Electrical and Electronics Commons^™

Autonomous Recovery Of Reconfigurable Logic Devices Using Priority Escalation Of Slack, Naveed Imran

Electronic Theses and Dissertations

Field Programmable Gate Array (FPGA) devices offer a suitable platform for survivable hardware architectures in mission-critical systems. In this dissertation, active dynamic redundancy-based fault-handling techniques are proposed which exploit the dynamic partial reconfiguration capability of SRAM-based FPGAs. Self-adaptation is realized by employing reconfiguration in detection, diagnosis, and recovery phases. To extend these concepts to semiconductor aging and process variation in the deep submicron era, resilient adaptable processing systems are sought to maintain quality and throughput requirements despite the vulnerabilities of the underlying computational devices. A new approach to autonomous fault-handling which addresses these goals is developed using only a uniplex …

Differential Games For Multi-Agent Systems Under Distributed Information, Wei Lin

Electronic Theses and Dissertations

In this dissertation, we consider differential games for multi-agent systems under distributed information where every agent is only able to acquire information about the others according to a directed information graph of local communication/sensor networks. Such games arise naturally from many applications including mobile robot coordination, power system optimization, multiplayer pursuit-evasion games, etc. Since the admissible strategy of each agent has to conform to the information graph constraint, the conventional game strategy design approaches based upon Riccati equation(s) are not applicable because all the agents are required to have the information of the entire system. Accordingly, the game strategy design …

Modeling And Simulation Of All-Electric Aircraft Power Generation And Actuation, David Woodburn

Electronic Theses and Dissertations

Modern aircraft, military and commercial, rely extensively on hydraulic systems. However, there is great interest in the avionics community to replace hydraulic systems with electric systems. There are physical challenges to replacing hydraulic actuators with electromechanical actuators (EMAs), especially for flight control surface actuation. These include dynamic heat generation and power management. Simulation is seen as a powerful tool in making the transition to all-electric aircraft by predicting the dynamic heat generated and the power flow in the EMA. Chapter 2 of this dissertation describes the nonlinear, lumped-element, integrated modeling of a permanent magnet (PM) motor used in an EMA. …

Analysis And Design Optimization Of Multiphase Converter, Kejiu Zhang

Electronic Theses and Dissertations

Future microprocessors pose many challenges to the power conversion techniques. Multiphase synchronous buck converters have been widely used in high current low voltage microprocessor application. Design optimization needs to be carefully carried out with pushing the envelope specification and ever increasing concentration towards power saving features. In this work, attention has been focused on dynamic aspects of multiphase synchronous buck design. The power related issues and optimizations have been comprehensively investigated in this paper. In the first chapter, multiphase DC-DC conversion is presented with background application. Adaptive voltage positioning and various nonlinear control schemes are evaluated. Design optimization are presented …

Rf Power Amplifier And Oscillator Design For Reliability And Variability, Shuyu Chen

Electronic Theses and Dissertations

CMOS RF circuit design has been an ever-lasting research field. It gained so much attention since RF circuits have high mobility and wide band efficiency, while CMOS technology has the advantage of low cost and better capability of integration. At the same time, IC circuits never stopped scaling down for the recent many decades. Reliability issues with RF circuits have become more and more severe with device scaling down: reliability effects such as gate oxide break down, hot carrier injection, negative bias temperature instability, have been amplified as the device size shrinks. Process variability issues also become more predominant as …

Investigation On Electrical Properties Of Rf Sputtered Deposited Bcn Thin Films, Adithya Prakash

Electronic Theses and Dissertations

The ever increasing advancements in semiconductor technology and continuous scaling of CMOS devices mandate the need for new dielectric materials with low-k values. The interconnect delay can be reduced not only by the resistance of the conductor but also by decreasing the capacitance of dielectric layer. Also cross-talk is a major issue faced by semiconductor industry due to high value of k of the inter-dielectric layer (IDL) in a multilevel wiring scheme in Si ultra large scale integrated circuit (ULSI) devices. In order to reduce the time delay, it is necessary to introduce a wiring metal with low resistivity and …

A Novel Nonlinear Mason Model And Nonlinear Distortion Characterization For Surface Acoustic Wave Duplexers, Li Chen

Electronic Theses and Dissertations

Surface acoustic wave (SAW) technology has been in use for well over one century. In the last few decades, due to its low cost and high performance, this technology has been widely adopted in modern wireless communication systems, to build filtering devices at radio frequency (RF). SAW filters and duplexers can be virtually found inside every mobile handset. SAW devices are traditionally recognized as passive devices with high linear signal processing behavior. However, recent deployments of third generation (3G) and fourth generation (4G) mobile networks require the handsets to handle an increasing number of frequency bands with more complex modulation …

Polymer Optical Fibers For Luminescent Solar Concentration, Esmaeil Banaei

Electronic Theses and Dissertations

Luminescent solar concentrators (LSC’s) are promising candidates for reducing the cost of solar power generation. Conventional LSC’s are slab waveguides coated or doped with luminescence materials for absorption and guiding of light to the slab edges in order to convert optical energy into electricity via attached photovoltaic (PV) cells. Exploiting the advantages of optical fiber production, a fiber LSC (FLSC) is presented in this thesis, in which the waveguide is a polymeric optical fiber. A hybrid fiber structure is proposed for an efficient two-stage concentration of incident light, first into a small doped core using a cylindrical micro-lens that extends …

Transient And Distributed Algorithms To Improve Islanding Detection Capability Of Inverter Based Distributed Generation, Mohamed Al Hosani

Electronic Theses and Dissertations

Recently, a lot of research work has been dedicated toward enhancing performance, reliability and integrity of distributed energy resources that are integrated into distribution networks. The problem of islanding detection and islanding prevention (i.e. anti-islanding) has stimulated a lot of research due to its role in severely compromising the safety of working personnel and resulting in equipment damages. Various Islanding Detection Methods (IDMs) have been developed within the last ten years in anticipation of the tremendous increase in the penetration of Distributed Generation (DG) in distribution system. This work proposes new IDMs that rely on transient and distributed behaviors to …

Distributed Extremum Seeking And Cooperative Control For Mobile Cooperative Communication Systems, Said Alabri

Electronic Theses and Dissertations

In this thesis, a distributed extremum seeking and cooperative control algorithm is designed for mobile agents to disperse themselves optimally in maintaining communication quality and maximizing their coverage. The networked mobile agents locally form a virtual multiple-input multipleoutput (MIMO) communication system, and they cooperatively communicate among them by using the decode and forward cooperative communication technique. The outage probability is used as the measure of communication quality, and it can be estimated real-time. A general performance index balancing outage probability and spatial dispersion is chosen for the overall system. The extremum seeking control approach is used to estimate and optimize …

Holistic Representations For Activities And Crowd Behaviors, Berkan Solmaz

Electronic Theses and Dissertations

In this dissertation, we address the problem of analyzing the activities of people in a variety of scenarios, this is commonly encountered in vision applications. The overarching goal is to devise new representations for the activities, in settings where individuals or a number of people may take a part in specific activities. Different types of activities can be performed by either an individual at the fine level or by several people constituting a crowd at the coarse level. We take into account the domain specific information for modeling these activities. The summary of the proposed solutions is presented in the …

Multi-Physics Model Of Key Components In High Efficiency Vehicle Drive, Shao Hua Lin

Electronic Theses and Dissertations

Hybrid Electric Vehicles (HEVs) and Electric Vehicles (EVs) are crucial technologies for the automotive industry to meet society’s demands for cleaner, more energy efficient transportation. Meeting the need to provide power which sustains HEVs and EVs is an immediate area of concern that research and development within the automotive community must address. Electric batteries and electrical motors are the key components in HEV and EV power generation and transmission, and their performance plays very important role in the overall performance of the modern high efficiency vehicles. Therefore, in this dissertation, we are motivated to study the electric batteries, interior permanent …

Monolithically Integrated Broadly Tunable Light Emitters Based On Selectively Intermixed Quantum Wells, Abdullah Zakariya

Electronic Theses and Dissertations

A monolithically integrated broadly tunable MQW laser that utilizes a combined impurity-free vacancy disordering (IFVD) of quantum wells and optical beam steering techniques is proposed and investigated experimentally. The device consists of a beam-steering section and an optical amplifier section fabricated on a GaAs/AlGaAs quantum well (QW) p-i-n heterostructure. The beam steering section forms a reconfigurable optical waveguide that can be moved laterally by applying separately controlled electrical currents to two parallel contact stripes. The active core of the gain section is divided in into selectively intermixed regions. The selective intermixing of the QW in the gain section results in …

Microstrip Patch Electrically Steerable Parasitic Array Radiators, Justin Luther

Electronic Theses and Dissertations

This dissertation explores the expansion of the Electrically Steerable Parasitic Array Radiator (ESPAR) technology to arrays using microstrip patch elements. Scanning arrays of two and three closely-coupled rectangular patch elements are presented, which incorporate no phase shifters. These arrays achieve directive radiation patterns and scanning of up to 26° with maintained impedance match. The scanning is effected by tunable reactive loads which are used to control the mutual coupling between the elements, as well as additional loads which compensate to maintain the appropriate resonant frequency. The design incorporates theoretical analysis of the system of coupled antennas with full-wave simulation. A …

Optimization And Design Of Photovoltaic Micro-Inverter, Qian Zhang

Electronic Theses and Dissertations

To relieve energy shortage and environmental pollution issues, renewable energy, especially PV energy has developed rapidly in the last decade. The micro-inverter systems, with advantages in dedicated PV power harvest, flexible system size, simple installation, and enhanced safety characteristics are the future development trend of the PV power generation systems. The double-stage structure which can realize high efficiency with nice regulated sinusoidal waveforms is the mainstream for the micro-inverter. This thesis studied a double stage micro-inverter system. Considering the intermittent nature of PV power, a PFC was analyzed to provide additional electrical power to the system. When the solar power …

Ultrafast Laser Material Processing For Photonic Applications, Mark Ramme

Electronic Theses and Dissertations

Femtosecond Laser Direct Writing (FLDW) is a viable technique for producing photonic devices in bulk materials. This novel manufacturing technique is versatile due to its full 3D fabrication capability. Typically, the only requirement for this process is that the base material must be transparent to the laser wavelength. The modification process itself is based on non-linear energy absorption of laser light within the focal volume of the incident beam. This thesis addresses the feasibility of this technique for introducing photonic structures into novel dielectric materials. Additionally, this work provides a deeper understanding of the lightmatter interaction mechanism occurring at high …

Power Quality Improvement Of Distributed Generation Integrated Network With Unified Power Quality Conditioner., Shafiuzzaman Khan Khadem

Doctoral

With the increased penetration of small scale renewable energy sources in the electrical distribution network, maintenance or improvement of power quality has become more critical than ever where the level of voltage and current harmonics or disturbances can vary widely. For this reason, Custom Power Devices (CPDs) such as the Unified Power Quality Conditioner (UPQC) can be the most appropriate solution for enhancing the dynamic performance of the distribution network, where accurate prior knowledge may not be available. Therefore, the main objective of the present research is to investigate the (i) placement (ii) integration (iii) capacity enhancement and (iv) real …

Emulation Of An Aeroderivative Twin-Shaft Gas Turbine Engine Using An Ac Electric Motor Drive, Blanca A. Correa

Theses and Dissertations

This dissertation presents a method to use an electric motor to emulate the steady-state and transient shaft power characteristics of an aeroderivative twin-shaft turbine engine. Model-based control provides the framework for developing an aeroderivative twin-shaft engine emulation system. Criteria are developed to appropriately specify the motor and variable-speed drive, based on torque, power, and inertia. This method accounts for the difference in inertia between the engine and the emulating motor; it establishes for the first time the nominal and peak torque requirements of the machine and the peak power and current requirements of the electronic motor drive (inverter).

Our results …

Coordinated Control Of Power Electronic Converters In An Autonomous Microgrid, Gholamreza Dehnavi

Theses and Dissertations

Advances in power electronics and generation technologies have increased the viability of distributed generation systems. A microgrid is a special category of distributed generation systems that is distinguished by its size and the ability to operate independently as an islanded system. As long as a microgrid is connected to a large grid, quality of the voltage is supported by the main grid and each power source connected to the microgrid generates independently. In contrast, in the islanded operation of microgrids and in electrical islands such as shipboard distribution systems, dynamics are strongly dependent on the connected sources and on the …

Passive Equalizer Topology Analysis For Signal Integrity Applications, Kuo-Lun Yen

Theses and Dissertations

In high-speed, high density PCB bus systems, high frequency signal losses and crosstalk can have great impacts on signal integrity and digital timing, which can distort transmitted signals, worsen eye diagrams, and attenuate signal amplitudes. Also, these impacts make digital signals and their energy smearing over multiple bit positions as known as jitters, and cause the phenomenon of inter-symbol interference (ISI) in digital signal transmissions.

The main objective of this thesis is to analyze and develop efficient topology circuits for compensating bus system high frequency losses by using equalization techniques. The thesis has focused on study of various practical and …

Fault Aware Soft Restart Of An Islanded Microgrid Using An Inverter Coupled Energy Storage System, Asif Anwar

Theses and Dissertations

This research developed a method for autonomous operation of an inverter-coupled energy storage system for safe islanding- re-energization - and reconnection of the facility-island or microgrid to the utility / distribution circuit in a seamless manner in the event of a fault. This enables the energy storage system to function as an autonomous source within the utility power distribution system without the need to re-engineer the existing protection coordination in the distribution system. Fault detection based on voltage measurements from the inverter terminals are used to detect a fault and isolate the energy storage-powered facility with negligible power feed into …

Ultrawideband (Uwb) And Reconfigurable Antennas - New Concepts For Conformal Load Bearing Antenna Structures (Clas), Nicholas Bishop

Theses and Dissertations

Conformal antennas have been increasingly playing an important role in a vast number wireless of communication applications. More specifically, Conformal Load Bearing Antenna Structures (CLAS) have drawn a great deal of interest among researchers and engineers because of their advantages of multiple functionality, e.g. antenna and structure both. The objectives of this thesis are to investigate and design innovative conformal Ultrawideband (UWB) endfire antenna arrays and reconfigurable aperture coupled pixel patch antennas both of which are good candidates for CLAS. First, a broadband VHF-UHF end-fire Yagi-Uda array is proposed for possible air vehicle integration and operation within the 240-465 MHz …

Analysis Of Modulation And Voltage Balancing Strategies For Modular Multilevel Converters, Ryan Blackmon

Theses and Dissertations

Modular multilevel converters are an emerging voltage source converter topology suitable for many applications. The increased utilization of HVDC power transmission solutions has resulted in modular multilevel converters becoming a more common converter type. Other applications include interfacing renewable energy power sources to the grid and motor drives. Modular multilevel converters are beneficial for medium voltage motor drives because the properties of this converter topology, such as low distortion, allow for an efficient motor drive design.

Modular multilevel converters are designed where instead of using 6 IGBTs as in a conventional voltage source converter, numerous low-rated IGBTs are used to …

Effects Of N-Type Doping On Algan Material Quality, Devendra Diwan

Theses and Dissertations

The field of group III-nitride semiconductors has seen incredible developments during last couple of decades. They are recognized as the most promising materials for a wide field of optoelectronics and electronic devices. Their bandgap ranges from 6.2 eV for AlN to 0.7 eV for InN, covering a wide spectral range from infrared (1.77 mm) to deep ultraviolet (200 nm). Their direct bandgap makes them useful for fabricating optoelectronic devices such as light emitting diodes (LEDs), laser diodes (LDs), and photodetectors. III-nitride semiconductor materials also possess strong bond strengths and exhibit good structural, chemical and thermal stability. These properties make it …

Fault Protection In Dc Distribution Systems Via Coordinated Control Of Power Supply Converters And Bus Tie Switches, Pietro Cairoli

Theses and Dissertations

A new fault protection method responds to the current needs of emerging dc power distribution systems by coordinating electronic power converters and mechanical contactors to rapidly isolate short circuit faults while maintaining continuity of power to loads. This work is important because the increasing performance, higher efficiency, and decreasing cost of electronic power converters have spurred a rediscovery and proliferation of dc power distribution systems. Although dc distribution offers advantages such as higher transmission efficiency, higher power density, higher reliability, and ease of interfacing asynchronous sources, enthusiasm for adopting dc technologies suffers from widespread concern over the means to protect …

High Performance Rf Control Devices Using Capacitively Coupled Contacts (C3) Over Iii-N Heterostructures, Faisal Jahan

Theses and Dissertations

RF switches, power limiters and other control devices are essential components of modern RF systems. RF switches are important parts of wireless modules of various devices such as laptops, tablets, cell phones etc. and key components of satellites communication systems, radars, multi-band wireless and aerospace communications, phased array antennas. RF Power limiters (PL) are also important components of RF systems protecting linear amplifiers, detectors etc. from high-power stress. Traditionally, RF switches are fabricated using pin diodes or MEMS, Si MOSFETs or GaAs HEMTs. RF PLs are typically implemented using Schottky or pin-diodes. Traditional devices used in RF switch and PLs …

Impedance Estimation Using Randomized Pulse Width Modulation And Power Converters, William M. Mccoy

Theses and Dissertations

With the adoption of technologies such as alternative energy production, DC power grids, and electric vehicles, the use of high power switching converters has seen a dramatic increase. These power converters serve many rolls such as grid-tied inverters in solar farms, high power charging for electric vehicles, motor drives for industrial applications, and DC links in transmission systems. With the increased prevalence of such devices, it is only natural to attempt to optimize their operation. As with any level of converter, it is desirable to have accurate control over the generated voltages and currents. Often, these controllers implement some form …

Iii-V Nitride Micro- And Nano-Scale Cantilevers For Multimodal Sensing Applications, Ehtesham Bin Quddus

Theses and Dissertations

Recent research trends in chemical and biological sensing have been geared toward developing molecular sensor devices that are fast, label free, miniaturized and portable. The performance of these devices can be dramatically improved by utilizing multimodal detection techniques, new materials and micro-/nanofabrication technologies. This is especially true for micro-/nanoscale cantilever sensors, which undergo changes in mechanical or electrical properties upon the specific binding of molecules. To develop the sensor devices with the above attributes, we utilized III-V nitride materials: InN nanowires for realizing nanoscale cantilevers and AlGaN/GaN heterostuctures with or without embedded HFETs, for developing microcantilevers. There are mainly two …

Electromagnetic Modeling Of Gan Varactor Microwave Switches, Yi-Hsuan Yang

Theses and Dissertations

Microwave switches are important components which have been widely used in many microwave systems, such as electronic products, satellites communications, antennas, and radars etc. Traditionally, microwave switches are fabricated using pin diodes or MEMS, Si MOSFETs or GaAs HEMTs. These devices, due to the material limitations are suffering from a low breakdown voltage and are unable to handle high power. III-Nitride based varactor microwave switches provide opportunities for high power microwave devices, due to highly conducting 2D electron gas in the channel and high breakdown electric field.

Designing microwave switches typically involves modeling and simulation using tools such as MATLAB, …

Stabilizing Controller Design For A Dc Power Distribution System Using A Passivity-Based Stability Criterion, Antonino Riccobono

Theses and Dissertations

In modern times there has been an increased penetration of power electronic converters into Power Distribution Systems. In particular, there has been a strong interest in DC Power Distribution Systems as opposed to conventional AC Power distribution systems. These DC Power Distribution Systems are enabled by power electronics converters. The strong interest is motivated by improvements in power electronic converter technology, like advances in power semiconductor devices, magnetics, control, and converter topologies which have made possible to build high-performance converters at low cost. In many systems, such as cars, ships and airplanes, there has also been a trend towards the …