Electrical and Electronics Commons^™

Development Of Dynamic Proof-Mass Configurations For Broadband Piezoelectric Energy Harvesting, Nico E. Galarza

Electrical and Computer Engineering ETDs

The purpose of this thesis is to investigate and develop dynamic proof-mass configurations for broadband piezoelectric energy harvesting. Conventional piezoelectric energy harvesters are typically limited by narrow operating bandwidths, restricting their performance under variable-frequency excitation. This research presents the design, fabrication, and experimental evaluation of multiple proof-mass concepts intended to increase the usable frequency range of cantilever-based piezoelectric energy harvesters. Several dynamic mass configurations were developed using additive manufacturing techniques and integrated with commercially available piezoelectric cantilevers. Experimental testing was conducted under controlled vibration conditions to characterize voltage response, resonant behavior, and bandwidth performance. The results demonstrate that dynamic proof-masses …

Load Flow And Fault Performance Evaluation Of Interconnected Minigrids In Uganda Using Digsilent Powerfactory, Prossy Mutesi, Santos Kihwele, Emmanuel Matee

Tanzania Journal of Engineering and Technology (TJET)

The increasing demand for decentralized, reliable electricity in rural Sub-Saharan Africa has catalyzed the deployment of minigrids as an intermediate electrification strategy. This study investigates two solar photovoltaic (PV) mini-grids: Kyamugarura and Kanyegaramire, located in western Uganda, approximately 3km apart. Each mini grid initially consisted of 13 kW installed photovoltaic (PV) capacity, supplying power to households and small businesses. Due to rising demand and regular evening blackouts, both mini-grids are being upgraded to 57 kWp each. The integration of these upgraded systems into the national utility grid is proposed and simulated to evaluate performance improvements under two medium-voltage interconnection options: …

Hybrid Solar - Coal Thermal Energy System For Industrial Process Heat At Sayona Drinks Limited In Tanzania, Santos Kihwele, Elisha D. Bitesigirwe

Tanzania Journal of Engineering and Technology (TJET)

Over the past two decades, global efforts to mitigate pollution from conventional energy sources have intensified, with coal remaining a major contributor to carbon emissions. While fossil fuels cannot be eliminated from thermal generation in manufacturing industries, particularly in middle‑income countries such as Tanzania, they continue to dominate as the primary energy source. Industries including food and beverage, paper, textile, paints, chemicals, and pharmaceuticals require substantial thermal energy for heating and drying, and typically rely on coal and natural gas.This study introduces a unique application of a parabolic trough solar thermal system with integrated thermal energy storage, specifically tailored to …

Me3329 Modular Phonograph Gearbox, Garrett Andrik Leighton, Preston Robert Hupe, Gavin Carter Ebner, Andrew Renato Reyes

Mechanical Engineering

The Mechanical Engineering Department at California Polytechnic State University, San Luis Obispo (Cal Poly), seeks to develop a laboratory tool allowing students to reinforce concepts of gears for Mechanical Systems Design (ME329). Some current laboratories do not provide students with hands-on interaction, and the department lacks equipment and documentation to support a standardized lab. With ME329 expanding from ten to fifteen weeks, there is an opportunity to create a physical gearbox design lab allowing students to reinforce lecture material in engaging ways, while standardizing student learning. This senior project is presented and sponsored by Professor Alan Zhang. It will be …

Custom Animatronic Puppet, Jake Schuman, Fredy Herrarte, Madison Reedy, Jackson Reynolds

Mechanical Engineering

This project involved the design, fabrication, and implementation of a custom audio-animatronic puppet modeled after Dr. Brian Davis for the California Polytechnic State University Mechanical Engineering Department. The objective was to create an expressive, lifelike character capable of synchronized speech, head movement, arm gestures, and seated-to-standing motion while demonstrating the integration of mechanical design, controls, manufacturing, and artistic fabrication.

The final system consists of an 18-degree-of-freedom animatronic platform utilizing servo-driven facial and upper-body actuation combined with a pneumatic standing mechanism. A modular aluminum and 3D-printed structural framework was developed using SolidWorks and validated through engineering analysis. Character shells were digitally …

Mass - Modular Acoustic Suppression System, Julia Megargle, Michael A. Milner, Lucas Kaemmererer, Jonathan Corvera, Gabriel Choi, Emmi Cayer

Mechanical Engineering

The Modular Acoustic Suppression System (MASS) is a mass tuned damper that reverberates a membrane atop a cavity to absorb select acoustic frequencies produced by the Environmental Control and Life Support Systems (ECLSS) within NASA's Artemis Human Lander. The height of the reverberation chamber is adjusted to mitigate a range of varying tonal frequencies within the human lander.

Autonomous Vision-Based Litter Collection Rover, Dante Michael Benedetti, Benjamin Scott Tavares, Nathan Heil

Electrical Engineering

This report documents the design, implementation, and testing of an autonomous litter-collection rover developed as a Senior Project Design Lab (EE 460/463/464) at California Polytechnic State University. The rover integrates autonomy, computer vision, embedded real-time control, mecanum-wheel omnidirectional mobility, and a two-degree-of-freedom robotic arm to detect, approach, and collect small ground-level litter such as bottles, wrappers, and paper fragments.

The system uses a two-layer compute architecture: an NVIDIA Jetson Orin Nano running ROS 2 for perception, SLAM, and path planning, paired with an STM32L4A6ZG microcontroller for real-time motor control and odometry. The robot is built on a multi-level aluminum frame …

The Pid-Based Three Quadcopter Uavs Formation Control Under External Disturbance, Vo Van An, Trinh Luong Mien

Makara Journal of Technology

This paper presents the design and evaluation of a formation control strategy for three quadcopter UAVs, based on a PID controller in a leader–follower structure, under the influence of external disturbances. Each UAV employs a six-degree of-freedom dynamic model and utilises a cascade PID control architecture, in which the inner control loop stabilises the attitude. In contrast, the outer control loop regulates position and maintains the formation. The PID parameters are tuned using the Ziegler–Nichols method to ensure simple implementation and low computational cost. The performance of the control system is evaluated through simulations in the MATLAB environment for two …

Implantable, Sensor-Embedded Vascular Graft Towards Wireless Monitoring Of Stenosis, Nnamdi Dike

LSU Master's Theses

Arteriovenous (AV) grafts are commonly used to provide vascular access for hemodialysis in patients with end-stage renal disease. Despite their widespread use, AV grafts are prone to complications such as stenosis and thrombosis. Early detection of these conditions remains challenging with current monitoring methods too costly or insufficient. This work presents the design, fabrication, and validation of an LC pressure sensor embedded within a model AV graft to enable real-time monitoring. The proposed system integrates a parallel-plate capacitive pressure sensor with a spiral inductor to form an LC circuit embedded within an elastomeric graft wall. The Ecoflex 00-30 dielectric layer …

Tuning And Performance Of Pid Controlled Low Complexity Systems, Timothy Evans

Honors Theses

Proportional integral derivative (PID) controllers are used for precise position and orientation control in systems such as autonomous underwater vehicles (AUVs). This project supports the University of Southern Mississippi’s (USM) Robotics Club’s RoboSub AUV effort by developing, troubleshooting, and manually tuning PID controllers to characterize tracking performance and settling time across systems of increasing complexity. Initially, the project hypothesized that tracking performance would be reduced and settling times would increase as system complexity advanced from one degree-of-freedom (DOF) to two DOF. However, prior research was found that suggests that for small disturbances around an equilibrium state, separate PID-controlled DOFs can …

Portable Ice Cube Maker, Ayden Ziegler, Emiliano Hansen, Wyatt Engdahl, Dane Hansen

Mechanical Engineering

This Final Design Report outlines the senior design project undertaken by a team of mechanical engineering students at California Polytechnic State University, San Luis Obispo, for the development of a portable backpacking ice cube maker. The project aims to design, build, and test a lightweight, compact device that produces ice cubes for backpackers in remote outdoor environments. The goal is to create a functional prototype that is durable, user-friendly, and suitable for backcountry use. This document details background research, project objectives, and project plan, and current design status.

Automation And Habitat Development For A Space Based Marine Life Environment, Logan Trimmer, Alexander Hang

Harrisburg University Other Works

This project was a cross-collaboration between the Environmental Sciences and Advanced Manufacturing and Robotics programs for the company Monolith Space.

The goal of this project was to design an autonomous system to be able to track qualities of water in an aquaculture system designed to be sent to space.

Multi-Objective Optimization Strategy For Component Sizing In Solar-Hydrogen Microgrids Using An Advanced Hybrid Genetic Algorithm, Dylan Jones

UNF Graduate Theses and Dissertations

This thesis presents the development of a genetic algorithm (GA) optimization framework for the design and component sizing of hybrid solar-hydrogen microgrids. The framework addresses a critical gap in research and existing commercial tools by unifying performance maximization and cost minimization objectives across both grid-tied and islanded configurations. Integrating solar photovoltaics, electrolyzers, hydrogen storage, fuel cells, and batteries, the GA employs adaptive weighting and dynamic boundary constraints to balance technical feasibility with economic efficiency. To ensure real-world viability, the algorithm relies on a novel Daylight Sun Factor (DSF) for localized solar assessment and was rigorously validated against multi-year, high-fidelity irradiance …

Wind Tunnel Instrumentation And Testing, Nicholas Marek, Abraham Mezera, Laura Jin, Hayden Smith, Curtis Cook

Student Scholar Symposium

The Raymond B. Jones College of Engineering was contacted by an automotive engineering firm seeking to use the college’s wind tunnel for gathering data on the aerodynamic performance of a proprietary prototype automotive door. Specifically, the client requested the quantification of the drag coefficient of the model at extreme wind speeds. The drag coefficient, a dimensionless number that quantifies the resistance of a specific geometric shape to airflow, will be a valuable datapoint for the client’s design iteration. Due to the sensitive nature of their work, the client has wished to remain anonymous. RBJCOE professors tasked a senior design team …

Investigating The Harmonic Content Of A Pwm Inverter With Varying Modulation Index, Peter Makolo

Tanzania Journal of Engineering and Technology (TJET)

Photovoltaic energy is a clean and endless vital renewable energy. In order to generate electricity from solar energy an inverter is required to transform the direct current into alternating current. Also, with the emerging of new ultra-high voltage direct current transmission technology, the rectification and inverters play a great role. Most three-phase two-level inverters draw harmonics that cause heat dissipation, waveform distortions hence affect the electrical loads. Knowing that Total Harmonic Distortion content of voltage source inverter is important and must be within the allowable range. Several schemes are suggested to mitigate the distortion in order to produce as much …

Thermal Energy Storage System Using Silica Sand As Heat Storage Medium: Simulation Of Geita Gold Mine, Santos Kihwele

Tanzania Journal of Engineering and Technology (TJET)

Currently, Geita Gold Mine (GGM) relies on electrical energy from the national grid and diesel power generators to generate electricity for various industrial applications. The plant currently spends a large amount of money on generating power from diesel generators. The total annual cost of power generation from diesel generators including lubricants is USD 56,057,990. The total annual fuel cost is USD 53,531,805 for a total of 54,985,473 liters per year. Most of the power generated by the generators is consumed in the industrial thermal processes. Thermal energy applications at the plant are thermal drying of the extracted ores to remove …

A Review Of Lithium-Ion Battery Capacity Fade Deceleration At Power Fluctuations In Renewable Energy Systems, Isaac Gwayi

Tanzania Journal of Engineering and Technology (TJET)

Application of lithium-ion (Li-ion) batteries to store energy in renewable energy systems (RESs) is increasing due to their promising properties. Therefore, it is crucial to understand aging behaviours of Li-ion battery during RES life time as this directly affects cost of energy. Li-ion battery aging can be categorised into calendar aging and cycle aging. Calendar aging depends mainly on temperature and state of charge (SoC). In addition to temperature and SoC, cycle aging depends also on charge and discharge current rates and cut-off voltages. Higher current rates lead to faster Li-ion battery aging. It is necessary to identify appropriate battery …

Optimal Placement Of Distributed Generation Units In Power Distribution Networks Using Particle Swarm Optimization, Owdean M. Suwi

Tanzania Journal of Engineering and Technology (TJET)

Power losses and voltage drops in distribution networks are critical issues in power system operation, reducing efficiency, reliability, and overall quality of the power supply to customers. Additionally, the rising electricity demand, deregulation of energy markets, and congestion in transmission networks have further contributed to the declining performance of the grid. To address these challenges, integrating distributed generation units (DGUs) into electric distribution systems has gained significant attention. Furthermore, the integration of DGUs into conventional fossil fuel-based power plants is becoming necessary to reduce greenhouse gas emissions. However, proper placement and sizing of DGUs are crucial for achieving optimal benefits. …

The Impacts Of Renewable Energy Sources: A Review On Grid Inertia And Frequency Regulation, Sospeter Gabriel

Tanzania Journal of Engineering and Technology (TJET)

The power system is gradually transitioning into low inertia due to integrating substantial intermittency quantity of converter-based renewable energy sources, such as wind and photovoltaic power, into the current power grid network. This integration presents significant inertia and frequency control challenges to the network as a result of a decrease in the percentage of synchronous generators. Moreover, faster frequency deviations are posed by the mismatch between the supply and demand during contingencies, which creates difficulties in preserving the frequency stability of the power system. This research explores the impacts of renewable energy sources (RESs) on grid inertia and frequency management …

Calibration Of Measurement Tools In The Experimental Test Rig For Hydropower Performance Evaluation, Ombeni J. Mdee

Tanzania Journal of Engineering and Technology (TJET)

The demonstration of a typical hydropower plant requires the development of a test rig with the installation of tools to measure the performance parameters. The measurement tools require a calibration process to improve the quality of recorded data. This study involved the calibration of traditional and automated measurement tools connected to the hydropower test rig through an Arduino microprocessor. The automated measurement tools included a pressure transducer, flow meter, digital tachometer, and torque transducer, while traditional measurement tools, including a pressure gauge, concrete water tank, contact tachometer, and force lever arm balance, were connected in the same test rig during …

How’S It Growing? Tools For Observing Snow And Sea Ice In A Changing Arctic Ocean, Ian Alexander Raphael

Dartmouth College Ph.D Dissertations

September Arctic sea ice extent has diminished by roughly 50% in the 45 years since satellite observations began. The Arctic Ocean may experience ice-free summers within the next decade, with implications for habitat, resource extraction, geopolitics, and local and global climate change. To predict how Arctic sea ice will change in the future, we need to understand its behavior in the present. In situ sea ice mass balance measurements (snow accumulation, ice growth, snow and ice surface melt, and bottom melt) are essential for studying the processes driving rapid changes in the ice pack, and for validating remote sensing measurements …

Development Of An Embedded Iot Board For Real-Time Floor Estimation Of Autonomous Robots, Carter J. Sorensen

Electronic Theses and Dissertations

As service robots become more prevalent in multi-story environments such as hospitals, hotels, and laboratories, accurate floor-level detection is critical to ensuring operational reliability. Consider a robot tasked with delivering medical samples in a multi-story laboratory. Without accurate feedback, a robot exiting on the wrong floor could introduce delays, disrupt workflows, or compromise sample integrity. Internet of Things (IoT) technologies offer a way to address these risks by providing real-time error detection and corrective capability. However, current IoT-based floor estimation systems often require invasive modifications to building infrastructure—particularly elevator control panels. These approaches introduce challenges related to cost, liability, backward …

Pressure Switch Tester, Michael Starasinich, Andrew Dobson, Jordan Huschen, Mitchell Smith, Melvin Brown Iii

Honors Capstones

Abstract—- The Pressure Switch Test Stand is a comprehensive and automated testing solution designed to streamline the actuation and validation of simultaneously. At the core of the system is a PLC-controlled architecture that enables precise control and simulation of pressure conditions, replicating real-world scenarios to ensure accurate and reliable switch performance.

This test stand integrates robust mechanical fixtures, a reliable pneumatic control system, custom-designed electrical circuits, and a modular software interface, working in unison to deliver consistent and high-fidelity testing outcomes. Each pressure switch undergoes a sequence of pressure ramps and holds, with the system continuously monitoring switch states, activation …

Development Of A Cost-Effective Daq For Measuring Brake Performance In Race Cars, Adrin Alias

2025 Spring Honors Capstone Projects - Archive

This project explores the feasibility of creating a cost-effective data acquisition (DAQ) system for high-speed, real-time brake performance testing of Formula SAE racecars. The research addresses the limitations of the current MoTeC DAQ system currently employed by the team, which is costly and time-consuming to set up for on-car testing. The team will use a brake dynamometer for steady-state comparisons of different brake pad compounds (senior design project), but evaluating real-world performance requires on-car testing. By systematically comparing various hardware platforms, sensors, communication protocols, and storage solutions, this project aims to balance cost-efficiency with reliability and performance. The research evaluates …

Finding Groundwater With Electricity: Research And Testing Of An Electro-Resistive Ground-Surveying Device For Use In Well-Drilling Applications, Samuel L. Heath

Senior Honors Theses

A custom-built electro-resistive water detection device is tested under various conditions to evaluate its overall performance and sensitivity to changing variables. The tests, designed to assess accuracy and precision, revealed that the prototype exhibits high reliability (~ 99%) for both Schlumberger and Wenner arrays across different electrode spacings and soil conditions. Moreover, the measured resistivity values from the soil tests aligned with established literature ranges for each soil type. The device also showed the ability to consistently detect changes in soil water content by producing measurable variations in resistivity. At a total cost of $181, this prototype can serve as …

Validating An Electronics Cooler Experiment And Optimizing Its Performance Using Ansys Icepak, Daniel V. Curl

Mechanical Engineering Undergraduate Honors Theses

Researchers at the University of Arkansas' Mechanical and Electrical Engineering Research Departments have designed and built a cold plate and substrate design for a 10 kV SiC MOSFET power module. Many variables define the design of the cold plate and substrate system and have quantifiable effects on the device’s performance. These variables include but are not limited to geometry and material selection of the fins and substrate. Manufacturing many test designs, running experiments, and comparing their performance is a time-consuming and expensive design optimization method that may be effective for some low-cost applications. Still, simulation is often a more cost-effective …

Synthetic Inertia Provision For Load Frequency Control In Networks With High Penetration Of Renewable Energy Sources, Paulina Mkoi

Tanzania Journal of Engineering and Technology (TJET)

The integration of renewable energy sources (RESs) such as solar photovoltaic (PV) and wind energy has become a promising solution as the world shifts toward clean energy. Solar PV and wind resources are increasingly replacing conventional synchronous generators, leading to reduced system inertia and increased vulnerability to frequency instability during disturbances. To address this challenge, this study proposes a novel synthetic inertia provision strategy using a battery energy storage system (BESS) integrated alongside solar PV. The proposed method dynamically compensates for the loss of inertia by considering the variability of solar PV output due to changes in irradiance and temperature. …

Clustering Mini-Grids To Enhance Power Systems Reliability In Distributed Generation, Santos Kihwele

Tanzania Journal of Engineering and Technology (TJET)

This study investigates the effectiveness of clustering mini-grids as a method to improve the reliability and operational stability of distributed generation systems in remote areas, particularly where renewable energy sources are predominant. As renewable resources like solar and wind are increasingly integrated into mini-grids, these systems face various challenges, particularly in maintaining stable voltage and frequency across interconnected networks. Such issues are compounded by the intermittent nature of renewable energy sources and the lack of extensive communication infrastructure in rural or resource-constrained settings. To address these control challenges, this study applies droop control techniques to two mini-grids in Uganda, utilizing …

Semi-Autonomous Trash Bot, Ben Leon, Ethan Mashburn, Connor Olivera, Dillon Michael Wood

ATU Scholars Symposium

Title: Semi-Autonomous Trash Robot

Authors: Benjamin Leon, Ethan Mashburn, Connor Olivera, Dillon Wood

Abstract: Environmental pollution is becoming more worrying every day as megatons of human waste persist in vast amounts in our ecosystems. The existing waste collection methodologies, with the labor, time, and cost components combined, make the process cumbersome. A potential solution could be an automated waste collection robot that incorporates AI into a cheap system that autonomously detects trash. This report proposes a machine that may be manufactured to adequate standards in terms of size and cost and deployed in various environments, with the ultimate goal of …

Design And Development Of A Low-Cost Educational Robot: A Scalable And Affordable Software Learning Platform, Diana Refaat Henry Jacob, Mohamed Tarek Elawa, Ashraf Mohamed Hafez

Journal of Engineering Research

This study presents the design and development of a low-cost educational robot to enhance learning experiences in robotics and programming. The system integrates robust software development, ensuring seamless interaction between sensors, actuators, and a custom-designed graphical user interface (GUI). The robot is equipped with various sensors and actuators to support a broad range of experiments and educational applications. The software architecture is detailed, focusing on its modularity and ease of use, enabling students to intuitively program and interact with the robot. Additionally, a series of experiments were conducted to evaluate the performance of the sensors and actuators, providing insights into …