Electrical and Electronics Commons^™

Measurement Of Moisture Levels In Oils And Lubricants Using A Novel Moisture Sensor, Aaron Swartz, Ronak Ali

Electrical and Computer Engineering Graduate Research

It is very challenging to measure moisture levels in oils. There is not a good method to measure it. Using the novel moisture sensor invented by Dr. Zhi David Chen, we tried various methods to measure the moisture levels in oils. The initial trials are to immerse the sensor chip into the oils to see any sensor reading changes with the change of moisture levels in oils. It was observed that the sensor reading was unstable even after immersion into the oil for two weeks. The idea for immersion of the sensor chip into the oils failed due to the …

Safety Monitoring & Intelligent Power Distribution Systems For Compact Agricultural Equipment, Mason O. Bradley

Theses and Dissertations--Biosystems and Agricultural Engineering

The agricultural industry continues to be one of the most dangerous career fields in the United States of America with compact agricultural equipment being a common source for casualties in the industry. The primary focus of this work is to develop new technology that improves operational safety of compact agricultural equipment through the use of low-cost embedded electronics. This work presents the design of three systems in alignment with this goal.

The first system aims to integrate electrical intelligence and passive safety monitoring into the power distribution system of a small piece of agricultural equipment. The system known as the …

Modeling And Analysis Of Amorphous Steel Transformer For Potential Loss Reduction In Power Systems., Daniel A. Muchow

Theses and Dissertations--Electrical and Computer Engineering

The energy consumed in power systems can be reduced directly by implementing new technologies and materials. The effort to reduce the carbon emissions expelled from the production of electrical energy has become a major focus. According to the U.S. energy Information Administration approximately 5% of all the electric generated and transmitted in the U.S. electrical grid is lost. The energy profile calculated from the usage of electrical power from all 50 states in 2021 is estimated to be 3.8 billion megawatts per hour, with a state average of just over 11 cents per MWh, producing just over 41.8 billion in …

Surface Morphology And Moisture Adsorption/Desorption Characteristics Of Hybrid-Dielectric Moisture Sensors, Ronak Ali

Theses and Dissertations--Electrical and Computer Engineering

Relative humidity sensors are used for high-humidity measurement. Moisture sensors, or dew point sensors are used for low-humidity measurement (< 1 ppm_v). The dissertation contains two parts of studies. In the first part, the effect of surface morphology on the response speed of moisture sensors is studied. Moisture sensors using α-Al₂O₃ films as porous dielectric materials deposited by anodic spark deposition are studied. In this part of the study, a variety of small pores have been studied to investigate the response speed of moisture sensors. Three different surface morphologies have been studied using scanning electron microscopy. One …

Measurement Of Moisture Levels In Oils And Lubricants Using A Novel Moisture Sensor, Aaron Swartz

Theses and Dissertations--Electrical and Computer Engineering

It is very challenging to measure moisture levels in oils. There is not a good method to measure it. Using the novel moisture sensor, we tried various methods to measure the moisture levels in oils. The initial trials are to immerse the sensor chip into the oils to see any sensor reading changes with the change of moisture levels in oils. It was observed that the sensor reading was unstable. The idea for immersion of the sensor chip into the oils failed. The last idea is to heat the oil to let all moisture evaporate fully. Before heating, the dew …

Lifecycle Carbon Footprint And Sustainability Evaluation Of Dram-Based Processing In Memory Computing Architectures, Samrat Pravin Patel

Theses and Dissertations--Electrical and Computer Engineering

The use of computing technologies has significantly enhanced several aspects of our day-to-day lives. But it has still revealed significant environmental concerns, primarily related to greenhouse gas emissions and energy consumption. Initially, the primary environmental problems associated with computing were energy consumption during device operation. However, with the rapid advancement of technology and increasing computational demands, attention has shifted towards the embodied carbon footprint. This term refers to the total greenhouse gas emissions throughout a product’s lifecycle from the extraction of raw materials to end-of-life processing. It has become increasingly significant in the context of manufacturing integrated circuits (ICs), such …

Reinventing Integrated Photonic Devices And Circuits For High Performance Communication And Computing Applications, Venkata Sai Praneeth Karempudi

Theses and Dissertations--Electrical and Computer Engineering

The long-standing technological pillars for computing systems evolution, namely Moore's law and Von Neumann architecture, are breaking down under the pressure of meeting the capacity and energy efficiency demands of computing and communication architectures that are designed to process modern data-centric applications related to Artificial Intelligence (AI), Big Data, and Internet-of-Things (IoT). In response, both industry and academia have turned to 'more-than-Moore' technologies for realizing hardware architectures for communication and computing. Fortunately, Silicon Photonics (SiPh) has emerged as one highly promising ‘more-than-Moore’ technology. Recent progress has enabled SiPh-based interconnects to outperform traditional electrical interconnects, offering advantages like high bandwidth density, …

Electronics Design For Krepe Atmospheric Entry Capsule Avionics, Matt Ruffner

Theses and Dissertations--Electrical and Computer Engineering

This research documents the design, testing, and implementation of sensing, control, and communications subsystems for small atmospheric entry capsules. Atmospheric entry capsules pose a unique electronics design challenge given mission requirements, environmental constraints, and inherent risk involved in space based missions. Previous work on small satellites developed the CubeSat platform as a means of ensuring reliability after university-led small satellite missions experienced failures. The publication of the CubeSat platform allowed researchers to focus on the payload science utilizing a standardized form-factor and reusable electronics. Environmental and operational constraints of CubeSats and atmospheric entry capsules overlap and best-practices associated with building …

Mitigation Of Reflected Overvoltage In Wind-Turbine Generator-Converter Systems With A Smart Coil Concept, Lulu Wei

Theses and Dissertations--Electrical and Computer Engineering

In the recent decade, ultra-fast wide bandgap switching devices such as Silicon Carbide (SiC) Metal-Oxide-Semiconductor Field-Effect Transistors (MOSFETs) have been increasingly utilized in power electronic converters for renewable energy power generation systems due to their advantages of enabling high energy efficiency and high power density. However, the much higher voltage slew rate (i.e., dv/dt) with SiC power converters may induce voltage reflection and reliability concerns in machine-converter systems, especially for medium-voltage systems with long cable connections. In wind-turbine power generation systems, generators are typically located in the nacelles, and medium-voltage power converters are mostly placed at the bottom of the …

A Novel Processor Architecture Implementing The Stacked Error Diffusion Algorithm And Its Zynq-Based Realization, Qishi Hu

Theses and Dissertations--Electrical and Computer Engineering

Digital halftoning reproduces continuous-tone images using patterns of black and white dots, while multitoning extends this concept by incorporating inks with intermediate intensities. These techniques are extensively utilized in the printing industry to accommodate the limited range of inks available in printers. Stacked error diffusion is a high-quality multitoning algorithm that adheres to the blue-noise dithering standard. This thesis research studies the potential parallelism inherent in the algorithm and introduces the design of a novel processor architecture optimized for efficient execution. The architecture is realized on an FPGA development board featuring a Zynq SoC. Additionally, the hardware prototype can also …

Unmanned Aircraft Systems For Precision Meteorology: An Analysis Of Gnss Position Measurement Error And Embedded Sensor Development, Karla S. Ladino

Theses and Dissertations--Biosystems and Agricultural Engineering

The overarching objective of this research was to enhance our comprehension of the three-dimensional precision of meteorological measurements obtained using small unmanned aircraft systems (UAS). Two complimentary experiments were conducted to achieve this objective.

The first experiment entailed the development and implementation of a system to determine the global navigation satellite system (GNSS) position accuracy on a UAS platform. This system was utilized to assess the static and dynamic accuracy of L1 and L1/L2 GNSS receivers in real-time kinematic (RTK) and non-RTK fix modes. Adjusted two-sample t-tests revealed significant differences in horizontal and vertical error between RTK and non-RTK receivers …

Low-Cost Compact Optical Spectroscopy And Novel Spectroscopic Algorithm For Point-Of-Care Real-Time Monitoring Of Nanoparticle Delivery In Biological Tissue Models, Zahid Hasan, Jing Yan, Zhongchao Yi, Madison O. Korfhage, Sheng Tong, Caigang Zhu

Markey Cancer Center Faculty Publications

Objective: Real-time monitoring of nanoparticle delivery in biological models is essential to optimize nanoparticle- mediated therapies. However, few techniques are available for convenient real-time monitoring of nanoparticle concentrations in tissue samples. This work reported novel optical spectroscopic approaches for low-cost point-of-care real-time quantification of nanoparticle concentrations in biological tissue samples.

Methods: Fiber probe measured diffuse reflectance can be described with a simple analytical model by introducing an explicit dependence on the reduced scattering coefficient. Relying on this, the changes on the inverse of diffuse reflectance are proportional to absorption change when the scattering perturbation is negligible. We developed this model …

Laptop Recycling Case Study: Estimating The Contained Value And Value Recovery Process Feasibility Of End-Of-Life Consumer Electronics, Zebulon Hart

Theses and Dissertations--Mining Engineering

Work has been done to establish, through the development and use of novel assay techniques and analysis metrics, the contained value of a sampling of laptop computers (as an analog for myriad e-waste sources). This work has conceptualized e-waste as an alternative to geologic-origin complex metallic ores and has likewise evaluated the feasibility of value recovery from e-waste sources in a similar manner to an ore. The application of conventional and novel mineral separation techniques to e-waste recycling processes has been evaluated and positive results are demonstrated. Further, this work has demonstrated the ability to identify the presence of base …

Development Of Dc Circuit Breakers For Medium-Voltage Electrified Transportation, Trevor Morgan Arvin

Theses and Dissertations--Electrical and Computer Engineering

Medium-voltage DC (MVDC) distribution is an enabling technology for the electrification of transportation such as aircraft and shipboard. One main obstacle for DC distribution is the lack of adequate circuit fault protection. The challenges are due to the rapidly rising fault currents and absence of zero crossings in DC systems compared to AC counterparts. Existing DC breaker solutions lack comprehensive consideration of energy efficiency, power density, fault interruption speed, reliability, and implementation cost.

In this thesis, two circuit topologies of improved DC circuit breakers are developed: the resonant current source based hybrid DC breaker (RCS-HDCB) and the high temperature superconductor …

Parametric Average-Value Modeling, Simulation, And Characterization Of Machine-Rectifier Systems, Isuje Ojo

Theses and Dissertations--Electrical and Computer Engineering

There are many techniques for modeling and simulation of synchronous machine-rectifier systems. The more common approaches are the detailed and average-value modeling techniques. The detailed simulation technique takes into account the details of the diode switching and is both very accurate and very expensive in terms of computational resources. To alleviate this disadvantage, the average-value modeling technique is often utilized. In this approach, the details of diode switching are neglected or averaged. In that light, the work presented herein proposes a unique saliency-sensitive parametric average-value model (SSPAVM) of the synchronous machine-rectifier system. This model extends existing parametric average-value models to …

Suppressing Bias Stress Degradation In High Performance Solution Processed Organic Transistors Operating In Air, Hamna F. Iqbal, Qianxiang Ai, Karl J. Thorley, Hu Chen, Iain Mcculloch, Chad Risko, John E. Anthony, Oana D. Jurchescu

Chemistry Faculty Publications

Solution processed organic field effect transistors can become ubiquitous in flexible optoelectronics. While progress in material and device design has been astonishing, low environmental and operational stabilities remain longstanding problems obstructing their immediate deployment in real world applications. Here, we introduce a strategy to identify the most probable and severe degradation pathways in organic transistors and then implement a method to eliminate the main sources of instabilities. Real time monitoring of the energetic distribution and transformation of electronic trap states during device operation, in conjunction with simulations, revealed the nature of traps responsible for performance degradation. With this information, we …

Development Of A Hybrid-Electric Aircraft Propulsion System Based On Silicon Carbide Triple Active Bridge Multiport Power Converter, Cole M. Ivey

Theses and Dissertations--Electrical and Computer Engineering

Constrained by the low energy density of Lithium-ion batteries with all-electric aircraft propulsion, hybrid-electric aircraft propulsion drive becomes one of the most promising technologies in aviation electrification, especially for wide-body airplanes. In this thesis, a three-port triple active bridge (TAB) DC-DC converter is developed to manage the power flow between the turbo generator, battery, and the propulsion motor. The TAB converter is modeled based on the emerging Silicon Carbide (SiC) Metal-Oxide-Semiconductor Field Effect Transistor (MOSFET) modules operating at high switching frequency, so the size of the magnetic transformer can be significantly reduced. Different operation modes of this hybrid-electric propulsion drive …

Special Power Electronics Converters And Machine Drives With Wide Band-Gap Devices, Yibin Zhang

Theses and Dissertations--Electrical and Computer Engineering

Power electronic converters play a key role in power generation, storage, and consumption. The major portion of power losses in the converters is dissipated in the semiconductor switching devices. In recent years, new power semiconductors based on wide band-gap (WBG) devices have been increasingly developed and employed in terms of promising merits including the lower on-state resistance, lower turn-on/off energy, higher capable switching frequency, higher temperature tolerance than conventional Si devices. However, WBG devices also brought new challenges including lower fault tolerance, higher system cost, gate driver challenges, and high dv/dt and resulting increased bearing current in electric machines.

This …

Electric Power Systems And Components For Electric Aircraft, Damien Lawhorn

Theses and Dissertations--Electrical and Computer Engineering

Electric aircraft have gained increasing attention in recent years due to their potential for environmental and economic benefits over conventional airplanes. In order to offer competitive flight times and payload capabilities, electric aircraft power systems (EAPS) must exhibit extremely high efficiencies and power densities. While advancements in enabling technologies have progressed the development of high performance EAPS, further research is required.

One challenge in the design of EAPS is determining the best topology to be employed. This work proposes a new graph theory based method for the optimal design of EAPS. This method takes into account data surveyed from a …

Toward Intelligent Welding By Building Its Digital Twin, Qiyue Wang

Theses and Dissertations--Electrical and Computer Engineering

To meet the increasing requirements for production on individualization, efficiency and quality, traditional manufacturing processes are evolving to smart manufacturing with the support from the information technology advancements including cyber-physical systems (CPS), Internet of Things (IoT), big industrial data, and artificial intelligence (AI). The pre-requirement for integrating with these advanced information technologies is to digitalize manufacturing processes such that they can be analyzed, controlled, and interacted with other digitalized components. Digital twin is developed as a general framework to do that by building the digital replicas for the physical entities. This work takes welding manufacturing as the case study to …

Optimization Of Aggregated Ev Power In Residential Communities With Smart Homes, Huangjie Gong, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Electric vehicles (EVs) tend to increase peak power for residences in the evening when house owners return home and begin charging. The aggregated EV charging demand can cause a sudden rise in the peak power at the distribution system level, resulting in a “dragon curve” Such phenomenon, combined with the “duck curve” that is caused by high photovoltaic (PV) penetration in residential communities, requires fast ramping rates and expanded capabilities for local distribution transformers and main feeder cables provided by the utility. As a solution, a residential energy storage system (RESS) can store surplus PV generation during midday and use …

Rapid Prototyping Of Nanostructures With Electron Beam Induced Processing, Samaneh Esfandiarpour

Theses and Dissertations--Electrical and Computer Engineering

Focused electron beam induced processing (FEBIP) is a nano-scale fabrication technique that allows the direct deposition of functional materials. However, it suffers from significant drawbacks, such as high cost, low speed, unavailable precursors for many materials and low purity of deposits. Liquid-phase focused electron beam induced processes (LP-FEBIP) are being investigated due to the potential benefits over the gas phase technique. In this method, deposition or etching occurs at the interface between a substrate and a bulk liquid. In this work, electron beam induced deposition of copper nanostructures from aqueous solutions of copper sulfate is demonstrated. The addition of sulfuric …

End-To-End Prediction Of Weld Penetration In Real Time Based On Deep Learning, Wenhua Jiao

Theses and Dissertations--Electrical and Computer Engineering

Welding is an important joining technique that has been automated/robotized. In automated/robotic welding applications, however, the parameters are preset and are not adaptively adjusted to overcome unpredicted disturbances, which cause these applications to not be able to meet the standards from welding/manufacturing industry in terms of quality, efficiency, and individuality. Combining information sensing and processing with traditional welding techniques is a significant step toward revolutionizing the welding industry. In practical welding, the weld penetration as measured by the back-side bead width is a critical factor when determining the integrity of the weld produced. However, the back-side bead width is difficult …

Resource Efficient Design Of Quantum Circuits For Cryptanalysis And Scientific Computing Applications, Edgard Munoz-Coreas

Theses and Dissertations--Electrical and Computer Engineering

Quantum computers offer the potential to extend our abilities to tackle computational problems in fields such as number theory, encryption, search and scientific computation. Up to a superpolynomial speedup has been reported for quantum algorithms in these areas. Motivated by the promise of faster computations, the development of quantum machines has caught the attention of both academics and industry researchers. Quantum machines are now at sizes where implementations of quantum algorithms or their components are now becoming possible. In order to implement quantum algorithms on quantum machines, resource efficient circuits and functional blocks must be designed. In this work, we …

Fabrication And Characterization Of Planar-Structure Perovskite Solar Cells, Guoduan Liu

Theses and Dissertations--Electrical and Computer Engineering

Currently organic-inorganic hybrid perovskite solar cells (PSCs) is one kind of promising photovoltaic technology due to low production cost, easy fabrication method and high power conversion efficiency.

Charge transport layers are found to be critical for device performance and stability. A traditional electron transport layer (ETL), such as TiO₂ (Titanium dioxide), is not very efficient for charge extraction at the interface. Compared with TiO₂, SnO₂ (Tin (IV) Oxide) possesses several advantages such as higher mobility and better energy level alignment. In addition, PSCs with planar structure can be processed at lower temperature compared to PSCs with …

Mathematical Programming Approach For The Design Of Satellite Power Systems, Allen Flath Iii

Theses and Dissertations--Electrical and Computer Engineering

Satellite power systems can be understood as islanded dc microgrids supplied by specialized and coordinated solar cell arrays augmented by electrochemical battery systems to handle high-power loads and periods of eclipse. The periodic availability of power, the limited capacity of batteries, and the dependence of all mission service on power consumption create a unique situation in which temporal power and energy scarcity exist. A multi-period model of an orbital satellite power system’s performance over a mission’s duration can be constructed. A modular power system architecture is used to characterize the system’s constraints. Using mathematical programming, an optimization problem can be …

Curricular Optimization: Solving For The Optimal Student Success Pathway, William G. Thompson-Arjona

Theses and Dissertations--Electrical and Computer Engineering

Considering the significant investment of higher education made by students and their families, graduating in a timely manner is of the utmost importance. Delay attributed to drop out or the retaking of a course adds cost and negatively affects a student’s academic progression. Considering this, it becomes paramount for institutions to focus on student success in relation to term scheduling.

Often overlooked, complexity of a course schedule may be one of the most important factors in whether or not a student successfully completes his or her degree. More often than not students entering an institution as a first time full …

Optimum Design Of Axial Flux Pm Machines Based On Electromagnetic 3d Fea, Narges Taran

Theses and Dissertations--Electrical and Computer Engineering

Axial flux permanent magnet (AFPM) machines have recently attracted significant attention due to several reasons, such as their specific form factor, potentially higher torque density and lower losses, feasibility of increasing the number of poles, and facilitating innovative machine structures for emerging applications. One such machine design, which has promising, high efficiency particularly at higher speeds, is of the coreless AFPM type and has been studied in the dissertation together with more conventional AFPM topologies that employ a ferromagnetic core.

A challenge in designing coreless AFPM machines is estimating the eddy current losses. This work proposes a new hybrid analytical …

Performance Evaluation Of Energy-Autonomous Sensors Using Power-Harvesting Beacons For Environmental Monitoring In Internet Of Things (Iot), George Dan Moiş, Teodora Sanislav, Silviu Corneliu Folea, Sherali Zeadally

Information Science Faculty Publications

Environmental conditions and air quality monitoring have become crucial today due to the undeniable changes of the climate and accelerated urbanization. To efficiently monitor environmental parameters such as temperature, humidity, and the levels of pollutants, such as fine particulate matter (PM2.5) and volatile organic compounds (VOCs) in the air, and to collect data covering vast geographical areas, the development of cheap energy-autonomous sensors for large scale deployment and fine-grained data acquisition is required. Rapid advances in electronics and communication technologies along with the emergence of paradigms such as Cyber-Physical Systems (CPSs) and the Internet of Things (IoT) have led to …

Scheduling Based On Interruption Analysis And Pso For Strictly Periodic And Preemptive Partitions In Integrated Modular Avionics, Hui Lu, Qianlin Zhou, Zongming Fei, Rongrong Zhou

Computer Science Faculty Publications

Integrated modular avionics introduces the concept of partition and has been widely used in avionics industry. Partitions share the computing resources together. Partition scheduling plays a key role in guaranteeing correct execution of partitions. In this paper, a strictly periodic and preemptive partition scheduling strategy is investigated. First, we propose a partition scheduling model that allows a partition to be interrupted by other partitions, but minimizes the number of interruptions. The model not only retains the execution reliability of the simple partition sets that can be scheduled without interruptions, but also enhances the schedulability of the complex partition sets that …