Nanoscience and Nanotechnology Commons^™

Exploration Of Efficient Scintillation Based On Inas Quantum Dots In A Gaas Matrix, Katherine Rose Dropiewski

Legacy Theses & Dissertations (2009 - 2024)

Scintillation and optical properties of an integrated InAs/GaAs Quantum Dot (QD) Scintillation Detector were investigated to improve efficiency and reduce the decay time of luminescence. The photoluminescent properties of InAs QDs embedded in a GaAs matrix were studied as-grown by molecular beam epitaxy (MBE) on GaAs substrates, and on foreign substrates fabricated as thick (10-25 μm) waveguides. The luminescent efficiency of QDs as-grown on GaAs substrates were examined using photoluminescence (PL) measurements at room temperature and the thermal quenching of PL was analyzed by comparing the integrated PL intensities at 77K-400K. PL measurements were used to optimize QD AlAs capping, …

Energetic And Exergetic Analysis Of A Heat Pipe Evacuated Tube Solar Collector Using Mwcnt/Water Nanofluid, Mahmoud Eltaweel, Ahmed A. Abdel-Rehim

Mechanical Engineering

Increasing the energy demand and the limited availability of conventional energy sources are the main challenges to secure the human future. Solar energy is an attractive source of energy to ensure the sustainability of energy in this world for now and for the future. Evacuated tube solar collector is a solar thermal collector mostly used for domestic applications. The replacement of the working fluid with nanofluid can enhance the heat transfer even for low temperature applications. The effect of multi-walled carbon nanotubes and water nanofluid as working fluid in evacuated tube solar collector is used to experimentally investigate the energy …

Modification Of The Optical Response Of Alpha Quartz Via The Deposition Of Gold Nanoparticles In Etched Ion Tracks, Maria C. Garcia Toro

Doctoral Dissertations

”This study addresses the experimental methods used to develop and characterize plasmonic devices capable of modifying the optical response of alpha quartz via the deposition of gold nanoparticles in etched ion tracks. In the first part of the research, the microstructural characterization of latent and etched ion tracks produced in alpha quartz (α-SiO₂) is presented. Single crystals of α-SiO₂ were irradiated with two highly energetic ions to different nominal fluences. As expected, the morphology of the resulting ion tracks depends on the energy of the incident ion and their stopping powers within the target material. Subsequent chemical …

Improvement Of Zno Doping Properties Via Sputtering Process With Gas-Timing Technique, Nattaya Tajina Yossapong

Chulalongkorn University Theses and Dissertations (Chula ETD)

In order to obtain high quality of ZnO thin film on plastic and glass substrate for applying to the production of flexible devices, ZnO thin film was investigated by using LP-ZnO buffer layer and gas-timing technique with RF magnetron sputtering at low or room temperature without heat treatment. Growing ZnO thin film directly on plastic substrate without buffer layer, the result was cracking, cavity and wrinkling film. The first part, the effect of buffer layer was studied by growing homo-buffer layer with low-power on plastic substrate and growing main film with high-power on top of that layer calling 2 step …

Tunable-Focus Liquid Lens Through Charge Injection, Shizhi Qian, Wenxiang Shi, Huai Zheng, Zhaohui Liu

Mechanical & Aerospace Engineering Faculty Publications

Liquid lenses are the simplest and cheapest optical lenses, and various studies have been conducted to develop tunable-focus liquid lenses. In this study, a simple and easily implemented method for achieving tunable-focus liquid lenses was proposed and experimentally validated. In this method, charges induced by a corona discharge in the air were injected into dielectric liquid, resulting in “electropressure” at the interface between the air and the liquid. Through a 3D-printed U-tube structure, a tunable-focus liquid lens was fabricated and tested. Depending on the voltage, the focus of the liquid lens can be adjusted in large ranges (−∞ to −9 …

Coarse-Grained Dynamically Accurate Simulations Of Ionic Liquids At Vacuum-Interface, Tyler D. Stoffel

Theses and Dissertations--Mechanical and Aerospace Engineering

Ionic liquids, possessing improved properties in many areas of technical application, are excellent candidates as components in development of next-generation technology, including ultra-high energy batteries. If they are thus applied, however, extensive interfacial analysis of any selected ionic configuration will likely be required. Molecular dynamics (MD) provides an advantageous route by which this may be accomplished, but can fall short in observing some phenomena only present at larger time/length scales than it can simulate. Often times this is approached by coarse-graining (CG), with which scope of simulation can be significantly increased. However, coarse-grained MD systems are generally known to produce …

Magnetism In Γ-Fesi2 Nanostructures: A First Principles Study, Sahil Dhoka

Dissertations, Master's Theses and Master's Reports

First-principles calculations are performed on γ-FeSi₂ nanostructures grown on Si (111) and (001) substrate. An attempt to explain the origin of emergent magnetic properties of the metastable gamma phase of iron di-silicide (γ-FeSi₂) is made, which show ferromagnetic behavior on nanoscale, unlike its possible bulk form. Many papers try to explain this magnetism from factors like bulk, epitaxial strain, interface, surface, edges, and corners but doesn’t provide an analytical study for these explanations. Density functional theory is used to analyze the magnetic effects of these factors. The results for the epitaxial structures show no magnetic behavior for …

Multiscale Modeling Of Carbon Fibers/Graphene Nanoplatelets/Epoxy Hybrid Composites For Aerospace Applications, Hashim Al Mahmud

Dissertations, Master's Theses and Master's Reports

Significant research effort has been dedicated for decades to improve the mechanical properties of aerospace polymer-based composite materials. Lightweight epoxy-based composite materials have increasingly replaced the comparatively heavy and expensive metal alloys used in aeronautical and aerospace structural components. In particular, carbon fibers (CF)/graphene nanoplatelets (GNP)/epoxy hybrid composites can be used for this purpose owing to their high specific stiffness and strength. Therefore, this work has been completed to design, predict, and optimize the effective mechanical properties of CF/GNP/epoxy composite materials at different length scales using a multiscale modeling approach. The work-flow of modeling involves a first step of using …

Paper-Based Point-Of-Care Tools For Blood Testing, Xuefei Gao

Graduate Theses, Dissertations, and Problem Reports (ETD)

Early detection of malignant disease is crucial for timely diagnosis and effective medical intervention, which significantly increases survival rates and reduce financial burden on patients. Biomarkers are becoming increasingly important in detection of malignant diseases, because they can be employed for indicating diseases, predicting risks and monitoring the progression of diseases. In addition, biomarkers show up at early stages of diseases in human tissues and fluids (e.g., blood, urine and saliva), which shows great promise for early disease detection. In this dissertation, paper-based lateral flow strips (PLFSs) have been developed for the detection of disease biomarkers, including protein biomarkers and …

Sequence-Coded Coherent Laser Ranging With High Detection Sensitivity, Keren Shemer, Gil Bashan, H Hagai Diamandi, Yosef London, Tzur Raanan, Yochai Israelashvili, Alon Charny, Itzik Cohen, Arik Bergman, Nadav Levanon, Avi Zadok

Advanced Science Research Center

The compression of extended, coded sequences allows for laser ranging measurements with low peak power levels. Previous realizations of this approach were restricted by additive noise of direct, incoherent detection. In this work we bring together pulse sequence coding and optical coherent detection to achieve very high sensitivity. Collected sequences with an overall energy equivalent to only 800 photons are successfully compressed. The observed sensitivity agrees with analytic predictions. Compared with incoherent detection, measurement durations are reduced by four orders of magnitude. The protocol is suitable for laser ranging over tens of kilometers, depending on atmospheric conditions.

Advanced Electrodes And Electrolytes For Long-Lived And High-Performance Lithium-Sulfur Batteries, Deepesh Gopalakrishnan

Wayne State University Dissertations

ABSTRACT

ADVANCED ELECTRODES AND ELECTROLYTES FOR LONG-LIVED AND HIGH-PERFORMANCE LITHIUM-SULFUR BATTERIES

by

DEEPESH GOPALAKRISHNAN

August 2020

Advisor: Dr. Leela Mohana Reddy Arava

Major: Mechanical Engineering

Degree: Doctor of Philosophy

Lithium – Sulfur (Li-S) batteries have received much attention and considered as a promising candidate for next generation energy storage devices because of their high theoretical energy density (≈2600 Wh kg‒1) and environmental friendliness. However, the uncontrollable growth of lithium dendrites in the lithium metal anode and the fatal effect of polysulfide shuttle hinder their practical applications. The formation of dendrites during repeated Li plating/stripping processes results in: reduced Li availability …

Synthesis Of Ruthenium Bipyridine Conjugated Antibiotic For Fluorescence Lifetime Imaging And Spectroscopy Aided Tracking In Citrus, Ryan Parente

Electronic Theses and Dissertations, 2020-2023

Antibiotic treatment of systemic bacterial plant pathogens is an established practice in many crops; however, in citrus it has only recently become available for growers to utilize against Huanglongbing disease. The preliminary efficacy of these treatments is uncertain due to the inability to track their presence in phloem. The need to monitor their movement in planta, especially their presence and translocation in vascular tissue, is a necessary step in clarifying their effectiveness. Previous work has shown the value of Fluorescence Lifetime Imaging (FLIM) in distinguishing between fluorescent probes and plant tissue autofluorescence, which is normally a barrier in photochemical studies …

The Synthesis Of Palladium-Platinum Core-Shell Nanoparticles With High Catalytic Peroxidase Activities For Biosensing Applications, Edwin Davidson

Electronic Theses and Dissertations, 2020-2023

In recent years, peroxidase mimic nanostructures have attracted special interest due to their low cost, high stability, and high catalytic activity. Herein, we demonstrate the use of Pd-Pt nanocubes (NCs) to achieve the rapid and sensitive colorimetric detection of ascorbic acid (AA), commonly known as vitamin C. The colored signal generated by the catalyzed oxidation of 3,3',5,5'-tetramethylbenzidine (TMB) by the decomposition of hydrogen peroxide (H2O2) is quenched in the presence of AA based on its antioxidant property. This colorimetric method attains a detection limit of 0.40 µM and a linear range from 0 to 15 µM, with good linearity. To …

Additive Manufacturing Of Magnesium Alloys, Rakeshkumar Karunakaran, Sam Ortgies, Ali Tamayol, Florin Bobaru, Michael P. Sealy

Department of Mechanical and Materials Engineering: Faculty Publications

Magnesium alloys are a promising new class of degradable biomaterials that have a similar stiffness to bone, which minimizes the harmful effects of stress shielding. Use of biodegradable magnesium implants eliminates the need for a second surgery for repair or removal. There is a growing interest to capitalize on additive manufacturing's unique design capabilities to advance the frontiers of medicine. However, magnesium alloys are difficult to 3D print due to the high chemical reactivity that poses a combustion risk. Furthermore, the low vaporization temperature of magnesium and common biocompatible alloying elements further increases the difficulty to print fully dense structures …

Formulation And Validation Of Nanoparticle Controlled Delivery For Chemotherapeutic Drug Products, Shani L. Levit

Theses and Dissertations

Taxol, a formulation of paclitaxel (PTX), is one of the most widely used anticancer drugs, particularly for treating recurring ovarian carcinomas following surgery. Clinically, PTX is used in combination with other drugs such as lapatinib (LAP) to increase treatment efficacy. Delivering drug combinations with nanoparticles has the potential to improve chemotherapy outcomes. In this study, we use Flash NanoPrecipitation, a rapid, scalable process to encapsulate weakly hydrophobic drugs (logP in vitro. Encapsulating either PTX or LAP into nanoparticles increases drug potency. When PTX and LAP are co-loaded in the same nanoparticle, they have a synergistic effect that is greater than …

Electric Field Control Of Fixed Magnetic Skyrmions For Energy Efficient Nanomagnetic Memory, Dhritiman Bhattacharya

Theses and Dissertations

To meet the ever-growing demand of faster and smaller computers, increasing number of transistors are needed in the same chip area. Unfortunately, Silicon based transistors have almost reached their miniaturization limits mainly due to excessive heat generation. Nanomagnetic devices are one of the most promising alternatives of CMOS. In nanomagnetic devices, electron spin, instead of charge, is the information carrier. Hence, these devices are non-volatile: information can be stored in these devices without needing any external power which could enable computing architectures beyond traditional von-Neumann computing. Additionally, these devices are also expected to be more energy efficient than CMOS devices …

Nanostructured Metal Thin Films As Components Of Composite Membranes For Separations And Catalysis, Michael J. Detisch

Theses and Dissertations--Chemical and Materials Engineering

Novel metallic thin film composite membranes are synthesized and evaluated in this work for improved separations and catalysis capabilities. Advances in technology that allow for improved membrane performance in solvent separations are desirable for low molecular weight organic separation applications such as those in pharmaceutical industries. Additionally, the introduction of catalytic materials into membrane systems allow for optimization of complex processes in a single step. By adding a nanostructured metallic thin film to its surface, a polymer membrane may be modified to exhibit these improved properties. Using magnetron sputtering, thin metal films may be deposited on commercially available membranes to …

Synthesis Of Metal Oxide Surface And Interface Arrays By A Combined Solid-Liquid- Vapor/Vapor-Liquid-Solid Approach, Alexandra J. Riddle

Theses and Dissertations--Chemistry

This project was motivated by an in situ heating experiment in the transmission electron microscope (TEM) in which gold (Au) nanoparticles were observed to dissolve tin dioxide (SnO2) nanowires (NWs) under vacuum. The explanation for this observation was that the high-temperature and low-pressure environment of the TEM caused the reverse reaction of the well-known vapor-liquid-solid (VLS) method commonly used to grow NWs. In the VLS process, a metal catalyst absorbs reactant vapor until it becomes supersaturated. The precipitation of the NW occurs at the liquid-solid interface, which ceases when there is no longer reactant vapor, and the diameter of the …

Patenting Fast And Slow: Examiner And Applicant Use Of Prior Art, Shine Sean Tu

Cardozo Arts & Entertainment Law Journal

Previous studies have shown that an applicant's ability to obtain a patent is inexorably linked to the random assignment of a patent examiner.1 However, not all patent examiners are created equal. Some patent examiners allow patent applications quickly within just one or two Office Actions, resulting in only a few months of substantive patent prosecution. In contrast, other patent examiners constantly reject patents applications, which can result in unnecessarily delaying prosecution and years of substantive patent prosecution. This study focuses on how different examiners use prior art rejections to prolong or compact prosecution.

Prior art rejections are one of the …

Impact Of Chain Architecture On The Thickness Dependence Of Physical Aging Rate Of Thin Polystyrene Films, Gregory Brown, Elizabeth Lewis, Bryan D. Vogt

Williams Honors College, Honors Research Projects

The dynamics of polymer thin films have been demonstrated to be significantly altered from the bulk, but the origins of such differences are not well defined. In this work, we seek to understand the differences in the structural dynamics (or physical aging) of polystyrene (PS) through branching and other well defined architectures (comb and centipede). The aging dynamics of ultrathin films (< 30 nm) differ from relatively thick films (100-150nm) with linear PS thin films aging more rapidly than the relatively “bulk-like” thick films. Ellipsometric measurements are used to characterize the physical aging rate of the films. The change in film thickness and refractive index as the films are held below the glass transition temperature (T_g) provides a simple measure of the physical aging. In this study, four different architectures (linear, comb, 4 arm star, and centipede) will be investigated. For each PS architecture, the aging rate will be determined for film …