Geological Engineering Commons^™

Non-Invasive Imaging And Assessment Of Pavements, Adel Mohamed Elkrry

Doctoral Dissertations

"Eight electrical resistivity tomography (ERT) and multi-channel analysis of surface wave (MASW) case studies are presented. The objective is to assess the condition of pavement, base, native soil, and rock all the way down to the top of the bedrock. Each segment of road way is approximately 1000 ft. long. The cases include US 63 north of Rolla, US 54 in Camden County, Rte. 179 in Jefferson City, HWY AT in Franklin County, I-55 in Pemiscot County, I-55 in Perry County, HWY U in Dent County, I-35 in Daviess County. In addition, there are only three types of pavement in …

Advanced Approaches For Bridge Deck Assessment Using Ground Penetrating Radar, Aleksey Kamilevich Khamzin

Doctoral Dissertations

"Ground penetrating radar (GPR) data were acquired across four bridge decks with the objective of developing an advanced workflow for GPR operation that would allow the bridge owners to estimate repair quantities for certain bridge decks, based on GPR data. The primary contributions from this research are as follows: 1. It was demonstrated that the conditions of bridge decks can be cost-effectively and efficiently assessed using the GPR tool. 2. The GPR tool's ability to provide rapid and reliable results in comparison with conventional bridge deck condition assessment techniques was established. 3. The qualitative and quantitative relationships between the GPR …

Microstructure And Geotechnical Properties Of St. Peter Sandstone In Clayton, Iowa, Amir Hossein Bagherieh

Doctoral Dissertations

"The St. Peter Sandstone is significantly different from the minerals and rocks which have been studied extensively in mining. It is brittle and characterized by an unusually high friction angle. On the other hand it is friable, and it is nearly cohesionless. The scarcity of the ground control techniques for this particular mining environment has created many difficulties for mine operators. This research aims to establish a fundamental understanding of the basic mechanical and strength properties of the St. Peter Sandstone for engineering design and scientific research. The specific objectives are 1) characterizing the strength of the St. Peter Sandstone, …

Determining Rockfall Volumes In Three Sites Along Habs Mountain Road In Southwestern Saudi Arabia, Using Lidar Technology, Abdullah Ayed Al-Otaibi

Masters Theses

"The rugged elevated topography is a characteristic feature of the western and southwestern regions of Saudi Arabia. Few arterial roads connect the scattered villages of these regions to major cities, such as Habs Road in Jazan region. Rock fall poses a serious hazard to people, property and animals along the rock cuts of this road. Although no traditional Rockfall studies have previously been applied to this road, accessibility and rock formation shape and structure variability influenced the choice of using Terrestrial Light Detection And Ranging (LiDAR) technology to calculate the volume of rockfall at selected sites along this road.

Software …

A New Technique For Modeling The Geomorphology Of A Slow Moving, Soft-Slope Landslide Using Terrestrial Lidar, Nathan Bradley Rohrbaugh

Masters Theses

"Soft slope movement is a big problem whether it involves an engineered slope, one that is near infrastructure, or both. Active landslides that fail slowly sometimes allow ample time to affect remedial works. In order to plan effective remedial works, there needs to be a model of the entire geometry of the slide. This thesis describes a new approach to evaluate the morphology of slope geometry using Light Detection and Ranging (LiDAR) data obtained from simple targets strategically positioned on a slide body. The data was gathered in three-month intervals over a period of one year to allow enough time …

Optimum Acquisition And Processing Parameters For Multichannel Analysis Of Surface Waves Using 3d Electrical Resistivity Tomography As Control, Uchenna Chibuzo Nwafor

Masters Theses

"Multichannel Analysis of Surface Waves (MASW) and Electrical Resistivity Tomography (ERT) data were acquired in the Newburg, Missouri with the goal of determining optimum MASW acquisition parameters. Users of the MASW tool generally state that greater geophone intervals and greater shot-to-receiver offsets provide for more accurate results. The objective was to determine if this "rule of thumb" applies in karst terrain.

ERT data were acquired along four traverses with eighty-four (84) electrodes at five feet spacing with SuperSting R8 Resistivity System using dipole- dipole array. The data were processed using Earth Imager to generate 2-D resistivity inversion and thereafter, Voxler …

Empirical Modeling Of Piping Along Mississippi River Levees In Southwestern Illinois, Rebecca F. Shields

Electronic Theses and Dissertations

No abstract provided.

Modeling Roughness Of Rock Discontinuity Surfaces, Christopher Pickering

Electronic Theses and Dissertations

The aim of this thesis is to propose a new methodology of quantifying the rock discontinuity condition of roughness through the physically based modeling approach of signal analysis. The development of this method came about after investigation into the use of qualitative categorizations of roughness from the RMR rating system within rock engineering system matrices. In an attempt to assign significant values to these generalized qualitative descriptions, the standard joint roughness coefficient (JRC) profiles were initially examined through basic measurements, such as aperture and ramp angle. Following these initial measurements and identification of inconsistencies in the wave parameters of the …

Characterizing The Influence Of Carbon On The Flowrate And Disinfection Efficacy Of Household Ceramic Water Filters, Jessie Yvonne Hahn

Masters Theses

"Drinking water contamination is a major cause of disease in developing countries. Point of Use (POU) water treatment technologies generally have low initial cost and allow rapid availability of improved water. Ceramic pot filters (CPFs) are a POU water source treatment technology which filter water by gravity through a porous ceramic media. Some filters in use contain carbon remnants left from the fugitive pore former as a dark carbon core. Using disk-shaped experimental ceramic filters produced in the lab to have varying levels of carbon, the percent carbon present was measured and a visual analysis method was developed to determine …

Development Of A Stochastic Model For Performance Characterization Of A Pv/Vrb Microgrid, Kayla M. Speidel

Masters Theses

"Photovoltaic (PV) Microgrids have been proven to be a useful technology in providing an environmentally friendly source of energy when compared to the use of fossil fuels. Accurately characterizing the performance of a microgrid system would ensure that the system is appropriately sized to meet electrical loads without a heavy reliance on diesel generators. A microgrid that is sized properly will reduce the cost of diesel fuel, while also reducing the risk of wasting money on an oversized system. A deterministic model which was created to characterize the performance of PV microgrids based on percent of time generator running was …

Non-Destructive And Destructive Bridge Deck Condition Assessment, Aleksandra V. Varnavina

Doctoral Dissertations

"The dissertation is composed of three papers, which cover the lack of information on the specific aspects of non-destructive and destructive bridge deck assessment.

In the first paper, appropriate data acquisition and processing parameters for concrete bridge deck condition assessment using ground-coupled ground penetrating radar are developed. The use of proposed parameters helps to significantly reduce acquisition and processing time, while providing engineers with reliable and detailed information on the condition of bridge deck.

In the second paper, a novel approach to develop relationship between GPR data and concrete removal depth measurements collected after hydrodemolition is proposed. A linear relationship …

Separation Of Ash And Sulfur Dioxide During The 2011 Grímsvötn Eruption, E. D. Moxnes, N. I. Kristiansen, A. Stohl, L. Clarisse, A. J. Durant, K. Weber, A. Vogel

Michigan Tech Publications, Part 1

Modeling the transport of volcanic ash and gases released during volcanic eruptions is crucially dependent on knowledge of the source term of the eruption, that is, the source strength as a function of altitude and time. For the first time, an inversion method is used to estimate the source terms of both volcanic sulfur dioxide (SO2) and ash. It was applied to the explosive volcanic eruption of Grímsvötn, Iceland, in May 2011. The method uses input from the particle dispersion model, FLEXPART (flexible particle dispersion model), a priori source estimates, and satellite observations of SO2 or ash total columns from …

Absorption And Fluorescence Properties Of Chromophoric Dissolved Organic Matter Of The Eastern Bering Sea In The Summer With Special Reference To The Influence Of A Cold Pool, E. J. D'Sa, J. I. Goes, H. Gomes, C. Mouw

Michigan Tech Publications, Part 1

The absorption and fluorescence properties of chromophoric dissolved organic matter (CDOM) are reported for the inner shelf, slope waters and outer shelf regions of the eastern Bering Sea during the summer of 2008, when a warm, thermally stratified surface mixed layer lay over a cold pool ( < 2 °C) that occupied the entire middle shelf. CDOM absorption at 355 nm (ag355) and its spectral slope (S) in conjunction with excitation-emission matrix (EEM) fluorescence and parallel factor analysis (PARAFAC) revealed large variability in the characteristics of CDOM in different regions of the Bering Sea. PARAFAC analysis aided in the identification of three humic-like (components one, two and five) and two protein-like (a tyrosine-like component three, and a tryptophan-like component four) components. In the extensive shelf region, average absorption coefficients at 355 nm (ag355, mg-1) and DOC concentrations (μM) were highest in the inner shelf (0.342 ± 0.11 mg-1, 92.67 ± 14.60 μM) and lower in the middle (0.226 ± 0.05 mg-1, 78.38 ± 10.64 μM) and outer (0.185 ± 0.05 mg-1, 79.24 ± 18.01 μM) shelves, respectively. DOC concentrations, however were not significantly different, suggesting CDOM sources and sinks to be uncoupled from DOC. Mean spectral slopes S were elevated in the middle shelf (24.38 ± 2.25 μmg-1) especially in the surface waters (26.87 ± 2.39 μmg-1) indicating high rates of photodegradation in the highly stratified surface mixed layer, which intensified northwards in the northern middle shelf likely contributing to greater light penetration and to phytoplankton blooms at deeper depths. The fluorescent humic-like components one, two, and five were most elevated in the inner shelf most likely from riverine inputs. Along the productive "green belt" in the outer shelf/slope region, absorption and fluorescence properties indicated the presence of fresh and degraded autochthonous DOM. Near the Unimak Pass region of the Aleutian Islands, low DOC and ag355 (mean 66.99 ± 7.94 μM; 0.182 ± 0.05 mg-1) and a high S (mean 25.95 ± 1.58 μmg-1) suggested substantial photobleaching of the Alaska Coastal Water, but high intensities of humic-like and protein-like fluorescence suggested sources of fluorescent DOM from coastal runoff and glacier meltwaters during the summer. The spectral slope S vs. ag355 relationship revealed terrestrial and oceanic end members along with intermediate water masses that were modeled using nonlinear regression equations that could allow water mass differentiation based on CDOM optical properties. Spectral slope S was negatively correlated (r2 = 0.79) with apparent oxygen utilization (AOU) for waters extending from the middle shelf into the deep Bering Sea indicating increasing microbial alteration of CDOM with depth. Although our data show that the CDOM photochemical environment of the Bering Sea is complex, our current information on its optical properties will aid in better understanding of the biogeochemical role of CDOM in carbon budgets in relation to the annual sea ice and phytoplankton dynamics, and to improved algorithms of ocean color remote sensing for this region.

Seasonal Variability And Long-Term Evolution Of Tropospheric Composition In The Tropics And Southern Hemisphere, K. M. Wai, S. Wu, A. Kumar, H. Liao

Michigan Tech Publications, Part 1

Impacts on tropospheric composition in the tropics and the Southern Hemisphere from biomass burning and other emission sources are studied using a global chemical transport model, surface measurements and satellite retrievals. Seasonal variations in observed CO at remote island sites are examined. Easter Island (eastern Pacific Ocean) is impacted indirectly by the hemispheric zonal transport of CO due to the burning in southern Africa/South America, via the westerlies. An increasing trend in CO by 0.33 ppb yr-1 in the past decade at Ascension Island is attributed to the combined effects of South American/southern Africa burnings and the increases in CH4 …

Effects Of Stratospheric Ozone Recovery On Photochemistry And Ozone Air Quality In The Troposphere, H. Zhang, Shiliang Wu, Y. Huang, Y. Wang

Michigan Tech Publications, Part 1

There has been significant stratospheric ozone depletion since the late 1970s due to ozone-depleting substances (ODSs). With the implementation of the Montreal Protocol and its amendments and adjustments, stratospheric ozone is expected to recover towards its pre-1980 level in the coming decades. In this study, we examine the implications of stratospheric ozone recovery for the tropospheric chemistry and ozone air quality with a global chemical transport model (GEOS-Chem). With a full recovery of the stratospheric ozone, the projected increases in ozone column range from 1% over the low latitudes to more than 10% over the polar regions. The sensitivity factor …

Synthesis And Characterization Of High-Iron Alite-Calcium Sulfoaluminate-Ferrite Cements Produced From Industrial By-Products, Tristana Y. Duvallet, Youngmin Zhou, Thomas L. Robl, Rodney Andrews

Coal Combustion and Gasification Products Journal Archive

Ordinary Portland cement (OPC) and calcium sulfoaluminate cement (CSAC) are well-known and commonly used construction materials. The clinker phases mainly responsible for their strength development are C3S (alite) in OPC, which hydrates to form a calcium silicate gel phase; and C4A3S ´ (calcium sulfoaluminate) in CSAC, which hydrates to rapidly form ettringite. The purpose of this work was to produce high-iron alite-calcium sulfoaluminate-ferrite cements, by combining C4AF (ferrite), from 5% to 50% by weight, to the C3S and C4A3S ´ clinker phases. Producing this alite-calcium sulfoaluminate-ferrite cement would decrease the requirement of bauxite in the raw materials, which would consequently …

Performance Assessment Of Capture Zones Generated By Pv-Powered Pump And Treat Systems, Yovanna Cortes Di Lena

Doctoral Dissertations

"Pump and treat (P&T) is a technology that has been extensively used to remove and/or contain contaminated groundwater. Hydraulic containment of contaminants is accomplished by generating capture zones through pumping of groundwater. An appropriate delineation of capture zones is necessary to design an effective P&T system. P&T systems conventionally operate continuously to achieve steady-state capture zones, which require significant amounts of energy. The use of renewable energies to meet power demands of remedial systems may reduce a project's carbon dioxide emissions. The hydraulic effectiveness of a photovoltaic (PV) powered P&T system without energy storage was characterized using data collected at …

Experimental And Modelling Evaluation Of Slagging Behaviour Of German Lignite, Martin Kaiser, Alexander Ilyushechkin

Coal Combustion and Gasification Products Journal Archive

The behaviour of mineral matter is important for the characterisation of coal for use in entrained-flow gasification technologies. We investigated four behavioural characteristics—ash fusion temperatures (AFT), slag viscosity versus temperature profiles, temperatures of critical viscosity (TCV), and slag phase compositions—of Rhenish lignite coal ash using laboratory and modelling tools. Our modelling of AFT using coal ash composition provided a wide range of data, with only one (modified) model demonstrating agreement with experimental data. Experimental slag viscosity data were obtained over a temperature range from 1200uC to 1500uC. Where relevant, TCV was also measured. Comparison of these data to the calculated …

Fly Ash As A Potential Scrubber Of Acidic Wastes From The Phosphate Industries In Israel, Roy Nir Lieberman, Eli Lederman, Ithamar Pelly, Haim Cohen

Coal Combustion and Gasification Products Journal Archive

Fly ash (FA) is produced in Israeli utilities via bituminous coal combustion. It is used as a cement additive or in concrete production, and its economic value is low. The FA produced in Israel is very basic (defined as class F) owing to ambient air quality standards that impose low sulfur content in the imported coals. Because the lime content is high (in the South African coal, ,10 wt%), it is a good potential chemical scrubber to acidic wastes. The phosphate industry in Israel produces mainly phosphate fertilizers and water-treatment products as well as phosphoric acid. The production methods rely …

Geochemistry And Mineralogy Of Coal-Fired Circulating Fluidized Bed Combustion Fly Ashes, Luis F.O. Silva, Marcos L.S. Oliveira, Rubens M. Kautzmann, Claudete G. Ramos, Maria Izquierdo, Shifeng Dai, Jennifer Wilcox, Jeremy Hoffman, James C. Hower

Coal Combustion and Gasification Products Journal Archive

The fuel, bed ash, and fly ash were sampled from a circulating fluidized bed combustion (CFBC) unit at two times. The first sampling was a high-sulfur (S) coal-only run, and the second sampling coincided with an experimental burn of up to 10% switchgrass (Panicum virgatum) pressed pellets mixed with a high-S coal. The latter blend had a higher moisture content and a lower heating value than the coal-only fuel. Given the time between the samplings and the special needs for the experimental run, unavoidable changes in the coal and limestone complicate comparisons of the bed ash and fly ash chemistry …