Open Access. Powered by Scholars. Published by Universities.®

Structural Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

2002

Discipline
Institution
Keyword
Publication
Publication Type

Articles 1 - 30 of 98

Full-Text Articles in Structural Engineering

Application Of Remote Sensing For Mapping Soil Organic Matter Content, Bangun Muljo Sukojo, Wahono Wahono Dec 2002

Application Of Remote Sensing For Mapping Soil Organic Matter Content, Bangun Muljo Sukojo, Wahono Wahono

Makara Journal of Technology

Application of Remote Sensing for Mapping Soil Organic Matter Content. Information organic content is important in monitoring and managing the environment as well as doing agricultural production activities. This research tried to map soil organic content in Malang using remote sensing technology. The research uses 6 bands of data captured by Landsat TM (Thematic Mapper) satellite (band 1, 2, 3, 4, 5, 7). The research focuses on pixels having Normalized Difference Soil Index (NDSI) more than 0.3. Ground-truth data were collected by analysing organic content of soil samples using Black-Walkey method. The result of analysis shows that digital number of …

Go to article

Optimation Model Of Planning Investment Dockyard With Approach Multi Objective Goal Programming, Ali Azhar Dec 2002

Optimation Model Of Planning Investment Dockyard With Approach Multi Objective Goal Programming, Ali Azhar

Makara Journal of Technology

Optimation model of planning investment dockyard with approach multi objective goal programming. The purpose of this research is to determine decision variable, goal function, alternative priority and achievement function in investment planning. From this optimation component, the model of ship yard investment planning could be achieved. The model of developed model in this research was the optimation of ship yard investment planning using multi objective goal programming approach. The model consist of 5 decision variable, 11 goal function, 2 alternative priority and 11 achievement functions. The model implementation was done toward PT ASSI investment planning. The calculation using from Quantitative …

Go to article

Self-Ignition Properties Of Peat, Palm Shell Fibre And Woods, Yulianto Sulistyo Nugroho Dec 2002

Self-Ignition Properties Of Peat, Palm Shell Fibre And Woods, Yulianto Sulistyo Nugroho

Makara Journal of Technology

Self-ignition properties of peat, palm shell fibre and woods. Forest fire is one of the greatest environmental problems faced by Indonesia. Forest fires have destroyed million hectares of forest and land which cause economic loss, social problems including smoke related diseases and environmental disaster with long time consequences. The exothermic reactions of forest fuels that lead to fire can be initiated by a piloted flame and low-temperature oxidation mechanism. This paper presents the results of low temperature oxidation studies using forests fuel samples i.e. palm shell fibre, peat, woods and low-rank coal. The measured values of the critical oven temperatures …

Go to article

Iodat Analysis Content In Cooking Ingredients Using Iodometry And X-Ray Fluorescence Methods., Nelson Saksono Dec 2002

Iodat Analysis Content In Cooking Ingredients Using Iodometry And X-Ray Fluorescence Methods., Nelson Saksono

Makara Journal of Technology

Iodat Analysis Content in Cooking Ingredients Using Iodometry and X-ray Fluorescence Methods. Salt iodization program using iodine fortification into salt method is the best method that is effective and economical to overcome the problems caused by iodine deficiency. However in, its development there are some issues clamed that the use of iodized salt is ineffective since iodine content reduces, even disappear when the salt mix with other cooking ingredients. In order to investigated the existence of iodine in cooking ingredients, a research applying iodometry and X-ray fluorescence methods was carry out. The result obtained by iodometry method showed decreases in …

Go to article

Emission Gas Reducer On Motor Vehicle, Automobile, Light Engine Of Boat And Stationary Combustion Engine., I Gusti Bagus Wijaya Kusuma Dec 2002

Emission Gas Reducer On Motor Vehicle, Automobile, Light Engine Of Boat And Stationary Combustion Engine., I Gusti Bagus Wijaya Kusuma

Makara Journal of Technology

Emission gas reducer on motor vehicle, automobile, light engine of boat and stationary combustion engine. The use of motor vehicle should be followed by protection against damages on the environment, since the exhaust gas from combustion engine has significantly affect on air and environmental pollution. One method to solve the problems in air pollution has been done by using a re-heater designed in Mechanical Engineering Department, University of Udayana. In accordance to the test on the re-heater, it can be seen very clear that the re-heater has significantly reduce the CO emission of about 54%. It also reduces the CO2 …

Go to article

The Use Of 2d Plastic Grating For Surface Profile And Dimension Manufacture Product Measurements By Using Ndt Moiré Technique, Retno Wigajatri P., Dini Andiani Dec 2002

The Use Of 2d Plastic Grating For Surface Profile And Dimension Manufacture Product Measurements By Using Ndt Moiré Technique, Retno Wigajatri P., Dini Andiani

Makara Journal of Technology

The Use of 2D Plastic Grating for Surface Profile and Dimension Manufacture Product Measurements by Using NDT Moiré Technique. Research of measuring the shape and dimension of object using the moiré technique have been done. Measurement have been made by observing the moiré space as a result of interaction between grating and its shadow casted on the object’s surface caused by the projector lamp with CCD camera. The acquired data was further processed by way of off-line. By successive phase shifts that is π/2, π dan 3π/2 towards the table tennis ball at the distance of 48 cm from the …

Go to article

Interactive Learning Tools: Animating Statics, Nancy Hubing, David B. Oglesby, Timothy A. Philpot, Vikas Yellamraju, Richard H. Hall, Ralph E. Flori Dec 2002

Interactive Learning Tools: Animating Statics, Nancy Hubing, David B. Oglesby, Timothy A. Philpot, Vikas Yellamraju, Richard H. Hall, Ralph E. Flori

Business and Information Technology Faculty Research & Creative Works

Computer-Based Modules for Engineering Instruction Must Be Concise, Flexible, Educational and Engaging in Order to Effectively Supplement Traditional Classroom Teaching Tools. a Computer Example that Takes More Time Than a Chalkboard Presentation is Not Likely to Be Useful in Today's Engineering Classroom. Flexible Navigation is Necessary So that the Instructor Can Quickly and Easily Respond to Student Questions. Useful Modules Must Also Improve Problem-Solving Skills or Clarify Troublesome Concepts in Order to Be Considered Worthy of Inclusion in the Limited Class Time Available. Finally, and Perhaps Most Importantly, Effective Computer-Based Modules Must Meet the Challenge of Holding the Student's Attention. …

Go to article

Structural Behaviour Of Self-Piercing Riveted Connections In Steel Framed Housing, Stephen Moss, Mahen Mahendran Oct 2002

Structural Behaviour Of Self-Piercing Riveted Connections In Steel Framed Housing, Stephen Moss, Mahen Mahendran

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Self-piercing riveting involves the joining of two or more plates by using a rivet to pierce and clinch in a single operation. There is a distinct lack of information regarding the use of self-piercing riveted connections in cold-formed steel frames. Experimental research is being undertaken to investigate the structural behaviour of self-piercing riveted connections used in steel framed housing. To date, testing has been carried out on 0.75 mm to 1.15 mm G300 steels to determine the primary failure modes for self-piercing riveted connections and also to assess the applicability of standard single point lap shear tests to actual house …

Go to article

Seismic Performance Of Wall-Stud Shear Walls, Ludovic A. Fulop, Dan Dubina Oct 2002

Seismic Performance Of Wall-Stud Shear Walls, Ludovic A. Fulop, Dan Dubina

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The ever-increasing need for housing generated the search for new and innovative building methods to increase speed, efficiency and enhance quality, one direction being the use of light steel profiles as load bearing elements and different materials for cladding. Wind and seismic behavior of these structures is influenced by the hysteretic characteristics of the shear wall panels. In this paper a review of actual research in the field and results of a full-scale shear test program on wall panels are presented. Based on tests, a numerical equivalent model for hysteretic behavior of wall panels working in shear was built to …

Go to article

Structural Behavior Of Bolted Connections In Cold-Formed Steel Members, Emphasizing The Shear Lag Effect, Carlos Henrique Maiola, Maximiliano Malite, Jorge Munaiar Neto, Roberto Martins Goncalves Oct 2002

Structural Behavior Of Bolted Connections In Cold-Formed Steel Members, Emphasizing The Shear Lag Effect, Carlos Henrique Maiola, Maximiliano Malite, Jorge Munaiar Neto, Roberto Martins Goncalves

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Light-gage steel structures constituted mainly of cold-formed steel members have been widely employed in a variety metal construction in Brazil and many countries. The reduced thicknesses this elements making connection designing difficult due the occurrence of the local effects that generally govern these designs in thin elements. This paper presents and discusses the results of a experimental investigation of bolted connections in cold-formed angles (either equal or unequal legs) and channel members (1.55 to 3.75mm thickness), and an evaluation of the structural behavior of the connections with identification of the corresponding failure modes, with emphasis on the tensile capacity of …

Go to article

Local Buckling Tests On Cold-Formed Steel Beams, Cheng Yu, Benjamin W. Schafer Oct 2002

Local Buckling Tests On Cold-Formed Steel Beams, Cheng Yu, Benjamin W. Schafer

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

C- and Z-sections are two of the most common cold-formed steel shapes in use today. Accurate prediction of the bending performance of these sections is important for reliable and efficient cold-formed steel structures. Recent analytical work has highlighted discontinuities and inconsistencies in the AISI (1996) design provisions for stiffened elements under a stress gradient (i.e., the web of C- or Z-sections). New methods have been proposed for design, and an interim method has been adopted in the NAS (North American Specification 2001). However, existing tests on Cs and Zs do not provide a definitive evaluation of the design expressions, due …

Go to article

Bending And Web Crippling Interaction Of Cold-Formed Steel Members, Roger A. Laboube, J. A. Wallace, R. M. Schuster Oct 2002

Bending And Web Crippling Interaction Of Cold-Formed Steel Members, Roger A. Laboube, J. A. Wallace, R. M. Schuster

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The North American Specification has recently adopted a new web crippling approach for the Design of Cold-Formed Steel Structural Members (NAS, 2001). This approach is similar to what is currently in the Canadian S136 Standard (CSA, 1994). The current web crippling and bending interaction equations for single-web sections in the North American Specification (NAS 2001) are based on the previous web crippling methods that are contained in the American Iron and Steel Institute (AISI) Specification (AISI, 1996). As well, the moment component of the interaction equations was based on the previous reduced web strength method instead of the stress gradient …

Go to article

Web Crippling And Combined Bending And Web Crippling Of Cold-Formed Steel Box-Beam Headers, Sutton F. Stephens, Roger A. Laboube Oct 2002

Web Crippling And Combined Bending And Web Crippling Of Cold-Formed Steel Box-Beam Headers, Sutton F. Stephens, Roger A. Laboube

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Box-beam headers are commonly used in walls framed with cold-formed steel studs to span openings in bearing walls. Based on the results of previous experimental studies, it has been shown that box-beam headers subjected to interior one flange (IOF) loading have been conservatively designed. This paper presents the results of an ongoing experimental study conducted at the University of Missouri-Rolla to establish the web crippling strength of box-beam headers for an IOF loading condition. Box-beam header specimens were tested as a system consisting of two C-sections together with top and bottom track sections. The header configuration used in this study …

Go to article

Axial Strength Of Purlins Attached To Standing Seam Roof Panels, John A. Stolarczyk, James M. Fisher, Al Ghorbanpoor Oct 2002

Axial Strength Of Purlins Attached To Standing Seam Roof Panels, John A. Stolarczyk, James M. Fisher, Al Ghorbanpoor

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The purpose of this research was to determine the axial load capacity of Z-purlins with one flange attached to a standing seam roof system. The axial load capacity was determined by developing a relationship between the flexural uplift buckling strength and the axial buckling strength in the Z-purlin. This relationship was investigated using finite element models and by conducting a parametric study. At the conclusion of the parametric study, confirmatory tests were conducted to verify the finite element results. A relationship has been provided that relates the axial buckling strength in the Z-purlin to the flexural uplift buckling strength. This …

Go to article

Progress On The Direct Strength Method, Benjamin W. Schager Oct 2002

Progress On The Direct Strength Method, Benjamin W. Schager

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The Direct Strength method is a new design procedure for cold-formed steel members. The method employs elastic buckling solutions for the cross-section, instead of the element-by-element plate buckling solutions used in traditional design. The use of cross-section elastic buckling solutions insures inter-element compatibility and equilibrium. The Direct Strength method uses strength formulas on the gross section, similar to conventional column curves, for capacity prediction in local and distortional buckling. This avoids effective section calculations altogether. The reliability of the Direct Strength method is demonstrated for a broad selection of beams and columns by comparison with existing test data. Extension of …

Go to article

Compression Tests Of Cold-Reduced High Strength Steel Long Columns, Demao Yang, Gregory J. Hancock, Kim J. R. Rasmussen Oct 2002

Compression Tests Of Cold-Reduced High Strength Steel Long Columns, Demao Yang, Gregory J. Hancock, Kim J. R. Rasmussen

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

This paper describes a series of compression tests performed on long columns fabricated from cold-formed high strength steel plates with nominal yield stress of 550 MPa (80 ksi). The steel is classified as G550 to Australia Standard AS1397. The test results presented in this paper are the second stage of an Australian Research Council research project entitled "Compression Stability of High Strength Steel Sections with Low Strain-Hardening". A total of 28 long columns, which were made from two thicknesses of sheet steel (0.42 mm and 0.6 mm) (0.017 in. and 0.024 in.), were tested. A box shaped section was tested …

Go to article

Calibrations Of Bolted Cold-Formed Steel Connections In Bearing (With And Without Washers), Roger A. Laboube, J. A. Wallace, R. M. Schuster Oct 2002

Calibrations Of Bolted Cold-Formed Steel Connections In Bearing (With And Without Washers), Roger A. Laboube, J. A. Wallace, R. M. Schuster

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The bearing strength of bolted connections is treated differently in the two current North American Cold-Formed Steel Design documents, the AISI Specification in the USA (AISI 1996a) and the S136 Standard in Canada (CSA 1994). In the case of the S136 Standard (CSA 1994), only one expression is presented that applies to all bolted connections such as single and double shear, as well as, with and without washers. In the AISI Specification (AISI 1996a), however, a distinction is made between single shear and double shear connections and the use of washers. Contained in this paper are the calibration results of …

Go to article

Evaluation Of Bolt-Hole Elongation Stiffness For The Stiffness Prediction Of Cold-Formed Steel Bolted Moment-Connections, J. B. P. Lim, D. A. Nethercot Oct 2002

Evaluation Of Bolt-Hole Elongation Stiffness For The Stiffness Prediction Of Cold-Formed Steel Bolted Moment-Connections, J. B. P. Lim, D. A. Nethercot

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Cold-formed steel bolted moment-connections cannot be considered as rigid because of localised in-plane elongation of the bolt-holes due to bearing of the bolt-shank against the bolt-hole. To therefore calculate the rotational stiffness of such bolted moment-connections, it is necessary to know the load-extension characteristics of bolt-hole elongation. In this paper, a non-linear large- displacement elasto-plastic finite element idealisation of a plain bolt-shank in bearing against a bolt-hole is presented. Graphs of load against bolt-hole elongation are plotted that show good comparison with laboratory test results. A proposed modification of the results allows for the results of a fully-threaded bolt-shank to …

Go to article

Strength And Behavior Of Fillet Welded Connections In G450 Sheet Steel, Lip H. Teh, Gregory J. Hancock Oct 2002

Strength And Behavior Of Fillet Welded Connections In G450 Sheet Steel, Lip H. Teh, Gregory J. Hancock

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

G450 steel to AS 1397 is a cold-reduced sheet steel with in-line galvanizing. Its grade is 65 ksi (450 MPa) yield and 70 ksi (480 MPa) tensile strength. It is widely used in Australia for purlins, and is being used to fabricate light-weight Portal frames, often by welding. The effect of welding on G450 sheet steel in the heat affected zone was unknown and so the project was performed to investigate the strength of fillet welded connections. Transverse and longitudinal fillet welded connections in 0.06 in (1.5 mm) and 0.12 in (3.0 mm) sheet steels were tested to failure. The …

Go to article

Some Improvements To The Design Of Sandwich Panels Subject To Local Buckling Effects, Narayan Pokharel, Mahen Mahendran Oct 2002

Some Improvements To The Design Of Sandwich Panels Subject To Local Buckling Effects, Narayan Pokharel, Mahen Mahendran

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Past research into the local buckling behaviour of fully profiled sandwich panels has been based on polyurethane foams and lower grade steels, and not for very slender plates. The Australian sandwich panels use polystyrene foam and thinner (0.42 mm) and high strength steels (G550 with a minimum yield stress of 550 MPa), which are bonded together using separate adhesives. Therefore a research project on Australian sandwich panels was undertaken using experimental and finite element analyses. The experimental study on 50 foam-supported plate elements and associated finite element analyses produced a large database for sandwich panels subject to local buckling effects, …

Go to article

Variables Affecting The Shear-Bond Resistance Of Composite Floor Deck Systems, R. Tremlay, P. Gignac, G. Degrange, Colin A. Rogers Oct 2002

Variables Affecting The Shear-Bond Resistance Of Composite Floor Deck Systems, R. Tremlay, P. Gignac, G. Degrange, Colin A. Rogers

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The 1 1/2" composite deck section is among the more popular floor systems used in the construction of steel buildings in North America. The shear-bond between the steel deck and the concrete normally controls the capacity of a composite floor slab. Shear-bond can, for the most part, be attributed to the presence of mechanical interlock that results from the use of embossments formed in the deck webs during the rolling process. However, the extent of shear resistance between the concrete and the steel can also vary depending on the deck profile, steel thickness and grade, coating, as well as the …

Go to article

Preliminary R-Values For Seismic Design Of Steel Stud Shear Walls, Y. Zhao, Colin A. Rogers Oct 2002

Preliminary R-Values For Seismic Design Of Steel Stud Shear Walls, Y. Zhao, Colin A. Rogers

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Design codes recognize the ability of some structures to undergo significant inelastic deformation during a seismic event without reaching the point of collapse. In consideration of this behaviour, building codes provide force modification factors (R-values) to determine the reduced lateral loads that engineers may use in design. This paper presents an overview of the seismic requirements for various design standards and an explanation of how R-values may be determined from test results. The findings of an evaluation of existing steel stud shear wall test data, in addition to preliminary force modification factors for use in seismic design, are presented.

Go to article

Sway Stability Testing Of High Rise Rack Sub-Assemblages, Elisha Harris, Gregory J. Hancock Oct 2002

Sway Stability Testing Of High Rise Rack Sub-Assemblages, Elisha Harris, Gregory J. Hancock

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The stability in the down-aisle direction of high rise storage racks is usually provided by the beam-to-column and base-plate connections. In order to evaluate the effect of the beam-to-column connections, a complex test rig has been designed and developed at the University of Sydney to test rack sub-assemblages which are the lower levels of high rise rack systems. The rig is designed to apply up to 500 kN vertical load via gravity load simulators. Pins at the top and bottom of the uprights under test remove the effect of the base-plates on the lateral stability. To apply horizontal loads, a …

Go to article

Design Of Channels Subjected To Concentrated Bearing Load, Ben Young, Gregory J. Hancock Oct 2002

Design Of Channels Subjected To Concentrated Bearing Load, Ben Young, Gregory J. Hancock

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

A test program on cold-formed steel channels subjected to concentrated bearing load is presented in this paper. The web slenderness values of the channel specimens ranged from comparatively stocky webs of 15.3 to relatively more slender webs of 62.7. The tests were performed under end and interior loading conditions, and the test setup was different from the one specified in the North American Specification and the Australian/New Zealand Standard for cold-formed steel structures where the loading support is assumed free to rotate in the plane of the beam. The test specimens were seated on a fixed flat solid steel base …

Go to article

Web Crippling Strength Of Multi-Web Steel Deck Sections Subjected To End One Flange Loading, Onur Avci, Samuel W. Easterling Oct 2002

Web Crippling Strength Of Multi-Web Steel Deck Sections Subjected To End One Flange Loading, Onur Avci, Samuel W. Easterling

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Cold-formed steel deck profiles are extensively used in building construction due to their versatility and economical considerations. Web crippling is one of the failure modes for these multi-web profiles. The 1996-AISI Specification for the Design of Cold-Formed Steel Structural Members provisions for web crippling are believed to be conservative for multi-web deck sections. They are based on unfastened specimens and are limited to the use of decks with certain geometric parameters. The unified web crippling equation of the North American Specification for the Design of Cold-Formed Steel Structural Members (AISI 2001) is also limited to certain geometric parameters. Although it …

Go to article

Design Provisions For Sections Containing Unstiffened Elements Under Stress Gradients, M. R. Bambach, Kim J. R. Rasmussen Oct 2002

Design Provisions For Sections Containing Unstiffened Elements Under Stress Gradients, M. R. Bambach, Kim J. R. Rasmussen

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Current American design provisions treat unstiffened elements under stress gradients as if they were uniformly compressed for effective width calculations. This paper presents a design method for calculating the effective width of these elements, based on plate test results. Current international codes allow the capacity of sections that contain unstiffened elements under stress gradients to be calculated on the basis of initiation of yielding in the section. A non-iterative method for the calculation of the capacity, based on inelastic reserve capacity, is presented. The method is shown to be in good agreement with experimental data of I-sections and plain channels …

Go to article

The Behaviour Of Drive-In Storage Structures, M. H. R. Godley Oct 2002

The Behaviour Of Drive-In Storage Structures, M. H. R. Godley

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The paper describes the behaviour of Drive-in and Drive-thru pallet rack structures. It proposes a number of simplified two-dimensional models for the analysis of such structures. These models are shown to be conservative and take account of the non-linear behaviour of the structures. The paper makes some comparisons between the output from these and a 3-D finite element program. The effects of friction between the pallet and the supporting rail is discussed briefly.

Go to article

Strength And Behavior Of Flare-Bevel And Flare-Vee Welded Connections In G450 Sheet Steel, Lip H. Teh, Gregory J. Hancock Oct 2002

Strength And Behavior Of Flare-Bevel And Flare-Vee Welded Connections In G450 Sheet Steel, Lip H. Teh, Gregory J. Hancock

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

G450 steel to AS 1397 is a cold-reduced sheet steel with in-line galvanizing. Its grade is 65 ksi (450 MPa) yield and 70 ksi (480 MPa) tensile strength. It is widely used in Australia for purlins, and is being used to fabricate light-weight portal frames, often by welding. The effect of welding on G450 sheet steel in the heat affected zone (HAZ) was unknown and so the project was performed to investigate the strength of flare-bevel and flare-vee welded connections. Flare-bevel and flare-vee welded connections in 0.06-in (1.5-mm) and 0.12-in (3.0-mm) sheet steels were tested to failure. The failure modes …

Go to article

Compression Tests Of Cold-Reduced High Strength Steel Stub Columns, Demao Yang, Gregory J. Hancock Oct 2002

Compression Tests Of Cold-Reduced High Strength Steel Stub Columns, Demao Yang, Gregory J. Hancock

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

This paper describes a series of compression tests performed on stub columns fabricated from cold-formed high strength steel plates with nominal yield stress of 550 MPa. (80 ksi) The steel is classified as G550 to Australia Standard AS 1397. The test results presented in this paper are the first stage of an Australian Research Council research project entitled "Compression Stability of High Strength Steel Sections with Low Strain-Hardening". The tests include lipped-square and hexagonal sections, including 94 box-shaped fix-ended stub columns. The purpose of these tests was to determine the influence of low strain hardening of G550 steel on the …

Go to article

Study Of Innovative Built-Up Cold-Formed Beams, Gianmaria Di Lorenzo, Raffaele Landolfo Oct 2002

Study Of Innovative Built-Up Cold-Formed Beams, Gianmaria Di Lorenzo, Raffaele Landolfo

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

In the present work innovative built-up cold-formed steel beams are presented. These are obtained by combining the pressing and cold-rolling forming techniques of steel sheets, along with the use of suitable connecting systems. Firstly, the beam shape features and the possible application fields, as well as the research project devoted to the assessment of their structural behaviour, are discussed. Then, experimental results concerning the characterization of both sheet material properties and connecting system performances are shown. In particular, the study of the sheet material is carried out by using an appropriate methodology of analysis, aiming at evaluating both mechanical and …

Go to article

Next Last