Geological Engineering Commons^™

The Use Of Electrical Resistivity Tomography (Ert) To Delineate Water-Filled Vugs Near A Bridge Foundation, Jeremiah Chukwunonso Obi

Masters Theses

"A structural support was needed to strengthen the load-bearing capacity of an unnamed bridge foundation in Laclede County in South-Central Missouri due to increasing traffic volume and age of the bridge. This area is characterized by karstic features such as losing streams, underground caves and sinkholes. During the construction of a drilled shaft for the substructure, a few feet north of the north footing of the pier, voids were noted beneath a roughly 2 foot thick cap of dolomite rock. Because of this, there were concerns about the integrity of the rock beneath the existing bridge foundation. Consequently, subsurface investigation …

Analyses Of Surface Wave Seismic Data And Supplemental Borehole And Electrical Resistivity Tomography Control, Mengxing Li

Masters Theses

"Multichannel analyses of surface wave (MASW) data and electrical resistivity tomography (ERT) control were acquired at two test sites in central Missouri. Limestone bedrock existed at both test sites at variable depths. The ground surface at both test sites was relatively flat.

The primary objective was to map the variable depth to the top of the rock based on shear-wave velocity contrasts. ERT data and borehole control were acquired at each site in order to constrain the interpretation of the MASW data.

The MASW method proved to be more effective than the ERT method in terms of mapping soil layers …

Performance Characterization And Optimization Of Microgrid-Based Energy Generation And Storage Technologies, Joe D. Guggenberger Ii

Doctoral Dissertations

"Renewable energy-powered microgrids have proven to be a valuable technology for self-contained (off-grid) energy systems. Characterizing microgrid system performance pre-deployment would allow the system to be appropriately sized to meet all required electrical loads at a given renewable source operational time frequency. A vanadium redox battery was empirically characterized to determine operating efficiency as a function of charging characteristics and parasitic load losses. A model was developed to iteratively determine system performance based on known weather conditions and load requirements. A case study was performed to compare modeled system performance to measurements taken during operation of the microgrid system. Another …

Influence Of Capillary Heterogeneity On Leakage Of Co2 From A Borehole, Frank Roecker

Electronic Theses and Dissertations

We used a modified invasion percolation (MIP) model to examine the effect of capillary heterogeneity, buoyancy forces, and viscous forces on the surface area and saturation of a CO2 plume leaking into a shallow aquifer. The purpose of this study is to provide a better understanding of how CO 2 migrates from a borehole, which is essential in implementing effective simulation and monitoring regimes to accurately detect CO2 leakage from sequestration sites. The MIP model approach will simulate invasion of a light non-wetting fluid (e.g., CO2) into a medium initially saturated with a dense wetting fluid (water). The style of …

Visualizing And Modeling Interior Spaces Of Dangerous Structures Using Lidar, Norbert H. Maerz, T. K. Assebaum, Dustin J. Williams, K. Shea, Yongjian Xi, Xiaoling Li, Ye Duan

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

LIght Detection and Ranging (LIDAR) scanning can be used to safely and remotely provide intelligence on the interior of dangerous structures for use by first responders that need to enter these structures. By scanning into structures through windows and other openings or moving the LIDAR scanning into the structure, in both cases carried by a remote controlled robotic crawler, the presence of dangerous items or personnel can be confi rmed or denied. Entry and egress pathways can be determined in advance, and potential hiding/ambush locations identifi ed. This paper describes an integrated system of a robotic crawler and LIDAR scanner. …

Capture Zone Modeling For Photovoltaic Microgrid Powered Pump And Treat Remediation, John Patrick Conroy

Masters Theses

"Remediation systems protect human health and the environment by removing harmful contaminants from the environment. Pump and treat groundwater remediation systems typically rely on utility power to continuously pump contaminated groundwater to an above ground treatment unit. However, the use of renewable energy (solar and wind) for a pump and treat remediation system can reduce the output of harmful greenhouse gases and the need for coal-based utility power.

This paper describes a hypothetical renewable energy powered pump and treat remediation system that uses an off-grid photovoltaic array to power a submersible solar water pump. The pump operates on an intermittent …

Saturation Effects On Mechanical Excavatability Of Roubidoux Sandstone Under Selected Rock Cutting Tools, Muhammad Zubair Abu Bakar

Doctoral Dissertations

"This study investigated the differences in the cutting performance of two rock cutting tools in dry and saturated rock. For this purpose, a permeable quartzose sandstone was subjected to a series of full scale linear rock cutting tests, in both dry and saturated conditions, using a constant cross-section (CCS) disc cutter and a radial drag pick at a constant cutting speed.

In this rock, saturation with water reduced the forces acting on the disc cutter by 27-48% (significant at 90% confidence), but also reduced the chip yield by nearly as much. Even though the specific energy of fragmentation went down …

Surface Expressions Of Discontinuities, And The Estimation Of Their 3-D Orientations Using Combined Lidar And Optical Imaging, James Nii Aboh Otoo

Doctoral Dissertations

"The importance of the collection and analysis of data on discontinuities cannot be overemphasized. Problems which include sampling difficulties, risks, limited access to rock faces and exposures, and the delay in data collection has led to a high need for data collection tools and analysis techniques that can overcome these problems.

Discontinuities manifest themselves as either traces or as facets. Traces are linear features that intersect with both the discontinuity and the rock cut. Facets are the actual discontinuity surfaces that are exposed in the rock cut. Facets can be natural or induced. Identifying a facet as either natural or …

Ethane, Ethyne And Carbon Monoxide Concentrations In The Upper Troposphere And Lower Stratosphere From Ace And Geos-Chem: A Comparison Study, G. González Abad, N. D.C. Allen, P. F. Bernath, C. D. Boone, S. D. Mcleod, G. L. Manney, G. C. Toon, C. Carouge, Y. Wang, Shiliang Wu, X

Michigan Tech Publications, Part 1

Near global upper tropospheric concentrations of carbon monoxide (CO), ethane (C2H6) and ethyne (C2H2) from ACE (Atmospheric Chemistry Experiment) Fourier transform spectrometer on board the Canadian satellite SCISAT-1 are presented and compared with the output from the Chemical Transport Model (CTM) GEOS-Chem. The retrievals of ethane and ethyne from ACE have been improved for this paper by using new sets of microwindows compared with those for previous versions of ACE data. With the improved ethyne retrieval we have been able to produce a near global upper tropospheric distribution of C2H2 from space. Carbon monoxide, ethane and ethyne concentrations retrieved using …

Opportunistic Validation Of Sulfur Dioxide In The Sarychev Peak Volcanic Eruption Cloud, S. Carn, T. M. Lopez

Michigan Tech Publications, Part 1

We report attempted validation of Ozone Monitoring Instrument (OMI) sulfur dioxide (SO 2) retrievals in the stratospheric volcanic cloud from Sarychev Peak (Kurile Islands) in June 2009, through opportunistic deployment of a ground-based ultraviolet (UV) spectrometer (FLYSPEC) as the volcanic cloud drifted over central Alaska. The volcanic cloud altitude (∼12-14 km) was constrained using coincident CALIPSO lidar observations. By invoking some assumptions about the spatial distribution of SO 2, we derive averages of FLYSPEC vertical SO 2 columns for comparison with OMI SO 2 measurements. Despite limited data, we find minimum OMI-FLYSPEC differences within measurement uncertainties, which support the validity …

Sulphur Dioxide As A Volcanic Ash Proxy During The April-May 2010 Eruption Of Eyjafjallajökull Volcano, Iceland, H. E. Thomas, A. J. Prata

Michigan Tech Publications, Part 1

The volcanic ash cloud from the eruption of Eyjafjallajökull volcano in April and May 2010 resulted in unprecedented disruption to air traffic in Western Europe causing significant financial losses and highlighting the importance of efficient volcanic cloud monitoring. The feasibility of using SO2 as a tracer for the ash released during the eruption is investigated here through comparison of ash retrievals from the Spinning Enhanced Visible and Infrared Imager (SEVIRI) with SO2 measurements from a number of infrared and ultraviolet satellite-based sensors. Results demonstrate that the eruption can be divided into an initial ash-rich phase, a lower intensity middle phase …

A Deterministic Method Of Predicting Long-Term Pile Capacity In Cohesive Soils After The Dissipation Of Excess Pore Water Pressure, Eric J. Steward

Doctoral Dissertations

Pile setup or freeze is a phenomenon where the bearing capacity of a pile increases over time both during and after the dissipation of pore pressure and the stabilization of lateral earth pressure. Driven piles gain capacity after installation because of the dissipation of excess pore pressure and soil aging. Incorporating accurate setup prediction into the design of the piles can significantly reduce the cost of many projects by reducing the size or number of required piles. Various simple, empirical mathematical models have been developed to predict pile setup. However, these models are often unreliable, resulting in very conservative designs. …

Impacts Of Future Climate Change And Effects Of Biogenic Emissions On Surface Ozone And Particulate Matter Concentrations In The United States, Y. F. Lam, J. S. Fu, S. Wu, L. J. Mickley

Michigan Tech Publications, Part 1

Simulations of present and future average regional ozone and PM 2.5 concentrations over the United States were performed to investigate the potential impacts of global climate change and emissions on regional air quality using CMAQ. Various emissions and climate conditions with different biogenic emissions and domain resolutions were implemented to study the sensitivity of future air quality trends from the impacts of changing biogenic emissions. A comparison of GEOS-Chem and CMAQ was performed to investigate the effect of downscaling on the prediction of future air quality trends. For ozone, the impacts of global climate change are relatively smaller when compared …

Determination Of Time-And Height-Resolved Volcanic Ash Emissions And Their Use For Quantitative Ash Dispersion Modeling: The 2010 Eyjafjallajökull Eruption, A. Stohl, A. J. Prata, S. Eckhardt, L. Clarisse, A. Durant, S. Henne, N. I. Kristiansen, A. Minikin, U. Schumann, P. Seibert, K. Stebel, H. E. Thomas, T. Thorsteinsson, K. Tørseth, B. Weinzierl

Michigan Tech Publications, Part 1

The Aprilg-May, 2010 volcanic eruptions of Eyjafjallajökull, Iceland caused significant economic and social disruption in Europe whilst state of the art measurements and ash dispersion forecasts were heavily criticized by the aviation industry. Here we demonstrate for the first time that large improvements can be made in quantitative predictions of the fate of volcanic ash emissions, by using an inversion scheme that couples a priori source information and the output of a Lagrangian dispersion model with satellite data to estimate the volcanic ash source strength as a function of altitude and time. From the inversion, we obtain a total fine …

Effect Of Additive On The Performance Characteristics Of Centrifugal And Progressive Cavity Slurry Pumps With High Concentration Fly Ash Slurries, Sunil Chandel, S.N. Singh, V. Seshadri

Coal Combustion and Gasification Products Journal Archive

Slurry pumps that are used in the hydraulic transportation of fly ash slurries through pipes in thermal power plants can be broadly classified into two main categories namely positive displacement and centrifugal pumps. The two types of pumps differ considerably in construction as well as in operating principle compared to the conventional pumps. The present study reports the effect of additive on the performance characteristics of centrifugal and progressive cavity screw pumps with fly ash slurries at high concentrations (above Cw < 50% by weight). Mixture of sodium carbonate and Henko detergent (5:1) at a concentration of 0.2% by weight has been used as an additive. For each type of pump, the effect of additive on the performance characteristics has been experimentally evaluated at rated speed with fly ash slurries in the concentration range of 50 to 70% by weight. The pump total head, overall efficiency and pump input power as a function of flow rate have been measured. The results obtained from the centrifugal slurry pump performance show that at rated speed, the performance of the pump improves with the addition of drag reducing additive. In the case of progressive cavity screw pump, pump performance characteristics and behavior were completely different as compared to the centrifugal slurry pump. At rated speed, the performance of screw pump deteriorates with the addition of drag reducing soap solution.

Zinc Speciation In Power Plant Burning Mixtures Of Coal And Tires, Luis F.O. Silva, Marcos L.S. Oliveira, Carmen Serra, James C. Hower

Coal Combustion and Gasification Products Journal Archive

Fly ash from the cyclone-boiler co-combustion of high-S, high volatile bituminous coal and tire-derived fuel (tdf) was studied using a variety of chemical, optical, and microbeam techniques. Fly ash, dominated by Al-Si glass with lesser amounts of coalderived carbons, Fe-spinels, and tire-derived carbons, has Zn concentrations ranging from 2200 ppm (1st ESP row) to 6900 ppm Zn (3rd ESP row). Zinc occurs in Zn-rich nanoparticles in the Al-Si glass phases and as ZnO in amorphous and crystalline nanominerals, Fe- and Zn-sulfides, Pb-Al-Fe sulfates, and Zn sulfates. Iron-rich, Al- and Ti-bearing spinels contain accessory Zn2+,Cr3+,Mn2+, and Pb2+. Fe-sulfates and phosphates nanoparticles …

Co-Disposal Of Dry Fgd By-Product With Coal Gasification Ash And Inorganic Brines, Jabulani S. Mahlaba, P.C. Pretorius, Subal Maharajh, M.P. Augustyn

Coal Combustion and Gasification Products Journal Archive

There is a growing pressure from the environmental authorities and public bodies to reduce anthropogenic pollution. Stringent environmental legislation is being implemented for industries around the world, even more so for coal consuming industries. Control of gaseous emissions is one of the areas that are receiving considerable attention towards sustainable development. Coal combustion in coal-fired power utilities emits SO~x~ to the atmosphere. Dry flue gas desulphurisation (FGD) is a well known technology often used to mitigate sulphur emissions in coal-fired power utilities. It traditionally uses lime to neutralise SO~x~, and forms a mixture of anhydrite (CaSO~4~), and calcium sulphite (CaSO~3~). …

A Multi-Analytical Approach To Understand The Chemistry Of Fe-Minerals In Feed Coals And Ashes, Marcos L.S. Oliveira, Frans Waanders, Luis F.O. Silva, Andre Jasper, Carlos H. Sampaio, Dursman Mchabe, Rachel S. Hatch, James C. Hower

Coal Combustion and Gasification Products Journal Archive

Seven feed coals used in the Brazilian power generation industry were obtained and subsequently analysed together with fly ash and bottom ash from a major Brazilian power plant. The samples were investigated by means of room temperature FeMo¨ssbauer analyses, X-ray diffraction, Raman spectroscopy, scanning electron microscope and petrographic analysis. In addition, nanometer-sized crystalline phases in coals and ashes were characterised using an energy-dispersive X-ray spectrometer and a high-resolution transmission electron microscope. The major identified Fe-bearing minerals in the coals were found to be actinolite, ankerite, chalcopyrite, chlorite, goethite, illite, ilmenite, magnesioferrite, natrojarosite, pyrite, pyrrhotite, and siderite; whilst in the fly …

Compositional Variations In Pilot Gasifier And Laboratory-Produced Slags And Their Impacts On Slag Viscosity And Coal Assessment, Alexander Ilyushechkin, Daniel Roberts, David Harris

Coal Combustion and Gasification Products Journal Archive

The flow behaviour of coal mineral matter at high temperatures is an important parameter for coal use in entrained-flow gasification technologies. Recently, gasification performance data was obtained from a series of pilot-scale gasification tests on a suite of well-characterised Australian black coals. Evaluation of the results of the pilot tests and the detailed laboratory investigations provided the opportunity for evaluation of the practical applicability of different laboratory and modelling techniques for coal assessment in terms of mineral matter behaviour in entrained flow gasification. A series of viscosity measurements was made over the range 1200–1600uC using slags produced in a pilot …

Compaction Of High-Ca Fly Ash-Al- And Al-Alloy-Composites: Evaluation Of Their Microstructure And Tribological Performance, Grigorios Itskos, Angeliki Moutsatsou, Pradeep K. Rohatgi, Nikolaos Koukouzas, Charalampos Vasilatos, Eleni Katsika

Coal Combustion and Gasification Products Journal Archive

In this study, highly calcareous and siliceous fly ash particles were utilized for the fabrication of Al- and Al-alloy-based MetalMatrix Composites (MMCs) by means of powder metallurgy. After compacting and sintering Al and Al/Si powders containing 10, 15, and 20wt. % ash particles, the homogenous (and with minimal amount of voids) microstructure of the produced composites was verified by means of Scanning Electron Microscopy (SEM). The composites were tested for their dry sliding wear behavior using a pin-on-disc machine against spheres of alumina. The worn surfaces of composites were then examined by using SEM and Energy Dispersive X-Ray Spectroscopy (EDS). …