Structural Engineering Commons^™

Developments In Performance Monitoring Of Concrete Exposed To Extreme Environments., W. J. Mccarter, T. M. Chrisp, G. Starrs, A. Adamson, E. Owens, P. A. M. Basheer, S. V. Nanukuttan, S. Srinivasan, Niall Holmes

Articles

The performance of the surface zone of concrete is acknowledged as a major factor governing the rate of deterioration of reinforced concrete structures because it provides the only barrier to the ingress of water containing dissolved ionic species such as chlorides, which ultimately initiate corrosion of the reinforcement. In situ monitoring of cover-zone concrete is therefore critical in attempting to make realistic predictions as to the in-service performance of the structure. To this end, this paper presents developments in a remote interrogation system to allow for continuous, real-time monitoring of the cover-zone concrete from an office setting. Use is made …

Development Of Self-Stressing System For Bridge Application With Emphasis On Precast Panel Deck System, Marcelo Ferreira Da Silva

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Steel girder bridges often utilize continuity over the pier to reduce interior forces on the spans. In continuous structures with composite concrete decks, the location of maximum negative bending moment is over the interior supports. This moment produces tensile stresses in the concrete deck and compressive stress in the bottom flanges of the girders. The tensile stress in the deck leads to cracking which allow intrusion of moisture and road salt, causing corrosion of the reinforcement and supporting girders. Continued maintenance is required to forestall the deterioration; however, replacement of the deck is eventually required.

To overcome this problem, a …

Development Of A Design Procedure For Concrete Traffic Barrier Attachments To Bridge Decks Utilizing Epoxy Concrete Anchors, Benjamin J. Dickey

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

A guide for the design of epoxy anchors for the use in concrete traffic barriers was developed in this study. A series of dynamic bogie tests and static tests was conducted on single and double anchors. The dynamic increase factor for the noted anchors was determined to be 1.06. Protective epoxy coatings for the anchors was observed to contribute to a 9 percent decrease in anchorage strength. The effects of anchors located in close proximity to each other was also investigated. Calibration factors were developed to apply recommended changes to the ACI code for use in bridge rail anchorages.

A …

Expanding The Length Of Jointless Bridges By Providing Rotational Capacity Over The Pile Head, Ardalan Sherafati

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Jointless bridges have been in service for more than 50 years. Since no expansion joint is utilized in these structures, they have longer service life, reduced maintenance and construction costs, improved riding quality, and added redundancy. Because of integrity of the superstructure with the substructure, the thermal movements as well as other longitudinal movements are transferred to substructure. These lateral movements can induce relatively large forces and moments in the substructure elements including the abutment and the piles. Typically, flexible foundations which include single row of piles are preferred in jointless bridges to reduce the stiffness of the system against …

Wim Based Load Models For Bridge Serviceability Limit States, Przemyslaw Rakoczy

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The safety of aging bridge inventory is one of the main concerns of the state and federal agencies. Therefore, there is a need to quantify the safety margin of existing infrastructure and new design bridges. The Serviceability Limit States, i.e. fatigue, requires additional statistical parameters and not only the maximum values but also load spectra, i.e. frequency of occurrence of loads. The maximum values are needed for shorter time periods, such as day, week, month or year. Load spectra as well as material resistance are random variables. To quantify the safety margin of existing and future bridges load and resistance …

Effect Of Copper Addition On Mechanical Properties And Electrical Conductivity Of Pp/C-Cu Bipolar Plate Composites, Anne Zulfia, Taufik Abimanyu, Verina Warga Dalam

Makara Journal of Technology

Effect of Copper Addition on Mechanical Properties and Electrical Conductivity of PP/C-Cu Bipolar Plate Composites. Bipolar plate is a major component in PEM fuel cell which possess main function of collecting and removing electrons from anode to cathode. Therefore, materials for bipolar plates produced must have high electrical conductivity. To obtain bipolar plate materials which is cheap, lightweight and high conductivity, so it is developed bipolar plates material based on PP/C-Cu composite. PP/C-Cu composites has been made by mixing all materials then compounding, rheomix, hot blending and hot press. Cu (Copper) has been used various from 0.1 wt%, 1 wt% …

Application Of Empirical Orthogonal Function Models To Analyze Shoreline Change At Bangkalan Madura, Darius Arkwright, Suntoyo Suntoyo

Makara Journal of Technology

Bangkalan’s shoreline, especially on the opposite side of Surabaya, has been evaluated to determine the morphological changes due to wave attack, near-shore current, long-shore sediment transport and coastal configuration. This research aims to determine the dominant patterns of variation of Bangkalan’s shoreline change, expressed by Eigen-function in empirical orthogonal function (EOF) models. That was started with data collection such as oceanographic data (wave and tidal), bathymetry and topographic map and sediment data. All data was used for forecasting two-monthly shoreline. Coordinate of two-monthly shoreline was used as input of EOF model. The first Eigen mode is a profile of shoreline …

The Effectiveness Of Anaerobic Baffled Reactor And Rotating Biological Contactor In Batik Wastewater Treatment, Augustinus Ignatius Kristijanto, Widhi Handayani, Purwanti Asih Anna Levi

Makara Journal of Technology

Batik is one of popular arts of Indonesia. The batik industries in Sragen, Central Java, are prepared to compete in global market. In order to realize that objective, batik products should fulfill some qualifications, one of which is “environmental friendliness”. As batik production is usually generating wastewater which pollutes the environment, the technology of wastewater treatment should be developed to solve the problem. This preliminary study has been done to assess the effectiveness of anaerobic baffled reactor (ABR) and rotating biological contactor (RBC) in batik wastewater treatment. In 40 days of treatment period, the ABR performance in reducing pollutants showed …

Physical Characterization And Desulfurization Of Biobriquette Using Calcium-Based Adsorbent, Mahidin Mahidin, Asri Gani, Khairil Khairil

Makara Journal of Technology

Combustion of coal and co-combustion of their co-fuel contribute to gas emissions. Among the gas emissions are SOx, NOx, CO and CO2. Introduction of calcium based adsorbent is addressed to absorb SO2 that release to the atmosphere during the combustion process. Objective of the research is at first to observe the physical characteristics of biobriquettes as a function of briquette compositions (coal to palm kernel shell ratios) and Ca/S ratios (Ca in adsorbent and S in briquette) using a natural adsorbent (shellfish waste). The second objective is to investigate desulfurization characteristics as a function of Ca/S ratios and desulfurization temperatures …

Medium Density Fibreboard Made Of Acetylated Sludge From Paper Mill, Luthfi Hakim, Evalina Herawati, I Nyoman Jaya Wistara

Makara Journal of Technology

Medium Density Fibreboard Made of Acetylated Sludge from Paper Mill. Research of using sludge as raw material for making medium density fibreboard (MDF) was useful to create additional value of sludge. The objective of the research was to evaluate physical properties, mechanical properties, and durability of MDF from acetylated sludge in 4 levels of acetate anhydride (0%, 3%, 5%, and 7%) with 3 replicates. The MDF was made using dry process. After materials were mixed with adhesives, they were pressed using hotpress under 170 oC temperature and 45 Pa pressure for 25 minutes. The size of the MDF sample was …

Cassava Pulp As A Biofuel Feedstock Of An Enzymatic Hydrolysis Proces, Djuma’Ali Djuma’Ali, Nonot Soewarno, Sumarno Sumarno, Dyah Primarini, Wahono Sumaryono

Makara Journal of Technology

Cassava pulp, a low cost solid byproduct of cassava starch industry, has been proposed as a high potential ethanolic fermentation substrate due to its high residual starch level, low ash content and small particle size of the lignocellulosic fibers. As the economic feasibility depends on complete degradation of the polysaccharides to fermentable glucose, the comparative hydrolytic potential of cassava pulp by six commercial enzymes were studied. Raw cassava pulp (12% w/v, particle sizeμm) hydrolyzed by both commercial pectinolytic (1) and amylolytic (2) enzymes cocktail, yielded 70.06% DE. Hydrothermal treatment of cassava pulp enhanced its susceptibility to enzymatic cleavageas compared to …

Alos/Palsar Image Processing Using Dinsar And Log Ratio For Flood Early Detection In Jakarta Based On Land Subsidences, Dodi Sudiana, Mia Rizkinia

Makara Journal of Technology

Flood that occurred in Jakarta is not only influenced by rainfall, urban planning system and drainage alone, but also may be involved land subsidence (LS). LS is possible in because Jakarta stands on top of layers of sediments and the presence of ground water consumption in very large quantities. In this research, the Advanced Land Observing Satellite (ALOS)/Phased Array type L-band Synthetic Aperture Radar (PALSAR) data was processed to determine the level of LS in Jakarta area and its relation to flood potential area. Differential interferometry method (DInSAR) was performed on two PALSAR data with different acquisition years, i.e. 2007 …

Analytical And Computational Simulation Approaches To Design Low Energy Glass Block, Floriberta Binarti, Agustinus Djoko Istiadji, Prasasto Satwiko, Priyo Tri Iswanto

Makara Journal of Technology

Analytical and Computational Simulation Approaches to Design Low Energy Glass Block. An environmentally friendly process was developed to produce a low embodied energy glass block from waste glasses. The energy efficiency of the glass block is represented by its thermal conductance (U)

Improvement Of High Temperature Oxidation Of Low Carbon Steel Exposed To Ethanol Combustion Product At 700 °C By Hot-Dip Aluminizing Coating, Mohammad Badaruddin

Makara Journal of Technology

Low carbon steel (AISI 1005) was coated by hot-dipping into a molten Al-10% Si bath at 700 °C for 18s. After hotdipping treatment, the coating layers consisted of Al, Si, FeAl3, τ5-Fe2Al8Si, and Fe2Al5. The bare steel and the aluminized steel were isothermally oxidized at 700 °C in ethanol combustion product at atmospheric pressure for 49 h. The aluminized steel shows good performance in high temperature oxidation because the formation of Al2O3 layer on the coating surface. The growth of iron oxide nodules on the surface coating was accelerated by rapid outward diffusion of Fe-ions due to the presence of …

Establishment Code Hand Palm (Palm Code) 2d Gabor-Based Method, I Ketut Gede Darma Putra, Wira Bhuana, Erdiawan Erdiawan

Makara Journal of Technology

Establishment Code Hand Palm (Palm Code) 2D Gabor-Based Method. Palmprint is relatively new in physiological biometrics. Palmprint ROI segmentation and feature extraction are two important issues in palm print recognition. This paper introduces two steps in the center of mass moment method for ROI segmentation that will be applied in the Gabor 2D filter to obtain palm code as palmprint feature vector. Normalized Hamming distance was used to measure the similarity degrees of two feature vectors of palmprint. The system was tested using database 1000 palmprint images generated from 5 samples from each of the 200 persons randomly selected with …

Flutter Analysis Of Rx-420 Balistic Rocket Fin Involving Rigid Body Modes Of Rocket Structures, Novi Andria

Makara Journal of Technology

Flutter Analysis of RX-420 Balistic Rocket Fin Involving Rigid Body Modes of Rocket Structures. Flutter is a phenomenon that has brought a catastrophic failure to the flight vehicle structure. In this experiment, flutter was analyzed for its symmetric and antisymmetric configuration to understand the effect of rocket rigid modes to the fin flutter characteristic. This research was also expected to find out the safety level of RX-420 structure design. The analysis was performed using half rocket model. Fin structure used in this research was a fin which has semispan 600 mm, thickness 12 mm, chord root 700 mm, chord tip …

Flexible Connection Elastomeric Rubber As A Pounding Resisting Element Between Two Adjacent Buildings, Yuskar Lase, James Jatmiko Oetomo

Makara Journal of Technology

Flexible Connection Elastomeric Rubber as a Pounding Resisting Element between Two Adjacent Buildings To solve pounding problem of two adjacent buildings, structural designer usually employs a dilatation between the structures or make the two structures as a monolith structure. Other alternative is by using an elastomeric rubber as a pounding resisting element between the two structures. Effectiveness in applying elastomeric rubber component as flexible connection of two adjacent structures is the main focus of this paper. Various simulations such as structure models, earthquake excitations and openings in gap element are studied. Observation of maximum structural responses will be performed for …

Optimation Of Nitrogen And Phosphorus In Azolla Growth As Biofertilizer, Hany Handajani

Makara Journal of Technology

Nitrogen is one of the most important minerals for living organisms. Azolla is known as a small water fern which can fix nitrogen through the symbiotic association with the blue green algae Anabaena. Experimental studies were carried out in the glass house, investigating the growth of Azolla using different levels of nitrogen and phosphorus in the media. The experiment used 12 treatments with 3 levels of nitrogen (0, 5, and 10 mg atom/L) and 4 levels of phosphorus (0, 10, 20, and 30 mg atom/l) in a factorial design with 3 replicates. The results show that the highest biomass for …

Application Of Principal Component Proximity Transform And Geostatistics Methods For Volume Shale Distribution As Reservoir Characreristic Imaging In Seismic 3d, Nur Islami

Makara Journal of Technology

Application of Principal Component Proximity Transform and Geostatistics Methods for Volume Shale Distribution as Reservoir Characreristic Imaging in Seismic 3D. Principal component proximity transform (PCPT) technique was used to predict the content of volume shale into seismic data in reservoir modeling framework. The goal in this research is to get the volume shale imaging in three dimensions and allow for reservoir modelling. The reservoir modelling requires an integrated quantitative and qualitative data sources collected separately, such as well and seismic data. Integrating PCPT and Geostatistic methods can generate the detail information for characterization of reservoir’s properties. Finally, it shows that …

Antibacterial Activity Of Papaya Leaf Extracts Against Pathogenic Bacteria, Elisa Friska Romasi, Jessica Karina, Adolf Jan Nexson Parhusip

Makara Journal of Technology

It was reported that the extracts of papaya leaves could inhibit the growth of Rhizopus stolonifer. Antibacterial activity of Carica papaya leaf extracts on pathogenic bacteria was observed in this study. Papaya leaves were extracted by using maceration method and three kinds of solvents: ethanol, ethyl acetate, and hexane. Papaya leaf extracts were tested against Bacillus stearothermophilus, Listeria monocytogenes, Pseudomonas sp., and Escherichia coli by agar diffusion method. The objectives of this study were to determine extract ability against pathogenic bacteria, to observe the influence of pH, NaCl, and heat on extracts ability, and to observe extract ability against B. …

Code Of Standard Practice For Cold-Formed Steel Structural Framing, 2011 Edition, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Effects Of Column Stiffness On Seismic Behavior Of Steel Plate Shear Walls, Xuhua Guo

Master's Theses

Steel plate shear walls (SPSWs) are a lateral force resisting system consisting of thin infill steel plates surrounded by boundary frame members. The infill steel plates are allowed to buckle in shear and subsequently form diagonal tension field actions during earthquake events. Hysteretic energy dissipation of this system is primarily achieved through yielding of the infill plates. Conceptually, in a SPSW system with ideally rigid columns pinned to ground, the infill plates at different stories will yield simultaneously as a result of the lateral loads. However, when the columns become flexible, infill plate yielding may initially occur at one story …

Extending Integral Concepts To Curved Bridge Systems, Saeed Eghtedar Doust

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The behavior of integral abutment systems and the extension of their application to curved bridges are investigated. First, the stresses in the elements of a typical integral abutment are studied by conducting nonlinear finite element analysis using the software package Abaqus. The results are design recommendations for the details of such abutments. The effect of integral abutments on the responses of bridges is also investigated. Steel and concrete bridge systems are studied separately.

The studied steel bridge systems are composed of composite I-girder superstructures and integral abutments supported on steel H-piles. A series of finite element studies for different bridge …

Seamless Bridge And Roadway System For The U.S. Practice, Nima Ala

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Expansion joints are one of the main causes for high maintenance costs in bridges. The search for ideal expansion joints has proven fruitless. That is why it has been said that “the best joint is no joint”. A seamless bridge system is envisioned that results in bridges with long service lives by eliminating the joints over the entire length of the bridge, approach slab and a segment of the roadway called transition. All bridge thermal movements are dissipated to zero in the transition. The system is similar to a system developed in Australia but modifications had to be made to …

Optimal Design Of Trusses With Geometric Imperfections: Accounting For Global Instability, Mehdi Jalalpour, Takeru Igusa, James K. Guest

Civil and Environmental Engineering Faculty Publications

A topology optimization method is proposed for the design of trusses with random geometric imperfections due to fabrication errors. This method is a generalization of a previously developed perturbation approach to topology optimization under geometric uncertainties. The main novelty in the present paper is that the objective function includes the nonlinear effects of potential buckling due to misaligned structural members. Solutions are therefore dependent on the magnitude of applied loads and the direction of resulting internal member forces (whether they are compression or tension). Direct differentiation is used in the sensitivity analysis, and analytical expressions for the associated derivatives are …

Post-Earthquake Reconnaissance Report On Transportation Infrastructure Impact Of The February 27, 2010, Offshore Maule Earthquake In Chile, Wen-Huei Phillip Yen, Genda Chen, Ian G. Buckle, Tony M. Allen, Daniel E. Alzamora, Jeffrey Ger, Juan G. Arias

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This report documents the findings and lessons learned from the February 27, 2010, M8.8 offshore Maule earthquake in Chile. Fewer than 0.15 percent of the bridges in Chile's inventory, most built after 1995, collapsed or suffered damage that rendered them useless. Many spans of precast prestressed discontinuous girder bridges with continuous decks fell off their supports, probably due to significant in-plane rotation of the superstructure as a result of severe shaking. Lateral steel stoppers used to provide both vertical and lateral restraints on girders were largely unsuccessful due to their inadequate connection detail to cap beams and abutments. Reinforced concrete …

China Earthquake Reconnaissance Report: Performance Of Transportation Structures During The May 12, 2008, M7.9 Wenchuan Earthquake, Wen-Huei Phillip Yen, Genda Chen, Mark Yashinski, Youssef M.A. Hashash, Curtis J. Holub, Kehai Wang, Xiaodong Guo

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This report documents the lessons learned from damage caused in the May 12, 2008, M7.9 earthquake in Wenchuan County, China. The damage to the 14 observed bridges reminded the researchers of damage suffered during the 1971 San Fernando Earthquake in California. The bridges had few seismic details such as long seats, large shear keys, or tightly spaced transverse reinforcement. Most arch and girder bridges collapsed due to surface rupturing of the seismic faults in the Longmen-Shan thrust zone. A significant portion of roadways and bridges were pushed away or buried by landslides in the steep slopes of mountainous terrain. Damage …

Performance Analysis Of Solar Walls In Minnesota: Final Project Report, Patrick A. Tebbe, Saeed Moaveni, Louis Schwartzkopf

Mechanical and Civil Engineering Department Publications

A study of unglazed transpired solar collectors (referred to as solar walls for this report), has been undertaken. Several installations in the Twin Cities, MN region have been identified, researched, and studied. A combination of weather stations, data logging systems, and building energy management systems were used to collect experimental data on four buildings. Performance calculations were then performed for these buildings and compared with various performance/modeling tools.

Accelerated Construction For Pedestrian Bridges: A Comparison Between High Strength Concrete (Hsc) And High-Strength Self Consolidating Concrete (Hs-Scc), John J. Myers, Kurt Bloch

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

High-strength concrete (HSC) and glass fiber reinforced polymer (GFRP) bars are materials utilized in bridge construction to lower cost, reduce construction time, and increase service life of bridge structures. Recently, high-strength self-consolidating concrete (HS-SCC), a highly flowable concrete that does not require vibration, has been developed as a viable alternative to HSC for use in situations with congested steel or a need for rapid construction. Coupling HS-SCC with GFRP bars could create durable structures built rapidly. Several performance related issues remain to be investigated such as the behavior of prestress loss, shear, creep, shrinkage, thermal gradients, mechanical property development, time …

Modern Protection Systems To Prevent Corrosion Of Structural Steel Elements Due To Deicing And Roadway Salts, John J. Myers, Wei Zheng

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The effectiveness of innovative polymeric coatings, polyurea and Poly aspartic polyurea, to protect structural steel from corrosion was investigated through standard laboratory tests. the coating evaluation tests included salt fog test, QUV weathering test, adhesion test, and freeze-thaw stability test. These tests were used to assess the long-term performance of coating technologies compared to the conventional polyurethane type coatings, i.e. coating systems with inorganic zinc primer, epoxy intermediate coat and polyurethane topcoat. This paper presents part of results in the aforementioned evaluation tests. the results illustrate that Poly aspartic coating systems are very promising for corrosion mitigation and can provide …