Electrical and Electronics Commons^™

Vision Based Real-Time Monitoring And Control Of Metal Transfer In Laser Enhanced Gas Metal, Yan Shao

Theses and Dissertations--Electrical and Computer Engineering

Laser enhanced gas metal arc welding (GMAW) is a novel welding process where a laser is applied to provide an auxiliary detaching force to help detach the droplet such that welds may be made in gas tungsten arc welding high quality at GMAW high speeds. The current needed to generate the electromagnetic (detaching) force is thus reduced. The reduction in the current helps reduce the impact on the weld pool and over-heat fumes/smokes. However, in the previous studies, a continuous laser is applied. Since the auxiliary is only needed each time the droplet needs to be detached and the detachment …

Power Control Of Single-Stage Pv Inverter For Distribution System Volt-Var Optimization, Xiao Liu

Theses and Dissertations--Electrical and Computer Engineering

The output power variability of intermittent renewable sources can cause significant fluctuations in distribution system voltages. A local linear controller that exploits the capability of a photovoltaic inverter to provide both real and reactive power is described. This controller substitutes reactive power for real power when fluctuations in the output of the photovoltaic source are experienced. In this way, the inverter can help mitigate distribution system voltage fluctuations. In order to provide real and reactive to the grid, a three-phase grid-connected single-stage photovoltaic system with maximum power point tracking and power control is described. A method of reducing the current …

Tunable Fano Resonances Based On Two-Beam Interference In Microring Resonator, Ting Hu, Ping Yu, Chen Qui, Huiye Qui, Fan Wang, Mei Yang, Xiaoqing Jiang, Hui Yu, Jianyi Yang

Electrical & Computer Engineering Faculty Research

In this paper, a resonant system is demonstrated on silicon-on-insulator wafer to achieve tunable Fano resonances. In this system, the Fano resonance originates from the interference of two beams resonant in the microring resonator. The shapes of the Fano resonances are tunable through controlling the phase difference of the two beams. Both large slope and high extinctionratio (ER) are obtained when the phase difference is 0.5π or 1.5π. Experimental results show that Fano resonances with steep slope and ER over 20 dB are achieved in the whole free spectral range by controlling the microheaters to meet the phase condition.

Estimation Of Performance Indices For The Planning Of Sustainable Transportation Systems, Alexander Paz, Pankaj Maheshwari

Electrical & Computer Engineering Faculty Research

In the context of sustainable transportation systems, previous studies have either focused only on the transportation systemor have not used a methodology that enables the treatment of incomplete, vague, and qualitative information associated with the available data. This study proposes a system of systems (SOS) and a fuzzy logic modeling approach. The SOS includes the Transportation, Activity, and Environment systems. The fuzzy logic modeling approach enables the treatment of the vagueness associated with some of the relevant data. Performance Indices (PIs) are computed for each system using a number of performance measures. The PIs illustrate the aggregated performance of each …

Framework For Simulation Of Heterogeneous Mpsoc For Design Space Exploration, Bisrat Tafesse, Venkatesan Muthukumar

Electrical & Computer Engineering Faculty Research

Due to the ever-growing requirements in high performance data computation, multiprocessor systems have been proposed to solve the bottlenecks in uniprocessor systems. Developing efficient multiprocessor systems requires effective exploration of design choices like application scheduling, mapping, and architecture design. Also, fault tolerance in multiprocessors needs to be addressed. With the advent of nanometer-process technology for chip manufacturing, realization of multiprocessors on SoC (MpSoC) is an active field of research. Developing efficient low power, fault-tolerant task scheduling, and mapping techniques for MpSoCs require optimized algorithms that consider the various scenarios inherent in multiprocessor environments. Therefore there exists a need to develop …

Elec 2110: Elements Of Electrical Engineering—A Peer Review Of Teaching Project Benchmark Portfolio, Mahmoud Alahmad

UNL Faculty Course Portfolios

I have been teaching this class for the last five years. As an introductory course to electrical engineering, there is a lot of material that needs to be covered. All the material is important and relevant, and I try to go in-depth in each topic area. This approach has resulted in overwhelming the students and made them struggle with the course content, application and utilization. As I consider this course for the peer review, I am evaluating the depth of each topic and the opportunity to adjust the approach and method used to introduce new concepts and at the same …

Non-Uniform Transmission Lines For Ultra Wideband: Design Optimisation And Interfacing To Antennas And Loads, Prasanth Moolakuzhy Narayanan

Theses

This thesis presents the electrical characterization of ultra-wideband non- uniform transmission lines (UWB NUTLs). Non-uniform transmission lines have been identified as a successful device for ultra-wideband pulse shaping, which can be designed to generate complex and arbitrary pulse shapes as an impulse response. The performance of a range of UWB NUTLs, with different substrate materials and load impedances, has been characterised. In addition, the possibility of interfacing NUTL with antennas and the filtering effect of antennas has been investigated. To characterise the NUTLs, knowledge of current literature related to NUTL designs is required. A detailed review of the literature published …

Integration Of Memristors With Mems For Dynamic Displacement Control, Sergio Fabian Almeida Loya

Open Access Theses & Dissertations

In recent years the demand for high-speed, lower power consumption and large-capacity non-volatile memories has increased. Promisingly the memristor can be used due to its special characteristic of having memory through resistance change. The memristor behavior is not limited to digital applications but it can be used in analog application as well including: memristors in chaotic circuits, amoeba's learning, neural synaptic emulation, reprogrammable and reconfigurable circuits, and for neuromorphic computers. On the other hand Micro Electro Mechanical Systems (MEMS) are small scale structures that can interact with the physical world due to their mechanical properties. These devices are widely used …

Reduction Of Onu Buffering For Pon/Vdsl Hybrid Access Networks, Elliott Ivan Gurrola

Open Access Theses & Dissertations

Today's growing internet traffic requires service providers to offer customers faster transmission rates. To keep up with such high transmission rates, service providers need to deploy fiber optical networks. However, due to the high cost involved in deploying the fiber media, this may not prove to be a feasible solution. Instead, service providers can deploy fiber media up to a distribution point, such as a customer's block, and continue the last few hundred feet using the already deployed legacy copper wire media.

In our study we investigate downstream/upstream transmission coordination for passive optical network (PON) / Digital Subscriber Line (DSL) …

Structural, Optical And Electrical Properties Of Yttrium-Doped Hafnium Oxide Nanocrystalline Thin Films, Abhilash Kongu

Open Access Theses & Dissertations

Hafnium oxide (HfO2) has emerged as the most promising high-k dielectric for Metal-Oxide-Semiconductor (MOS) devices and has been highlighted as the most suitable dielectric materials to replace silicon oxide because of its comprehensive performance. In the present research, yttrium-doped HfO2 (YDH) thin films were fabricated using RF magnetron sputter deposition onto Si (100) and quartz with a variable thickness. Cross-sectional scanning electron microscopy coupled with Filmetrics revealed that film thickness values range from 700 A° to 7500 A°. Electrical properties such as AC Resistivity and current-voltage (I-V) characteristics of YDH films were studied. YDH films that were relatively thin (<1500 A°) crystallized in monoclinic phase while thicker films crystallized in cubic phase. The band gap (Eg) of the films was calculated from the optical measurements. The band gap was found to be ∼5.60 eV for monoclinic while it is ∼6.05 eV for cubic phase of YDH films. Frequency dependence of the electrical resistivity (ρac) and the total conductivity of the films were measured. Resistivity decreased (by three orders of magnitude) with increasing frequency from 100 Hz to 1 MHz, attributed due to the hopping mechanism in YDH films. Whereas, while ρac∼1Ω-m at low frequencies (100 Hz), it decreased to ∼ 104 Ω-cm at higher frequencies (1 MHz). Aluminum (Al) metal electrodes were deposited to fabricate a thin film capacitor with YDH layer as dielectric film thereby employing Al-YDH-Si capacitor structure. The results indicate that the capacitance of the films decrease with increasing film thickness. A detailed analysis of the electrical characteristics of YDH films is presented.

Assessment And Evaluation Of The Dynamic Behavior Of Muscles With Special Reference To Subjects With Diabetes Mellitus, Jorge Garza-Ulloa

Open Access Theses & Dissertations

Diabetes mellitus (simply diabetes) is a group of metabolic diseases in which a person has high blood sugar, either because the body does not produce enough insulin, or because cells do not respond to the insulin that is produced. Each year, the costs of diabetes rise. Diabetes and its complications cost our national economy. Two new methods are proposed to measure the diabetes implications in the muscles of lower body: Muscle energy expenditure analysis based on the detection of muscle transition-to-fatigue, and Natural Fuzzy logic method for differential analysis in muscle/joint. Then the results are compared with the traditional method …

Anasic Design And Test Methodology For An Undergraduate Design And Fabrication Project, Arun Joseph Kurian

Open Access Theses & Dissertations

During the 1990's the main focus of chip design methodologies was on the timings and area constraints. Power consumption was considered significant only after a drastic increase of device densities from 130nm on as well as dramatic increases in sub threshold leakage. As technology advanced from 130nm to 90nm and below there was a significant increase in leakage current due to lower threshold voltage and the influence of the deep submicron effects. High power consumption causes different problems such as increasing the cost of the product, reducing the reliability, reducing the battery life among others. Therefore EDA tools were designed …

Efficient, Scalable, Parallel, Matrix-Matrix Multiplication, Enrique Portillo

Open Access Theses & Dissertations

For the past decade, power/energy consumption has become a limiting factor for large-scale and embedded High Performance Computing (HPC) systems. This is especially true for systems that include accelerators, e.g., high-end computing devices, such as Graphics Processing Units (GPUs), with terascale computing capabilities and high power draws that greatly surpass that of multi-core CPUs. Accordingly, improving the node-level power/energy efficiency of an application can have a direct and positive impact on both classes of HPC systems.

The research reported in this thesis explores the use of software techniques to enhance the execution-time and power-consumption performance of applications executed on a …

Asynchronous Logic Design With Increased Fault Tolerance And Optimized For Subthreshold Operation, Ivan Santos

Open Access Theses & Dissertations

Synchronization has always been an essential feature in electronic circuits, in which functionality is achieved by an appropriate flow of data with respect to time. An ideal concept of logic design would require every operation to happen instantly; however, the application of this principle to electronics is governed by the laws of physics, which influence the time to execute a process. In fact, the speed at which a microprocessor can perform logic operations is determined by the time that charging and discharging capacitive loads requires, and the time that electric signals spend when traveling through the circuitry. Consequently, the variation …

3d Printed Impedance Elements By Micro-Dispensing, Ubaldo Robles Dominguez

Open Access Theses & Dissertations

Micro-dispensing allows electric circuits to be "3D printed," which can be used to give 3D printed systems electronic and electromagnetic functionality. The focus of this thesis is using micro-dispensing to fabricate capacitors and inductors. 3D printed impedance elements are capable of being more easily embedded, can be used to create structural electronics, and will have extensive applications in antennas, metamaterials, frequency selective surfaces, and more. This is the first known effort to print and measure impedance elements by micro-dispensing which holds great potential for manufacturing multi-material devices.

Analysis Of Vehicle Interactions On Interstate Highways: Discrete Choice And Linear System Approaches, Alicia Romo

Open Access Theses & Dissertations

The research in this dissertation developed statistical and linear system models to predict driving behavior according to driver attributes, vehicle characteristics, car-following dynamics and/or driving conditions. The scope of this research was limited to the interaction of two vehicles traveling in the same direction on interstate highways.

The statistical models proposed in this research investigated the contributions of the different vehicle types on the manner and likelihood of collision. Discrete choice models were used to estimate the probability of the types of collision (rear-end, angle and sideswipe) as functions of driver attributes, striking and struck vehicle types, pre-crash driving actions …

Antenna Designs For Wireless Medical Implants., Conor P. Conran

Masters

Active medical implants are devices that are surgically implanted inside the body. They have been developed to treat a wide range of ailments and many require some form of communications link with the outside world for maintenance and for remote medical diagnostics. Radio links promise a wide range of benefits over the traditional low frequency inductive coupling method.

Body tissue is a challenging environment, both for the device and for the radio signal that it transmits. Innovation in medical technology is creating a demand for high bandwidth links, and this in turn is driving the development of implantable antennas.

Many …

The Influence Of Light Beam Convergence On The Stop-Bands Of A One-Dimensional Photonic Crystal, Vladimir A. Tolmachev, Kevin Berwick, Tatiana S. Perova

Articles

The influence of beam convergence on the photonic band-gaps, or stop-bands (SBs), of onedimensional photonic crystals (1D PCs) is investigated. The investigation is based on an analysis of the gap map obtained from reflection spectra, calculated by the transfer matrix method for various angles of light incidence, φ, The calculated data is compared with reflection spectra taken using Fourier Transform Infrared microspectroscopy. It was found that the introduction of the parameter, Δφ to account for the focused light beam, for angles up to 20°, has little effect on the first, or lowest SB and the SBs adjacent to it. However, …

Reversible Photoluminescence Quenchin Of Cdse/Zns Quantum Dots Embedded In Porous Glass By Ammonia Vapor, A. O. Orlova, Yu A. Gromova, V. G. Maslov, O. V. Andreeva, A. V. Baranov, A. V. Federov, A. V. Prudnikau, M. V. Artemyev, Kevin Berwick

Articles

The photoluminescence response of semiconductor CdSe/ZnS quantum dots embedded in a borosilicate porous glass matrix to exposure to ammonia vapor is investigated. Formation of surface complexes on the quantum dots results in quenching of the photoluminescence and a shortening of the luminescence decay time. The process is reversible, desorption of ammonia molecules from the quantum dot surface causes the photoluminescence to recover. The sensitivity of the quantum dot luminescence intensity and decay time to the interaction time and the reversibility of the photoluminescence changes makes the CdSe/ZnS quantum dot in porous glass system a candidate for use as an optical …

Community Microgrid Based On Micro-Wind Generation System, Lubna Mariam, Malabika Basu, Michael Conlon

Conference papers

Penetration of renewable energy sources (such as solar/wind) are being explored mostly as micro power generation (μGen) or mega power plant system. In recent years, emphasis has been given on Microgrid (μGrid) systems because of their few advantages over μGen systems in terms of power quality, stability, reliability, economics etc. But the commercial installation of the μGrid system is not yet progressing significantly. This paper presents the techno-economic aspects of μGen and μGrid systems towards the development of grid connected community based μGrid (C-μGrid) system. Emphasis has been given to identify the benefits of the μGrid over the μGen system. …

A New Placement And Integration Method Of Upqc To Improve The Power Quality In Dg Network, Shafiuzzaman K. Khadem, Malabika Basu, Michael Conlon

Conference papers

A new proposal for the placement and integration of UPQC in DG connected microgrid/micro generation (μG) system has been presented here. DG converters (with storage), the load and shunt part of the UPQC will be placed at or after the PCC. The series part of the UPQC will be placed before the PCC and in series with the grid. DC link can be connected to the storage system also. Hence, it is termed UPQCμ_G. The advantages of the proposed UPQCμ_G over the normal UPQC are to compensate voltage interruptions in addition to voltage sags / swells, harmonic …

Economic Challenges And Optimisation Of Ocean Energy Electrical Systems, Fergus Sharkey

Books/Book chapters

No abstract provided.

Design And Analysis Of An Electronically Steerable Microstrip Patch And A Novel Coplanar Waveguide (Cpw) Fed Slot Antenna Array, Hamad Shaban Aldossary

Theses and Dissertations

Conformal Phased Array Antennas (CPAAs) are very attractive for their high gain, low profile, and beam scanning ability while being conformal to their mounting surface. Among them are microstrip patch phased arrays and wideband slot phased arrays which are of particular significance.

In this work, first the study, design, and implementation of a conformal microstrip patch phased array is presented which consists of a high gain beam scanning array implemented using microstrip delay lines controlled using GaAs SPDT switches. Then the study and design of a wideband Coplanar Waveguide (CPW)-fed slot phased array antenna is presented. In both cases the …

Modeling Of Sic Power Semiconductor Devices For Switching Converter Applications, Ruiyun Fu

Theses and Dissertations

Thanks to recent progress in SiC technology, SiC JFETs, MOSFETs and Schottky diodes are now commercially available from several manufactories such as Cree, GeneSiC and Infineon. SiC devices hold the promise of faster switching speed compared to Si devices, which can lead to superior converter performance, because the converter can operate at higher switching frequencies with acceptable switching losses, so that passive filter size is reduced. However, the ultimate achievable switching speed is determined not only by internal semiconductor device physics, but also by circuit parasitic elements. Therefore, in order to accurately predict switching losses and actual switching waveforms, including …

Polyspectral Signal Analysis Techniques For Condition Based Maintenance Of Helicopter Drive-Train System, Mohammed Ahmed Hassan Mohammed

Theses and Dissertations

For an efficient maintenance of a diverse fleet of air- and rotorcraft, effective condition based maintenance (CBM) must be established based on rotating components monitored vibration signals.

In this dissertation, we present theory and applications of polyspectral signal processing techniques for condition monitoring of critical components in the AH-64D helicopter tail rotor drive train system. Currently available vibration-monitoring tools are mostly built around auto- and cross-power spectral analysis which have limited performance in detecting frequency correlations higher than second order. Studying higher order correlations and their Fourier transforms, higher order spectra, provides more information about the vibration signals which helps …

Crystal Growth, Characterization And Fabrication Of Cdznte-Based Nuclear Detectors, Ramesh Madhu Krishna

Theses and Dissertations

In today's world, nuclear radiation is seeing more and more use by humanity as time goes on. Nuclear power plants are being built to supply humanity's energy needs, nuclear medical imaging is becoming more popular for diagnosing cancer and other diseases, and control of weapons-grade nuclear materials is becoming more and more important for national security. All of these needs require high-performance nuclear radiation detectors which can accurately measure the type and amount of radiation being used. However, most current radiation detection materials available commercially require extensive cooling, or simply do not function adequately for high-energy gamma-ray emitting nuclear materials …

High Resistivity Amorphous Selenium Alloy Semiconductors For Radiation Detection Applications, Abhinav Mehta

Theses and Dissertations

High resolution noninvasive tools of diagnosis has always derived and enabled scientific and medical research to probe and better understand subtleties of matter, intangible to the human eye. Radiation detection systems are highly dependent on advancements in materials and devices with front-end electronics. There are various discrete applications of these radiation detectors and each application imposes certain requirements so there is no single optimum radiation detector.

Flat panel x-ray imagers have gained high demand in the past decade because of exponential improvement in readout electronics. We have synthesized and investigated stabilized amorphous selenium (a-Se) alloys suitable for high resolution flat …

Effect Of Hafnium-Incorporation On The Microstructure And Dielectric Properties Of Cobalt Ferrite Ceramics, Stephen Josiah Wells

Open Access Theses & Dissertations

The effect of hafnium ion (Hf⁴⁺) incorporation in cobalt ferrite (CFO) was studied. Samples of Hf substituted CFO ceramic (CoFe_2-xHf_xO₄), were synthesized in the laboratory with hafnium concentrations ranging from x=0.000 to x=0.200. X-ray diffraction scans show that the Hafnium CFO crystalizes in the inverse spinel phase. Inclusion of hafnium causes lattice expansion, increasing the lattice parameter from 8.374 í? for pure CoFe2O4 to 8.391 í? for the highest concentration of hafnium tested (x=0.020). The dielectric properties of CFO are greatly enhanced by inclusion of hafnium. The enhancement is due to the …

Reduced-Order Modeling Using Orthogonal And Bi-Orthogonal Wavelet Transforms, Miguel Hernandez Iv

Open Access Theses & Dissertations

It is well known that model reduction methods borrow techniques typically found in data compression, and current state-of-the-art techniques for data compression are based on the wavelet transform. Given these facts, it is surprising that model reduction using wavelets has not received much attention and has not been adequately addressed in the literature. This research seeks to determine if wavelets can be used for model reduction and if wavelet model reduction is a viable alternative to existing model reduction methods.

In this work we propose a novel method for model reduction using wavelets. Specifically, we introduce techniques for deriving wavelet …

Dislocation Reduction In Silicon Doped High Aluminum Content Algan Layers For Deep Uv Optoelectronic Devices, Hung-Chi Chen

Theses and Dissertations

III-Nitride based deep ultraviolet (UV) light emitting diodes (LEDs) are prospective candidates to replace the conventional bulky, expensive and environmentally harmful mercury lamp as new UV light sources, used in the applications of water and air purification, germicidal and biomedical instrumentation systems, etc. Due to the lack of native substrates and poor carrier injection, AlGaN-based deep UV LED is suffering from low optical power and low overall efficiency, which prevents the availability of low cost, high efficiency deep UV LED on the market.

This dissertation is focused on improving the efficiency of deep UV LEDs, by improving the base template …