gained so much attention in research in recent years because of their unique electronic, optical, thermal, and mechanical properties. CBMs are relatively very stable and have minimal environmental footprint. Various techniques such as mechanical exfoliation, pulsed laser deposition, and chemical vapor deposition (CVD) have been used to grow CBMs and among them thermal CVD is the most common. This study aims to explore ways of reducing the energy requirement to produce CBMs, and for that, a novel pulsed laser-assisted CVD technique had …

Nanoscratch Study Of Diamond-Like Carbon Coatings With A Polydopamine + Sio2 Adhesive Underlayer, Anna Fisher

Mechanical Engineering Undergraduate Honors Theses

Diamond-like carbon (DLC) coatings have a wide array of desirable characteristics such as low friction, high hardness, and scratch resistance. Due to high residual stress and thermal mismatch, DLC films experience adhesion difficulties when bonded with metallic substrates, leading to cracking and delamination. In this study, the properties of a new coating with a polydopamine underlayer and silica nanoparticles bonded to a stainless-steel substrate (PDA+SiO2/DLC) were studied alongside three other samples, one with a polydopamine underlayer (PDA/DLC), one with a trimethylsilane (TMS) underlayer (TMS/DLC), and one with no underlayer (DLC only). Nanoscratch tests were performed with a 1 μm spheroconical …

Tensile-Strained Germanium Quantum Dots Grown On Indium Aluminum Arsenide (111)A And (110) By Molecular Beam Epitaxy, Kathryn Eva Sautter

Boise State University Theses and Dissertations

Molecular beam epitaxy (MBE) enables the growth of semiconductor nanostructures known as tensile-strained quantum dots (TSQDs). The highly tunable nature of TSQD properties means that they are of interest for a wide variety of applications including for infrared (IR) lasers and light-emitting diodes (LEDs), improved tunnel junction efficiency in multijunction solar cell technology, quantum key encryption, and entangled photon emission. In this project, I focus on one of the most technologically important materials, germanium (Ge). Ge has a high gain coefficient, high electron mobility, and low band gap: all excellent properties for optoelectronic applications. Until recently, these technological advantages were …

Photothermal Response Induced By Nanocage-Coated Artificial Extracellular Matrix Promotes Neural Stem Cell Differentiation, Seunghyun Jung, Nathaniel Harris, Isabelle I. Niyonshuti, Samir V. Jenkins, Abdallah M. Hayar, Fumiya Watanabe, Azemat Jamshidi-Parsian, Jingyi Chen, Michael J. Borrelli, Robert J. Griffin

Mechanical Engineering Faculty Publications and Presentations

Strategies to increase the proportion of neural stem cells that differentiate into neurons are vital for therapy of neurodegenerative disorders. In vitro, the extracellular matrix composition and topography have been found to be important factors in stem cell differentiation. We have developed a novel artificial extracellular matrix (aECM) formed by attaching gold nanocages (AuNCs) to glass coverslips. After culturing rat neural stem cells (rNSCs) on these gold nanocage-coated surfaces (AuNC-aECMs), we observed that 44.6% of rNSCs differentiated into neurons compared to only 27.9% for cells grown on laminin-coated glass coverslips. We applied laser irradiation to the AuNC-aECMs to introduce precise …

Exploration Of Antimicrobial And Cell Proliferation Properties Of Nanofibers Incorporating Nopal (O. Cochenillifera) Extract, Cristobal Rodriguez

Theses and Dissertations

This study focused on the fabrication of Forcespinning® nanofibers composed of Opuntia cochenillifera, ‘nopal’, mucilage (N) extract, chitosan (CH), and pullulan (PL) (N/CH/PL) were developed with an optimum fiber average diameter of 406±127 nm, and studied for their ability to sustain adhesion and proliferation of mouse embryonic fibroblast (NIH 3T3) cells. After a 6-day incubation period, N/CH/PL nanofibers displayed robust cell proliferation, while also exhibiting inhibitory properties through an N extract dip-coating process against gram-negative bacteria Escherichia coli in a 24 h bacterial growth study. A demonstration of integrated natural bioactive compounds with combined biodegradable polymers, provide an enhanced …

Peptoid-Functionalized Gold Nanoparticles For Zika Virus Envelope Protein Detection, Meagan Olsen

Chemical Engineering Undergraduate Honors Theses

Detection and identification of viral pathogens is essential in providing effective and rapid medical treatment. Well-established detection methods can be expensive, slow, and sometimes unable to provide the needed sensitivity and specificity. The Zika virus is one clinically relevant pathogen that cannot be easily identified due to cross-reactivity with other viruses from the same family. Electrochemical sensors enhanced with peptoid-functionalized gold nanoparticles (AuNPs) are an alternative to traditional techniques that offers rapid, accurate, label-free pathogen detection for point-of-care diagnostics. To this end, a peptoid capable of binding to the Zika virus envelope protein was developed and its binding affinity for …

Degradation Of Antibiotics In Aqueous Phase Using Pms Catalytic Decomposition With Zero-Valent Iron Nanoparticles Immobilized In Sba-15, Ahdee Bluma Zeidman

UNLV Theses, Dissertations, Professional Papers, and Capstones

Zero-valent iron nanoparticles (nZVI) have been studied as an option for soil remediation and water treatment for many years. The capability of nZVI to produce oxidation/reduction processes, depending on the reaction conditions, has attracted great interest with their major drawback being reactivity loss through agglomeration. The loss in nZVI surface area has been reported to be prevented through immobilization onto a porous media (e.g., SBA-15, MCM-41, or zeolites). In this work, a mesoporous silica structure (SBA-15) is used as an nZVI supporting material to enhance its reactivity and promote peroxymonosulfate (PMS) catalytic decomposition for the degradation of antibiotics in aqueous …

Fabrication Of Forcespinning® Nanofibers Incorporating Nopal Extract, Cristobal Rodriguez, Victoria Padilla, Karen Lozano, J. Andrew Mcdonald, Luis Materon, Alejandra Chapa, Fariha Ahmad, Carlos Trevino De Leon, Robert Gilkerson

School of Integrative Biological & Chemical Sciences (Formerly Dept. of Biology)

In this study, nanofibers composed of Opuntia cochenillifera nopal mucilage (N) extract combined with chitosan (CH) and pullulan (PL) (N/CH/PL) were produced via Forcespinning®. The developed nonwoven composite membranes are comprised of long, continuous, and homogenous fibers with fiber average diameter varying between 251±77 nm and 406±127 nm depending on the concentration of N. After crosslinking, the developed membranes were highly stable in water. The water absorption capacity of the N/CH/PL composite nanofiber membranes was shown to be 65% higher when compared to the CH/PL nanofiber membranes. Nopal dipcoated membranes show inhibition of gram-negative Escherichia coli, indicating antibacterial properties. These …

Characterization Of Protein Aggregation Using A Solid-State Nanopore Device, Mitu Chandra Acharjee

Graduate Theses and Dissertations

Protein aggregation has been linked to many chronic and devastating neurodegenerative human diseases and is also strongly associated with aging. In the case of neurodegenerative diseases, α, β tubulins and tau proteins dissociate in a neuron cell and aggregate both intra and extra-cellularly. Tau and tubulin aggregations were found as one of the major causes of many neurodegenerative diseases, such as Parkinson’s, Picks, Alzheimer’s, Huntington, and Prion. Finding the state and mechanism of protein aggregation is significant. In this work, tau and tubulin aggregations were detected in ionic solutions using the solid-state nanopore technique. Besides tau and tubulin, aggregations of …

Oxone® Mediated Tempo-Oxidized Cellulose Nanomaterials: Material Characterization, Ultrafiltration Membrane Separations, And Thin Film Composite Gas Transport Analysis, John Phillips Moore

Graduate Theses and Dissertations

Cellulose nanomaterials (CNMs) are derived from plant matter and are comprised of nanoscopic cellulose crystals and fibers. They have a diverse set of applications, from cosmetics to oil recovery. This study focuses on the properties of Oxone® mediated TEMPO-oxidized cellulose nanomaterials (OTO-CNMs) and their use in controlling the transport properties of polymeric substrates. Synthesis and characterization of cellulosic nanoparticles have resulted in the creation of OTO-CNMs with properties that increase hydrophilicity. With added hydrophilicity, OTO-CNMs possess lower fouling propensity, making them ideal membrane additive for transport limited separations such as hemodialysis.

To utilize the material and unique properties thereof, this …

Mixed Mode Crack Propagation In Iliac Bone, E. Baesu, Dm. Iliescu, Bv. Radoiu, S. Halichidis

Department of Mechanical and Materials Engineering: Faculty Publications

Bone is a complex material that can be regarded as an anisotropic elastic composite material. The problem of crack propagation in hu- man bone is analyzed by using a generalization of the maximum tensile stress criterion (MTS). The results concern the critical stress for crack propagation and the direction of the crack path in Iliac bone.

Special Issue “Cfd Modeling Of Complex Chemical Processes: Multiscale And Multiphysics Challenges”, Li Xi, De-Wei Yin, Jae Sung Park

Department of Mechanical and Materials Engineering: Faculty Publications

No abstract provided.

Electrochemical Surface-Enhanced Raman Spectroscopic Studies On Nickel Ultramicroelectrode, Li-Wen Wu, Wei Wang, Yi-Fan Huang

Journal of Electrochemistry

Nickel (Ni) electrodes are widely used in electrochemical researches. Understanding electrochemical processes on Ni electrodes through in-situ characterization of adsorbed species on their surfaces is helpful for rational optimization and application of Ni electrochemistry. Microelectrochemical surface-enhanced Raman spectroscopy (μEC-SERS) combines the mass transfer feature of ultramicroelectrode with high-sensitivity characterizations of molecular structures, which is a powerful method for studying Ni electrochemistry on polarization and non-equilibrium conditions. The key point of performing μEC-SERS is to make a SERS-active Ni ultramicroelectrode.
Here, we demonstrate a method of preparing a SERS-active Ni ultramicroelectrode through electrochemical deposition of several atomic layers of …