Nanoscience and Nanotechnology Commons^™

Fabrication, Development, And Characterization Of Hipco Swcnt - Alginate Hydrogel Composites For Cellular Product Applications, Fabian Armando Alvarez-Primo

Open Access Theses & Dissertations

In this study, we designed, synthesized, and characterized ultrahigh purity single-walled carbon nanotube (SWCNT)-alginate hydrogel composites. Among the parameters of importance in the formation of an alginate-based hydrogel composite with single-walled carbon nanotubes, are their varying degrees of purity, their particulate agglomeration and their dose-dependent correlation to cell viability, all of which have an impact on the resultant compositeâ??s efficiency and effectiveness towards biomedical applications. To promote their homogenous dispersion by preventing agglomeration of the SWCNT, at first, we used three different surfactants-sodium dodecyl sulfate (SDS-anionic), cetyltrimethylammonium bromide (CTAB-cationic), and Pluronic F108 (nonionic). After experimentation and corroboration through evidence obtained …

Transient Electrochemical Surface-Enhanced Raman Spectroscopic Study In Electrochemical Reduction Of P-Nitrothiophenol, Yun Ling, Jing Tang, Guo-Kun Liu, Cheng Zong

Journal of Electrochemistry

P-nitrothiophenol (PNTP) is one of the most common probe molecules studied by surface-enhanced Raman spectroscopy (SERS). The research in electrochemical reduction behavior of PNTP will help understanding the mechanism for the nitrobenzene reduction. In this paper, we used transient electrochemical surface-enhanced Raman spectroscopy (TEC-SERS) to study the SERS of PNTP with cyclic voltammetry and chronoamperometry on gold electrodes. The results show that the TEC-SERS provide a time resolution that equals the transient electrochemical methods, and we concluded that the reaction was so quick that we did not observe the spectral information of intermediate species described in the literatures with a …

Electrochemical Preparation And Photocatalytic Performance Of Lanio3/Tio2 Nanotube Arrays, Cheng Gong, Ze-Yang Zhang, Si-Wan Xiang, Lan Sun, Chen-Qing Ye, Chang-Jian Lin

Journal of Electrochemistry

The LaNiO₃/TiO₂ nanotube arrays were prepared by pulse electrodeposition combined with high temperature annealing. The LaNiO₃ nanoparticles modified on the TiO₂ nanotube arrays had small particle size (< 10 nm), uniform distribution and controllable loading. Some LaNiO₃ nanoparticles were deposited inside the TiO₂ nanotubes. The UV-visible absorption spectra displayed that the absorption band edge of LaNiO₃/TiO₂ nanotube arrays was obviously red-shifted as compared with that of TiO₂ nanotube arrays, and the visible light absorption was enhanced significantly. The photocatalytic degradation results of rhodamine B (RhB) under visible light showed that the LaNiO₃/TiO₂ nanotube arrays prepared …

Electrochemical Sensor Based On Magnetic Electrode Modified With Magnetic Molecularly Imprinted Nanoparticles Immobilized Hemoglobin For Determination Of Hydrogen Peroxide, Yang Yuan, Jia-Xin Wang, Yu-Hua Cao

Journal of Electrochemistry

In this work, the surface-imprinted technique was used to prepare magnetic hemoglobin (Hb) imprinted nanoparticles, using Fe₃O₄@SiO₂ NPs as the carrier, Hb as the template molecule, and tetraethyl orthosilicate (TEOS) as the imprinted polymer monomer. The nanoparticles had a core-shell structure, with magnetic Fe₃O₄ NPs as the core and Hb imprinted polymers as the shell. Therefore, Hb could be concentrated and fixed on the surface of the magnetic imprinted nanoparticles (MMIPs NPs). Furthermore, MMIPs NPs were immobilized with chitosan (CS) on the surface of a magnetic electrode to constitute Hb enzyme-like biosensor …

An Aptasensor Based On Aunps/Pani/Tnts Nanocomposite For Electrochemical Detection Of Tobramycin, Yong-Ling Nong, Ni-Na Qiao, Ying Liang

Journal of Electrochemistry

A novel well-constructed electrochemical aptamer-based sensor for the detection of tobramycin was presented, using differential pulse voltammetry (DPV) as a detection technique and methylene blue(MB) as an electrochemical indicator. A glassy carbon electrode modified with a nanocomposite of Au nanoparticles/polyaniline/titania nanotubes (AuNPs/PANI/TNTs) was constructed as the electrode scaffold. The nanocomposite was characterized by transmission electron microscopy and X-ray photoelectron spectroscopy in detail. The results of cyclic voltammetry and electrochemical impedance measurements demonstrated that the AuNPs/PANI/TNTs nanocomposites can improve greatly the electron transfer on the interface. For the detection of tobramycin, the DPV results showed a linear relationship between the current …

Generalized Ultrasonic Scattering Model For Arbitrary Transducer Configurations, Andrea P. Arguelles, Joseph A. Turner

Department of Mechanical and Materials Engineering: Faculty Publications

Ultrasonic scattering in polycrystalline media is directly tied to microstructural features. As a result, modeling efforts of scattering from microstructure have been abundant. The inclusion of beam modeling for the ultrasonic transducers greatly simplified the ability to perform quantitative, fully calibrated experiments. In this article, a theoretical scattering model is generalized to allow for arbitrary source and receiver configurations, while accounting for beam behavior through the total propagation path. This extension elucidates the importance and potential of out-of-plane scattering modes in the context of microstructure characterization. The scattering coefficient is explicitly written for the case of statistical isotropy and ellipsoidal …

Anomalous Stranski-Krastanov Growth Of (111)-Oriented Quantum Dots With Tunable Wetting Layer Thickness, Christopher F. Schuck, Simon K. Roy, Trent Garrett, Paul J. Simmonds

Materials Science and Engineering Faculty Publications and Presentations

Driven by tensile strain, GaAs quantum dots (QDs) self-assemble on In_0.52Al_0.48As(111)A surfaces lattice-matched to InP substrates. In this study, we show that the tensile-strained self-assembly process for these GaAs(111)A QDs unexpectedly deviates from the well-known Stranski-Krastanov (SK) growth mode. Traditionally, QDs formed via the SK growth mode form on top of a flat wetting layer (WL) whose thickness is fixed. The inability to tune WL thickness has inhibited researchers’ attempts to fully control QD-WL interactions in these hybrid 0D-2D quantum systems. In contrast, using microscopy, spectroscopy, and computational modeling, we demonstrate that for GaAs(111)A QDs, we …

Generalized Ultrasonic Scattering Model For Arbitrary Transducer Configurations, Andrea P. Arguelles, Joseph A. Turner

Department of Mechanical and Materials Engineering: Faculty Publications

Ultrasonic scattering in polycrystalline media is directly tied to microstructural features. As a result, modeling efforts of scattering from microstructure have been abundant. The inclusion of beam modeling for the ultrasonic transducers greatly simplified the ability to perform quantitative, fully calibrated experiments. In this article, a theoretical scattering model is generalized to allow for arbitrary source and receiver configurations, while accounting for beam behavior through the total propagation path. This extension elucidates the importance and potential of out-of-plane scattering modes in the context of microstructure characterization. The scattering coefficient is explicitly written for the case of statistical isotropy and ellipsoidal …

Ultrasonic Wave Propagation In Copper/Graphene Metal Matrix Composites, Casey Lindbloom

Mechanical Engineering Undergraduate Honors Theses

Emerging metallic composite materials implanted with graphene sheets are showing immense promise, with benefits being observed with regards to mechanical, thermal, and electrical material properties. This research aims to investigate the effects on ultrasonic wave propagation in Copper/Graphene Metal Matrix Composites (Cu/Gr MMCs) with varying graphene arrangements inspired from nacre and bone nanoscale material distributions. To accomplish this, the molecular dynamics (MD) method is utilized to simulate nanoscale wave propagation on a set of Cu/Gr MMCs with differing graphene arrangements and volume percentages ranging up to 4.56%. The computational model results are then analyzed to determine the variation in energy …

In Silico Sequence Optimization For The Reproducible Generation Of Dna Structures, Michael D. Tobiason

Boise State University Theses and Dissertations

Biologically, deoxyribonucleic acid (DNA) molecules have been used for information storage for more than 3 billion years. Today, modern synthesis tools have made it possible to use synthetic DNA molecules as a material for engineering nanoscale structures. These self-assembling structures are capable of both resolutions as fine as 4 angstroms and executing programed dynamic behavior. Numerous approaches for creating structures from DNA have been proposed and validated, however it remains commonplace for engineered systems to exhibit unexpected behaviors such as low formation yields, poor performance, or total failure. It is plausible that at least some of these behaviors arise due …

Synthesis Of Cellulose Nanocrystal-Gold Nanoparticle Hybrid System For Surface Plasmon-Enhanced Property, Mahshid Iraniparast

Graduate Theses and Dissertations

Gold nanoparticles (AuNPs) have been brought to the forefront of various applications, ranging from theranostics, to organic photovoltaics, to biosensing owing to their localized surface plasmon resonance (LSPR) property. However, this property needs to be improved in order to allow for high sensitivity and quantitative detection of biomolecules. Hybrids of AuNPs with low-dielectric cellulose nanocrystal (CNCs) would yield enhancement of the LSPR property, which is driven by the confinement of electron oscillation at their interfaces. This study proposed a seed-mediated growth method to synthesize hybrids of CNCs-AuNPs. Sulfate groups on the surface of CNCs served as the sites for the …

Studies Of Initial Growth Of Gan On Inn, Alaa Alnami

Graduate Theses and Dissertations

III-nitride materials have recently attracted much attention for applications in both the microelectronics and optoelectronics. For optoelectronic devices, III-nitride materials with tunable energy band gaps can be used as the active region of devices to enhance the absorption or emission. A such material is indium nitride (InN), which along with gallium nitride (GaN) and aluminum nitride (AlN) embody the very real promise of forming the basis of a broad spectrum, a high efficiency solar cell. One of the remaining complications in incorporating InN into a solar cell design is the effects of the high temperature growth of the GaN crystal …

Quantitative Study Of The Antimicrobial Effects Of Silver On The Motility Of Escherichia Coli, Benjamin Russell

Graduate Theses and Dissertations

In recent decades, the number of antibiotic-resistant bacterial infections has grown to become a serious global threat. This rise can be attributed to the widespread misuse of antibiotics and the lack of newly developed drugs to fight resistant organisms. Novel bactericidal substances have, therefore, garnered significant research interest. Silver, due to its powerful antimicrobial effects, is one such substance. Silver is typically most effective in cationic form; however, advancements in nanotechnology have paved the way for the controlled fabrication of nano-silver. Silver nanoparticles have been shown to have increased antibacterial potency for a variety of reasons, including the release of …

Optimized Production And Evaluation Of Cellulose Nanocrystals Derived From Pre-Extracted Kraft Pulp Of Different Wood Species, Gurshagan Kandhola

Graduate Theses and Dissertations

Production of nanocellulose from a variety of naturally abundant, locally available and industrially significant wood species provides an opportunity for diversifying the portfolio of traditional pulp and paper industries. The U.S. has a prolific forest products industry with a well-established infrastructure that could be utilized for optimized and customized production of cellulose nanomaterials. However, to achieve that, it is important to a) understand how biorefining strategies for complete fractionation of biomass affect the downstream processing of pulp into nanocellulose, b) maximize the yields of cellulose nanocrystals and nanofibers (CNCs and CNFs) from pretreated raw materials, and c) evaluate if the …

Effects Of Temperature And Nitrogen Depletion On Biodiesel Production Under Saline Conditions By A Mixed Algal Community, Sarah J. Kintner

Nanoscience and Microsystems ETDs

The overall objective addressed in this research was to gain a better understanding of how native mixed cultures of phototrophic microorganisms from a saline system may be used for biodiesel production. Laboratory batch reactors were grown under variable temperatures and nitrogen concentrations with original inoculum from a hypersaline pond in central New Mexico. Growth at 40 C° led to lower lipid production, lower nitrate consumption, and less diverse communities than growth at 20° C. All communities were dominated by the cyanobacteria Plectonema except the in second experiment, where they were only 30% of the culture. In a second experiment with …

Gamma-Ray Radiation Effects In Graphene-Based Transistors With H-Bn Nanometer Film Substrates, E. J. Cazalas, Michael R. Hogsed, S. R. Vangala, Michael R. Snure, John W. Mcclory

Faculty Publications

Radiation effects on graphene field effect transistors (GFETs) with hexagonal boron nitride (h-BN) thin film substrates are investigated using 60Co gamma-ray radiation. This study examines the radiation response using many samples with varying h-BN film thicknesses (1.6 and 20 nm thickness) and graphene channel lengths (5 and 10 μm). These samples were exposed to a total ionizing dose of approximately 1 Mrad(Si). I-V measurements were taken at fixed time intervals between irradiations and postirradiation. Dirac point voltage and current are extracted from the I-V measurements, as well as mobility, Dirac voltage hysteresis, and the total number of GFETs that remain …

Optical Angular Scatterometry: In-Line Approach For Roll-2-Roll And Nano-Imprint Fabrication Systems, Juan Jose Faria-Briceno

Electrical and Computer Engineering ETDs

As critical dimensions continue to shrink and structures become more complex, metrology processes are challenging to implement during in-line nanomanufacturing. Non-destructive, non-contact, and high-speed conditions are required to achieve proper metrology processes during in-line manufacturing. Optical scatterometry is a nanoscale metrology tool widely used in integrated circuit manufacturing for characterization and quality control. However, most applications of optical scatterometry operate off-line. A high-speed, in-line, non-contact, non-destructive scatterometry angular system has been demonstrated in this work to scan pattern surfaces during real-time nano-fabrication.

Our system has demonstrated scanning capabilities using flat, 1D and 2D complex structures. The flat surface samples consist …

Novel Silica Filled Deep Eutectic Solvent Based Nanofluids For Energy Transportation, Changhui Liu, Hui Fang, Xinjian Liu, Ben Xu, Zhonghao Rao

Mechanical Engineering Faculty Publications

Liquid range of nanofluids is a crucial parameter as it intensively determines their application temperature scope. Meanwhile, improved thermal conductivity and stability are of great significances and comprise the main fundamental research topics of nanofluids. In this work, 2-butoxy-3,4-dihydropyran (DP), produced from a convenient one-pot three-component reaction in water, was employed as dual lipophilic brusher and metal nanoparticle anchor. It was found that DP was able to enhance the dispersing ability and thermal conductivity of SiO2 nanoparticle filled deep eutectic solvent (DES) based nanofluids simultaneously. The key to the success of this protocol mainly relies on the electrophilic property and …

Novel Silica Filled Deep Eutectic Solvent Based Nanofluids For Energy Transportation, Changhui Liu, Hui Fang, Xinjian Liu, Ben Xu, Zhonghao Rao

School of Integrative Biological & Chemical Sciences (Formerly Dept. of Chemistry)

Liquid range of nanofluids is a crucial parameter as it intensively determines their application temperature scope. Meanwhile, improved thermal conductivity and stability are of great significances and comprise the main fundamental research topics of nanofluids. In this work, 2- butoxy-3,4-dihydropyran (DP), produced from a convenient one-pot three-component reaction in water, was employed as dual lipophilic brusher and metal nanoparticle anchor. It was found that DP was able to enhance the dispersing ability and thermal conductivity of SiO2 nanoparticle filled deep eutectic solvent (DES) based nanofluids simultaneously. The key to the success of this protocol mainly relies on the electrophilic property …

Multi-Scale Modeling Of The Lamellar Unit Of Arterial Media, Hozhabr Mozafari, Lulu Wang, Yuguo Lei, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

The heterogeneity of the lamellar unit (LU) of arterial media plays an important role in the biomechanics of artery. Current two-component (fibrous component and a homogenous matrix) constitutive model is inappropriate for capturing the micro-structural variations in the LU, such as contraction/relaxation of vascular smooth muscle cells (VSMCs), fragmentation of the elastin layer, and deposition/disruption of the collagen network. In this work, we developed a representative volume element (RVE) model with detailed micro-configurations, i.e., VSMCs at various phenotypes, collagen fibers, and elastin laminate embedded in the ground substance. The fiber architecture was generated based on its volume fraction and orientations. …