Engineering Plasmonic Nanostructures For Light Management And Sensing,
2019
West Virginia University
Engineering Plasmonic Nanostructures For Light Management And Sensing, Sujan Phani Kumar Kasani
Graduate Theses, Dissertations, and Problem Reports (ETD)
The two major global problems are to provide health safety and to meet energy demands for ever growing population on a large scale. The study of light interaction with nanostructures has shown a promising solution in improving the fields of bio-sensor and solar energy devices which addresses above mentioned two major global problems. Nanostructures have tunable physicochemical properties such as light absorption, electrical and thermal properties unlike bulk materials, which gives an advantage in applications like bio-sensing and energy harvesting devices. The development of nanofabrication techniques along with the discovery of Surface Enhanced Raman Scattering (SERS) and Plasmon Enhanced Fluorescence …
Structural And Optical Analysis Of Cubic Aln Nanostructure On Mgo (001) Substrate Grown By Molecular Beam Epitaxy,
2019
Graduate School
Structural And Optical Analysis Of Cubic Aln Nanostructure On Mgo (001) Substrate Grown By Molecular Beam Epitaxy, Nutthapong Discharoen
Chulalongkorn University Theses and Dissertations (Chula ETD)
The effects of an intermediate cubic GaN (c-GaN) buffer layer on structural and optical properties of AlN films grown on MgO (001) substrate by PA-MBE have been investigated. There are 2 types of c-GaN intermediated layer; the one-step buffer layer with a 7nm thick LT c-GaN layer and a two-step buffer layers with a sequence of a 7 nm-thick and 200 nm-thick c-GaN layer. The surface morphology of the AlN film with two-step growth c-GaN buffer layer exhibits the grain boundary facet like a cubic structure. While the other films exhibit the mixing of the grain boundary corresponding with the …
Numerical Study On The Dynamic Process Of Single Plume Flow In Thermal Convection With Polymers,
2019
Old Dominion University
Numerical Study On The Dynamic Process Of Single Plume Flow In Thermal Convection With Polymers, Jian-Ping Cheng, Wei-Hua Cai, Hong-Na Zhang, Feng-Chen Li, Lian Shen, Shi-Zhi Qian
Mechanical & Aerospace Engineering Faculty Publications
A direct numerical simulation of single plume flow in thermal convection with polymers was carried out in a domain with 1:3 as the width to height ratio. The heat transport ability is weakened by adding polymers within the here-investigated governing parameter range. However, it is promoted when the maximum polymer extension L is increased. The distribution of vertical velocity and temperature indicates that the plume in the polymer solution case is speeded up and widens bigger as compared to that in the Newtonian fluid case. Inside the plume, polymer chains tend to release energy at the position where the …
Magnetic Nanoparticles For Hyperthermia For Cancer Treatment,
2019
University of Texas at El Paso
Magnetic Nanoparticles For Hyperthermia For Cancer Treatment, Bianca Paola Meneses Brassea
Open Access Theses & Dissertations
Fe3O4 and NixCu4-x magnetic nanoparticles were synthesized using supercritical conditions of liquids and wet chemistry, respectively. Characterization methods (VSM, SEM, TEM, and magnetic hyperthermia) yielded results that prove feasibility for magnetic hyperthermia for cancer treatment.
Potential Of Nanoscale Elements To Control Fusarium Wilt Disease In Tomato (Solanum Lycopersicum), Enhance Macronutrient Use Efficiency, And Increase Its Yield,
2019
University of Texas at El Paso
Potential Of Nanoscale Elements To Control Fusarium Wilt Disease In Tomato (Solanum Lycopersicum), Enhance Macronutrient Use Efficiency, And Increase Its Yield, Ishaq Olarewaju Adisa
Open Access Theses & Dissertations
Nanotechnology has a great potential in ensuring food production, security and safety globally. Over the past decade, research on the use of nanomaterials to supply nutrient elements and protect plants from pest and diseases has significantly increased. Tomato (Solanum lycopersicum) is one of the most consumed vegetables in the world and United State is one of its largest producers globally generating billions of dollars annually in revenue.. Tomato plants are affected worldwide by Fusarium wilt caused by Fusarium oxysporum f. sp. Lycopersici. There is growing concern about excessive use of conventional pesticides in controlling Fusarium and other diseases in tomato …
Fabrication And Characterization Of Nanofiber Nylon-6-Mwcnt As An Electrochemical Sensor For Sodium Ions Concentration Detection In Sweat,
2019
The University of Akron
Fabrication And Characterization Of Nanofiber Nylon-6-Mwcnt As An Electrochemical Sensor For Sodium Ions Concentration Detection In Sweat, Kelsey Mills
Williams Honors College, Honors Research Projects
Fabrication and characterization nylon-6-MWCNT nanofiber as an electrochemical sensor to detect sodium ion concentrations specifically in sweat. Using contact angle to determine surface morphology and chronoamperometry testing to identify ideal sensor conditions, tests optimized parameters like weight percent of nylon or other polymers, carbon nanotube (CNT) isomer, and solution concentration to determine reproducibility of functional sensors. Utilizing the electric qualities of carbon nanotubes partnered with the sodium ion selectivity of calixarene treatment and polymers unique properties like flexibility and scalability create open an arena for optimizing sodium ion sensors for further development for functional prototypes. Morphology tests showed that the …
Resonant Acoustic Wave Assisted Spin-Transfer-Torque Switching Of Nanomagnets,
2019
Virginia Commonwealth University
Resonant Acoustic Wave Assisted Spin-Transfer-Torque Switching Of Nanomagnets, Austin R. Roe
Theses and Dissertations
We studied the possibility of achieving an order of magnitude reduction in the energy dissipation needed to write bits in perpendicular magnetic tunnel junctions (p-MTJs) by simulating the magnetization dynamics under a combination of resonant surface acoustic waves (r-SAW) and spin-transfer-torque (STT). The magnetization dynamics were simulated using the Landau-Lifshitz-Gilbert equation under macrospin assumption with the inclusion of thermal noise. We studied such r-SAW assisted STT switching of nanomagnets for both in-plane elliptical and circular perpendicular magnetic anisotropy (PMA) nanomagnets and show that while thermal noise affects switching probability in in-plane nanomagnets, the PMA nanomagnets are relatively robust to the …
High Strength, Deformable Nanotwinned Al–Co
Alloys,
2019
Purdue University
High Strength, Deformable Nanotwinned Al–Co Alloys, S. Xue, Qiang Li, D. Y. Xie, Y. F. Zhang, Han Wang, Haiyan Wong, J. Wang, Xinghang Zhang
Department of Mechanical and Materials Engineering: Faculty Publications
Aluminum (Al) alloys have been widely used in the transportation industry. However, most highstrength Al alloys to date have limited mechanical strength, on the order of a few hundred MPa, which is much lower than the flow stress of high-strength steels. In this study, we show the fabrication of nanocrystalline Al alloys with high-density growth twins enabled by a few atomic percent of Co solute. In situ uniaxial compression tests show that the flow stress of Al–Co solid solution alloys exceeds 1.5 GPa, while good work hardening capability is maintained. This study provides a new perspective on the design of …
A Sensorless Force-Feedback System For Robot-Assisted
Laparoscopic Surgery,
2019
Chinese Academy of Sciences
A Sensorless Force-Feedback System For Robot-Assisted Laparoscopic Surgery, Baoliang Zhao, Carl A. Nelson
Department of Mechanical and Materials Engineering: Faculty Publications
The existing surgical robots for laparoscopic surgery offer no or limited force feedback, and there are many problems for the traditional sensor-based solutions. This paper builds a teleoperation surgical system and validates the effectiveness of sensorless force feedback. The tool-tissue interaction force at the surgical grasper tip is estimated using the driving motor’s current, and fed back to the master robot with a position-force bilateral control algorithm. The stiffness differentiation experiment and tumor detection experiment were conducted. In the stiffness differentiation experiment, 43 out of 45 pairs of ranking relationships were identified correctly, yielding a success rate of 96%. In …
Effects Of Compositional Tailoring
On Drug Delivery Behaviours Of
Silica Xerogel/Polymer Core-Shell
Composite Nanoparticles,
2019
Hong Kong Polytechnic University
Effects Of Compositional Tailoring On Drug Delivery Behaviours Of Silica Xerogel/Polymer Core-Shell Composite Nanoparticles, Wenfei Huang, Chi Pong Tsui, Chak Yin Tang, Linxia Gu
Department of Mechanical and Materials Engineering: Faculty Publications
Conventional core-shell polymer nanoparticles usually exhibit a rapid release rate with their release kinetics mainly adjusted through changing composition of the polymer shells, limiting their applications for prolonged drug delivery. As a solution to these problems, silica xerogel/polymer core-shellstructured composite nanoparticles have been proposed. Different with our previous work centring on studying process variables, we here focused on investigating the effects of key compositional variables on essential properties of the composite nanoparticles. The drug release profiles (in vitro) were well interpreted by the Baker and Lonsdale model on a predicted two-stage basis. The first stage (<1 day) was well controlled from 18.6% to 45.9%; the second stage (1–14 days) was tailored in a range from 28.7 to 58.2% by changing the composition of the silica xerogel cores and polymeric shells. A substantial achievement was reducing the release rate by more than 40 times compared with that of conventional polymer nanoparticles by virtue of the silica xerogel cores. A semi-empirical model was also established in the first attempt to describe the effects of polymer concentration and drug loading capacity on the size of the composite nanoparticles. All these results indicated that the composite nanoparticles are promising candidates for prolonged drug delivery applications.
Unveiling The Operation Mechanism Of Layered
Perovskite Solar Cells,
2019
University of Nebraska-Lincoln
Unveiling The Operation Mechanism Of Layered Perovskite Solar Cells, Yun Lin, Yanjun Fang, Jingjing Zhao, Yuchuan Shao, Samuel J. Stuard, Masrur Morshed Nahid, Harald Ade, Qi Wang, Jeffrey E. Shield, Ninghao Zhou, Andrew M. Moran, Jinsong Huang
Department of Mechanical and Materials Engineering: Faculty Publications
Layered perovskites have been shown to improve the stability of perovskite solar cells while its operation mechanism remains unclear. Here we investigate the process for the conversion of light to electrical current in high performance layered perovskite solar cells by examining its real morphology. The layered perovskite films in this study are found to be a mixture of layered and three dimensional (3D)-like phases with phase separations at micrometer and nanometer scale in both vertical and lateral directions. This phase separation is explained by the surface initiated crystallization process and the competition of the crystallization between 3D-like and layered perovskites. …
Monolithic Heat-Transfer Device,
2019
Lincoln, NE
Monolithic Heat-Transfer Device, Sidy Ndao, George Gogos, Dennis Alexander, Troy Anderson, Craig Zuhlke
Department of Mechanical and Materials Engineering: Faculty Publications
A monolithic heat-transfer device can include a container wall configured to retain a working fluid, where the container wall is formed of a single material. The container wall also includes an interior surface configured to be in fluid communication with the working fluid. The monolithic heat-transfer device also includes a channel disposed in the interior surface of the container wall, where the channel comprises a microstructure and a nanostructure. The microstructure and the nanostructure are materially contiguous with the single material forming the container wall. In some embodiments, the nanostructure comprises one or more layers of nanoparticles. The monolithic heat-transfer …
Higher-Order Overtone Thickness-Shear
Vibrations Of Multilayered Thin-Film Acoustic
Wave Resonators And Angular Rate Sensing,
2019
Ningbo University
Higher-Order Overtone Thickness-Shear Vibrations Of Multilayered Thin-Film Acoustic Wave Resonators And Angular Rate Sensing, Hui Chen, Ji Wang, Jianke Du, Jiashi Yang
Department of Mechanical and Materials Engineering: Faculty Publications
We propose a new structure for piezoelectric gyroscopes. It is made from multilayered thin films of AlN or ZnO with alternating c-axes along the film thickness. It is shown theoretically that when such a film is electrically driven into higher-order overtone thickness-shear vibration in one of the two in-plane directions of the film and is rotating about the film normal, the Coriolis force due to the rotation causes a higher-order overtone thicknessshear vibration in a perpendicular direction with an electrical output that can be used to measure the angular rate of the rotation. Different from existing thickness-shear mode piezoelectric gyroscopes …
3d Printing Of Hybrid Mos2-Graphene Aerogels As Highly Porous Electrode
Materials For Sodium Ion Battery Anodes,
2019
Kansas State University
3d Printing Of Hybrid Mos2-Graphene Aerogels As Highly Porous Electrode Materials For Sodium Ion Battery Anodes, Emery Brown, Pengli Yan, Halil Tekik, Ayyappan Elangovan, Jian Wang, Dong Lin, Jun Li
Department of Mechanical and Materials Engineering: Faculty Publications
This study reports a 3D freeze-printing method that integrates inkjet printing and freeze casting to control both the microstructure and macroporosity via formation of ice microcrystals during printing. A viscous aqueous ink consisting of a molecular MoS2 precursor (ammonium thiomolybdate) mixed with graphene oxide (GO) nanosheets is used in the printing process. Post-treatments by freeze-drying and reductive thermal annealing convert the printed intermediate mixture into a hybrid structure consisting of MoS2 nanoparticles anchored on the surface of 2D rGO nanosheets in a macroporous framework, which is fully characterized with FESEM, TEM, XRD, Raman spectroscopy and TGA. The resulting …
Three-Dimensional Character Of The Deformation Twin In Magnesium,
2019
Shanghai Jiao Tong University & Los Alamos National Laboratory
Three-Dimensional Character Of The Deformation Twin In Magnesium, Y. Liu, P.Z. Tang, M.Y. Gong, R.J. Mccabe, J. Wang, C.N. Tome
Department of Mechanical and Materials Engineering: Faculty Publications
Deformation twins are three-dimensional domains, traditionally viewed as ellipsoids because of their two-dimensional lenticular sections. In this work, we performed statistical analysis of twin shapes viewing along three orthogonal directions: the ‘dark side’ (DS) view along the twin shear direction (η1), the twinning plane normal (TPN) view (k1) and the ‘bright side’ (BS) view along the direction λ(=k1 × η1). Our electron back-scatter diffraction results show that twins in the DS and BS views normally exhibit a lenticular shape, whereas they show an irregular shape in the TPN view. Moreover, the findings in the TPN view revealed that twins grow …
Spatiotemporal Characterizations Of Spontaneously Beating Cardiomyocytes With Adaptive Reference Digital Image Correlation,
2019
University of Nebraska-Lincoln
Spatiotemporal Characterizations Of Spontaneously Beating Cardiomyocytes With Adaptive Reference Digital Image Correlation, Akankshya Shradhanjali, Brandon D. Riehl, Bin Duan, Ruiguo Yang, Jung Yul Lim
Department of Mechanical and Materials Engineering: Faculty Publications
We developed an Adaptive Reference-Digital Image Correlation (AR-DIC) method that enables unbiased and accurate mechanics measurements of moving biological tissue samples. We applied the AR-DIC analysis to a spontaneously beating cardiomyocyte (CM) tissue, and could provide correct quantifications of tissue displacement and strain for the beating CMs utilizing physiologically-relevant, sarcomere displacement length-based contraction criteria. The data were further synthesized into novel spatiotemporal parameters of CM contraction to account for the CM beating homogeneity, synchronicity, and propagation as holistic measures of functional myocardial tissue development. Our AR-DIC analyses may thus provide advanced non-invasive characterization tools for assessing the development of spontaneously …
Insulating Tunneling Contact For Efficient And Stable Perovskite Solar Cells,
2019
Lincoln, NE
Insulating Tunneling Contact For Efficient And Stable Perovskite Solar Cells, Jinsong Huang, Xiaopeng Zheng, Qi Wang, Yang Bai, Qingfeng Dong
Department of Mechanical and Materials Engineering: Faculty Publications
Perovskite-based photoactive devices, such as solar cells, include an insulating tunneling layer inserted between the perovskite photoactive material and the electron collection layer to reduce charge recombination and concomitantly provide water resistant properties to the device.
Beyond The Toolpath: Site-Specific Melt Pool Size Control Enables Printing Of Extra-Toolpath Geometry In Laser Wire-Based Directed Energy Deposition,
2019
Oak Ridge National Laboratory
Beyond The Toolpath: Site-Specific Melt Pool Size Control Enables Printing Of Extra-Toolpath Geometry In Laser Wire-Based Directed Energy Deposition, Brian T. Gibson, Bradley S. Richardson, Tayler W. Undermann, Lonnie J. Love
Department of Mechanical and Materials Engineering: Faculty Publications
A variety of techniques have been utilized in metal additive manufacturing (AM) for melt pool size management, including modeling and feed-forward approaches. In a few cases, closed-loop control has been demonstrated. In this research, closed-loop melt pool size control for large-scale, laser wire-based directed energy deposition is demonstrated with a novel modification, i.e., site-specific changes to the controller setpoint were commanded at trigger points, the locations of which were generated by the projection of a secondary geometry onto the primary three-dimensional (3D) printed component geometry. The present work shows that, through this technique, it is possible to print a specific …
Disposable Fluidic Self-Propelling Robot For Traversing A Tubular Passage,
2019
Lincoln, Ne
Disposable Fluidic Self-Propelling Robot For Traversing A Tubular Passage, Carl Nelson, Benjamin Terry, Abolfazl Pourghodrat, Hossein Dehghani, Dmitry Oleynikov, Prithviraj Dasgupta
Department of Mechanical and Materials Engineering: Faculty Publications
A probe for traversing a tubular passage includes an introducer to be supported at an entrance to the tubular passage. The probe also includes a probe tip to traverse the tubular passage, and a tube with an inflatable tube segment. In some embodiments, the inflatable tube segment is storable in the probe tip. The inflatable tube segment is configured to be inflated to push the probe tip away from the introducer toward an end on the tubular passage. In some embodiments, the probe includes a sealing mechanism, whre the sealing mechanism can be positioned between the inflatable tube segment of …
Mechanical Stresses Associated With Flattening Of Human Femoropopliteal Artery Specimens During Planar Biaxial Testing And Their Effects On The Calculated Physiologic Stress-Stretch State,
2019
University of Nebraska-Lincoln
Mechanical Stresses Associated With Flattening Of Human Femoropopliteal Artery Specimens During Planar Biaxial Testing And Their Effects On The Calculated Physiologic Stress-Stretch State, Majid Jadidi, Anastasia Desyatova, Jason N. Mactaggart, Alexey Kamenskiy
Department of Mechanical and Materials Engineering: Faculty Publications
Planar biaxial testing is commonly used to characterize the mechanical properties of arteries, but stresses associated with specimen flattening during this test are unknown. We quantified flattening effects in human femoropopliteal arteries (FPAs) of different ages, and determined how they affect the calculated arterial physiologic stress-stretch state. Human FPAs from 472 tissue donors (age 12-82 years, mean 53±16 years) were tested using planar biaxial extension, and morphometric and mechanical characteristics were used to assess the flattening effects. Constitutive parameters for the invariant-based model were adjusted to account for specimen flattening, and used to calculate the physiologic stresses, stretches, axial force, …
