Electrical and Electronics Commons^™

Me3329 Modular Phonograph Gearbox, Garrett Andrik Leighton, Preston Robert Hupe, Gavin Carter Ebner, Andrew Renato Reyes

Mechanical Engineering

The Mechanical Engineering Department at California Polytechnic State University, San Luis Obispo (Cal Poly), seeks to develop a laboratory tool allowing students to reinforce concepts of gears for Mechanical Systems Design (ME329). Some current laboratories do not provide students with hands-on interaction, and the department lacks equipment and documentation to support a standardized lab. With ME329 expanding from ten to fifteen weeks, there is an opportunity to create a physical gearbox design lab allowing students to reinforce lecture material in engaging ways, while standardizing student learning. This senior project is presented and sponsored by Professor Alan Zhang. It will be …

Custom Animatronic Puppet, Jake Schuman, Fredy Herrarte, Madison Reedy, Jackson Reynolds

Mechanical Engineering

This project involved the design, fabrication, and implementation of a custom audio-animatronic puppet modeled after Dr. Brian Davis for the California Polytechnic State University Mechanical Engineering Department. The objective was to create an expressive, lifelike character capable of synchronized speech, head movement, arm gestures, and seated-to-standing motion while demonstrating the integration of mechanical design, controls, manufacturing, and artistic fabrication.

The final system consists of an 18-degree-of-freedom animatronic platform utilizing servo-driven facial and upper-body actuation combined with a pneumatic standing mechanism. A modular aluminum and 3D-printed structural framework was developed using SolidWorks and validated through engineering analysis. Character shells were digitally …

Implantable, Sensor-Embedded Vascular Graft Towards Wireless Monitoring Of Stenosis, Nnamdi Dike

LSU Master's Theses

Arteriovenous (AV) grafts are commonly used to provide vascular access for hemodialysis in patients with end-stage renal disease. Despite their widespread use, AV grafts are prone to complications such as stenosis and thrombosis. Early detection of these conditions remains challenging with current monitoring methods too costly or insufficient. This work presents the design, fabrication, and validation of an LC pressure sensor embedded within a model AV graft to enable real-time monitoring. The proposed system integrates a parallel-plate capacitive pressure sensor with a spiral inductor to form an LC circuit embedded within an elastomeric graft wall. The Ecoflex 00-30 dielectric layer …

Automation And Habitat Development For A Space Based Marine Life Environment, Logan Trimmer, Alexander Hang

Harrisburg University Other Works

This project was a cross-collaboration between the Environmental Sciences and Advanced Manufacturing and Robotics programs for the company Monolith Space.

The goal of this project was to design an autonomous system to be able to track qualities of water in an aquaculture system designed to be sent to space.

A Review Of Lithium-Ion Battery Capacity Fade Deceleration At Power Fluctuations In Renewable Energy Systems, Isaac Gwayi

Tanzania Journal of Engineering and Technology (TJET)

Application of lithium-ion (Li-ion) batteries to store energy in renewable energy systems (RESs) is increasing due to their promising properties. Therefore, it is crucial to understand aging behaviours of Li-ion battery during RES life time as this directly affects cost of energy. Li-ion battery aging can be categorised into calendar aging and cycle aging. Calendar aging depends mainly on temperature and state of charge (SoC). In addition to temperature and SoC, cycle aging depends also on charge and discharge current rates and cut-off voltages. Higher current rates lead to faster Li-ion battery aging. It is necessary to identify appropriate battery …

Optimal Placement Of Distributed Generation Units In Power Distribution Networks Using Particle Swarm Optimization, Owdean M. Suwi

Tanzania Journal of Engineering and Technology (TJET)

Power losses and voltage drops in distribution networks are critical issues in power system operation, reducing efficiency, reliability, and overall quality of the power supply to customers. Additionally, the rising electricity demand, deregulation of energy markets, and congestion in transmission networks have further contributed to the declining performance of the grid. To address these challenges, integrating distributed generation units (DGUs) into electric distribution systems has gained significant attention. Furthermore, the integration of DGUs into conventional fossil fuel-based power plants is becoming necessary to reduce greenhouse gas emissions. However, proper placement and sizing of DGUs are crucial for achieving optimal benefits. …

Calibration Of Measurement Tools In The Experimental Test Rig For Hydropower Performance Evaluation, Ombeni J. Mdee

Tanzania Journal of Engineering and Technology (TJET)

The demonstration of a typical hydropower plant requires the development of a test rig with the installation of tools to measure the performance parameters. The measurement tools require a calibration process to improve the quality of recorded data. This study involved the calibration of traditional and automated measurement tools connected to the hydropower test rig through an Arduino microprocessor. The automated measurement tools included a pressure transducer, flow meter, digital tachometer, and torque transducer, while traditional measurement tools, including a pressure gauge, concrete water tank, contact tachometer, and force lever arm balance, were connected in the same test rig during …

Pressure Switch Tester, Michael Starasinich, Andrew Dobson, Jordan Huschen, Mitchell Smith, Melvin Brown Iii

Honors Capstones

Abstract—- The Pressure Switch Test Stand is a comprehensive and automated testing solution designed to streamline the actuation and validation of simultaneously. At the core of the system is a PLC-controlled architecture that enables precise control and simulation of pressure conditions, replicating real-world scenarios to ensure accurate and reliable switch performance.

This test stand integrates robust mechanical fixtures, a reliable pneumatic control system, custom-designed electrical circuits, and a modular software interface, working in unison to deliver consistent and high-fidelity testing outcomes. Each pressure switch undergoes a sequence of pressure ramps and holds, with the system continuously monitoring switch states, activation …

Development Of A Cost-Effective Daq For Measuring Brake Performance In Race Cars, Adrin Alias

2025 Spring Honors Capstone Projects - Archive

This project explores the feasibility of creating a cost-effective data acquisition (DAQ) system for high-speed, real-time brake performance testing of Formula SAE racecars. The research addresses the limitations of the current MoTeC DAQ system currently employed by the team, which is costly and time-consuming to set up for on-car testing. The team will use a brake dynamometer for steady-state comparisons of different brake pad compounds (senior design project), but evaluating real-world performance requires on-car testing. By systematically comparing various hardware platforms, sensors, communication protocols, and storage solutions, this project aims to balance cost-efficiency with reliability and performance. The research evaluates …

Validating An Electronics Cooler Experiment And Optimizing Its Performance Using Ansys Icepak, Daniel V. Curl

Mechanical Engineering Undergraduate Honors Theses

Researchers at the University of Arkansas' Mechanical and Electrical Engineering Research Departments have designed and built a cold plate and substrate design for a 10 kV SiC MOSFET power module. Many variables define the design of the cold plate and substrate system and have quantifiable effects on the device’s performance. These variables include but are not limited to geometry and material selection of the fins and substrate. Manufacturing many test designs, running experiments, and comparing their performance is a time-consuming and expensive design optimization method that may be effective for some low-cost applications. Still, simulation is often a more cost-effective …

Synthetic Inertia Provision For Load Frequency Control In Networks With High Penetration Of Renewable Energy Sources, Paulina Mkoi

Tanzania Journal of Engineering and Technology (TJET)

The integration of renewable energy sources (RESs) such as solar photovoltaic (PV) and wind energy has become a promising solution as the world shifts toward clean energy. Solar PV and wind resources are increasingly replacing conventional synchronous generators, leading to reduced system inertia and increased vulnerability to frequency instability during disturbances. To address this challenge, this study proposes a novel synthetic inertia provision strategy using a battery energy storage system (BESS) integrated alongside solar PV. The proposed method dynamically compensates for the loss of inertia by considering the variability of solar PV output due to changes in irradiance and temperature. …

Efficient Operation Of Direct Coupled Solar Home Pv System: A Case Of Solar Home Pv System Installed In Dodoma, Tanzania, Sarah P. Ayeng'o

Tanzania Journal of Engineering and Technology (TJET)

Direct coupled Photovoltaic (PV) system is a common topology among most of the off-grid communities in the world. This topology has less components hence resulting in low investment costs. However, it suffers much losses when battery operating voltage is far from maximum power point voltage of PV modules. This scenario can be attributed by different factors such as; variation in solar radiation, load profile and temperature. Efficient operation of these systems is required in order to reduce losses. Usually in direct coupled system, PV modules are connected in parallel with batteries through a charge controller hence making PV output to …

3d Printed Microfluidic Fabrication Methodology, Characterization, Mechanical Design, And Applications In Electrostatic Artificial Muscles And Benthic Microbial Fuel Cells, Terak B. Hornik

Master's Theses

The fabrication of microfluidic devices often requires specialized methods. The development of these methods requires careful characterization and understanding of the processes involved. Using primarily PolyJet 3D printing technology, microfluidics offers a wide scope of applications such as microfluidic benthic microbial fuel cells (MBMFCs) and electrostatic artificial muscles. MBMFCs benefit from the confinement of the microbes resulting in close proximity between the electrode and the organisms. Using a modular design called the Sponge, assembly and upscaling is possible. Electrostatic artificial muscles benefit from a microfluidic approach due to the non-linearity of electrostatic attraction creating disproportionate benefits when miniaturized. When designed …

Design And Implementation Of An Inverted Short Baseline Acoustic Positioning System, Jakob Frabosilio

Master's Theses

This document details the design, implementation, testing, and analysis of an inverted short baseline acoustic positioning system. The system presented here is an above-water, air-based prototype for an underwater acoustic positioning system; it is designed to determine the position of remotely-operated underwater vehicles (ROVs) and autonomous underwater vehicles (AUVs) in the global frame using a method that does not drift over time.

A ground-truth positioning system is constructed using a stacked hexapod platform actuator, which mimics the motion of an AUV and provides the true position of an ultrasonic microphone array. An ultrasonic transmitter sends a pulse of sound towards …

Electophorectic Deposition For Novel Nanodecorated Electrodes Towards Thermally Charging Supercapacitor (Tcsc), Ashish Thakur

Mechanical and Aerospace Engineering Theses - Archive

Thermally Self-Charging Supercapacitors (TSCS) are a promising new technology that can harvest waste heat to produce electrical energy. The Soret effect is exploited wherein ion separation due a temperature gradient leads to a potential difference. Here, we use electrophoretic deposition (EPD), a room-temperature, scalable, universal technique, to obtain CNT decorated electrodes for fabrication of such TSCS devices with ionic liquid electrolyte. We further show that precise control over deposition parameters can be used for optimization of TSCS performance metrics. TSCS devices were tested by several characterization standards, indicating the superior performance of nanodecorated electrodes obtained by EPD.

Development And Application Of Guided Mode Resonance Biosensor Platforms For Highly Sensitive And Real-Time Cell Killing Assays, Seyedmohsen Vaziri

Electrical Engineering Dissertations - Archive

In this work, we developed and investigated the cancer cell killing efficacy of different instances using real-time high-sensitivity measurements facilitated by Guided-Mode Resonance (GMR) sensors. The GMR biosensor technology detects shifts in the spectral peak caused by changes in the refractive index of the surrounding medium, offering a label-free method for monitoring cellular events.

A549 cell line wild type and HER2 knockout (lung cancer cells) were exposed to different concentrations of Triton X-100 and ADC (Herceptin with αHFc-CL-DMDM). The GMR-based cell killing assay demonstrated exceptional sensitivity and specificity, with shifts in wavelength exhibiting a robust correlation with cell viability and …

Fabrication Of Smooth Sac305 Thin Film Via Magnetron Sputtering, M. Ojha, A. A. Elmustafa

Mechanical & Aerospace Engineering Faculty Publications

SAC305 (96.5 wt% Sn, 3 wt% Ag, 0.5 wt%Cu) solder is increasingly becoming popular due to its reliability good characteristics and performance in addition to the environmental concerns and regulations that restrict the use of lead in nano/microelectronic products. In nano/microelectronics, manufacturing smooth solder coatings free of defects such as voids and cracks, which can compromise joint reliability is crucial. Magnetron sputtering offers a high degree of control over film thickness and composition, resulting in films with excellent uniformity and adhesion. Despite these advantages, fabricating continuous and robust SAC305 films using magnetron sputtering remains a difficult task with limited research …

Functional Verification Of Additively Manufactured Metallopolymer Structures For Structural Electronics Design, Nathan D. Singhal

Honors Undergraduate Theses

As an attempt to improve the overall cost-effectiveness and ease of structural electronics manufacturing, this study characterizes the mechanical and electrical responses of structures which are fabricated from a novel metallopolymer composite material by fused deposition modeling as they are subjected to quasi-static, uniaxial mechanical tension. Baseline values of tensile properties and electrical resistivity were first obtained via ASTM D638-22 standard testing procedures and linear sweep voltammetry (LSV), respectively. A hybrid procedure to measure in-situ mechanically dependent electrical behavior was subsequently developed and implemented. The mechanical and electromechanical testing was followed by the derivation of stochastic values for several mechanical …

Design, Fabrication And Characterization Of Zero Power Sensor/Harvester For Smart Grid Applications, Zeynel Guler

Mechanical Engineering ETDs

This study presents a flexible sensor/harvester device to be used in both electromagnetic sensing and energy harvesting applications for smart grids. When a current passes through a wire, the sensor detects the magnetic field created by that current. The sensor magnet interacts with the wire magnetic field resulting in a transfer of energy through the piezoelectric cantilever. Piezoelectric, conductive, magnetic, and magnetostrictive composite thin films were prepared to fabricate this device.

Initially, the magnet of the cantilever was optimized considering its shape, thickness, length, taper angle etc. via both simulations and experiments. Peak to peak voltage versus cantilever position graph …

Gpu Based Monte Carlo Estimation Of Eddy Current Losses In Electromagnetic Coil-Core System, Adwaith Ravichandran

Theses and Dissertations

A novel parallelizable probabilistic approach to model eddy currents in AC electromagnets is presented in this research. Consequently, power loss associated with the formation of these eddy currents is estimated and validated using experimental data. Furthermore, predicting the effect of ferromagnetic alternating field enhancement on power loss in the source excitation winding has been an active area of research. Unlike a stationary field, an alternating sinusoidal field diffuses partially into the ferromagnetic material leading to a predictably sub-optimal field enhancement. To model these physics, finite element techniques employ nonlinear iterative solvers which are time consuming. A novel method is developed …

Investigating Mems Devices In Flow Conditions Relevant To Flow-Through Systems., Mohammad Shafquatul Islam

Electronic Theses and Dissertations

Advancements in microscale actuating technologies has substantially expanded the possibilities of interacting with the surrounding environment. Microstructures that deflect in response to mechanical forces are one of the largest application areas of microelectromechanical systems (MEMS). MEMS devices, functioning as sensors, actuators, and support structures, find applications in inertial sensors, pressure sensors, chemical sensors, and robotics, among others. Driven by the critical role of catalytic membrane reactors, this dissertation aims to evaluate enzyme activity on polymeric membranes and explore how fabrication methods from the field of Electrical and Computer Engineering (ECE) can incorporate sensing and actuation into these porous surfaces. Toward …

Implementation Of Static Rfid Landmarks In Slam For Planogram Compliance, Brennan L. Drake

Honors College Theses

Autonomous robotic systems are becoming increasingly prevalent in everyday life and exhibit robust solutions in a wide range of applications. They face many obstacles with the foremost of which being SLAM, or Simultaneous Localization and Mapping, that encompasses both creation of the map of an unknown environment and localization of the robot in said environment. In this experiment, researchers propose the use of RFID tags in a semi-dynamic commercial environment to provide concrete landmarks for localization and mapping in pursuit of increased locational certainty. With this obtained, the ultimate goal of the research is to construct a robotics platform for …

Topologically Optimized Electrodes For Electroosmotic Actuation, Jianwen Sun, Jianyu Zhang, Ce Guan, Teng Zhou, Shizhi Qian, Yongbo Deng

Mechanical & Aerospace Engineering Faculty Publications

Electroosmosis is one of the most used actuation mechanisms for the microfluidics in the current active lab-on-chip devices. It is generated on the induced charged microchannel walls in contact with an electrolyte solution. Electrode distribution plays the key role on providing the external electric field for electroosmosis, and determines the performance of electroosmotic microfluidics. Therefore, this paper proposes a topology optimization approach for the electrodes of electroosmotic microfluidics, where the electrode layout on the microchannel wall can be determined to achieve designer desired microfluidic performance. This topology optimization is carried out by implementing the interpolation of electric insulation and electric …

Enhancing Traffic Safety In Unpredicted Environments With Integration Of Adas Features With Sensor Fusion In Intelligent Electric Vehicle Platform With Implementation Of Environmental Mapping Technology, David S. Obando Ortegon

College of Graduate Studies: Theses & Dissertations

A major objective on society is to reduce the number of accidents and fatalities on the road for drivers, and pedestrians. Therefore, the automotive engineering field is working on this problem through the development and integration of safety technologies such as advanced driving assistance systems. For this reason, this work was intended to develop and evaluate the performance of different ADAS features and IV technologies under unexpected scenarios. This by the development of safety algorithms applied to the intelligent electric vehicle designed and built in this work, through the use of ADAS sensors based on sensor fusion. Evaluation of AEB, …

Development Of Method To Characterize Adhesion Of Electrically Conductive Adhesive For Flexible Electronics, Joshua Corbin

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

An Iot Based Worker Safety Helmet Using Cloud Computing Technology, Yuthriya Iddi Khamis, Mahmoud Alawi, Waheed Muhammad Sanya

Tanzania Journal of Engineering and Technology (TJET)

Miner safety and security is a major challenge around the world due to the exposure to toxic gases that are frequently released in underground mines. Miners' health is adversely affected primarily by toxic gases, which endanger the workers' lives. Furthermore, human sensory abilities do not detect these dangerous gases. As a result, this paper proposes a safety monitoring system that includes a temperature sensor, humidity sensor, and gas sensors to detect harmful gases and alert miners to those harmful gases using the smart helmet they wear. These gases are transmitted to the control station via the cloud using Internet of …

Machine Learning Approach For Classifying Power Outage In Secondary Electric Distribution Network, Stephan Mgaya, Hellen Maziku

Tanzania Journal of Engineering and Technology (TJET)

Power outage is the problem that hinders social and economic development especially for developing countries like Tanzania. Frequent power outages damage electric equipment, and negatively affect the industrial production process. Power outages cannot be completely eradicated due to uncontrolled cause like natural calamities but technical challenges can be managed and hence reducing power outages. The existing manual methods used to locate power outage like customer calls is inefficient and time consuming. On the other hand, modern method like the Advanced Metering Infrastructure (AMI) still faces a challenge in effectively classifying power line outage due to the nature of imbalanced datasets. …

Group-Based Data Offloading Techniques Assisted By D2d Communication In 5g Mobile Network, Juma S Ally

Tanzania Journal of Engineering and Technology (TJET)

Machine type communication devices proposed as one of the substantial data collections in the 5G of wireless networks. However, the existing mobile communication network is not designed to handle massive access from the MTC devices instead of human type communication. In this context, we propose the device-to-device communication assisted a mobile terminal (smartphone) on data computing, focusing on data generated from a correlated source of machine type communication devices. We consider the scenario that the MTC devices after collecting the data will transmit to a smartphone for computing. With the limitation of computing resources at the smartphone, some data are …

Efficient And Simple Heuristic Algorithm For Portfolio Optimization Collether John, Collether John

Tanzania Journal of Engineering and Technology (TJET)

Markowitz model considers what is termed as standard portfolio optimization. The portfolio optimization problem is a problem which based on asset allocation and diversification for maximum return with minimum risk. Thus, the standard portfolio optimization problem happens when the constraints considered are budget and no-short selling. In reality however, portfolio optimization has realistic constraints to be incorporated such as holding sizes, cardinality and transaction cost. When realistic constraints are added into portfolio optimization problem, it becomes too complex to be solved by standard optimization methods which in this case turns to be an extended portfolio optimization problem. Markowitz solution and …

An Experimental Approach Towards Pv-Based Solar System Sizing For An Engineering Laboratory, Muyideen O. Lawal

Tanzania Journal of Engineering and Technology (TJET)

This study aims at providing an experimental sizing procedure for a rooftop PV-based solar power system for an engineering laboratory. This was achieved by monitoring the peak power and energy delivered by an installed 20W solar panel into an 18 Ah battery. Knowledge of the average daily peak power and energy was used to determine the percentage rated capacity available for use and the sun hour. A load consumption comparison was also carried out with and without the connection of a load to inverter. In addition to this, the monitoring of the no-load consumption of the inverter was carried out. …