Structural Engineering Commons^™

Estimation Of The Mechanical Properties Of South Carolina Timber Piles Using Non-Destructive Evaluation Methods And Experimentally-Informed Models, Aashish Sapkota

All Theses

South Carolina has about 2,600 bridges that are supported by nearly 75,000 timber piles. They are increasingly vulnerable to biological decay, cracking and impact damages after decades of service. Current inspection methods used by the South Carolina Department of Transportation (SCDOT), such as hammer sounding and awl probing, are labor-intensive and expensive. This study investigated non-destructive evaluation (NDE) methods, including micro-resistance drilling and stress wave timing, as alternatives for assessing timber pile condition.

Ten timber piles were collected from two South Carolina bridges, and their above-grade portions were cut into 40 specimens approximately 13 to 15 inches long. Specimens were …

Dynamic Topology Optimization And Experimental Validation Of Reinforcement For Pcb Robotics, Ryan G. Semler

All Theses

Ongoing research between Clemson University and the NASA Jet Propulsion Laboratory (JPL) has been conducted to characterize and assess rigid-flex printed circuit board (PCB) robotics subjected to dynamic loads. A lightweight, PCB lunar rover, PUFFER (Pop-Up Flat Folding Explorer Robot), was designed by NASA JPL for Mars missions, but its deployment for lunar missions has been investigated as well. Its current architecture, however, is insufficient for navigating and surviving the lunar environment, and reinforcement has been recommended as a solution to protect larger panels.

This research work presents a dynamic topology optimization process for PCB panel reinforcement. A thorough literature …

Experimental Determination Of Modulus Of Rupture For Concrete Masonry Beams And Implications For The Tms 402/602 Code, Shreedhar K C

All Theses

Currently, the experimental database for Modulus of Rupture (MOR) of masonry beams is limited, and current provisions in TMS 402/602-22 use the MOR values from wallette tests. The primary goal of this research is to experimentally determine the parameters that influence MOR. The secondary goal of this work is to compare the MOR values from beam and bond wrench tests obtained in this study with each other as well as with values published in the literature. The standard ASTM E518 test was used for determining MOR values for beams, and a modified approach to ASTM C1072 that nullifies the eccentricity …

Field Evaluation Of Transverse Post-Tensioning And Latex Modified Concrete On Bridge Load Distribution, Paige Waters

All Theses

The Airport Road Bridge (ARB) over Rocky Creek in Greenwood, SC is one of 377 channel bridges in South Carolina currently load-posted, limiting vehicle weight and potentially restricting access to vital services. The South Carolina Department of Transportation (SCDOT) seeks a cost-effective method to strengthen these bridges and enhance their load-sharing capacity.

Through live load field testing, this research seeks to use two retrofitting techniques – transverse post-tensioning (PT) and latex modified concrete (LMC) overlay – to determine whether or not channel bridges can be improved. Direct tension testing was also performed to evaluate the substrate-overlay bond of the LMC …

Quantifying Hurricane Effects On Housing: Evaluating Damage, Loss, And Shelter Demands Using Historical And Simulated Storm Tracks, Adish Deep Shakya

All Theses

This research introduces an advanced framework which employs parametric wind field models for peak wind speeds, and building fragility curves, loss functions, and demographic data to estimate for estimating housing damage and loss. The uninhabitable units immediate displaced households, short-term and long-term shelter need households are determined. with a particular focus on those eligible for FEMA assistance. The framework's validity is reinforced by a high correlation in the analysis of recent hurricane events between estimated numbers of displaced households and actual FEMA aid recipients, where FEMA aids about 20-60% of the predicted long-term displaced households. A novel application of the …

Analytical And Experimental Studies To Support Codification Of Lightweight Grout For Masonry Design, Cooper Banks

All Theses

Lightweight (LW) aggregates have many potential benefits in masonry construction including minimizing mass, improving thermal performance, and reducing the potential for shrinkage cracking via internal curing. The current masonry design standard, TMS 402/602-22, permits lightweight aggregate in the production of concrete masonry units (CMU), but there has been insufficient testing of masonry assemblies to permit designing with LW grout. Shrestha et al. characterized LW grouts bond to reinforcement, shear strength, tension and shear pullout behavior of anchors and proposed possible reduction factors for design. Hiner characterized the flexural bond strength LW grouted masonry assemblies and proposed possible reduction factors for …

Effect Of Latex Modified Concrete Overlays With Reduced Surface Preparation On The Load Distribution And Flexural Strength Of Channel Girders, Samuel Dodd

All Theses

This thesis investigates the use of a Latex Modified Concrete (LMC) overlay to increase the strength of prestressed channel girders and enhance their ability to distribute load. The research conducted in this thesis involved material testing of several different LMC mixes and flexural testing of an LMC overlay and girder system. The material testing was used to determine a reasonable LMC mix design and surface preparation method to be used for the overlay. Based on material testing it was concluded that a rapid-set mix and pressure washing of the girder surfaces were a reasonable mix design and surface preparation for …

Experimental Investigation Of The Long-Term Bending Deflection And Creep Performance Of Cross-Laminated Timber (Clt), Aaron Desantis

All Theses

Rising popularity in mass timber construction for residential and commercial projects has escalated the need to develop and increase understanding of mass timber products both from a strength and serviceability perspective. For cross-laminated timber (CLT) there is a significant lack of research on the creep characteristics also known as long-term deflection behavior. Creep is particularly important for products such as CLT that are used for floors with longer spans. Full-scale creep testing was conducted using 5-ply CLT panels over the course of 6 months in a controlled environment under dry service condition. Testing resulted in average final deflections 1.73 times …

Effect Of Transverse Post-Tensioning On Moment Distribution Between Channel Girders, William Eubanks

All Theses

This thesis investigates the strength of prestressed concrete channel girders used

in bridges in South Carolina and how to improve their load distribution. The specimens

are 30 feet in length, 33 inches wide and 17 inches deep. South Carolina has 377 bridges

containing prestressed concrete channel girders and many of these bridges received a

poor load rating in a recent load rating project conducted by the South Carolina

Department of Transportation (SCDOT). The research included flexural testing of seven

individual channel girders and load distribution tests of three transversely post-tensioned

channel girders. Individual flexural testing was done to determine the …

Vibration Fatigue Of Leaded Solder Joint Interconnects For Pcb Electronics, John Crowder

All Theses

With the increasing prevalence of electronic equipment worldwide, there is also a decrease in the size of the components on their printed circuit boards (PCBs), leading to an increase in the density of these components. A significant amount of failure in electronic equipment is vibration fatigue of solder joints and their attachments. However, the complexity of these PCBs and their components has made finite element modeling (FEM) more complex, adding considerable time to create and analyze a model.

This paper aims to provide a literature review for the vibration fatigue of leaded solder components, create a test setup, and validate …

Fatigue Performance Of Flexural Retrofits For Precast Slab Bridges, Ian Stewart

All Theses

This thesis discusses flexural and cyclic load testing of two potential retrofits for pre-cast slab bridges. These slabs came from South Carolina Department of Transportation (SCDOT) decommissioned bridges as a part of an ongoing project with SCDOT. The first is a Carbon Fiber Reinforced Plate (CFRP) retrofit where four CFRP plates were adhesively bonded to the bottom of a slab. The second is a steel plate that was mechanically attached to the bottom of a slab using bolted connections. The bolts were cast into grouted holes in the slab. To better understand the failure mode of these retrofits and their …

Assessing Key Factors Influencing Fire-Induced Spalling Of Concrete Using Explainable Artificial Intelligence (Xai), Mohammad Khaled Gazi Albashiti

All Theses

This thesis adopts eXplainable Artificial Intelligence (XAI) to identify the key factors influencing the fire-induced spalling of concrete and to extract new insights into the fire-induced spalling phenomenon. In this pursuit, an XAI model was developed, validated, and then augmented with two explainability measures, namely, Shapley Additive exPlanations (SHAP) and Local Interpretable Model-Agnostic Explanations (LIME). The proposed XAI model not only can predict the fire-induced spalling with high accuracy (i.e., >92 %) but can also articulate the reasoning behind its predictions (as in, the proposed model can specify the rationale for each prediction instance); thus, providing us with valuable insights …

Flexural Bond Strength Of Masonry Assemblies With Lightweight Grout, Benjamin L. Hiner

All Theses

Lightweight grout has many potential benefits in masonry construction, including minimizing mass, improving thermal performance, and potentially reducing shrinkage cracking via internal curing. However, insufficient testing of masonry assemblies with lightweight grout has been conducted to suggest appropriate design modification factors akin to the lambda factor in ACI 318-19. The objective of this paper is to study the tensile bond behavior of masonry assemblies grouted with lightweight grout and to suggest appropriate equations for predicting design capacity. A moment couple test is designed specifically for grouted masonry assemblies and has additional capacity compared to the traditional ASTM 1072 bond wrench …

Flexural Testing Of Precast Reinforced Concrete Bridge Slabs, Evaluation Of Deterioration And Strengthening Applications, Alyssa Leaman

All Theses

This thesis investigates the strength of flat precast concrete slabs that were taken from decommissioned South Carolina bridges. The specimens tested spanned 14 ft (4.3 m) or 15 ft (4.6 m), were 5 ft (1.5 m) or 5.5 ft (1.7 m) wide, and 8.25 in (210 mm) thick. In South Carolina, there are approximately 3000 similar bridges that use these slab members. Testing was conducted to determine the flexural capacity of “typical” slabs and the residual strength of slabs having visible deterioration of both the rebar and the concrete. For the slabs that were load rated below the new standards, …

Performance Based Design And Machine Learning In Structural Fire Engineering: A Case For Masonry, Deanna Craig

All Theses

The volatile and extreme nature of fire makes structural fire engineering unique in that the load actions dictating design are intense but not geographically or seasonally bound. Simply, fire can break out anywhere, at any time, and for any number of reasons. Despite the apparent need, fire design of structures still relies on expensive fire tests, complex finite element simulations, and outdated procedures with little room for innovation. This thesis will make a case for adopting the principles of performance-based design and machine learning in structural fire engineering to simplify the process and promote the consideration of fire in all …

Rapidly Deployable Structures For Disaster Relief And Military Use, Jayson Leonard

All Theses

Rapidly deployable structures currently play a vital role in the recovery aspect of disaster-stricken areas and the safety of military personnel in hostile zones. More recently there has also been a need for the structures to deal with unforeseen disruptions caused by the COVID pandemic, such as COVID testing centers or backyard pop-up offices. These structures could be used in different environments and serve many other purposes. Along with the structural performance of these shelters, they need to integrate into systems set in place effortlessly. For that reason, four key factors were taken into consideration, namely (1) deployability (how difficult …

The Evacuation Simulation Of Wheelchair Users In A Building Fire: An Initial Dynamic Characterization Of Structural Egress Components, Haley Hostetter

All Theses

People with disabilities are one of the most vulnerable groups involved in building fires. According to the U.S. Fire Administration, in the United States alone, an estimated 700 home fires involve people with physical disabilities each year while over 1700 involve those with mental health disorders. Despite this, the current body of literature shows few studies focused on the evacuation of disabled people. This is a direct result of past and present social injustice on people with disabilities and has resulted in high injury and death rates during fires. To combat this, enrich the literature, and improve their experiences in …

Development Of Lambda Factors For Masonry Design With Lightweight Grout, Rumi Shrestha

All Theses

Reduction in structural mass, improvement in thermal performance, and reduction in shrinkage cracking through internal curing are some of the reasons that lightweight (LW) aggregates have been used in structures and pavements for decades. However, lightweight grout is still not permitted for use in reinforced masonry construction by the TMS 402/602-16 code. In order to realize the benefits of lightweight grout in U.S. reinforced masonry construction, a codified procedure for its use is required which must be informed by experimental testing.

This research is a pilot project directed to characterize the performance of LW grout in comparison to normal weight …

Development And Promotion Of Mass Timber Noise Barrier For Highways, Harsh Bothra

All Theses

Highways are some of the biggest causes of noise pollution in the United States of America. To deal with the traffic noise coming from these highways, noise barriers have been erected across major highways. The goal is to reduce as much noise as possible through a sustainable solution. Unfortunately, the use of steel and concrete, commonly used materials, have undesired environmental impacts. A suggested sustainable alternative material would be mass timber. Mass timber products such as cross-laminated timber (CLT) and mass plywood panels (MPP) has attracted the attention of the construction industry in the U.S, as they are sustainable, light, …