Nanoscience and Nanotechnology Commons^™

Nanosized Fe2O3 On Three Dimensional Hierarchical Porous Graphene-Like Matrices As High-Performance Anode Material For Lithium Ion Batteries, Qin-Wei Zhang, Yun-Yong Li, Pei-Kang Shen

Journal of Electrochemistry

Ferric oxide (Fe₂O₃) as a promising anode material for lithium ion battery is due to its high theoretical capacity (1007 mAh·g^-1), earth abundance and low cost. The nanosized Fe₂O₃ on the three dimensional hierarchical porous graphene-like network (denoted as Fe₂O₃-3D HPG) has been synthesized by homogeneous precipitation and heat treatment. The 3D HPG can provide a highly conductive structure in conjunction to support well contacted Fe₂O₃ nanoparticles, and effectively enhance the mechanical strength of the matrices during volume changes, as well as improve the …

Sensitive Detection Of Hydroxyl Radical Based On Silver-Enhanced Gold Nanoparticle Label, Yan Yang, Peng Yu, Xiao-Hua Zhang, Jin-Hua Chen

Journal of Electrochemistry

A novel DNA-based electrochemical sensor has been successfully constructed for sensitive detection of hydroxyl radical (·OH) based on the silver-enhanced gold nanoparticle label. Thiolated DNA1 was firstly immobilized on the gold electrode through Au—S bonds. The ·OH generated from Fenton reaction could induce serious oxidative damage of the DNA1 layer on the electrode surface. Then DNA2-functionalized gold nanoparticles (DNA2-AuNPs) were linked on the electrode through the hybridization between DNA2 and undamaged DNA1. Based on the catalytic reduction of silver ion by AuNPs, a silver layer was formed on the surface of AuNPs. The quantitative assay of ·OH was carried out …

A Novel Nitrite Sensing Electrode Based On Au/Fe3O4/Chitosan Nanocomposite, Ying Dong, Yong Wang, Huan-Huan Xing, Jian-Ying Qu

Journal of Electrochemistry

A novel nitrite sensing electrode based on gold nanoparticles and iron oxides (Fe₃O₄) magnetic nanoparticles was fabricated with chitosan as the protective film on glassy carbon matrix. Experiment results showed that the sensing electrode exhibited good electrocatalytic activity toward oxidation of nitrite, and the oxidation peak current increased linearly with the concentration of nitrite varying from 5.0×10^-6 to 2.0×10^-3 mol·L^-1 (R=0.9996) with a detection limit of 7.1×10^-7 mol·L^-1 (S/N=3). The sensing electrode exhibited good sensitivity, selectivity and repeatability.

Effects Of Etchants On Surface Morphologies And Electrochemical Performance Of Iro2-Mno2 Anodic Nano-Coatings, Qing-Guo Fan, Zhi-Guo Ye, Hui-Min Meng, Chun-Min Lu

Journal of Electrochemistry

The IrO₂-MnO₂ anodic nano-coatings were prepared by the traditional thermal decomposition method on the different surfaces of Ti substrates pretreated by different etchants (HCl, H₂SO₄, C₂H₂O₄ and HF). Surface morphologies and electrochemical performance of the Ti based IrO₂-MnO₂ anodic coatings were investigated by field emission scanning electron microscopy (FESEM), cyclic voltammetry (CV) and polarization techniques. Analysis showed that the denser IrO₂ nano-particles with longer dimensions were obtained at the IrO₂-MnO₂ anodic coating surfaces on the Ti substrates etched by HF and …

Effects Of Three Dry Powder Inhalers On Deposition Of Aerosolized Medicine In The Human Oral-Pharyngeal-Laryngeal Regions, Mohammed Ali

Technology Faculty Publications and Presentations

The dry powder inhaler (DPI) is a popular, effective and convenient drug delivery device for inhalation therapy to treat asthma. However, a large quantity (approximately 54%) of inhaled aerosols deposit in the oropharyngeal region. Deposition in this region is undesirable because it provides minimum therapeutic benefits and has adverse localized or systemic side effects. This study reports a method of examining electrostatic charge effects on deposition of three DPI aerosols (Spiriva^™ Handihaler, Advair Diskus^™, and Pulmicort^™ Turbohaler) in a cadaver-based cast of the human oral-pharyngeal-laryngeal (OPL) regions. Experimental aerosols were generated from the three commercially available …

Highly-Selective Chemiresistive Sensing And Analysis Of Vapors Using Functionalized Nanotubes, Deon Hines

Dissertations, Theses, and Capstone Projects

Specifically, the project involves the development of a diversified array of nanostructured gas-sensors comprised of selectively, novel surface-functionalized carbon nanotubes (for analyte selectivity by virtue of functionality). Harnessing carbon nanotubes with various electron withdrawing and donating groups help in determining their affinity toward certain prognostic gaseous markers thus increasing specificity of such created sensors. We have devised synthetic routes that have led to the facile production of covalently polyfunctionalized nanotubes in high yield. Seven carbon nanotube analogues were systematically considered and then chemically synthesized, from pristine single-walled nanotubes (SWNT's), for use as the main component of sensory units that was …

Label-Free Detection Of Cancer Cells With Polysilicon Sensor Chips And Biomolecule-Assisted Synthesis Of Shape-Controlled Nanoparticles, Menglu Shi

Dissertations, Theses, and Capstone Projects

Constant effort has been made for the detection of cancer cells. Recently, ovarian and kidney cancer cell lines have been shown to have higher cellular elasticity as compared to normal cells assessed by monitoring the degree of deformation under hyposmotic pressure. This method has been modified and applied to various cases. In cancer cells, the oncogenic mutant p53 (mtp53) protein is present at high levels and contributes to tumor growth and metastasis. Herein the influence of mtp53 on the mechanical property of breast cancer cells was assessed by monitoring the swelling ratio of cells with time using the impedance measurements. …

Biomolecule Mediating Synthesis Of Inorganic Nanoparticles And Their Applications, Zengyan Wei

Dissertations, Theses, and Capstone Projects

Project 1.

The conventional phage display technique focuses on screening peptide sequences that can bind on target substrates, however the selected peptides are not necessary to nucleate and mediate the growth of the target inorganic crystals, and in many cases they only show moderate affinity to the targets. Here we report a novel phage display approach that can directly screen peptides catalytically growing inorganic nanoparticles in aqueous solution at room temperature. In this study, the phage library is incubated with zinc precursor at room temperature. Among random peptide sequences displayed on phages, those phages that can grow zinc oxide (ZnO) …

Efficacy Of A Magnetic Drug Delivery System And Development Of An Orthotopic Lung Tumor Imaging Model, Amber Mcbride

Nanoscience and Microsystems ETDs

The aim of this work was the development of a novel drug delivery vehicle termed nano-in-microparticles (NIMs) to evaluate the magnetic-field dependent targeting of dry powder NIMs administered endotracheally using an ex vivo and in vivo rodent model. NIMs are a novel dry powder drug delivery vehicle containing 70% lactose (w/w), 20% SPIONs (w/w) and 10% fluorescent nanospheres (w/w). Mice were insufflated with NIMs delivery vehicle in the presence of magnetic field dependent targeting to the left ventral lung after thoracotomy; controls were insufflated with the NIMs in the absence of magnetic field dependent targeting. Quantification of deposition of the …

On Thermal Aging Prevention In Polymer Core Composite Conductor Rods, Joe D. Hoffman

Electronic Theses and Dissertations

Increased energy usage in the United States and worldwide is driving the demand for new technologies to transmit electrical power in greater quantities and with reliable, safe, and more efficient methods. One recent innovation is to replace the standard Aluminum Conductor Steel Reinforced electrical transmission conductor with a new conductor design that utilizes a fiber reinforced polymer core rod to support a fully annealed aluminum conductor. This new technology that includes a hybrid carbon fiber/epoxy and glass fiber/epoxy support core allows for better efficiency and for greater current to be transmitted in the same size and weight line. These new …

Chloride Incorporation Process In Ch3Nh3Pbi3-XClX Perovskites Via Nanoscale Bandgap Maps, Jungseok Chae, Qingfeng Dong, Jinsong Huang, Andrea Centrone

Department of Mechanical and Materials Engineering: Faculty Publications

CH₃NH₃PbI_3-xCl_x perovskites enable fabrication of highly efficient solar cells. Chloride ions benefit the morphology, carrier diffusion length and stability of perovskite films; however, whether those benefits stem from the presence of Cl⁻ in the precursor solution or from their incorporation in annealed films is debated. In this work, the photothermal induced resonance (PTIR), an in situ technique with nanoscale resolution, is leveraged to measure the bandgap of CH₃NH₃PbI_3-xCl_x films obtained by a multicycle coating process that produces high efficiency (≈16 %) solar cells. Because chloride …

Role Of Interphase In The Mechanical Behavior Of Silica/Epoxy Resin Nanocomposites, Yi Hua, Linxia Gu, Sundaralingam Premaraj, Xiaodong Zhang

Department of Mechanical and Materials Engineering: Faculty Publications

A nanoscale representative volume element has been developed to investigate the effect of interphase geometry and property on the mechanical behavior of silica/epoxy resin nanocomposites. The role of interphase–matrix bonding was also examined. Results suggested that interphase modulus and interfacial bonding conditions had significant influence on the effective stiffness of nanocomposites, while its sensitivities with respect to both the thickness and the gradient property of the interphase was minimal. The stiffer interphase demonstrated a higher load-sharing capacity, which also increased the stress distribution uniformity within the resin nanocomposites. Under the condition of imperfect interfacial bonding, the effective stiffness of nanocomposites …

Biomimetic Oral Mucin From Polymer Micelle Networks, Sundar Prasanth Authimoolam

Theses and Dissertations--Chemical and Materials Engineering

Mucin networks are formed by the complexation of bottlebrush-like mucin glycoprotein with other small molecule glycoproteins. These glycoproteins create nanoscale strands that then arrange into a nanoporous mesh. These networks play an important role in ensuring surface hydration, lubricity and barrier protection. In order to understand the functional behavior in mucin networks, it is important to decouple their chemical and physical effects responsible for generating the fundamental property-function relationship. To achieve this goal, we propose to develop a synthetic biomimetic mucin using a layer-by-layer (LBL) deposition approach. In this work, a hierarchical 3-dimensional structures resembling natural mucin networks was generated …

Improving Practices In Nanomedicine Through Near Real-Time Pharmacokinetic Analysis, Isidro B. Magana

Doctoral Dissertations

More than a decade into the development of gold nanoparticles, with multiple clinical trials underway, ongoing pre-clinical research continues towards better understanding in vivo interactions. The goal is treatment optimization through improved best practices. In an effort to collect information for healthcare providers enabling informed decisions in a relevant time frame, instrumentation for real-time plasma concentration (multi-wavelength photoplethysmography) and protocols for rapid elemental analysis (energy dispersive X-Ray fluorescence) of biopsied tumor tissue have been developed in a murine model. An initial analysis, designed to demonstrate the robust nature and utility of the techniques, revealed that area under the bioavailability curve …

Ablation Of Myocardial Tissue With Nanosecond Pulsed Electric Fields, Fei Xie, Frency Varghese, Andrei G. Pakhomov, Iurii Semenov, Shu Xiao, Jonathan Philpott, Christian Zemlin

Bioelectrics Publications

Background

Ablation of cardiac tissue is an essential tool for the treatment of arrhythmias, particularly of atrial fibrillation, atrial flutter, and ventricular tachycardia. Current ablation technologies suffer from substantial recurrence rates, thermal side effects, and long procedure times. We demonstrate that ablation with nanosecond pulsed electric fields (nsPEFs) can potentially overcome these limitations.

Methods

We used optical mapping to monitor electrical activity in Langendorff-perfused New Zealand rabbit hearts (n = 12). We repeatedly inserted two shock electrodes, spaced 2–4 mm apart, into the ventricles (through the entire wall) and applied nanosecond pulsed electric fields (nsPEF) (5–20 kV/cm, 350 ns duration, …

Reconfigurable Solid-State Dye-Doped Polymer Ring Resonator Lasers, Hengky Chandrahalim, Xudong Fan

Faculty Publications

This paper presents wavelength configurable on-chip solid-state ring lasers fabricated by a single-mask standard lithography. The single- and coupled-ring resonator hosts were fabricated on a fused-silica wafer and filled with 3,3′-Diethyloxacarbocyanine iodide (CY3), Rhodamine 6G (R6G) and 3,3′-Diethylthiadicarbocyanine iodide (CY5)-doped polymer as the reconfigurable gain media. The recorded lasing threshold was ~220 nJ/mm² per pulse for the single-ring resonator laser with R6G, marking the lowest threshold shown by solid-state dye-doped polymer lasers fabricated with a standard lithography process on a chip. A single-mode lasing from a coupled-ring resonator system with the lasing threshold of ~360 nJ/mm² per pulse …

Relevance Of Blood Vessel Networks In Blast-Induced Traumatic Brain Injury, Yi Hua, Shengmao Lin, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Cerebral vasculature is a complex network that circulates blood through the brain. However, the role of this networking effect in brain dynamics has seldom been inspected. This work is to study the effects of blood vessel networks on dynamic responses of the brain under blast loading. Voronoi tessellations were implemented to represent the network of blood vessels in the brain. The brain dynamics in terms of maximumprincipal strain (MPS), shear strain (SS), and intracranial pressure (ICP) weremonitored and compared. Results show that blood vessel networks significantly affected brain responses.The increased MPS and SS were observed within the brain embedded with …

In Situ Longitudinal Pre-Stretch In The Human Femoropopliteal Artery, Alexey Kamenskiy, Andreas Seas, Grant Bowen, Paul Deegan, Anastasia Desyatova, Nick Bohlim, William Poulson, Jason N. Mactaggart

Department of Mechanical and Materials Engineering: Faculty Publications

In situ longitudinal (axial) pre-stretch (LPS) plays a fundamental role in the mechanics of the femoropopliteal artery (FPA). It conserves energy during pulsation and prevents buckling of the artery during limb movement. We investigated how LPS is affected by demographics and risk factors, and how these patient characteristics associate with the structural and physiologic features of the FPA. LPS was measured in n=148 fresh human FPAs (14–80 years old). Mechanical properties were characterized with biaxial extension and histopathological characteristics were quantified with Verhoeff-Van Gieson Staining. Constitutive modeling was used to calculate physiological stresses and stretches which were then analyzed …

Asphalt Composition, David Allen, Flavio Souza, Yong-Rak Kim, Roberto Soares

Department of Mechanical and Materials Engineering: Faculty Publications

A computational method is provided for predicting roadway failure due to degradation of the roadway over time as a function of the input loads, the roadway geometry, the material properties of the constituents in the asphaltic pavement, the shape, distribution, orientation and volume fractions of the constituents, and environmental conditions. The unique and new feature of the method is that it employs several physically based predictive methodologies simultaneously.

Extracting Continuum-Like Deformation And Stress From Molecular Dynamics Simulations, Lili Zhang, John Jasa, George Gazonas, Antoine Jerusalem, Mehrdad Negahban

Department of Mechanical and Materials Engineering: Faculty Publications

We present methods that use results from molecular dynamics (MD) simulations to construct continuum parameters, such as deformation gradient and Cauchy stress, from all or any part of an MD system. These parameters are based on the idea of minimizing the difference between MD measures for deformation and traction and their continuum counterparts. The procedures should be applicable to non-equilibrium and inhomogeneous systems, and to any part of a system, such as a polymer chain. The resulting procedures provide methods to obtain first and higher order deformation gradients associated with any subset of the MD system, and associated expressions for …