Nanoscience and Nanotechnology Commons^™

Multiscale Examination And Modeling Of Electron Transport In Nanoscale Materials And Devices, Douglas R. Banyai

Dissertations, Master's Theses and Master's Reports - Open

For half a century the integrated circuits (ICs) that make up the heart of electronic devices have been steadily improving by shrinking at an exponential rate. However, as the current crop of ICs get smaller and the insulating layers involved become thinner, electrons leak through due to quantum mechanical tunneling. This is one of several issues which will bring an end to this incredible streak of exponential improvement of this type of transistor device, after which future improvements will have to come from employing fundamentally different transistor architecture rather than fine tuning and miniaturizing the metal-oxide-semiconductor field effect transistors (MOSFETs) …

Understanding Electronic Structure And Transport Properties In Nanoscale Junctions, Kamal B. Dhungana

Dissertations, Master's Theses and Master's Reports - Open

Understanding the electronic structure and the transport properties of nanoscale materials are pivotal for designing future nano-scale electronic devices. Nanoscale materials could be individual or groups of molecules, nanotubes, semiconducting quantum dots, and biomolecules. Among these several alternatives, organic molecules are very promising and the field of molecular electronics has progressed significantly over the past few decades. Despite these progresses, it has not yet been possible to achieve atomic level control at the metal-molecule interface during a conductance measurement, which hinders the progress in this field. The lack of atomic level information of the interface also makes it much harder …

The Synthesis And Characterization Of Water-Reducible Nanoscale Colloidal Unimolecular Polymer (Cup) Particles, Cynthia J. Riddles

Doctoral Dissertations

"The coatings industry has adapted to more stringent guidelines in paint formulations. Current VOC (volatile organic compound) limits placed by the federal government have pushed the industry toward the development of paint formulations which have very little to no VOC's. The development of Colloidal Unimolecular Polymer (CUP) particles is a step in the direction of providing a resin system which exists in zero VOC aqueous dispersion.

The CUP particles are a part of the polymer field of Single Chain Nano Particles (SCNP) and ranged in diameters of 3-9 nm. The research presented in this dissertation describes the synthesis and design …

Imaging, Spectroscopy, Mechanical, Alignment And Biocompatibility Studies Of Electrospun Medical Grade Polyurethane (Carbothane™ 3575a) Nanofibers And Composite Nanofibers Containing Multiwalled Carbon Nanotubes, Faheem A. Sheikh, Javier Macossay-Torres, Travis Cantu, Xujun Zhang, M. Shamshi Hassan, M. Esther Salinas, Chakavak S. Farhangi, Hassan Ahmad, Hern Kim, Gary L. Bowlin

School of Integrative Biological & Chemical Sciences (Formerly Dept. of Chemistry)

In the present study, we discuss the electrospinning of medical grade polyurethane (Carbothane™ 3575A) nanofibers containing multi-walled-carbon-nanotubes (MWCNTs). A simple method that does not depend on additional foreign chemicals has been employed to disperse MWCNTs through high intensity sonication. Typically, a polymer solution consisting of polymer/MWCNTs has been electrospun to form nanofibers. Physiochemical aspects of prepared nanofibers were evaluated by SEM, TEM, FT-IR and Raman spectroscopy, confirming nanofibers containing MWCNTs. The biocompatibility and cell attachment of the produced nanofiber mats were investigated while culturing them in the presence of NIH 3T3 fibroblasts. The results from these tests indicated non-toxic behavior …

Integrated Nanoscale Imaging And Spatial Recognition Of Biomolecules On Surfaces, Congzhou Wang

Theses and Dissertations

Biomolecules on cell surfaces play critical roles in diverse biological and physiological processes. However, conventional bulk scale techniques are unable to clarify the density and distribution of specific biomolecules in situ on single, living cell surfaces at the micro or nanoscale. In this work, a single cell analysis technique based on Atomic Force Microscopy (AFM) is developed to spatially identify biomolecules and characterize nanomechanical properties on single cell surfaces. The unique advantage of these AFM-based techniques lies in the ability to operate in situ (in a non-destructive fashion) and in real time, under physiological conditions or controlled micro-environments.

First, AFM-based …

Systems Approach To Producing Electrospun Polyvinylidene Difluoride Fiber Webs With Controlled Fiber Structure And Functionality, Brian D. Bell

USF Tampa Graduate Theses and Dissertations

Polyvinylidene difluoride (PVDF) is a functional polymeric material that can be used for a wide variety of applications. There are many new future applications that were recently suggested for electrospun PVDF fibers. Electrospinning is a process capable of producing nano to micro sized PVDF fibers in a web. It is important to control the structure of the web during electrospinning because by controlling the structure of the web it is possible for the PVDF fiber web to have increased performance in comparison to other common forms of PVDF.

While past scientific literature focused on applications of PVDF fibers, little was …

Enhanced Magnetoimpedance And Microwave Absorption Responses Of Soft Ferromagnetic Materials For Biodetection And Energy Sensing, Jagannath Devkota

USF Tampa Graduate Theses and Dissertations

A combination of magnetic sensors with magnetic nanoparticles offers a promising approach for highly sensitive, simple, and rapid detection of cancer cells and biomolecules. The challenge facing the field of magnetic biosensing is the development of low-cost devices capable of superconducting quantum interference device (SQUID)-like field sensitivity at room temperature. In another area of interest, improving the sensitivity of existing electromagnetic field sensors for microwave energy sensing applications is an important and challenging task. In this dissertation, we have explored the excellent magnetoimpedance and microwave absorption responses of soft ferromagnetic amorphous ribbons and microwires for the development of high-performance magnetic …

The Ph Sensing Properties Of Rf Sputtered Ruo2 Thin-Film Prepared Using Different Ar/O2 Flow Ratio, Ali Sardarinejad, Devendra Kumar Maurya, Kamal Alameh

Research outputs 2014 to 2021

The influence of the Ar/O₂ gas ratio during radio frequency (RF) sputtering of the RuO₂ sensing electrode on the pH sensing performance is investigated. The developed pH sensor consists in an RF sputtered ruthenium oxide thin-film sensing electrode, in conjunction with an electroplated Ag/AgCl reference electrode. The performance and characterization of the developed pH sensors in terms of sensitivity, response time, stability, reversibility, and hysteresis are investigated. Experimental results show that the pH sensor exhibits super-Nernstian slopes in the range of 64.33-73.83 mV/pH for Ar/O₂ gas ratio between 10/0-7/3. In particular, the best pH sensing performance, in …

Reconfigurable Solid-State Dye-Doped Polymer Ring Resonator Lasers, Hengky Chandrahalim, Xudong Fan

Faculty Publications

This paper presents wavelength configurable on-chip solid-state ring lasers fabricated by a single-mask standard lithography. The single- and coupled-ring resonator hosts were fabricated on a fused-silica wafer and filled with 3,3′-Diethyloxacarbocyanine iodide (CY3), Rhodamine 6G (R6G) and 3,3′-Diethylthiadicarbocyanine iodide (CY5)-doped polymer as the reconfigurable gain media. The recorded lasing threshold was ~220 nJ/mm² per pulse for the single-ring resonator laser with R6G, marking the lowest threshold shown by solid-state dye-doped polymer lasers fabricated with a standard lithography process on a chip. A single-mode lasing from a coupled-ring resonator system with the lasing threshold of ~360 nJ/mm² per pulse …

Platinum Hollow Nanospheres With Different Sizes: Controllable Synthesis And Electrocatalytic Oxidation Toward Methanol, Xuan Lin, Mei-Qin Cheng, Zhong-Jin Shang, Ting Xiong, Xian-Tu Zhang, Wei Tian, Jian-Yun Lin, Qi-Ling Zhong, Bin Ren

Journal of Electrochemistry

The selenium (Se) templates and hollow platinum (Pthollow) nanospheres with different sizes were controllably synthesized by adjusting the concentration of sodium dodecyl sulphonate (SDSN) (CSDSN, μmol·L-1) which was used as a surfactant. Accordingly, the Pthollow nanospheres modified glassy carbon (GC) electrode (Pthollow/GC) was prepared. The morphology and composition of Pthollow nanospheres were characterized by scanning electron microscopy (SEM), transmission electron microscope (TEM), energy dispersive X-ray spectroscopy (EDX), high resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED) and X-ray diffraction (XRD) techniques. The electrocatalytic activities of Pthollow/GC and electrodeposited Pt nanoparticles modified glassy carbon electrode (Ptnano/GC) toward methanol oxidation …

Nafion/Thionine/Platinum Nanowires-Modified Electrode For Electrocatalyzing Glucose, Yu-Ping Lin, You-Xiu Lin, Qian Zhou, Dian-Ping Tang

Journal of Electrochemistry

A new amperometric biosensor based on Nafion, thionine and latinum nanowires was developed for sensitive detection of glucose. Initially, positively charged thionine molecules were immobilized onto the surface of Nafion-modified glassy carbon electrode through the interaction between -SO₃^- and -NH₃⁺, and glucose oxidase was then assembled on the modified electrode by using platinum nanowires as the cross-linkage. The preparation process was characterized by using cyclic voltammetry. Two enzymatic biosensors modified with and without platinum nanowires were used for the detection of glucose, and the improved analytical properties were obtained with platinum nanowires. Experimental results indicated …

Electrochemical Applications Of Single-Walled Carbon Nanohorns, Su-Ping Li, Huai-Min Guan, Shu-Yun Zhu, Muhammad Rehan Hassan Shah Gilani, Saima Hanif, Guo-Bao Xu, Yue-Jin Tong

Journal of Electrochemistry

Single-wall carbon nanohorns (SWCNHs) have unique properties, such as a large specific surface area, good electrical conductivity and biocompatibility. It has been widely utilized in many fields. In the present review, the progress in electrochemistry study of SWCNHs has been summarized and the future research trends have been proposed.

Direct Electrochemistry And Glucose Biosensing Of Glucose Oxidase-Gold Nanoparticles Composite Synthesized By Enzyme Method, Fang He, Xiao-Li Qin, Ying-Chun Fu, Chao Chen, Qing-Ji Xie, Shou-Zhuo Yao

Journal of Electrochemistry

Glucose oxidase (GOx)-gold nanoparticles (AuNPs) composite was synthesized by the one-pot enzyme reaction in the mixture solution of NaAuCl₄, GOx and glucose, and a Nafion/GOx-AuNPs/glassy carbon electrode was fabricated by the cast-coating method to examine the direct electrochemistry of GOx and the biosensing performance on this electrode. Such a GOx-AuNPs composite showed good direct-electrochemistry activity and bioactivity of GOx, probably because the enzyme-mediated AuNPs are close to the redox active centers of GOx. This enzyme electrode exhibited a linear amperometric response to glucose concentration (0.54 mmol·L^-1) at -0.4 V (vs. SCE), and a detection limit of …

Preparation Of Surface Molecularly Imprinted Magnetic Nanoparticles For Hemoglobin Sensing, Chun-Fang Huang, Gui-Hong Yao, Jian-Ding Qiu

Journal of Electrochemistry

Surface molecularly imprinted magnetic nanoparticles (NPs) were prepared by employing dopamine (DA) as a functional monomer, hemoglobin (Hb) as a template, H₂PtCl₆ as an oxidant triggered DA polymerization on the surface of the Fe₃O₄ NPs. The Hb and the formed platinum nanoparticles (PtNPs) were embedded into the polydopamine (PDA). After removal of the Hb, the surface molecularly imprinted magnetic nanoparticles (imprinted Fe₃O₄/PDA-PtNPs) were formed, and then simply immobilized on the magnetic glassy carbon electrode (imprinted Fe₃O₄/PDA-PtNPs/MGCE) for Hb sensing. The imprinted Fe₃O₄/PDA-PtNPs …

Laparoscopic Devices And Methods Of Using, M. Susan Hallbeck, Jakeb Riggle, Adam De Laveaga, Jake Kaufman

Department of Mechanical and Materials Engineering: Faculty Publications

A number of improvements to laparoscopic devices are described herein, primarily to improve the ergonomic functionality of the devices. For example, an articulating rod system is described, a gripping mechanism is described, and an end effector is described

Recycling Wastewater For Hydraulic Fracturing By Use Of Nanofiltration Membranes, Haley D. Cleous

Chemical Engineering Undergraduate Honors Theses

Hydraulic fracturing creates large volumes of produced water, contaminated with organics, suspended solids, and dissolved minerals. This water must either be disposed of in injection wells or treated for reuse. One option is to use a combination of ultrafiltration and nanofiltration to treat this water and reuse it in future hydraulic fracturing wells. The object of this study was to test and characterize commercial nanofiltration membranes. The work done for this project will lead to future work in modifying membranes to improve the rejection of desired components.

Photoelectric Characterization Of Bacteriorhodopsin Reconstituted In Lipid Bilayer Membrane, Joel Kamwa

Graduate Theses and Dissertations

The objective of this work was to conduct basic research in biologically inspired energy conversion solutions. A photosynthetic protein (Bacteriorhodopsin) was reconstituted in a bi-layer membrane. Then, when a laser beam was shined on the membrane, the photon energy was used by the protein to pump protons across the membrane. The translocation of protons across the membrane was measured as photocurrent. For this purpose, a system was built to characterize the lipid bilayer membranes and to measure the photocurrent. The lipid bilayer membrane was characterized by its capacitance and resistance. A picoampere photocurrent was observed when Bacteriorhodopsin protein was present …

Fabrication And Characterization Of Magnetic Nanoparticle Composite Membranes, Akeem Cruickshank

All Theses

To effectively and accurately deliver drugs within the human body, both new designs and components for implantable micropumps are being studied. Designs must ensure high biocompatibility, drug compatibility, accuracy and small power consumption. The focus of this thesis was to fabricate a prototype magnetic nanoparticle membrane for eventual incorporation into a biomedical pump and then determine the relationship between this membrane deflection and applied pneumatic or magnetic force. The magnetic nanoparticle polymer composite (MNPC) membranes in this study were composed of crosslinked polydimethylsiloxane (PDMS) and iron oxide nanoparticles (IONPs). An optimal iron oxide fabrication route was identified and particle size …

Nonequilibrium Transport Of Ionic Liquids In Electrified Nanosystems, Xikai Jiang

All Dissertations

Room-temperature ionic liquids (RTILs) are a promising class of electrolyte that are composed entirely of ions but are liquid at room temperature. Their remarkable properties such as wide electrochemical window make them ideal electrolytes in many electrochemical systems. Because the non-equilibrium transport of RTILs often determines the performance of these systems, a fundamental understanding of such transport is needed. Here, using molecular dynamic (MD) and continuum simulations, we investigated the non-equilibrium transport of RTILs in three scenarios relevant to the application of RTILs in electrochemical systems: the electroosmotic flow (EOF) of RTILs through nanochannels, the electrokinetic transport of RTILs through …

Wear Resistant Polydopamine/Ptfe Nanoparticle Composite Coating For Dry Lubrication Applications, Samuel George Beckford

Graduate Theses and Dissertations

This dissertation presents an investigation into the effect of nanoparticle fillers and a polydopamine adhesive primer on the tribological performance of thin PTFE films. The principal objective of this investigation was to reduce wear in PTFE films, an issue which precludes the use of PTFE films in tribological applications requiring high durability. The friction and wear of the composite films were evaluated using a ball-on-flat configuration in linear reciprocating motion. It was found that the use of a polydopamine adhesive primer reduces the wear of PTFE films more than 600 times. X-ray photoelectron spectroscopy (XPS) results show that a tenacious …