Structural Engineering Commons^™

The Effect Of Enzymatic Hydrolysis On The Properties Of Protein Hydrolysate From Paddy Mushroom, Niken Widya Palupi, Wiwik Siti Windrati, Tamtarini Tamtarini

Makara Journal of Technology

Protein hydrolysate was prepared from Paddy (Volvariella volvaceae) mushroom. Hydrolysis uses commercially protease available Protamex ™ with enzyme concentration of 0.1% (w/w). Hydrolysis was performed at three different temperatures (room temperature, 40 °C, and 50 °C) with different incubation periods (60, 90, and 120 minutes). Enzyme inactivation was done in 90 °C for 3 minutes. Yield and degree of hydrolysis ranged from 94.76% to 99.55% and 19.06% to 24.59%. Protein solubility was about 89–11,8%. The longer time of hydrolysis, the darker the color of protein hydrolysate. Protein hydrolysate which has hydrolysis at 50 °C for 120 minutes has the highest …

Effect Of Diafiltration On Preparation Of Fermented Mung Beans Concentrate As Probiotic Savory Flavor Through Ultrafiltration Membrane, Aspiyanto Aspiyanto, Agustine Susilowati

Makara Journal of Technology

Diafiltration by means of the ultrafiltration system of probiotic fermented Mung beans (Phaseolus radiatus L.) concentrate has been performed to reduce or eliminate salts and smaller impurities than the nominal cut-off of the membrane of 20,000 nominal weight cut-off (NWCO). These processes have been conducted as an attempt in order to get a probiotic product with organoleptic acceptability, composition, and the optimal total lactic acid bacteria (LAB) counts because the presence of salts will affect on the viability of LAB and the cell lysis of LAB and limit its utility in food products. Concentrate of probiotic mung beans was prepared …

High Pressure Adsorption Isotherm Of Co2 On Activated Carbon Using Volumetric Method, Awaludin Martin, Bambang Suryawan, Muhammad Idrus Alhamid, Nasruddin Nasruddin

Makara Journal of Technology

High Pressure Adsorption Isotherm of CO2 on Activated Carbon using Volumetric Method. Adsorption system is ones of the most effective methods for CO2 separating with other substances that produced from the burning of fossil fuels. In the design for that application, beside of characteristics of porous material (adsorbent) data, CO2 adsorption data on the adsorbent (kinetic and thermodynamic) are also needed. The aim of this research is resulting isothermal adsorption data at pressures up to 3.5 MPa by indirect methods (volumetric method) at isothermal temperature of 300, 308, 318 and 338 K. Adsorbent that used in this research is activated …

Concept Design And Testing Of Multi-Nozzle Water Mist Fire Suppression System, Danardono A. Sumarsono, Yulianto S. Nugroho, Mariance Mariance, I Gede Wahyu W. Ariasa

Makara Journal of Technology

In this work a flexible design of multi-nozzle arrangement of water mist fire suppression system was studied. The source of fire was a 65 mm diameter cooking oil fire. An investigation on the impact of nozzle arrangement on the temperature profile of fires was conducted. The occurance of oil splash due to the application of water mist was also studied. The water mist systems developed in the present work can effectively extinguish cooking oil fires and prevented them from re-ignition. The spray angle, discharge pressure, and water flow rate were important factors to determine the effectiveness of water mist in …

The Stability Characteristics Of Sandbag Submerged Breakwater, Ferry Fatnanta, Widi Agoes Pratikto, Haryo Dwito Armono, Wahyudi Citrosiswoyo

Makara Journal of Technology

The Stability Characteristics of Sandbag Submerged Breakwater. Breakwater is one of coastal structures to overcome problems of abrasion. Due to difficulties in obtaining rock material at the coastal area. The using of sandbags as a breakwater provides advantages in utilizing local materials. A Sandbag has a smooth surface, so the internal shear forces are relatively small. According to these phenomena, the research for parameters that are expected to affect the stability of the sand bags. These parameters are a slope, shape and formation of sand bags. This experimental research conducted in two dimensional physical model and took place on the …

Static Hand Gesture Recognition Of Indonesian Sign Language System Based On Backpropagation Neural Networks, Farida Asriani, Hesti Susilawati

Makara Journal of Technology

Static Hand Gesture Recognition of Indonesian Sign Language System Based on Backpropagation Neural Networks. The main objective of this research is to perform pattern recognition of static hand gesture in Indonesian sign language. Basically, pattern recognition of static hand gesture in the form of image had three phases include: 1) segmentation of the image that will be recognizable form of the hands and face, 2) feature extraction and 3) pattern classification. In this research, we used images data of 15 classes of words static. Segmentation is performed using HSV with a threshold filter based on skin color. Feature extraction performed …

Dye Sensitized Solar Cell With Conventionally Annealed And Post-Hydrothermally Treated Nanocrystalline Semiconductor Oxide Tio2 Derived From Sol-Gel Process, Akhmad Herman Yuwono, Badrul Munir, Alfian Ferdiansyah, Arif Rahman, Wulandari Handini

Makara Journal of Technology

Dye-sensitized solar cell (DSSC) is one of the very promising alternative renewable energy sources to anticipate the declination in the fossil fuel reserves in the next few decades and to make use of the abundance of intensive sunlight energy in tropical countries like Indonesia. In the present study, TiO2 nanoparticles of different nanocrystallinity was synthesized via sol−gel process with various water to inorganic precursor ratio (Rw) of 0.85, 2.00 and 3.50 upon sol preparation, followed with subsequent drying, conventional annealing and post-hydrothermal treatments. The resulting nanoparticles were integrated into the DSSC prototype and sensitized with an organic dye made of …

Immobilization Of Saccharomyces Cerevisiae In Rice Hulls For Ethanol Production, Edita Martini, Dian Andriani, Sriramulu Gobikrishnan, Kyeong Eop Kang, Surn-Teh Bark, Changshin Sunwoo, Bambang Prasetya, Don-Hee Park

Makara Journal of Technology

The whole cell immobilization in ethanol fermentation can be done by using natural carriers or through synthetic carriers. All of these methods have the same purpose of retaining high cell concentrations within a certain defined region of space which leads to higher ethanol productivity. Lignocellulosic plant substance represents one of highly potential sources in ethanol production. Some studies have found that cellulosic substances substances can also be used as a natural carrier in cell immobilization by re-circulating pre-culture medium into a reactor. In this experiment, rice hulls without any treatment were used to immobilize Saccharomyces cerevisiae through semi solid state …

Wimax Implementation As Existing Hotspot Network Backhaul In Jakarta, Djamhari Sirat, Muhamad Asvial, Luther B. Marpaung

Makara Journal of Technology

WiMAX Implementation as Existing Hotspot Network Backhaul in Jakarta The development of Broadband Wireless Access (BWA), such as WiMAX, as a global standard for data transmission media has been used by high speed internet access provider. WiMAX application which supported by capabilities of interoperability, flexibility and commercial aspect make the internet services become more efficient, cheaper and easier to the customer. This phenomenon should be responded by ISPs. Based on technical and financial aspect in deciding the implementation of Wireless Network with WiMAX technology as a substitute, this research will observe and analyze the projection of WiMAX technology implementation as …

Plant Growth Modeling Using L-System Approach And Its Visualization, Atris Suyantohadi, Alfiyan Alfiyan, Mochamad Hariadi, Mauridhi Hery Purnomo

Makara Journal of Technology

The visualization of plant growth modeling using computer simulation has rarely been conducted with Lindenmayer System (L-System) approach. L-System generally has been used as framework for improving and designing realistic modeling on plant growth. It is one kind of tools for representing plant growth based on grammar sintax and mathematic formulation. This research aimed to design modeling and visualizing plant growth structure generated using L-System. The environment on modeling design used three dimension graphic on standart OpenGL format. The visualization on system design has been developed by some of L-System grammar, and the output graphic on three dimension reflected on …

Remote Sensing And Geographical Information System To Identify Drought Potency, Puguh Dwi Raharjo

Makara Journal of Technology

Remote Sensing and Geographical Information System to Identify Drought Potency. Kebumen regency was drought in year 2008, community clean water shortages and irrigation water following a decline in water resources. The use of remote sensing data and GIS can be used to identify the potential for drought-prone areas. Transformation of Landsat TM satellite imagery to obtain the brightness index, wetness index and vegetation index used to determine surface conditions in relation to drought. Brightness index and wetness index derived from the tasseled cap modifications, while the vegetation index derived from normalized difference vegetation index (NDVI) values. Other parameters such as …

Separation Study Of Titanomagnetite Fe3-Xtixo4 From Natural Sand At Indramayu, West Java, Sunaryo Sunaryo, Iwan Sugihartono

Makara Journal of Technology

Separation Study of Titanomagnetite Fe3-xTixO4 from Natural Sand at Indramayu, West Java. Titanomagnetite FeTiO4 has been obtained from metal sand which is separated from natural sand at Indramayu using magnetic separator with the magnetic field 0,3 Tesla. This method can improve titanomagnetite content from 32% to 63,6%. According to X-ray diffractometer (XRD) and data processing by general structure analyses system (GSAS) with χ2= 1,454 and Wrp = 0,1142 as correction factor of the peak to peak intensities, we conclude that χ2 about 0 and Wrp aproximately 10%. It indicates the datas with the error merely 0,1 can be accepted. Furthermore, …

Hydrogen Absorption Induced Slow Crack Growth In Austenitic Stainless Steels For Petrochemical Pressure Vessel Industries, Ronnie Higuchi Rusli

Makara Journal of Technology

Type 304L and type 309 austenitic stainless steels were tested either by exposed to gaseous hydrogen or undergoing polarized cathodic charging. Slow crack growth by straining was observed in type 304L, and the formation of α‘ martensite was indicated to be precursor for such cracking. Gross plastic deformation was observed at the tip of the notch, and a single crack grew slowly from this region in a direction approximately perpendicular to the tensile axis. Martensite formation is not a necessary condition for hydrogen embrittlement in the austenitic phase.

Development Of Technology Parameter Towards Shipbuilding Productivity Predictor Using Cubic Spline Approach, Bagiyo Suwasono, Sjarief Widjaja, Achmad Zubaydi, Zaed Yuliadi, I Nyoman Budiantara

Makara Journal of Technology

Development of Technology Parameter Towards Shipbuilding Productivity Predictor Using Cubic Spline Approach. Ability of production processes associated with state-of-the-art technology, which allows the shipbuilding, is customized with modern equipment. It will give impact to level of productivity and competitiveness. This study proposes a nonparametric regression cubic spline approach with 1 knot, 2 knots, and 3 knots. The application programs Tibco Spotfire S+ showed that a cubic spline with 2 knots (4.25 and 4.50) gave the best result with the value of GCV = 56.21556, and R2 = 94.03%.Estimation result of cubic spline with 2 knots for the PT. Batamec shipyard …

Shaft Torsional Vibration Response Of Vertical Axis Ocean Current Turbine Model Due To Torque Excitation, Adi Wirawan Husodo, I Ketut Aria Pria Utama, I Made Ariana

Makara Journal of Technology

Shaft Torsional Vibration Response of Vertical Axis Ocean Current Turbine Model Due to Torque Excitation. The current research aimed to study the torsional vibration response of Vertical Axis Ocean Current Turbine due to randomly torque excitation pattern, owing to the variety of ocean current velocity. The turbine model is composed of 3 aluminum blades of NACA 0018 connected to steel shaft. Turbine dimensions are 10 cm of chord, 1.8 cm of chamber and 100 cm of span. The variation of ocean current velocity is 0.5 m/s, 1.0 m/s, 1.5 m/s, 2.0 m/s, 2.5 m/s and 3.0 m/s. The Model has …

An Investigation Of The Influence Of Diaphragm Flexibility On Building Design Through A Comparison Of Forced Vibration Testing And Computational Analysis, Blake Alan Roskelley

Master's Theses

An assessment of the validity of idealizing a concrete diaphragm as rigid was performed through the modal analysis of three existing buildings. Modal analysis was performed both by physical experimentation and computational analysis. Experimental determination of the mode shapes shows that two of the three buildings’ diaphragms exhibited flexible behavior. The experimental results were compared to computational analysis results and were shown to be similar, confirming that that the two building diaphragms are not rigid. As a standard, diaphragms with aspect ratios less than three are permitted to be idealized as rigid per ASCE 7-05. To determine the effect of …

Research Agenda For Transportation Infrastructure Preservation And Renewal: Conference Report, Joseph L. Schofer, Leonard Evans, Michael P. Freeman, Larry L. Galehouse, Samer Madanat, Ali Maher, Sue Mcneil, John J. Myers, Robert L. Peskin, Butch Wlaschin

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

No abstract provided.

Reliability Estimation Of Complex Numerical Problems Using Modified Conditional Expectation Method, Christopher D. Eamon, Bulakorn Charumas

Civil and Environmental Engineering Faculty Research Publications

A simulation-based structural reliability analysis method is presented. It is intended as an alternate approach to estimate reliability for problems for which most-probable point of failure methods fail and when computational resources are limited. The proposed method combines conditional expectation and estimating the PDF or CDF of a selected portion of the limit state. In the proposed approach, complex limit state functions are simplified to two random variable problems. The success of the simplification depends on the quality of the CDF estimate. Results indicate that the method may provide accurate and efficient solutions for some difficult reliability problems.

Plain And Steel-Reinforced Concrete Shear Walls With And Without Cfrp Retrofitting, Ali Mohammed Salih Al Aloosi

Civil & Environmental Engineering Theses & Dissertations

This thesis presents the outcome- of a study of the behavior and strength of plain and steel-reinforced concrete shear walls with and without a window opening and Carbon Fiber-Reinforced Polymer (CFRP) retrofitting. A total of seven tests were conducted using six different shear walls. Each wall was subjected to a gradually increasing static load at one of it's top corners until the maximum load was reached. The load-deflection relations and the walls' failure patterns were observed and recorded. It was found that the window opening in the plain concrete wall reduced the wall load capacity by 18 percent. For the …

Performance-Based Analysis Of Steel Buildings: Special Concentric Braced Frame, Scott Michael Adams

Master's Theses

The performance-based analysis methods and evaluation criteria in ASCE 41-06 were used to evaluate a special concentric braced frame building based on the design standards in ASCE 7-05. A rectangular, six-story office building was evaluated using linear static, linear dynamic, nonlinear static, and nonlinear dynamic procedures. The results showed that the linear procedures underestimated damage compared to the nonlinear procedures, with the building performing to Life Safety for the linear procedures, and the nonlinear procedures indicating component damage beyond the intended Life Safety limit for the 2/3 maximum considered earthquake (MCE) hazard. This trend continued to the maximum considered earthquake …

Coated Steel Rebar For Enhanced Concrete-Steel Bond Strength And Corrosion Resistance, Genda Chen, Jeffery S. Volz, Richard K. Brow, Dongming Yan, Signo Tadeu Dos Reis, Chenglin Wu, Fujian Tang, Charles R. Werner, Xing Tao

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This report summarizes the findings and recommendations on the use of enamel coating in reinforced concrete structures both for bond strength and corrosion resistance of steel rebar. Extensive laboratory tests were conducted to characterize the properties of one- and two-layer enamel coatings. Pseudostatic tests were performed with pullout, beam and column specimens to characterize mechanical properties and develop design equations for the development length of steel rebar in lap splice and anchorage areas. The splice length equation was validated with the testing of large-scale columns under cyclic loading. For corrosion properties, ponding, salt spray, accelerated corrosion, potentiodynamic and electrochemical impedance …

Experimental Investigation Of Folded Plate Girders And Slab Joints Used In Modular Construction, Kyle A. Burner

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The folded plate girder, a newly proposed bridge girder, is investigated through this thesis. The folded plate girder is cold bent out of a single sheet of steel. The cold bending eliminates the costly and inconsistent shop welds found in traditional girders. The folded plate girder is meant for application in short span bridges. The girder was subjected to an equivalent 75 year lifetime loading to investigate the fatigue performance.

The rebar detail used in the closure region between adjacent slabs has been investigated in the past by the NCHRP 12-68 project. This thesis will proposes a hooked rebar detail …

Constructability Testing Of Folded Plate Girders, Luke A. Glaser

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

A new steel girder bridge system was developed at the University of Nebraska. The innovative girder design is a box girder folded from a single steel plate that has a trapezoid shape with an opening on the bottom. The girder has application in short span bridges and accelerated construction situations. The structural performance of the girder requires investigation in all stages of a bridge’s lifecycle. This thesis contains descriptions and results from the first two tests from a series of tests developed to evaluate this new girder shape. The objective of these two tests was to investigate the constructability of …

Supplement No. 2 To The North American Specification For The Design Of Cold-Formed Steel Structural Members, 2007 Edition, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Intricacies Of Professional Certifications For Quality Management (Qm), Edmund R. Martelli

Masters Theses & Specialist Projects

The modern manufacturing marketplace is extremely complex and constantly changing. Career professionals often seek job placement, career advancement, and continuing education through professional certifications. Professional certifications in the United States (U.S.) have been evolving since 1911. In the 1950s, engineering groups established professional certifications and licenses. In the 1980s, administration of accreditation of certification programs proliferated, and by the 1990s, many government and professional organizations sought to standardize procedures for the industry. Currently, professional certifications are available for virtually every profession and issued by multitudes of organizations.

Quality management (QM) encompasses an extensive combination ofprofessional abilities. Providers of professional certifications …

Modelling And Verification Of Response Of Rc Slabs Strengthened In Flexure With Mechanically Fastened Frp Laminates, Annalisa Napoli, Fabio Matta, Enzo Martinelli, Antonio Nanni, Roberto Realfonzo

Faculty Publications

Mechanically fastened fibre-reinforced polymer laminate systems are emerging as a promising means for the repair and strengthening of reinforced concrete members. This technology entails the use of pultruded carbon- and glass- vinyl ester fibre-reinforced polymer laminates with enhanced longitudinal bearing strength that are connected to the concrete substrate by means of steel anchors. Attractive applications are those for emergency repairs where constructability and speed of installation are critical requirements. In this paper, an experimental investigation is first presented that included laboratory testing of scaled reinforced concrete slabs strengthened with four different combinations of laminate lengths and fastener layouts to study …

Failure Literacy In Structural Engineering, Norbert J. Delatte

Civil and Environmental Engineering Faculty Publications

The history of the development of practice in many engineering disciplines is, in large part, the story of failures, both imminent and actual, and of the changes to designs, standards and procedures made as the result of timely interventions or forensic analyses. All engineers, and more particularly structural engineers, should be failure literate. Failure literacy means knowing about the critical historical failure cases that have shaped the profession: not merely the surface technical details, but the environment, the communications difficulties and the procedural issues. In the US, an intensive effort has been under way for nearly a decade to promote …

Comparison Of The Properties Of Portland Cement And Portland-Limestone Cement, Alex Lyatonga Mrema

Tanzania Journal of Engineering and Technology (TJET)

A study was made in a cement factory in Dar es Salaam, Tanzania, where Ordinary Portland Cement (CEM I 42.5N) and Portland-limestone cement (PLC) which has the brand name Twiga Cement Extra (CEM II/A-L/32.5R) are produced and conforming to the Tanzania Standard TZS 727 (Part1): 2002, which is equivalent to EN 197 published by the committee for European normalization (CEN). A comparison was made between the two types of cements in terms of physical, chemical and mechanical properties. It was found out that they all complied with the standards, that there was no significant difference in their setting times and …

The Effect Of Service Installations On Structural Integrity Of Slabs In Buildings, Ladislaus Lwambuka

Tanzania Journal of Engineering and Technology (TJET)

In building construction industry service installations, usually housed in conduit pipes, are commonly mounted inside reinforced concrete structural elements. This practice is adopted to attain aesthetical outlook at both interior and exterior surfaces of the buildings. Depending on the extent of service installations, the cross sectional area of the load bearing structural member is substantially reduced. However, the current structural design guidelines have no provision to accommodate the extent to which the existence of conduit pipes impairs the load bearing capacity of the structural element though reduced cross sectional area. This study has attempted to address this gap in structural …

Simplified Procedures For Seismic Analysis And Design Of Piers And Wharves In Marine Oil And Lng Terminals, Rakesh K. Goel

Civil and Environmental Engineering

No abstract provided.