Electrical and Electronics Commons^™

Modeling Of Vacuum Microelectronic Lateral And Vertical Devices, Qiong Gui

Theses

Vertical and lateral configurations of the vacuum microelectronic device have been modeled using the simulation tools. Both cone and ridge cathode structures are used. Simulation results are compared with experimental data where available. These device structures include cathode, extraction grid, anode, and deflectors. The electric field at the tip of the cathode has been calculated for tip radius as small as 0.1nm. The model used takes into account the effect of potential on all electrodes on the E-field at the cathode tip. Also the effect of cathode geometry on the E-field is detailed.

Static characteristics are based on a new …

A Cmos Logic Circuit To Reduce Substrate Current/Hot Carrier Effect, Tejinder K. Jaswal

Theses

A new C-MOS NAND and CMOS full adder logic circuits which reduces hot carrier problems are discussed. The application of new circuit lowers the channel electric field in N-MOSFET during switching transient and leads to suppression of the N-MOSFET substrate current. The simulation results shows that about 3.99 and 3.75 times smaller peak substrate current are obtained in C-MOS NAND and adder with new circuit compared to the conventional logic circuits. These logic circuits also gives better noise and shows shorter rise and fall times. The new concept provides highly reliable logic circuits without any change of device structure or …

A Comparative Study Of Image Coding Techniques : Filter Banks Vs. Discrete Cosine Transform, Hosam Fawzi Mutlag

Theses

Subband coding of still image frames using Binomial PR-QMF has been presented in this thesis. Simulation results have shown that the performance of subband coding using a low complexity coder is practically the same as the performance of the industry standard (8 x 8) DCT based image coder.

A low bit rate adaptive video coding technique is also introduced in this thesis. The redundancy within adjacent video frames is exploited by motion compensated interframe prediction. The Motion Compensated Frame Difference (MCFD) signals are filtered by employing Binomial PR-QMF structure into four subbands. Then, the subbands are quantized using an efficient …

Androx Implementation Of Nonlinear Filter, Keh-Chao Chu

Theses

Nonlinear filters, such as morphological operations, play an important role in image processing. Several software implementations of nonlinear filters are presented in this thesis. There may exist more than one method to implement a specific operation. The methods used in this thesis are chosen to be most suited for the machine used according to its structure. These most suited methods are also generally best for software implementations on other machines as well. The machine used here is the Androx image computing workstation.

Direct Recovering Of Composite Surface Using Uoff, Zhesheng Huang

Theses

The research work reported in the thesis is motivated by the problem raised in the computer vision area. It utilizes direct method to recover surface structure of objects in 3-D space from a pair of stereo images. The direct method, compared with optical flow-based approach and feature-based approach, is robust and computationally efficient. However it can only recover planar surface structure so far. A new approach to recover structure from a pair of stereo images based on unified optical flow field (UOFF) is developed recently. It can recover curved surface structure.

In this thesis, the problem of recovering surface structure …

A New Approach To Motion Analysis From A Sequence Of Stereo Images, Lin Zhou

Theses

A new approach to motion analysis from a sequence of stereo images is presented in this thesis. Based on a four-frame model, a new concept of unified optical flow field has been developed recently [3]. It is a generalization of the optical flow in stereo imagery. A set of fundamental equations is established to characterize the unified optical flow field. Another set of equations is then derived from which 3-D motion can be reconstructed via the use of the field quantities of the unified optical flow field. In this thesis, the implementation of the approach is conducted. The simulation and …

Electroretinogram Modeling : Parameter Identification And Intensity-Response Function Fits, Juan J. Castro

Theses

Electroretinography testing provides many useful techniques for clinical diagnosis of the visual system. However, the interpretation of the electroretinogram data involves a great amount of subjectivity. The use of mathematical models and parameter estimation techniques to fit the electroretinogram data supply a non-subjective and more standard way for analysis of the electroretinogram data. Mathematical models provide a way of summarizing the information enclosed in the raw electroretinogram response into a small set of parameters that define the response.

This thesis presents a mathematical model for the electroretinogram response due to light stimuli. It also provides a non-subjective method for obtaining …

Monte Carlo Simulation Of Millimeter-Wave Gunn Effect Oscillators, Ramani Vaidyanathan

Electrical & Computer Engineering Theses & Dissertations

Monte Carlo simulations have been carried out to investigate the performance of microwave Gunn oscillators. Three separate aspects of the simulation problem have been comprehensively addressed in this work. First, the presence of an external circuit has been self-consistently incorporated into the calculations. The inclusion of the external circuit facilitates a study of the circuit controlled regime, and correctly models effects arising from the time dependent boundary conditions. Secondly, microscopic details of the electronic relaxation mechanisms which ultimately control the frequency response limits, have been taken into account through an iterative Monte Carlo-Poisson scheme. This procedure overcomes a potential shortcoming …

The Breakdown Mechanism Of Hollow Cathode Discharge, Mai Tuyet Ngo

Electrical & Computer Engineering Theses & Dissertations

In a low pressure discharge, if the cathode incorporates a cylindrical or slit shaped hole, the discharge current can be several orders of magnitude higher than in one with plane parallel electrodes under the same pressure and voltage conditions. In this work hollow cathode discharges in Helium under the influence of variable parameters such as gas pressure, applied voltage, electrode gap spacing, external magnetic field, etc., are investigated by means of electrical and optical diagnostic techniques.

The results indicate that a hollow cathode discharge develops in two stages. The initial breakdown occurs along the longest straight path of the system, …

A Navigation Reference System (Nrs) Using Global Positioning System (Gps) Aiding, Richard D. Stacey

Theses and Dissertations

To quantify the performance abilities of existing or proposed navigation systems, the U.S. Air Force has for the last several years compared the performance of the system under test to the performance of a baseline navigation system known as the Completely Integrated Reference Instrumentation System (CIRIS). CIRIS obtains a highly accurate navigation solution by combining the output from three major subsystems: inertial navigation system (INS) information, barometric altitude information, and range and range-rate data from ground transponders which have been precisely surveyed. Although the navigation solution produced by CIRIS is highly accurate, it will soon be inadequate as the standard …

A Fully Coupled, Automated Formation Control System For Dissimilar Aircraft In Maneuvering Formation Flight, Paul R. Rohs

Theses and Dissertations

This study developed a fully automated formulation control system, capable of controlling a number of like or dissimilar aircraft in maneuvering formation flight. C-130 fixed wing aircraft and H-53 helicopters were modelled in various formulations and simulated through a mix of maneuvers. External formation guidance was assumed as a single data burst of nominal function guidance commands and separation distances for each wing aircraft in the formation. No communication was assumed between formation aircraft. Wing aircraft track lead aircraft maneuvering with an ideal on-board sensor, maneuvering to maintain relative position. It was determined that lead aircraft inputs must be attenuated …

Multiresolution Techniques : Laplacian Pyramid Coding And Its Comparison With Subband Coding, Danmei Chang

Theses

The multiresolution pyramid and related structures have been developed as intermediate representations between the purely frequency domain and purely spatial domain. In this thesis. we discuss two important pyramid structures which are often used in multiresolution representation: Laplacian pyramid and subband coding.

Laplacian pyramid. a typical pyramid structure, is studied in detail. By means of software implementation. we obtain a comprehensive understanding of its features and applications in image representation and data compression. Several modifications of pyramid structure are used to compress the data dynamic range, reduce the computational complexity and improve performance. Performance of the conventional Laplacian pyramid and …

A Machine Vision System With Remote Host, Chieyeon Jason Chen

Theses

The modem plays an important role in data communication using the Public Swiched Telephone Network. In this thesis, the modem function is merged into a low cost machine vision system based on the Motorola 68HC11. Evalation Board The system comprises the intelligent machine vision con- troller and a remotely located host computer, such as an IBM-PC. It, supports extra long distance communication capability so that the controller and the host can be anywhere in the world where then is a telephone line. Because of the limit of a 2100 bps modem, soft ware data compression is implemented here to save …

Artificial Dielectric Polymeric Optical Waveguides, Peng Chen

Theses

Wave propagation in artificial dielectric polymeric optical thin film waveguides is studied. These artificial dielectric films are made of multiple layers either metallic or semiconductor clusters in polymeric matrix. The waveguides are fabricated using the plasma polymerization and vacuumm evaporation deposition method. By analyzing results of these kinds of structures, some important conclusions can be obtained. The artificial dielectric layer in the waveguide center effectively changes the modal distribution in the waveguides. In the case of semiconductor layer, an all optical switch may be realized.

A Multimode Index Detecting Sensor For Use In Plastic Concrete, Qiyu Chen

Theses

This thesis describes a microcomputer-based measuring system using a laser diode source, a fiber optic sensor and a microcomputer DMA interface to test and analyze the entrained percentage of air in concrete.

The principle of refraction and reflection of light in optical fibers is applied to detection of air bubbles. Reflected light intensity signals are detected and transferred through a DMA interface to a laptop computer. Analysis of reflected light intensity produces a measurement of the air content of fresh concrete. Accuracy of the system is evaluated through extensive laboratory and field trials.

Ct Fan Beam Reconstruction With A Non-Stationary Axis-Of-Rotation, Joseph A. Concepcion

Theses

One important aspect for reconstructing an image using Computed Tomography (CT) is that the axis-of-rotation must pivot at the same point on the reconstruction plane as the x-ray source and CT scanner assembly rotates around the imaged object. This pivot point is used as a reference point for backprojecting pixel values to their proper coordinates. Therefore, reconstructing an image with a non-stationary axis-of-rotation would backproject pixel values to wrong coordinate points, since the reference point is non-stationary for every projection angle.

A convolution filtered backprojection algorithm has been derived for correcting images that were acquired with a non-stationary axis-of-rotation using …

Tri-Color Led Display System Using Microcontroller, Costakis A. Constantinou

Theses

A seven-by-forty-eight tricolor LED display panel is designed and built around the 68HC11 MCU.

Four bilateral switching transistors (4066) are used in a Wien bridge configuration to drive each tri-color LED. With this circuitry one is able to drive the tricolor LED symmetrically. An alternative design that uses only two switching transistors is also offered.

A software program was developed to output on the display scrolling and fixed messages. Each message could be displayed in a different color (Red, Green and Yellow) and at a different speed (Slow, Fast, and Medium). The program also includes an editor with insertion and …

Novel Way Of Sub-Carrier Coherent Detection And Clock Recovery In Fiber-Optic Communications, Narayan Gehlot

Theses

We experimentally demonstrate a novel concept for recovery of a Sub-Carrier and Timing Clock in fiber-optic communication systems using a Wavelength Division Multiplexing technique. The idea is to send a low radio frequency (RF) as a reference pilot from the transmitter to the receiver on a separate laser using the principle of Wavelength Division Multiplexing (WDM). This low frequency signal is taken to be a subharmonic of the subcarrier used to carry information and intensity modulate another laser. Such approach will be expected to generate at the receiver a local oscillator in high coherence with the subcarrier.

We show that …

Uniformity Correction For Infrared Ir-Ccd Camera, Chien-Ming Leng

Theses

This thesis describes the results of a study of three types of uniformity correction schemes for an infrared camera. More specifically, a Datacube Image System was used to simulate the three uniformity correction schemes for a 320x244-element IR-CCD TV camera with PtSi Schottky-barrier detectors. The three uniformity correction schemes are: one-point uniformity correction with single background, one-point uniformity correction with multibackground and two-point uniformity correction. Datacube programs were developed for the three above uniformity correction schemes and some experimental results were obtained.

On The Estimation Of New Life Model Of Transformer Insulation Material Under Combined Electrical And Thermal Stress, Chiming Lin

Theses

Results of combined electrical and thermal aging and only thermal aging studies conducted on a 'fish' paper insulation material are presented in this thesis.

The model for aging has been proposed which is essentially the Arrhenius equation with a weighted factor {exp -cg/kT1 to describe the enhanced reaction rate process under combined thermal and electrical stress. A procedure has been described for evaluation of parameters of this new model.

It is seen that life estimates obtained with this model are close enough to the experimental results.

In addition, reliability data were also generated on the same material using electrical noise. …

Hot : A Timing Optimizer For Hierarchical Vlsi Circuits Using The Charge Conservation Delay Model, Yumei Quan

Theses

The primary benefits of VLSI chips are their high speed, small area, and lower power. These performance attributes are dependent on the quality of chip design. As a result, performance can be optimized by proper design decisions. One of the decisions in chip design is the selection of gate delays and/or transistor sizes (channel width of an MOS transistor).

To optimize the performance of VLSI chips, transistor delay models and optimization algorithms are very important since accurate analytical models for signal delay are essential to replace expensive device level simulation and the high efficient algorithms assist designers in developing high …

Design, Fabrication, And Testing Of Temperature Compensated Magfet, Dilip K. Sampath

Theses

A simple model based on dc behaviour of MOS transistors operating in weak inversion is derived on the basis of previous publications. The bipolar like source to drain transfer characteristics of MOS transistor in weak inversion was used to implement a voltage source that is proportional to absolute temperature (PTAT); a cell that can be stacked to obtain the desired voltage. A CMOS temperature compensated current reference is implemented using PTAT cell with MOSFET as current defining element. A CMOS magnetic field sensor has been developed. The sensitivity of sensor is dependant on the bias current; incorporation of temperature independent …

An Efficient Annealing Algorithm For Global Optimization In Boltzmann Machines, Rajendra Sarasakrishna

Theses

This thesis proposes a new annealing algorithm for Boltzmann Machines. This algorithm uses an Exponential Formula for temperature scheduling that produces remarkably better solutions for global optimization. The superiority of the new algorithm is shown by computer simulations of several examples on Boltzmann Machine and its variants. This is also shown to have better properties than algorithms like Generalized Simulated Annealing which possess somewhat similar dynamics.

Comparative Study Of Prediction Gain Based On Neural Network Architecture, Prashant M. Shah

Theses

This thesis describes the Neural Network approach to design predictor using Delta and Generalized Delta Rule. The predictor is designed by supervised training based on the typical sequence of pixel values. Neural Network is used to find the coefficients of the predictor. Both 1-D and 2-D scheme of the pixels as well as linear and non-linear correlations are used to find the coefficients by training. Different combinations of pixels are used to find the "best" combination among the order of the predictor.

Efficient Multiprocessor Scheduling By Mean Field Theory Neural Networks, Pei-Ken Yi

Theses

In this thesis, we develop an optimization method based on Mean Field Theory (MFT) Neural Networks to solve the Task Scheduling problem. The MFT algorithm combines characteristics of the Simulated Annealing (SA) algorithm and the Hopfield neural network. MFT exhibits rapid convergence and at the same time it preserves the solution quality afforded by SA. Since MFT has been successfully used to solve the Traveling Salesman Problem (TSP), a new modification to MFT is also presented which supports Task Scheduling problem. The temperature behavior of MFT during Task Scheduling is approximately analyzed and shown to possess a critical temperature (71,) …

Integrated Digital Speech System With Pc, Zhen Zhu

Theses

A PC-based real-time digital speech processing system is designed. Speech synthesis, analysis, storage and retrieval are implemented in the system with intelligent telephone functions. Speech data are stored on floppy disk and easy to retrieve. Though floppy disk is slow in speed, real-time processing is achieved with low bit rate coding. The computer gets speech data from a digital speech processing unit or send data to it through a synchronous seiial communication port. The analog input of digital speech processing unit can be selected from the telephone line or the microphone, and output of the digital speech processing unit can …

Decomposing Non-Product Form Queueing Lattices Through Autorouting With A* Algorithm, Chun-Chang Yu

Theses

Direct solution techniques are expensive for the state transition lattice of a class of non-product form queuing modes. In this thesis, Autorouting with A* algorithm is adapted to decompose it as solvable subsets which can be solved sequentially and independently. Autorouting with A* algorithm is heuristics in problem solving. It also is one of a class of global optimization problems that are difficult to solve. Some queuing modes of type A will be decomposed in this thesis through Autorouting with A* algorithm.

N-Cross Coupled Phase Locked Loops, Joseph C. Aboukhalil

Theses

Interference cancelation has been mainly performed using arrays, in an important issue in communication both array and spatial cancelation and time domain approach were used. In array applications, depth of cancelation may dependent on the interferences to background power ratio and their spatial distributions. Also, array cancelers are inadequate when the signals are less than an array beamwidth apart. The latter was dealt with using supperesolution and eigenanalysis methods. Different time domain methods were used in the past. Among them what is termed Cross-Coupled PEL. It is an arrangement of two PLL each one is locked on and tracking one …

Fault Tolerant Clos Network, Preet Mohan S. Ahluwalia

Theses

Multistage interconnection networks, or MINs, provide paths between functional modules in multiprocessor systems. The MINs are usually segmented into several stages. Each stage connects inputs to appropriate links of the next stage so that the cumulative effect of all the stages satisfies input-output connection requirements.

This thesis deals with a fault tolerant Clos network. The fault tolerance technique involves addition of extra switches per stage to compensate for any switch failure The reliability analysis of both ordinary and fault tolerant Clos networks is presented. The optimal number of extra switches required to get the best reliability results has been analyzed.

Direct Schottky Injection Image Sensors, Subramanyam V. Ayyagari

Theses

This thesis describes the analysis and simulations of Direct Schottky Injection (DSI) imagers which have 100% fill factor. Frame transfer (FT) and interline transfer (IT) DSI imager structures have been investigated. Theoretical Poisson solution for the PT and P-NP FT-DSI structures is presented, which closely agrees with simulation results. Simulation for frame transfer FT-DSI imagers has been done in SUPREM III since 1-D effects are more dominant. Single carrier transit time for both the structures were estimated from the electric fields.

Simulations of IT-DSI structures was done using PISCES llb, to get the local electric fields, which define the directionality …