Electrical and Electronics Commons^™

High Frequency Dc-Dc Converter Design Optimization, Modeling And Control Based-Wbg Technology., Salah Ahmed Abdullah Eltief

Electronic Theses and Dissertations

The performance of DC-DC power converters is a cornerstone of modern electric vehicle (EV) powertrains, directly governing overall system efficiency, size, cost, and reliability. This dissertation presents a comprehensive performance analysis and optimization of DC-DC converter topologies to determine the most suitable design for high voltage EV applications. The evaluation rigorously compares efficiency, power losses, and physical size under a range of harsh operating conditions. A primary objective is to leverage Wide Bandgap (WBG) semiconductors, specifically Silicon Carbide (SiC), to push the performance boundaries of power conversion. While SiC devices are known for their superior material properties, a clear understanding …

Development Of An Embedded Iot Board For Real-Time Floor Estimation Of Autonomous Robots, Carter J. Sorensen

Electronic Theses and Dissertations

As service robots become more prevalent in multi-story environments such as hospitals, hotels, and laboratories, accurate floor-level detection is critical to ensuring operational reliability. Consider a robot tasked with delivering medical samples in a multi-story laboratory. Without accurate feedback, a robot exiting on the wrong floor could introduce delays, disrupt workflows, or compromise sample integrity. Internet of Things (IoT) technologies offer a way to address these risks by providing real-time error detection and corrective capability. However, current IoT-based floor estimation systems often require invasive modifications to building infrastructure—particularly elevator control panels. These approaches introduce challenges related to cost, liability, backward …

Development Of A Portable Electroencephalogram With Display, Seth D. Davis

Electronic Theses and Dissertations

In this experiment, the goal was to design, build, and test an Electroencephalogram (EEG) circuit that would then be paired with a touchscreen display as a portable unit for use in Schizophrenic research at East Tennessee State University at the Quillen College of Medicine. The requirements for this prototype denoted that the device had to be able to obtain a signal from two electrodes placed on the head of an individual with a third attached to the ankle as a ground, amplify and filter the signal, and display the results on a touchscreen display for recording and analyzing. The circuit …

Novel Sensors, Algorithms And Metrics For Human-Robot Interaction., Henry Lee Reynolds

Electronic Theses and Dissertations

The increased presence and deployment of robotics in sectors such as the medical field results in the demand for robots to, directly and indirectly, interface with people and their environment, making human-robot interaction (HRI) a vital thrust of robotics research. Assistive robots, for example, aid humans in accomplishing tasks or by providing support in the workforce. As the demand for nurses and the aging population increases, the assistive robots deployed will be deeply rooted in environments that require constant interaction with humans. This work contributed to improving aspects of HRI through 1) Expanding accessibility of the methods used for interfacing …

Deep Reinforcement Learning-Based Dynamic Routing And Spectrum Access In Aeronautical Networks., Zhe Wang

Electronic Theses and Dissertations

As the airspace is experiencing an increasing number of aircraft, spectrum sharing among Air Vehicles (AVs) and Terrestrial Users (TUs) emerges as a compelling solution to improve spectrum utilization efficiency. I investigated three types of aeronautical communication including the single-hop Air-Air Communication Network (AACN), the multi-hop Air-Air Ad-hoc Network (AAAN), and the Aerial and Terrestrial Hybrid Network (ATHN). I assume a spectrum-limited scenario through all communication networks. Thus, the number of communication pairs is greater than that of the available channels, resulting in co-channel interference due to the reuse of the same channel among communication links. In a single-hop AACN, …

A Modular Framework For Surface-Embedded Actuation And Optical Sensing In Soft Robots., Paul Bupe Jr

Electronic Theses and Dissertations

This dissertation explores the development and integration of modular technologies in soft robotics, with a focus on the OptiGap sensor system. OptiGap serves as a simple, flexible, cost-effective solution for real-time sensing of bending and deformation, validated through simulation and experimentation. Working as part of an emerging category of soft robotics called Soft, Curved, Reconfigurable, Anisotropic Mechanisms, or SCRAMs, this research also introduces the Thermally-Activated SCRAM Limb (TASL) technology, which employs shape-memory alloy (SMA) wire embedded in curved sheets for surface actuation and served as the initial inspiration for OptiGap. In addition, the EneGate system is presented as a complementary …

Investigating Mems Devices In Flow Conditions Relevant To Flow-Through Systems., Mohammad Shafquatul Islam

Electronic Theses and Dissertations

Advancements in microscale actuating technologies has substantially expanded the possibilities of interacting with the surrounding environment. Microstructures that deflect in response to mechanical forces are one of the largest application areas of microelectromechanical systems (MEMS). MEMS devices, functioning as sensors, actuators, and support structures, find applications in inertial sensors, pressure sensors, chemical sensors, and robotics, among others. Driven by the critical role of catalytic membrane reactors, this dissertation aims to evaluate enzyme activity on polymeric membranes and explore how fabrication methods from the field of Electrical and Computer Engineering (ECE) can incorporate sensing and actuation into these porous surfaces. Toward …

Design Of Hybrid Inverters Using Wideband Gap Semiconductors For Microgrid Application, Luca Gacy

Electronic Theses and Dissertations

As the world becomes more reliant on renewable energy sources such as solar and wind power, the need for high efficiency high power inverters connected to homes is more relevant than ever. Connecting these renewable energy sources (RES) coupled with an energy storage system (ESS) to the grid through a hybrid inverter, with the highest efficiency and grid stability, is quickly becoming a necessity for the near future. This thesis explores the integration of wide band gap semiconductors for the power stage in these systems, along with the analysis of hybrid inverter topologies and structures. The goal of this thesis …

The Study Of Corrosion On Additive-Manufactured Metals., Braydan Daniels

Electronic Theses and Dissertations

The purpose of this study was to investigate and compare the corrosion mechanisms between wrought and additive-manufactured (3D-printed) copper and stainless steel. The experimental procedure consisted of measuring the open circuit potential, electrochemical impedance spectroscopy, linear sweep voltammetry, Tafel analysis, surface topology, and scanning electron microscopy for each metal within salt water, tap water, sulfuric acid, and synthetic body fluid (excluding copper in synthetic body fluid).

Overall, printed stainless steel was more corrosion-resistant than wrought stainless steel in tap water and synthetic body fluid based on OCP, LSV, and surface topology results. Additionally, printed copper was more corrosion-resistant than wrought …

Unsupervised Learning Algorithm For Noise Suppression And Speech Enhancement Applications, Abdullah Zaini Alsheibi

Electronic Theses and Dissertations

Smart and intelligent devices are being integrated more and more into day-to-day life to perform a multitude of tasks. These tasks include, but are not limited to, job automation, smart utility management, etc., with the aim to improve quality of life and to make normal day-to-day chores as effortless as possible. These smart devices may or may not be connected to the internet to accomplish tasks. Additionally, human-machine interaction with such devices may be touch-screen based or based on voice commands. To understand and act upon received voice commands, these devices require to enhance and distinguish the (clean) speech signal …

Probing Signal-Based Data-Driven Modeling Of Power Electronics Smart Converter Dynamics Using Power Hardware-In-The-Loop, Nischal Guruwacharya

Electronic Theses and Dissertations

The main objective of this dissertation is to develop a generalized simulation and modeling framework for extracting dynamics of power electronic converters (PECs) with grid support functions (GSFs) and validate model accuracy through experimental comparison with physical measurements. The dynamic models obtained from this modeling framework aim to facilitate accurate dynamic analysis of a highly integrated power system comprising inverter-based resources (IBRs), specifically for stability assessment. These dynamic models helped in reducing simulation time and computational complexity, thereby enhancing efficiency. Moreover, it provides valuable insights for utilities and grid operators involved in effective system planning, operation, and dispatch. The dynamics …

Reduced Fuel Emissions Through Connected Vehicles And Truck Platooning, Paul D. Brummitt

Electronic Theses and Dissertations

Vehicle-to-infrastructure (V2I) and vehicle-to-vehicle (V2V) communication enable the sharing, in real time, of vehicular locations and speeds with other vehicles, traffic signals, and traffic control centers. This shared information can help traffic to better traverse intersections, road segments, and congested neighborhoods, thereby reducing travel times, increasing driver safety, generating data for traffic planning, and reducing vehicular pollution. This study, which focuses on vehicular pollution, used an analysis of data from NREL, BTS, and the EPA to determine that the widespread use of V2V-based truck platooning—the convoying of trucks in close proximity to one another so as to reduce air drag …

Automatic Testing Of Organic Strain Gauge Tactile Sensors., Brian P. Goulet

Electronic Theses and Dissertations

Human-Robot Interaction is a developing field of science, that is posed to augment everything we do in life. Skin sensors that can detect touch, temperature, distance, and other physical interaction parameters at the human-robot interface are very important to enhancing the collaboration between humans and machines. As such, these sensors must be efficiently tested and characterized to give accurate feedback from the sensor to the robot. The objective of this work is to create a diversified software testing suite that removes as much human intervention as possible. The tests and methodology discussed here provide multiple realistic scenarios that the sensors …

Additive Manufacturing Using Robotic Manipulators, Fdm, And Aerosol Jet Printers., Alexander Curry

Electronic Theses and Dissertations

Additive manufacturing has created countless new opportunities for fabrication of devices in the past few years. Advances in additive manufacturing continue to change the way that many devices are fabricated by simplifying processes and often lowering cost. Fused deposition modeling (FDM) is the most common form of 3D printing. It is a well-developed process that can print various plastic materials into three-dimensional structures. This technology is used in a lot of industries for rapid prototyping and sometimes small batch manufacturing. It is very inexpensive, and a prototype can be created in a few hours, rather than days. This is useful …

Collaborative Human-Machine Interfaces For Mobile Manipulators., Shamsudeen Olawale Abubakar

Electronic Theses and Dissertations

The use of mobile manipulators in service industries as both agents in physical Human Robot Interaction (pHRI) and for social interactions has been on the increase in recent times due to necessities like compensating for workforce shortages and enabling safer and more efficient operations amongst other reasons. Collaborative robots, or co-bots, are robots that are developed for use with human interaction through direct contact or close proximity in a shared space with the human users. The work presented in this dissertation focuses on the design, implementation and analysis of components for the next-generation collaborative human machine interfaces (CHMI) needed for …

Distributed Control, Optimization, And State Estimation For Renewable Power System, Qiao Li

Electronic Theses and Dissertations

The traditional power systems are usually centralized systems, in which the control, operation and monitoring are performed by the centralized control center, e.g., SCADA. However, with the development of renewable energy, power systems are getting more and more distributed. So, it becomes necessary to establish the distributed power system operation methods for these power systems. In this research, the distributed techniques for the renewable power systems are proposed based on the consensus protocol technique from graph theory. These techniques cover the three important problems in power systems, i.e., economic dispatch, state estimation, and optimal power flow. First, the Distributed Economic …

Design, Manufacture, And Test Of A Hybrid Aerial-Ground Robotic Platform, William Garrett Willmon

Electronic Theses and Dissertations

A hybrid aerial-ground robotic platform allows for enhanced functionality combining most of the operational profiles of an aerial and ground vehicle with applications to intelligence, surveillance, reconnaissance (ISR), infrastructure inspection, emergency response, photography, etc. Motivated by this challenge, we designed, developed, and tested a prototype hybrid aerial-ground robotic vehicle capable of guidance, navigation, and control in the air and on the ground. The thesis focus is on the system design. As such, at first, we designed and analyzed the mechanical component to ensure durability. We then designed the electrical component to reduce overall weight and maximize battery life. We developed …

Enhanced Charge Carrier Dynamics And Defects Passivation In Hybrid Perovskite Solar Cell Using A Novel Organic Halide Salt, Md Ashuqur Rahman Laskar

Electronic Theses and Dissertations

In the last few years, active research works on hybrid perovskite solar cells (HPSCs) have been going on throughout the world as a part of clean energy revolution. HPSCs have already proved their potentiality as future solar technology through their promising photovoltaic performances and ability for low temperature based solution processing. Nevertheless, still there are remaining challenges of better charge carrier dynamics and defects minimization in HPSCs. Overcoming these challenges are very important to achieve high power conversion efficiency (PCE) practically. Aiming this, a novel organic halide salt called Phenylhydrazinium Iodide (PHAI) is introduced as additive with CH₃NH …

Solarpede: An Untethered Micro Robot Powered By Light., Jordan Fredrick Klotz

Electronic Theses and Dissertations

Micro-Robotics looks to implement robotics principles at a small scale and has gained popularity in recent decades as a gateway to new research areas such as micro-factory applications. The SolarPede is a second-generation, cm-scale micro-crawler designed for such micro factory applications which is equipped with a legged locomotion system and an electronic backpack. The SolarPede is an evolution of its predecessors and features power and signal conditioning capabilities, gait pattern generation, and Bluetooth connectivity. The components which make up SolarPede have been full validated and tested, and its systems have been realized in the form of a body made from …

Control Strategy For A Small-Scale Microgrid Based On Battery Energy Storage System-Virtual Synchronous Generator (Bess-Vsg), Wei Gao

Electronic Theses and Dissertations

As one of widely deployed renewable energy resources, PV power is playing a very important role in microgrids today. It has advantages such as making the best of natural solar energy and being friendly to our environment. In this thesis, solar PV based microgrid is studied using modeling and simulation. Microgrid can run in either grid-connected-mode or islanded-mode. However, there are also some disadvantages for solar power. For solar panel, its output is influenced by weather conditions such as illumination intensity and temperature. In addition, during the control process of grid-connected mode, it is hard to guarantee its output power …

A Study On Distributed Generation With A Focus On Solar Power, Shravan Kumar Tomar

Electronic Theses and Dissertations

Centralized generation is when electric power is produced in a large scale of tens of MWs and is located away from the end user. This kind of production is connected to a series of high-voltage transmission lines. Electricity is then delivered to the end user through a network of distribution grids. Centralized generation tend to have multiple end user with multiple user profiles.

Distributed Generation is when is produced in a small scale and is located at the site of or very close to the end user. There are many ways distributed generation can be achieved, Solar power being the …

Semiconductor Device Modeling, Simulation, And Failure Prediction For Electrostatic Discharge Conditions, Hang Li

Electronic Theses and Dissertations

Electrostatic Discharge (ESD) caused failures are major reliability issues in IC industry. Device modeling for ESD conditions is necessary to evaluate ESD robustness in simulation. Although SPICE model is accurate and efficient for circuit simulations in most cases, devices under ESD conditions operate in abnormal status. SPICE model cannot cover the device operating region beyond normal operation. Thermal failure is one of the main reasons to cause device failure under ESD conditions. A compact model is developed to predict thermal failure with circuit simulators. Instead of considering the detailed failure mechanisms, a failure temperature is introduced to indicate device failure. …

Analysis, Design And Efficiency Optimization Of Power Converters For Renewable Energy Applications, Xi Chen

Electronic Theses and Dissertations

DC-DC power converters are widely used in renewable energy-based power generation systems due to the constant demand of high-power density and high-power conversion efficiency. DC-DC converters can be classified into non-isolated and isolated topologies. For non-isolated topologies, they are typically derived from buck, boost, buck-boost or forth order (such as Cuk, Sepic and Zeta) converters and they usually have relatively higher conversion efficiency than isolated topologies. However, with the applications where the isolation is required, either these topologies should be modified, or alternative topologies are needed. Among various isolated DC-DC converters, the LLC resonant converter is an attractive selection due …

Programmable Low Loss Orthogonal Frequency Coded Surface Acoustic Wave Correlator Filters, Marshall Smith

Electronic Theses and Dissertations

Simultaneous Transmit and Receive (STAR) communication is being developed as a means of improving spectral efficiency in wireless communication systems. If the obstacle of self-interference can be sufficiently overcome, it is possible to double the spectral efficiency of an equivalent time or frequency division duplexed system. Spread spectrum techniques can reduce self-interference by using orthogonal or pseudo-orthogonal codes to encode the transmit signal and decode the receive signal. Hardware correlator filters are developed for use with STAR radio systems using orthogonal frequency coded (OFC) surface acoustic wave (SAW) devices. OFC is a type of spread spectrum communication that can be …

Reconfigurable Reflectarray Antennas With Bandwidth Enhancement For High Gain, Beam-Steering Applications, Michael Trampler

Electronic Theses and Dissertations

Reconfigurable reflectarrays are a class of antennas that combine the advantages of traditional parabolic antennas and phased array antennas. Chapter 1 discusses the basic operational theory of reflectarrays and their design. A review of previous research and the current status is also presented. Furthermore the inherent advantages and disadvantages of the reflectarray topography are presented. In chapter 2, a BST-integrated reflectarray operating at Ka band is presented. Due to the monolithic integration of the tuning element, this design is then extended to V band where a novel interdigital gap configuration is utilized. Finally to overcome loss and phase limitations of …

Sparse Signal Recovery Under Sensing And Physical Hardware Constraints, Davood Mardaninajafabadi

Electronic Theses and Dissertations

This dissertation focuses on information recovery under two general types of sensing constraints and hardware limitations that arise in practical data acquisition systems. We study the effects of these practical limitations in the context of signal recovery problems from interferometric measurements such as for optical mode analysis. The first constraint stems from the limited number of degrees of freedom of an information gathering system, which gives rise to highly constrained sensing structures. In contrast to prior work on compressive signal recovery which relies for the most part on introducing additional hardware components to emulate randomization, we establish performance guarantees for …

Frequency-Reconfigurable Microstrip Patch And Cavity-Backed Slot Espars, Wei Ouyang

Electronic Theses and Dissertations

Wireless communication systems have rapidly evolved over the past decade which has led to an explosion of mobile data traffic. Since more and more wireless devices and sensors are being connected, the transition from the current 4G/LTE mobile network to 5G is expected to happen within the next decade. In order to improve signal-to-noise ratio (SNR), system capacity, and link budget, beam steerable antenna arrays are desirable due to their advantage in spatial selectivity and high directivity. Electronically steerable parasitic array radiator (ESPAR) that can achieve low-cost continuously beamsteering using varactor diodes have attracted a lot of attention. This dissertation …

Hybrid Perovskite Characterization And Device Applications., Kasun Fernando

Electronic Theses and Dissertations

Hybrid perovskites are a group of materials that has shown a great impact in the field of scientific research in the past decade due to the efficiency gain within a short period of time. Hot casting is one technique that has been producing high efficient and stable solar cells. Electrical transportation of lateral device structure by such film is explored to understand basic properties and predict possible device applications using it. Under dark, memristive ability of the film was explored using various experiments. Unique uni-polar memristor ability was observed. Using the experimental results, a model is hypothesized using the concepts …

High Dynamic Range Optical Devices And Applications., Elijah Robert Jensen

Electronic Theses and Dissertations

Much of what we know about fundamental physical law and the universe derives from observations and measurements using optical methods. The passive use of the electromagnetic spectrum can be the best way of studying physical phenomenon in general with minimal disturbance of the system in the process. While for many applications ambient visible light is sufficient, light outside of the visible range may convey more information. The signals of interest are also often a small fraction of the background, and their changes occur on time scales so quickly that they are visually imperceptible. This thesis reports techniques and technologies developed …

Challenges In Flexible Microsystem Manufacturing : Fabrication, Robotic Assembly, Control, And Packaging., Danming Wei

Electronic Theses and Dissertations

Microsystems have been investigated with renewed interest for the last three decades because of the emerging development of microelectromechanical system (MEMS) technology and the advancement of nanotechnology. The applications of microrobots and distributed sensors have the potential to revolutionize micro and nano manufacturing and have other important health applications for drug delivery and minimal invasive surgery. A class of microrobots studied in this thesis, such as the Solid Articulated Four Axis Microrobot (sAFAM) are driven by MEMS actuators, transmissions, and end-effectors realized by 3-Dimensional MEMS assembly. Another class of microrobots studied here, like those competing in the annual IEEE Mobile …