Structural Engineering Commons^™

Vibration Fatigue Of Leaded Solder Joint Interconnects For Pcb Electronics, John Crowder

All Theses

With the increasing prevalence of electronic equipment worldwide, there is also a decrease in the size of the components on their printed circuit boards (PCBs), leading to an increase in the density of these components. A significant amount of failure in electronic equipment is vibration fatigue of solder joints and their attachments. However, the complexity of these PCBs and their components has made finite element modeling (FEM) more complex, adding considerable time to create and analyze a model.

This paper aims to provide a literature review for the vibration fatigue of leaded solder components, create a test setup, and validate …

Fatigue Performance Of Flexural Retrofits For Precast Slab Bridges, Ian Stewart

All Theses

This thesis discusses flexural and cyclic load testing of two potential retrofits for pre-cast slab bridges. These slabs came from South Carolina Department of Transportation (SCDOT) decommissioned bridges as a part of an ongoing project with SCDOT. The first is a Carbon Fiber Reinforced Plate (CFRP) retrofit where four CFRP plates were adhesively bonded to the bottom of a slab. The second is a steel plate that was mechanically attached to the bottom of a slab using bolted connections. The bolts were cast into grouted holes in the slab. To better understand the failure mode of these retrofits and their …

Investigations Into Flange Surface Friction Effects On Shear Stud Load Transfer In Composite Bridge Girders, Callie Clark

Graduate Theses and Dissertations

Composite bridge behavior is commonly achieved through headed shear studs welded tothe steel girder flange and embedded in the concrete deck. Current AASHTO provisions for estimating demands on shear studs during service-level loading consider only bearing load transfer, neglecting adhesion bonding and friction load transfer between the concrete deck and girder flange. Quantifying alternative load transfer mechanisms across the steel-concrete interface may result in improved steel bridge economy by reducing the number of studs required in a composite girder design. This study investigates the effects of flange surface friction (considering various coatings) on resulting stud demands using both experimental testing …

Cyclic Behavior Of Laterally Skewed Special Moment Frame Connections: Experimental Testing And System-Level Analyses, Mohammad Hossein Kashefizadeh

Graduate Theses and Dissertations

Special moment frames (SMFs) are frequently used in high seismic areas for architecturally constrained designs. SMFs provide lateral system stiffness without the use of braces that often obstruct views and architectural features. Current American Institute of Steel Construction (ASIC) provisions (AISC 341-16) provide prequalified SMF connection details; however, all prequalified details only consider orthogonal connections between the beam and column. This dissertation investigates the effect of adding skew within SMF beam-to-column connections. The study presented herein involves system-level dynamic time-history analyses of skewed SMF connections, the analytical component-level investigation into the effect of the concrete slab on behavior of the …

Comparision Of Fillet-Welded Base Plate Fatigue Design For Highway Support Structures With Laboratory Research Tests, William Shea

Williams Honors College, Honors Research Projects

There are many types of vertical structures along highways that serve unique purposes. These structures include traffic signs for directing, warning, or regulating traffic, luminaires for distributing and directing light, traffic signals supporting equipment such as traffic lights, and combination structures including any combination of the aforementioned structures. Highway support structures are typically fabricated from steel or aluminum and are designed to the guidelines and specifications of the AASHTO Standard Specifications for Structural Supports for Highway Signs, Luminaires, and Traffic Signals. The structures are connected to a foundation by anchor bolts through a welded base plate. Often a cause …

Testing And Development Of Pre-Stressed Cfrp Retrofit Strategies For Controlling Fatigue Cracking In Steel Waterway Lock Gate Structures, Maggie Langston

Graduate Theses and Dissertations

Steel waterway lock gates across the national inland waterway transportation network are reaching and exceeding their intended service life, often experiencing component failures that lead to service interruptions. Unscheduled maintenance and repair of lock gates can be expensive and cause economic ripples throughout the entire inland waterway network. These lock gate component failures are often caused by fatigue cracking from repeated loading during operation. This thesis develops and tests a prestressed carbon fiber reinforced polymer (CFRP) fatigue retrofit for controlling fatigue demands within lock gate components. The study expands upon a recent analytical work by Lozano (2017) by experimentally investigating …

Automated Pin-Dot Marking Effects On A709-Gr50 Steel Plate Fatigue Capacity, Michael Andrew Noernberg

Graduate Theses and Dissertations

During fabrication of multi-piece steel bridge assemblies, markings are often made on the steel surface to identify/track individual pieces or to provide reference for fabrication layout or later erection. Automated marking methods such as computer numerically controlled (CNC) pin-dot marking offer fabrication efficiencies; however, for marked steel sections subjected to frequent or repeated loading (i.e. bridge girders) many code specifications require experimental testing to verify any marking effects on fatigue capacity. In this study, the effects of automated pin-dot markings on the fatigue capacity of A709-Gr50 bridge steel are experimentally investigated from 13 specimens considering 2 marking frequencies (corresponding to …

Dynamic Behavior And Fatigue Life Of Highway Bridges Due To Doubling Heavy Vehicles, Arash Tarighi

FIU Electronic Theses and Dissertations

An increase in the demand for the freight shipping in the United States has been predicted for the near future and Longer Combination Vehicles (LCVs), which can carry more loads in each trip, seem like a good solution for the problem. Currently, utilizing LCVs is not permitted in most states of the US and little research has been conducted on the effects of these heavy vehicles on the roads and bridges. In this research, efforts are made to study these effects by comparing the dynamic and fatigue effects of LCVs with more common trucks.

Ten Steel and prestressed concrete bridges …

Fatigue Testing And Data Analysis Of Welded Steel Cruciform Joints, Alina Shrestha

University of New Orleans Theses and Dissertations

In this study, ABS Publication 115, “Guidance on Fatigue Assessment of Offshore Structures” is briefly reviewed. Emphasis is on the S-N curves based fatigue assessment approach of non-tubular joints, and both size and environment effects are also considered. Further, fatigue tests are performed to study the fatigue strength of load-carrying and non-load-carrying steel cruciform joints that represent typical joint types in marine structures. The experimental results are then compared against ABS fatigue assessment methods, based on nominal stress approach, which demonstrates a need for better fatigue evaluation parameter. A good fatigue parameter by definition should be consistent and should correlate …

Creep, Fatigue And Creep-Fatigue Interactions In Modified 9% Cr - 1% Mo (P91) Steels, Valliappa Kalyanasundaram

Graduate Theses and Dissertations

Grade P91 steel, from the class of advanced high-chrome ferritic steels, is one of the preferred materials for many elevated temperature structural components. Creep-fatigue (C-F) interactions, along with oxidation, can accelerate the kinetics of damage accumulation and consequently reduce such components' life. Hence, reliable C-F test data is required for meticulous consideration of C-F interactions and oxidation, which in turn is vital for sound design practices. It is also imperative to develop analytical constitutive models that can simulate and predict material response under various long-term in-service conditions using experimental data from short-term laboratory experiments. Consequently, the major objectives of the …

Reliability-Based Fatigue Assessment Of Mast-Arm Sign Support Structures, Joseph A. Diekfuss

Dissertations (1934 -)

Over the past few decades, there have been issues of poor fatigue performance (the main failure mechanism) of the welded, tube-to-transverse plate connections within sign support structures. Review of the literature has indicated that a considerable amount of research has been devoted to identifying the structural response characteristics of these signs. Others have tried to identify how these connections may be repaired, retrofitted or simply better designed to sustain longer fatigue lives. However, little attention has been given to using a systematic reliability-based approach to assess the risk of fatigue-induced fracture in these structures.

Using a reliability-based approach to solve …

Durability And Fatigue Behavior Of Cip Concrete Connections For Accelerated Bridge Construction, Peng Zhu

Doctoral Dissertations

Continuous longitudinal and transverse U-bar joint connections between flanges of the decked bulb-Ts (DBTs) or between precast panels for accelerated bridge construction are investigated. The procedure for selecting durable closure pour (CP) materials for the connections is discussed firstly. The accelerated construction is quantified as two categories: overnight cure and 7-day cure of CP materials. Candidate materials are selected first based on literature review as well as tests of compressive strength and flow and workability. Then, performance criteria for selecting durable CP materials for both categories are developed based on durability tests of selected candidate materials. These durability tests include …

Development Of Innovative Load Transfer Mechanism To Reduce Hurricane-Induced Failures In New And Existing Residential Construction, Sheikh Saad Ahmed

FIU Electronic Theses and Dissertations

Implicit in current design practice of minimum uplift capacity, is the assumption that the connection's capacity is proportional to the number of fasteners per connection joint. This assumption may overestimate the capacity of joints by a factor of two or more and maybe the cause of connection failures in extreme wind events. The current research serves to modify the current practice by proposing a realistic relationship between the number of fasteners and the capacity of the joint. The research is also aimed at further development of non-intrusive continuous load path (CLP) connection system using Glass Fiber Reinforced Polymer (GFRP) and …

Investigation Of The Behavior Of Open Cell Aluminum Foam, Patrick J. Veale

Masters Theses 1911 - February 2014

The study investigates the behavior open cell aluminum foam in scenarios applicable to potential use in structural applications. Behavior was examined through mechanical testing, computer modeling and analytic expressions. Existing assumptions about the foam characteristics that define the elastic properties were expanded to include contributions of axial and shear deformations in addition to bending and were rewritten in terms of the axial and bending stiffness ratios of ligaments. Compressive and tensile tests were performed to gain a measure of the elastic properties of the foam as well as the behavior and failure mechanisms in both loading conditions. The materials used …

Investigation Of Cause Of Cracked Stringer On The Blanchette Bridge, Ward Marianos Jr., Genda Chen, Nestore Galati, Fabio Matta

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The Blanchette Bridge carries Interstate 70 across the Missouri River, connecting St. Louis and St. Charles counties in eastern Missouri. The westbound bridge was constructed in 1958. In 1979, the original reinforced concrete roadway deck on the bridge was replaced with a steel grid deck system, welded to supporting girders and stringers. In 1999 and 2005, cracks were discovered in stringers on the bridge approach spans. The stringers were repaired with bolted splices.

The investigation of the cracking included preliminary analyses, review of historical documents, detailed finite element analyses, and field testing of the bridge. The cracking was determined to …