Electrical and Electronics Commons^™

Design Of A Sigma-Delta Adc In 65nm Cmos Process, Michael Lee Thompson Iii

Electrical Engineering Undergraduate Honors Theses

Analog and digital signals both play a vital role in electrical engineering and the technology of today. As the role of electrical and computer engineers becomes more deeply involved in the development of new technology, an understanding of how these signals are utilized, and what they represent, is a necessity. Due to the inherent limitations involved with analog signals, there is a need for these signals to be accurately and efficiently converted to digital signals for processing. The job of the analog-to-digital converter, or ADC, is to receive this analog input signal (voltage or current) and create a digital representation …

Universal Short-Circuit And Open-Circuit Fault Detection For An Inverter, Buck Brown

All Theses

Short-circuit and open-circuit faults of an inverter’s power device often lead to catastrophic failure of the entire system if not detected and acted upon within a few microseconds, particularly for emerging wide bandgap (WGB) power semiconductors. While a significant amount of research has been done on the fast and accurate protection and detection of short-circuit faults, there has been less success corresponding to the research on open-circuit faults. Common downfalls include protection and detection that are too application-specific, take longer than a couple of microseconds, and are not cost-efficient. This study proposes a new open-circuit fault protection and detection system …

Control And Design Of A Passive Solar Lumber Drying Kiln, Peter Chardavoyne

Honors Scholar Theses

The passive solar lumber drying kiln design, developed by EE Senior Design Team 2317 is presented, tested, and discussed. The design incorporates solar power and a custom control system to dry 12’ lumber boards inside a shipping container much faster than air-drying methods, which can take up to a year for thorough drying, though this can be extended due to the unpredictability of weather events and conditions. This work presents the design as in the final report provided by the team, but provides a more detailed explanation and analysis of the microcontroller system, testing methods and outcomes, alternate solutions and …

Multiple Output Power Supply Using Toroidal Transformers For Medium Voltage Active Gate Drivers, Samhitha Venkata Machireddy

Graduate Theses and Dissertations

When operating in high power applications, power devices dissipate tens or hundreds of watts of power in the form of heat. The ability of the power devices to withstand power and dissipation of heat across the power devices becomes a prominent requirement in designing the power converter. This challenge demands a power converter design to be more effective and consistent which factors in size, cost, weight, power density and reliability. This study aims to propose a gate driver isolated power supply design that can be used in medium voltage applications (e.g., up to 10 kV) while respecting the principle of …

Stream Processor Development Using Multi-Threshold Null Convention Logic Asynchronous Design Methodology, Wassim Khalil

Graduate Theses and Dissertations

Decreasing transistor feature size has led to an increase in the number of transistors in integrated circuits (IC), allowing for the implementation of more complex logic. However, such logic also requires more complex clock tree synthesis (CTS) to avoid timing violations as the clock must reach many more gates over larger areas. Thus, timing analysis requires significantly more computing power and designer involvement than in the past. For these reasons, IC designers have been pushed to nix conventional synchronous (SYNC) architecture and explore novel methodologies such as asynchronous, self-timed architecture. This dissertation evaluates the nominal active energy, voltage-scaled active energy, …

A Nonlinear-Model-Based High-Bandwidth Current Sensor Design For Switching Current Measurement Of Wide Bandgap Devices, Xia Du, Liyang Du, Yuxiang Chen, Yuqui Wei, Andrea Stratta, H. Alan Mantooth

Electrical Engineering Faculty Publications and Presentations

With the growing adoption of wide bandgap devices in power electronic applications, current sensor design for switching current measurement has become more important. The demands for high accuracy, high bandwidth, low cost, compact size, and galvanic isolation pose significant design challenges. The conventional modeling approach for bandwidth analysis of current transformer sensors assumes that the magnetizing inductance remains constant, which does not always hold true in high-frequency operations. This can result in inaccurate bandwidth estimation and affect the overall performance of the current sensor. To address this limitation, this paper provides a comprehensive analysis of nonlinear modeling and bandwidth, considering …

Photovoltaics, Batteries, And Silicon Carbide Power Electronics Based Infrastructure For Sustainable Power Networks, Prahaladh Paniyil

All Dissertations

The consequences of climate change have emphasized the need for a power network that is centered around clean, green, and renewable sources of energy. Currently, Photovoltaics (PV) and wind turbines are the only two modes of technology that can convert renewable energy of the sun and wind respectively into large-scale power for the electricity network. This dissertation aims at providing a novel solution to implement these sources of power (majorly PV) coupled with Lithium-ion battery storage in an efficient and sustainable approach. Such a power network can enable efficiency, reliability, low-cost, and sustainability with minimum impact to the environment.

The …

Addressing The Challenged Of Dcop Based Decision-Making Algorithms In Modern Power Systems, Luis Daniel Ramirez Burgueno

Open Access Theses & Dissertations

Natural disasters have been determined as the leading cause of power outages, causing not only huge economic losses, but also the interruption of crucial welfare activities and the arise of security concerns. Because of the later, decision-making considering grid modernization, power system economics, and system resiliency has been a crucial theme in power systemsâ?? research. The need to better withstand catastrophic events and reducing the dependency of bulky generating units has propelled the development and better management of behind-the-meter generation or distributed energy resources (DERs). DERs can assist in the grid in different manners, not only by meeting energy demand …

Cyber-Physical Production Systems And Their Practical Integration And Application With Simio Software, Jose Carlos Garcia Marquez Basaldua

Open Access Theses & Dissertations

Industry 4.0 comprises a diverse array of technologies and components that are revolutionizing the manufacturing industry, from Digital Twins, Cyber-Physical Systems and Augmented Reality. The elements that englobe Industry 4.0 vary from framework to framework. Nevertheless, there are similarities in the available literature on what constitutes Industry 4.0. Some of the most critical components specified by the available literature include Digital Twins and Cyber-Physical Systems. A Factory Digital Twin is a virtual representation of a production system that can mimic the behavior of the physical asset. Moreover, a digital twin must have synchronization with its physical twin (i.e., production floor), …

The Study Of Corrosion On Additive-Manufactured Metals., Braydan Daniels

Electronic Theses and Dissertations

The purpose of this study was to investigate and compare the corrosion mechanisms between wrought and additive-manufactured (3D-printed) copper and stainless steel. The experimental procedure consisted of measuring the open circuit potential, electrochemical impedance spectroscopy, linear sweep voltammetry, Tafel analysis, surface topology, and scanning electron microscopy for each metal within salt water, tap water, sulfuric acid, and synthetic body fluid (excluding copper in synthetic body fluid).

Overall, printed stainless steel was more corrosion-resistant than wrought stainless steel in tap water and synthetic body fluid based on OCP, LSV, and surface topology results. Additionally, printed copper was more corrosion-resistant than wrought …

Effect On Focusing Fields By Ferromagnetic Cell Cores In Linear Induction Accelerators, Cooper Guillaume

Senior Honors Theses

In the Los Alamos National Laboratories DARHT facility, there are two perpendicular linear induction accelerators, LIAs. The LIAs’ solenoids produce magnetic fields which focus the electron beam. Simultaneously, the accelerating pulse creates a magnetic field. These two field intensities act upon a ferromagnetic material in the cells to enhance magnetic flux density. Due to the nonlinearity of the material, this flux density will reach a saturation point. In turn, the magnetic field intensity of the axial solenoidal magnetic field will be affected and slightly altered. The width of the electron beam will increase, causing a decrease in effectiveness. Through simulation, …

Design And Implementation Of High-Efficiency, Lightweight, System-Friendly Solid-State Circuit Breaker, Dehao Qin

All Dissertations

Direct current (DC) distribution system has shown potential over the alternative current (AC) distribution system in some application scenarios, e.g., electrified transportation, renewable energy, data center, etc. Because of the fast response speed, DC solid-state circuit breaker (SSCB) becomes a promising technology for the future power electronics intensive DC energy system with fault-tolerant capability. First, a thorough literature survey is performed to review the DC-SSCB technology. The key components for DC-SSCB, including power semiconductors, topologies, energy absorption units, and fault detection circuits, are studied. It is observed that the prior studies mainly focus on the basic interruption capability of the …

Analysis Of An Isolated Bidirectional Ćuk Converter, Yeny Hau Chen

Graduate Theses and Dissertations

The objective of this thesis is to perform an analysis of the isolated bidirectional Ćuk dc-dc converter topology and demonstrate the advantages and operation of this configuration through simulations using MATLAB/SimulinkTM and measurements collected from a 1.5-kW prototype tested at the Engineering Research Center (ENRC) laboratory of the University of Arkansas. The idea of integrating an active-clamp snubber circuit on each side of the converter, proposed by Dr. Sudip Mazumder from the University of Illinois, Chicago, limits the additional voltage stresses on the components due to the energy from the transformer’s leakage inductance. This is studied in this thesis to …

Restorative Hand Therapy Exercise Using Iot-Based Flex Force Smart Glove, Yi Neng Chang, Mohamad Khairi Ishak, Khalid Ammar

Makara Journal of Technology

Stroke has long been a major health concern in Malaysia, with cerebrovascular disease accounting for one-third of all deaths. Patients who have had a stroke have varying degrees of movement impairment, which can be improved with physiotherapy. A smart glove system is proposed in this paper to measure and visualize patient finger flexes in real-time remotely and record these flexes for further analysis to monitor and assess patient physiotherapy sessions. The system is designed to help physiotherapists evaluate physiotherapy exercises of patients and provide detailed information regarding the rehabilitation process. This paper also includes performance analysis and data from physiotherapy …

Power Amplifier Based On Composite Injection-Voltaic Transistors, Nodira Batirdjanovna Alimova

Chemical Technology, Control and Management

The problem of high-current radio engineering devices is related to the fact that the use of high-power transistors and other semiconductor devices is limited by such a phenomenon as a secondary breakdown, in which there is a sharp decrease in the voltage on the device with simultaneous internal current lacing, and the device fails. To solve the problem of secondary breakdown, schemes have been proposed that operate stably at reverse voltage values 4-5 times higher than usual and at power dissipation 2-3 times higher than the maximum allowable power for an individual device. The problem is proposed to be solved …

The Magnetic Chain Mathematical Models Of A New Angular Displacement Converter With A Variable Active Area Of A Movable Core, Sultan Faizullayevich Аmirov, Ulugbek Shukhratovich Mamadaliyev, Islom Azim Ugli Karimov

Chemical Technology, Control and Management

The article develops mathematical models of the magnetic chain of new differential type angular displacement transformer converter with a variable active area of the movable core, in which the width of the movable ferromagnetic core is a function of the angular displacement of the converter. In this case, the magnetic chain of the converter, divided into three characteristic (before the mobile ferromagnetic core, ferromagnetic core and after the ferromagnetic core) sections, is considered as a magnetic chain with distributed parameters. It is established that when the magnetic resistance of the magnetic chain steel part is not taken into account, the …

Design And Development Of A Solar Module Health Monitoring Device, Elijah Madaris, Christopher Baden, Sandip Das

Symposium of Student Scholars

Solar power has emerged as a promising renewable clean energy source and installations of solar panels are increasing sharply year after year. Monitoring the power output and health of solar panels is critically important to ensure safe and reliable operation of a solar power plant throughout its operational lifetime. In this project, we have designed and built a low-cost electronic device that is capable of measuring the electrical parameters of a solar cell or module. The device consists of a microprocessor with integrated analog-to-digital converter, a supercapacitor bank, current sense amplifier, and electromechanical relays. The microprocessor performs data acquisition through …

Portable Diffuse Reflectance Spectroscopy For Non-Invasive And Quantitative Assessment Of The Parathyroid Glands Viability During Surgery, Mark Romine, Linh Luong, Alex Moazzen, Katie Cho, Paul Lee

Symposium of Student Scholars

Portable Diffuse Reflectance Spectroscopy for Non-invasive and Quantitative Assessment of the Parathyroid Glands Viability During Surgery

Mark Romine, Linh Luong, Alex Moazzen, Katie Cho and Paul Lee

The parathyroid glands (PTGs) are responsible for the regulation of calcium levels in the blood by secreting a parathyroid hormone. This parathyroid hormone then regulates the body’s absorption, storage, and secretion of calcium, which can directly affect the way muscles and nerves operate. PTGs are often at risk of damage, or accidental removal during thyroid surgeries, because it is challenging to identify PTGs and to determine their viability. Current methods of visual inspections …

Premium Single Phase Motor For Abb Group, Daniel Johnson, Sky Friar, Jesse Willer

ATU Scholars Symposium

ABB Group is in search of a next generation premium single phase motor. An integrated drive paired to a three phase motor will allow the company to take advantage of current three phase motor automation capacity while presenting the end user with a simple, ready to use motor operating off of single phase power. This project is the design of such an integrated drive.

The drive will accept 115/230 Vac, single phase supply power and send it through a full bridge rectifying, voltage doubling circuit. This circuit will rectify the alternating current to direct current and increase the voltage to …

Discriminating Wirelesshart Communication Devices Using Sub-Nyquist Stimulated Responses, Jeffrey D. Long, Michael A. Temple, Christopher M. Rondeau

Faculty Publications

Reliable detection of counterfeit electronic, electrical, and electromechanical devices within critical information and communications technology systems ensures that operational integrity and resiliency are maintained. Counterfeit detection extends the device’s service life that spans manufacture and pre-installation to removal and disposition activity. This is addressed here using Distinct Native Attribute (DNA) fingerprinting while considering the effects of sub-Nyquist sampling on DNA-based discrimination. The sub-Nyquist sampled signals were obtained using factor-of-205 decimation on Nyquist-compliant WirelessHART response signals. The DNA is extracted from actively stimulated responses of eight commercial WirelessHART adapters and metrics introduced to characterize classifier performance. Adverse effects of sub-Nyquist decimation …

Implementation Of Static Rfid Landmarks In Slam For Planogram Compliance, Brennan L. Drake

Honors College Theses

Autonomous robotic systems are becoming increasingly prevalent in everyday life and exhibit robust solutions in a wide range of applications. They face many obstacles with the foremost of which being SLAM, or Simultaneous Localization and Mapping, that encompasses both creation of the map of an unknown environment and localization of the robot in said environment. In this experiment, researchers propose the use of RFID tags in a semi-dynamic commercial environment to provide concrete landmarks for localization and mapping in pursuit of increased locational certainty. With this obtained, the ultimate goal of the research is to construct a robotics platform for …

Evaluation Of The Dynamic Vision Sensor’S Photoreceptor Circuit For Infrared Event-Based Sensing, Zinah M. Alsaad

Electrical and Computer Engineering ETDs

For space surveillance applications, neuromorphic imaging is being studied as it may perform sensing and tracking tasks with less power and downstream datalink demand. The read-out of the event-based camera is made to only be sensitive to changes in the signals it receives from the photodetector, which results in a datastream of events indicating where and when changes in illumination occur. This is in contrast to the conventional framing camera, which produces images by essentially counting the electrons produced by light incident on each pixel’s photodetector. These cameras are commercially available with siliconbased detectors for applications involving visible wavelengths. However, …

Creating A Power System For A Robot, Nolan Hays

Scholars Week

I will be describing the process of creating the power system for the robot that will be competing in the 2023 IEEE Hardware Competition.

Coordinated Location And Capacity Planning Of Fast Charging Stations For Electric Vehicles Using Multi Objective Approach, Asna Madathodika

Dissertations

With the growing concerns on the energy depletion and CO₂ emissions, electric vehicles (EVs) have marked a new paradigm in the transport sector. Installation of publicly accessible charging stations (CS), namely fast CSs are crucial for the large-scale deployment of EVs. However, randomly placing CSs without prior research affect EV owners, CS operators and grid operators. For instance, the location and size of charging stations affect the accessibility and convenience of EV users since users prefer charging stations that are easier to access without much traffic congestion in road networks. At the same time station should offer good service …

Capturing Maximum Photovoltaic Power With Machine Learning: Maximum Current Prediction, Mppt Methodology, And Adjustable Ml-Based Controller, Zahi Mohamed Mohamed

Dissertations

The primary aim of this doctoral thesis is to examine the potential application of machine learning (ML) in optimizing Maximum Power Point Tracking (MPPT) and devising a flexible ML-based controller for photovoltaic (PV) systems. The lack of MPPT mechanisms leads to fixed voltage and current points for PV modules, resulting in substantial power loss when environmental conditions vary. The limitations of conventional and enhanced MPPT methods, as well as finding an alternative controller to classical Proportional-Integral (PI) controllers, have spurred the search for substitute approaches to maximize PV power. To address these limitations, this thesis proposes using ensemble ML techniques, …

Pvpbc: Privacy- And Verifiability-Preserving E-Voting Based On Permissioned Blockchain, Muntadher Sallal, Ruairí De Fréin, Ali Malik

Articles

Privacy and verifiability are crucial security requirements in e-voting systems and combining them is considered to be a challenge given that they seem to be contradictory. On one hand, privacy means that cast votes cannot be traced to the corresponding voters. On the other hand, linkability of voters and their votes is a requirement of verifiability which has the consequence that a voter is able to check their vote in the election result. These two contradictory features can be addressed by adopting privacy-preserving cryptographic primitives, which at the same time as achieving privacy, achieve verifiability. Many end-to-end schemes that support …

Unsupervised Learning Algorithm For Noise Suppression And Speech Enhancement Applications, Abdullah Zaini Alsheibi

Electronic Theses and Dissertations

Smart and intelligent devices are being integrated more and more into day-to-day life to perform a multitude of tasks. These tasks include, but are not limited to, job automation, smart utility management, etc., with the aim to improve quality of life and to make normal day-to-day chores as effortless as possible. These smart devices may or may not be connected to the internet to accomplish tasks. Additionally, human-machine interaction with such devices may be touch-screen based or based on voice commands. To understand and act upon received voice commands, these devices require to enhance and distinguish the (clean) speech signal …

Assessing Hardware Security Threats Posed By Hardware Trojans In Power Electronics, Quinn Kinzie

All Theses

This study investigates the threat of hardware Trojans (HTs) in power electronics applications, a rising concern due to the growing demand for cost-effective embedded solutions in power systems. With the supply chain for electronic hardware devices expanding globally, particularly to low-cost foundries in foreign locations, there is an increasing risk of HT attacks. While there has been extensive research on HTs in computer applications, little consideration has been given to their threat in power electronics. This study demonstrates the effectiveness of a power electronics HT by implementing a novel HT design into a gate drive circuit. Additionally, the research proposes …

Design Of A Miniaturized Cubesat Tt&C Patch Antenna, Thomas A. Butterick

Theses and Dissertations

This effort explored the design of miniaturized rectangular microstrip patch antennas for application as a telemetry, tracking, and control (TT&C) on a CubeSat. The motivation for this research was the Grissom-P CubeSat mission planned by AFIT. The TT&C antenna selected for the mission exceeded the allotted size by over a factor of two. The studies performed included analyses of simply reducing aperture size, altering substrate permittivity, and layered approaches to antenna miniaturization. The primary approach to miniaturization was based on a virtually shorted patch antenna. Other approaches included an edge-shorted, slotted patch and the use of corner truncations for improved …

Comparison Of Federated Kalman Filter And Autonomous Resilient Management Of All-Source Sensors (Armas) Framework For Fault Detection And Exclusion, Flavio Fernandes

Theses and Dissertations

In recent times, there is a great demand for resilient and robust PNT solutions. Current navigation systems rely heavily on GNSS to provide this solution. This dependence is a major concern and therefore it is prudent to use additional aids to provide the best solution possible. However, traditional methods to address this need require a nontrivial number of Kalman filters to maintain a fault-free solution. The federated filter approach provides an attractive alternative to the current solutions. In this thesis, we examine the use of the federated filter design to address this need in today’s integrated navigation systems. We compared …