Electrical and Electronics Commons^™

System Integration And Validation Of The Cal Poly Spacecraft Attitude Dynamics Simulator Mk. Iv, Bricen S. Rigby

Master's Theses

The Cal Poly Spacecraft Attitude Dynamics Simulator (SADS) is an ongoing project that seeks to enable the simulation and validation of sensors, actuators, and control logic related to spacecraft attitude control. The SADS platform rests atop a spher- ical air-bearing device which allows for nearly frictionless rotation in all three axes. The orientation of the platform is controlled by four reaction wheels arranged in a pyramidal configuration. Over the past few years, there have been significant updates to the reaction wheel subsystem, as well as requests for a more capable central com- puter. Therefore, a new system architecture for the …

Load Flow And Fault Performance Evaluation Of Interconnected Minigrids In Uganda Using Digsilent Powerfactory, Prossy Mutesi, Santos Kihwele, Emmanuel Matee

Tanzania Journal of Engineering and Technology (TJET)

The increasing demand for decentralized, reliable electricity in rural Sub-Saharan Africa has catalyzed the deployment of minigrids as an intermediate electrification strategy. This study investigates two solar photovoltaic (PV) mini-grids: Kyamugarura and Kanyegaramire, located in western Uganda, approximately 3km apart. Each mini grid initially consisted of 13 kW installed photovoltaic (PV) capacity, supplying power to households and small businesses. Due to rising demand and regular evening blackouts, both mini-grids are being upgraded to 57 kWp each. The integration of these upgraded systems into the national utility grid is proposed and simulated to evaluate performance improvements under two medium-voltage interconnection options: …

Analysis And Design Of A 2-Bit Millimeter-Wave Reconfigurable Intelligent Surface And Investigation Of Fss-Assisted Angular Stability, Max Spalek

Master's Theses

Millimeter-Wave (mm-wave) technology utilizes high frequency spectrum and can deliver multi-gigabit speeds, ultra-low latency, and massive bandwidth capacity. However, this technology is rather new and many technical challenges remain. On the other hand, Reconfigurable Intelligent Surfaces (RIS) have emerged as promising structures for controllable electromagnetic wavefront manipulation in wireless communication systems. This thesis presents the design of a 2-bit RIS unit-cell element operating throughout the 30–34 GHz mm-wave band, where the structure was progressively refined from an initial resonating geometry toward a grounded reflective RIS configuration. The proposed structure utilizes PIN-diode switching states to produce four discrete reflected phase states …

Custom Animatronic Puppet, Jake Schuman, Fredy Herrarte, Madison Reedy, Jackson Reynolds

Mechanical Engineering

This project involved the design, fabrication, and implementation of a custom audio-animatronic puppet modeled after Dr. Brian Davis for the California Polytechnic State University Mechanical Engineering Department. The objective was to create an expressive, lifelike character capable of synchronized speech, head movement, arm gestures, and seated-to-standing motion while demonstrating the integration of mechanical design, controls, manufacturing, and artistic fabrication.

The final system consists of an 18-degree-of-freedom animatronic platform utilizing servo-driven facial and upper-body actuation combined with a pneumatic standing mechanism. A modular aluminum and 3D-printed structural framework was developed using SolidWorks and validated through engineering analysis. Character shells were digitally …

Mass - Modular Acoustic Suppression System, Julia Megargle, Michael A. Milner, Lucas Kaemmererer, Jonathan Corvera, Gabriel Choi, Emmi Cayer

Mechanical Engineering

The Modular Acoustic Suppression System (MASS) is a mass tuned damper that reverberates a membrane atop a cavity to absorb select acoustic frequencies produced by the Environmental Control and Life Support Systems (ECLSS) within NASA's Artemis Human Lander. The height of the reverberation chamber is adjusted to mitigate a range of varying tonal frequencies within the human lander.

Autonomous Vision-Based Litter Collection Rover, Dante Michael Benedetti, Benjamin Scott Tavares, Nathan Heil

Electrical Engineering

This report documents the design, implementation, and testing of an autonomous litter-collection rover developed as a Senior Project Design Lab (EE 460/463/464) at California Polytechnic State University. The rover integrates autonomy, computer vision, embedded real-time control, mecanum-wheel omnidirectional mobility, and a two-degree-of-freedom robotic arm to detect, approach, and collect small ground-level litter such as bottles, wrappers, and paper fragments.

The system uses a two-layer compute architecture: an NVIDIA Jetson Orin Nano running ROS 2 for perception, SLAM, and path planning, paired with an STM32L4A6ZG microcontroller for real-time motor control and odometry. The robot is built on a multi-level aluminum frame …

Elevate Grill, Brady Alexander

Electrical Engineering

The Elevate Grill Senior Project is a Santa Maria style grill with an electrical lifting/lowering mechanism and temperature sensor feedback. The grill allows for a dynamically controlled cooking surface, able to be automatically set or manually set by the user. The grill’s user interface informs the user about the temperature in different zones on the grill and alerts the user when the target temperature is hit. Additionally, the user can program preset temperature ranges and apply them to the grill’s control system. The system incorporates safe failure modes in the event of a power outage and also allows the user …

Solving Linearly Constrained Quadratic Programs Using Field Programmable Analog Arrays, Tyler Wynn, Alonzo Arroyo

Electrical Engineering

This paper presents a field-programmable analog array (FPAA) implementation for solving linearly constrained quadratic programs (LCQPs) directly in the analog domain. The solver is based on a continuous-time primal-dual control architecture with integral action, anti-windup compensation, and a piecewise-linear nonlinearity for enforcing affine inequality constraints. A switched-capacitor implementation using three AN231E04 FPAAs is developed, and coefficient scaling methods are introduced to keep internal and output signals within the voltage limits of the hardware. A global scaling factor is used to reduce internal signal excursions, while solution-space scaling is shown to modify the implemented optimization coefficients and alter the local closed-loop …

The Pid-Based Three Quadcopter Uavs Formation Control Under External Disturbance, Vo Van An, Trinh Luong Mien

Makara Journal of Technology

This paper presents the design and evaluation of a formation control strategy for three quadcopter UAVs, based on a PID controller in a leader–follower structure, under the influence of external disturbances. Each UAV employs a six-degree of-freedom dynamic model and utilises a cascade PID control architecture, in which the inner control loop stabilises the attitude. In contrast, the outer control loop regulates position and maintains the formation. The PID parameters are tuned using the Ziegler–Nichols method to ensure simple implementation and low computational cost. The performance of the control system is evaluated through simulations in the MATLAB environment for two …

Piano Aid, Christopher G. Sayers, Tyler Baugus, Gabby Taunton

Create@State

Pianos provide recreational and educational value and is a cornerstone of the culture experienced worldwide today. Despite the many benefits and enrichment music brings these benefits are often inaccessible or difficult to learn by most people but especially to those of the Deaf and Hard of Hearing (DHH) community due to its innate auditory nature. While adaptive instruments have been proposed to address this gap, many remain conceptual or fail to reach production because of high development costs and limited commercial markets. This project presents an economically feasible alternative in the design of an adaptive digital piano that enables both …

Control And Stability Analysis Of Three-Phase Grid-Connected Inverters In Renewable Energy Systems, Yasser Ayeva

Electrical Engineering and Computer Science Faculty Publications and Presentations

The increase in demand for renewable energy sources such as solar and wind systems has led to widespread use and integration of a three-phase grid connected inverters in electric modern electric power systems. The inverters are essential to convert DC power into AC power and to control the delivered power to the grid. However, the use of the inverters in a renewable energy system has some challenges related to stability and control due to the presence of power electronic interfaces and filter dynamics. This paper analyzes the control and stability of three phase grid connected inverter through an LCL filter. …

Tuning And Performance Of Pid Controlled Low Complexity Systems, Timothy Evans

Honors Theses

Proportional integral derivative (PID) controllers are used for precise position and orientation control in systems such as autonomous underwater vehicles (AUVs). This project supports the University of Southern Mississippi’s (USM) Robotics Club’s RoboSub AUV effort by developing, troubleshooting, and manually tuning PID controllers to characterize tracking performance and settling time across systems of increasing complexity. Initially, the project hypothesized that tracking performance would be reduced and settling times would increase as system complexity advanced from one degree-of-freedom (DOF) to two DOF. However, prior research was found that suggests that for small disturbances around an equilibrium state, separate PID-controlled DOFs can …

Research Of Logic Elements Based On Complementary Bipolar Transistors, Nodira Batirdjanovna Alimova, Nilufar Baxtiyorovna Gulyamova

Chemical Technology, Control and Management

Important parameters for any type of inverter – a NOT logic gate – are the power consumption during switching and the supply voltage. The proposed connection of complementary (two different types) bipolar transistors reduces the current consumption and supply voltage by simultaneously using the cutoff and saturation modes of the bipolar transistors. It has been theoretically and experimentally established that an inverter using complementary bipolar transistors operates at low supply voltages, approximately 0.7 V. Power consumption is virtually independent of the inverter's static state. A method for calculating the transfer characteristic of an inverter using complementary bipolar transistors is developed, …

The Main Errors Of The Ultrasonic Sensor In Measuring Water Flow In Open Channels, Anvar Urolovich Djalilov

Chemical Technology, Control and Management

This article analyzes the use of ultrasonic sensors in measuring water flow and the main errors that may occur in this process. In the conducted scientific research, a time-pulse ultrasonic sensor was tested. The absolute, relative and repeatability errors of the sensor during water flow measurement were studied. The absolute error represents the largest difference between the value recorded by the sensor and the real value, affecting the overall accuracy of the measurement system. This error can vary depending on environmental factors, the design and operating principles of the sensor. During the experiment, the performance of this sensor was …

Synthesis Of An Adaptive Synergistic Fuzzy Discrete Controller For Nonlinear Systems, Isamidin Xakimovich Sidikov, Gulruxsor Murot Qizi Nashvandova, Feruzakhon Botirxon Qizi Sodiqova

Chemical Technology, Control and Management

The paper considers the issues of synthesizing an adaptive fuzzy synergetic controller with discrete time for nonstationary nonlinear dynamic objects. The proposed approach is based on the integrated use of synergetic control principles and fuzzy logic methods, which ensure the formation of a control law for nonlinear dynamic objects that provides asymptotic stability of the control system. Such a hybrid combination makes it possible to guarantee the asymptotic stability of the closed-loop system and to shape the required dynamic behavior of the object over a wide range of operating modes. In addition, this approach provides the ability to adapt to …

Brrbox, Shawn J. Myers, Lane Cline, Michael Davis, Christian Secrest

Williams Honors College, Honors Research Projects

This report details the project known as “The BRRBOX”, a reusable, insulated thermoelectric cooler developed to keep internal temperatures at refrigeration levels or cooler for at least 48 hours. The cooler will track its internal temperature during this period and be able to give the data at the end of its delivery cycle to keep up with food and pharmaceutical standards during delivery. The BRRBOX uses Peltier-based cooling alongside vacuum insulation panels and fans to achieve efficient thermal control. An onboard microcontroller will monitor temperature, record the data, and adjust the cooling output to minimize power consumption. The box will …

Timing And Stability Of Uav Operations In Smart City Environments: Experimental Analysis And Design Implications, Rabia Ipek Yasar

Theses and Dissertations

This thesis investigates the deployment and performance of unmanned aerial vehicles (UAVs) within the Virginia Commonwealth University Open Cyber City (OCC) testbed. The study focuses on evaluating real-time indoor positioning performance using the Crazyflie drone platform. High-precision position measurements are obtained using the Vicon motion capture system, enabling analysis of the latency between the drone’s actual position and the system-reported position. In a closed-loop control system, the time difference between the position measurement and the application of the control command is called the system delay. Both stationary (hovering) and trajectory-following experiments are conducted to evaluate system performance. Communication delays in …

Automation And Habitat Development For A Space Based Marine Life Environment, Logan Trimmer, Alexander Hang

Harrisburg University Other Works

This project was a cross-collaboration between the Environmental Sciences and Advanced Manufacturing and Robotics programs for the company Monolith Space.

The goal of this project was to design an autonomous system to be able to track qualities of water in an aquaculture system designed to be sent to space.

Optimal & Robust Control Of A Bidirectional Dc-Dc Converter In Ev Systems, Yasser Ayeva

Electrical Engineering and Computer Science Faculty Publications and Presentations

This paper analyzes the performance of PI, LQR, and H∞ controllers for the regulation of a bidirectional buck boost converter in electric vehicle systems. To get the system state space equations, a continuous conduction average model is linearized. For analysis a PI controller will be used as baseline, the LQR controller will be used to improve transient response, and the H∞ controller will be used for the system robustness and disturbance rejection. The simulation results show that the advanced controllers surpass the PI controller in terms of overshoot, settling time, and voltage ripple, with the H∞ controller offering the best …

A Smart System For Detecting Anatomic And Histological Symptoms Of Diseased Agricultural Plants, Rustam Baratov, Himola Sunnatillayeva, Alimardon Mamatovich Mustafoqulov

Chemical Technology, Control and Management

This study describes a novel agricultural plant disease detecting smart system, capable of handling measured plant body parameters and images received by high resolution camera at the same time. The proposed plant disease detection method is based on evaluation of the signals received by measured and controlled plant body physical parameters like resistance, temperature and capacitance of the plant stem and image processing. An analogue plant model based on an electrical circuit with distributed parameters was developed. In addition, in the article the block diagram of the smart system for the early detection of plant diseases, the circuit diagram, its …

Thermal Energy Storage System Using Silica Sand As Heat Storage Medium: Simulation Of Geita Gold Mine, Santos Kihwele

Tanzania Journal of Engineering and Technology (TJET)

Currently, Geita Gold Mine (GGM) relies on electrical energy from the national grid and diesel power generators to generate electricity for various industrial applications. The plant currently spends a large amount of money on generating power from diesel generators. The total annual cost of power generation from diesel generators including lubricants is USD 56,057,990. The total annual fuel cost is USD 53,531,805 for a total of 54,985,473 liters per year. Most of the power generated by the generators is consumed in the industrial thermal processes. Thermal energy applications at the plant are thermal drying of the extracted ores to remove …

The Impacts Of Renewable Energy Sources: A Review On Grid Inertia And Frequency Regulation, Sospeter Gabriel

Tanzania Journal of Engineering and Technology (TJET)

The power system is gradually transitioning into low inertia due to integrating substantial intermittency quantity of converter-based renewable energy sources, such as wind and photovoltaic power, into the current power grid network. This integration presents significant inertia and frequency control challenges to the network as a result of a decrease in the percentage of synchronous generators. Moreover, faster frequency deviations are posed by the mismatch between the supply and demand during contingencies, which creates difficulties in preserving the frequency stability of the power system. This research explores the impacts of renewable energy sources (RESs) on grid inertia and frequency management …

Performance Enhancement Of Ev Drive System Under Open-Phase Fault Using Reinforcement Learning With Mpc, Ahmed M. Hassan, Mohammed E. Metwally Dr.

Journal of Engineering Research

Improving the operation of electric vehicles (EVs) under fault is a very important subject because it increases their ability to operate in case of an emergency. This paper proposes a fault-tolerant control methodology for an EV drive system under open phase fault (OPF). The 5-ph interior permanent magnet synchronous motor (IPMSM) is employed in the drive system because it has several merits, such as high efficiency and reliability. The proposed technique is based on utilizing a reinforcement learning (RL) control algorithm, based twin-delayed deep deterministic policy gradient (TD3) algorithm, to operate the motor at maximum torque per ampere under OPF. …

Pressure Switch Tester, Michael Starasinich, Andrew Dobson, Jordan Huschen, Mitchell Smith, Melvin Brown Iii

Honors Capstones

Abstract—- The Pressure Switch Test Stand is a comprehensive and automated testing solution designed to streamline the actuation and validation of simultaneously. At the core of the system is a PLC-controlled architecture that enables precise control and simulation of pressure conditions, replicating real-world scenarios to ensure accurate and reliable switch performance.

This test stand integrates robust mechanical fixtures, a reliable pneumatic control system, custom-designed electrical circuits, and a modular software interface, working in unison to deliver consistent and high-fidelity testing outcomes. Each pressure switch undergoes a sequence of pressure ramps and holds, with the system continuously monitoring switch states, activation …

Static Characteristics Of An Electromagnetic Three-Phase Reactive Power Sensor For Converting Asymmetric Currents, Timur Urunbayevich Kurbaniyazov

Chemical Technology, Control and Management

This article discusses the processes in the elements and structures of three-phase electromagnetic current sensors used in measuring and controlling three-phase asymmetric reactive power in power supply systems, research models of quantities and parameters, physical mechanisms, and mathematical formulas based on graphical models.

Investigation Of The Electrical Capacitance Tomography System For Determining The Spatial Distribution Of Moisture In Grain Storage, Shamte J. Kawambwa

Tanzania Journal of Engineering and Technology (TJET)

Excessive moisture content (MC) in stored grains promotes the growth of fungi and molds, which affects the quality of the grains. Effective grain monitoring methods are essential for detecting and managing grain spoilage. Electromagnetic imaging (EMI) techniques provide a promising alternative to traditional techniques by visualizing the spatial distribution of moisture within grains rather than merely average MC values offered by traditional techniques. However, existing EMI approaches often use hard-field waves, which are expensive and fragile. This study introduces an Electrical Capacitance Tomography (ECT) system that employs soft-field waves to monitor the moisture content of the grains. The system was …

Clustering Mini-Grids To Enhance Power Systems Reliability In Distributed Generation, Santos Kihwele

Tanzania Journal of Engineering and Technology (TJET)

This study investigates the effectiveness of clustering mini-grids as a method to improve the reliability and operational stability of distributed generation systems in remote areas, particularly where renewable energy sources are predominant. As renewable resources like solar and wind are increasingly integrated into mini-grids, these systems face various challenges, particularly in maintaining stable voltage and frequency across interconnected networks. Such issues are compounded by the intermittent nature of renewable energy sources and the lack of extensive communication infrastructure in rural or resource-constrained settings. To address these control challenges, this study applies droop control techniques to two mini-grids in Uganda, utilizing …

A Dynamically Efficient Predictive Controller For Voltage Stability In A Dc To Dc Boost Converter, Giovanni Reyna

Electrical and Computer Engineering ETDs

Reliable voltage regulation has become a critical issue with increase demand in modern power electronic applications. This study presents a Model Predictive Controller (MPC) for voltage regulation in DC-to-DC boost converters. A closed loop analytical MPC framework is created with the purpose of computing optimal duty cycles to maintain a stable output voltage under varying load conditions, input changes, and disturbances.

To evaluate the performance of the MPC we set the controller against a comparative analyzing with a traditional cascading proportional integral (PI) controller. The proposed controller design is specifically targeted to improve dynamic efficiency during the converter’s transient events. …

Investigation Of Dynamic Characteristics Of New Magneto-Elastic Transducers Of Mechanical Quantities, Sulton Amirov, Kamila Jurayeva

Chemical Technology, Control and Management

In the article examines the dynamic characteristics of new magnetically elastic converters of mechanical quantities by the method of parametric structural circuits. It is shown that the developed differential transformer magneto–elastic converters of power parameters in automatic monitoring and control systems act as a real differentiating link without statics, and magneto-elastic converters of motion parameters act as a whole in the form of sequentially connected oscillatory and real differentiating links. It has been established that the duration of the transient process in magnetoelastic converters of power parameters is determined by the parameters (magnetic capacitance and active magnetic resistance) of the …

Long-Range Inertia Prediction Considering Contemporary Evolution Of Power Grid Networks, Peter M. Makolo

Tanzania Journal of Engineering and Technology (TJET)

Reduced network inertia due to high penetration levels of non-synchronous generators in modern power systems is becoming a pressing issue. As a result, very quick inertial responses are observed after contingency events in networks. Due to quick inertial responses, there is a practically very limited time interval for control actions in real-time. Thus, system operators need to understand the prior inertia values to plan, control, and operate the network securely. Long-range forecasting of the network's inertia values, in contrast to short-range forecasting techniques, can pinpoint when the network is most likely to be vulnerable in a reasonable time ahead. Thus, …