Aerospace Engineering Commons^™

Asteroid Retrieval Feasibility Study, John Brophy, Fred Culick, Louis Friedman, Pedro Llanos, Et Al.

Publications

This report describes the results of a study sponsored by the Keck Institute for Space Studies (KISS) to investigate the feasibility of identifying, robotically capturing, and returning an entire Near-Earth Asteroid (NEA) to the vicinity of the Earth by the middle of the next decade. The KISS study was performed by people from Ames Research Center, Glenn Research Center, Goddard Space Flight Center, Jet Propulsion Laboratory, Johnson Space Center, Langley Research Center, the California Institute of Technology, Carnegie Mellon, Harvard University, the Naval Postgraduate School, University of California at Los Angeles, University of California at Santa Cruz, University of Southern …

Aerodynamics Of An Aerofoil In Transonic Ground Effect: Numerical Study At Full-Scale Reynolds Numbers, G. Doig, T. J. Barber, A. J. Neely, D. D. Myre

Aerospace Engineering

The potential positive effects of ground proximity on the aerodynamic performance of a wing or aerofoil have long been established, but at transonic speeds the formation of shock waves between the body and the ground plane would have significant consequences. A numerical study of the aerodynamics of an RAE2822 aerofoil section in ground effect flight was conducted at freestream Mach numbers from 0·5 to 0·9, at a range of ground clearances and angles of incidence. It was found that in general the aerofoil's lifting capability was still improved with decreasing ground clearance up until the point at which a lower …

Section Abstracts: Aeronautical And Aerospace Sciences

Virginia Journal of Science

Abstracts of the Aeronautical and Aerospace Sciences Section for the 90th Annual Meeting of the Virginia Academy of Science, May 23-25, 2015. Norfolk State University, Norfolk, Virginia.

A Nanoporous Silicon Nitride Membrane Using A Two-Step Lift-Off Pattern Transfer With Thermal Nanoimprint Lithography, Bhargav P. Nabar, Zeynep Çelik-Butler, Brian H. Dennis, Richard E. Billo

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Nanoimprint lithography is emerging as a viable contender for fabrication of large-scale arrays of 5500 nm features. A fabrication process for the realization of thin nanoporous membranes using thermal nanoimprint lithography is presented. Suspended silicon nitride membranes were fabricated by low-pressure chemical vapor deposition (LPCVD) in conjunction with a potassium hydroxide-based bulk micromachining process. Nanoscale features were imprinted into a commercially available thermoplastic polymer resist using a prefabricated silicon mold. The pattern was reversed and transferred to a thin aluminum oxide layer by means of a novel two-stage lift-off technique. The patterned aluminum oxide was used as an etch mask …

Evaluating Network Analysis And Agent Based Modeling For Investigating The Stability Of Commercial Air Carrier Schedules, Sheila Ruth Conway

Engineering Management & Systems Engineering Theses & Dissertations

For a number of years, the United States Federal Government has been formulating the Next Generation Air Transportation System plans for National Airspace System improvement. These improvements attempt to address air transportation holistically, but often address individual improvements in one arena such as ground or in-flight equipment.

In fact, air transportation system designers have had only limited success using traditional Operations Research and parametric modeling approaches in their analyses of innovative operations. They need a systemic methodology for modeling of safety-critical infrastructure that is comprehensive, objective, and sufficiently concrete, yet simple enough to be deployed with reasonable investment. The methodology …

Engineering Innovation And Design For Stem Teachers And The Stem Quality Framework, James Rowley, Sandi Preiss, Margaret Pinnell, Suzanne Franco

Mechanical and Aerospace Engineering Faculty Publications

The backbone of economic growth in the United States relies on engineering innovation. However, engineering innovation cannot occur without engineers and scientists. Unfortunately however, many K-12 students do not have a good understanding of the engineering design process or the vast field of engineering. As a result, many students lose interest in math and science and do not pursue Science, Technology, Engineering and Math (STEM) fields. This paper will describe a unique partnership among the Teacher Education Program and School of Engineering at the University of Dayton (UD) and the Dayton Regional STEM Center (DRSC). This partnership initiated with the …

Near Earth Asteroid Mission Design For 2000 Sg344, Gökhan Çahşkan

Mechanical & Aerospace Engineering Theses & Dissertations

In this thesis, methodologies and capabilities for mission trajectory design to asteroid 2000 SG344 are investigated. Design of orbital trajectories for interplanetary space flight requires application of principles from orbital mechanics including three dimensional orbital element description, orbit propagation, asteroid ephemerides, targeting logic, relative motion dynamics, and numerical algorithm implementation. The thesis research will attempt to assemble and integrate these various topics to achieve a general capability to conduct asteroid mission trajectory design. Further, appropriate methodology including selection of assumptions and models, computation process and flow, and design metrics and trades to achieve a practical and effective trajectory design process …

Effect Of Emergent Technologies On Aircraft Fuel Burn By Seat Class, Lee Matthew Watkins

Mechanical & Aerospace Engineering Theses & Dissertations

In this research, a set of advanced technologies collectively referred to as N+2 technologies, are applied to representative aircraft for seven different seat classes. This study will give a better understanding of which technologies will benefit aircraft of differing sizes compared to current studies which have focused on the fuel efficiency benefits of the N+1 technologies for one size of aircraft. Technologies applied consist of hybrid wing body (HWB) platforms, boundary layer ingestion (BLI) engines, weight reducing technologies, hybrid laminar flow control (HLFC) and advanced engine technologies. The aircraft are modeled in Flight Optimization System (FLOPS), a program developed at …

Earth Observation Time Estimates Using Curve Fitted Perturbed Orbit Tracks, Taner Gundogdu

Mechanical & Aerospace Engineering Theses & Dissertations

In this thesis, time to observation for a generic perturbed low Earth orbit satellite, which is tasked, for reconnaissance of a given surface target is investigated. A curve fitting concept applied to past orbital track data is used to estimate and predict the overflight observation time. The least squares method is selected for the curve fitting process and used for both linear and non-linear aspects. Since orbital track data for actual spacecraft are not widely available, numerical integration of the governing motion equations is used as an alternate data source. One of the numerical integration methods, fourth-order Runge-Kutta, is used …

Dynamics And Control Of Satellite Relative Motion In Proximity Operations, Mohamed Elsayed Aly Abd Elaziz Okasha

Mechanical & Aerospace Engineering Theses & Dissertations

In this dissertation, the development of relative navigation, guidance, and control algorithms of an autonomous space rendezvous and docking system are presented. These algorithms are based on innovative formulations of the relative motion equations that are completely explicit in time. The navigation system uses an extended Kalman filter based on these formulations to estimate the relative position and velocity of the chaser vehicle with respect to the target vehicle and the chaser attitude and gyro biases. This filter uses the range and angle measurements of the target relative to the chaser from a simulated LIDAR system, along with the star …

De-Centralized And Centralized Control For Realistic Ems Maglev Systems, Mohamed M. Aly M. Moawad

Mechanical & Aerospace Engineering Theses & Dissertations

A comparative study of de-centralized and centralized controllers when used with real EMS Maglev Systems is introduced. This comparison is divided into two parts. Part I is concerned with numerical simulation and experimental testing on a two ton six-magnet EMS Maglev vehicle. Levitation and lateral control with these controllers individually and when including flux feedback control in combination with these controllers to enhance stability are introduced. The centralized controller is better than the de-centralized one when the system is exposed to a lateral disturbing force such as wind gusts. The flux feedback control when combined with de-centralized or centralized controllers …

Numerical Study Of The Performance Of A Model Scramjet Engine, Ayad Alhumadi

Mechanical & Aerospace Engineering Theses & Dissertations

A computational parametric investigation was conducted to study the effect of variations to several geometric parameters on the performance of a two-dimensional model scramjet engine (square cross section area for 3-D model). Geometric parameters included backstep location, height, and angle and fuel injector angle, diameter, and location. Two- and three-dimensional geometries have been studied, using a finite-volume computational fluid dynamics (CFD) code (FLUENT) with structured grids with sizes between 50,000 and 90,000 cells for the two-dimensional geometry and with structured hexahedral grid sizes between 650,000 and 949,725 cells for the three-dimensional geometry. Otherwise, identical values of program inputs were utilized …

Molecular Dynamics Studies On Nanoscale Gas Transport, Murat Barisik

Mechanical & Aerospace Engineering Theses & Dissertations

Three-dimensional molecular dynamics (MD) simulations of nanoscale gas flows are studied to reveal surface effects. A smart wall model that drastically reduces the memory requirements of MD simulations for gas flows is introduced. The smart wall molecular dynamics (SWMD) represents three-dimensional FCC walls using only 74 wall Molecules. This structure is kept in the memory and utilized for each gas molecule surface collision. Using SWMD, fluid behavior within nano-scale confinements is studied for argon in dilute gas, dense gas, and liquid states. Equilibrium MD method is employed to resolve the density and stress variations within the static fluid. Normal stress …

Peridynamic Model For Dynamic Fracture In Unidirectional Fiber-Reinforced Composites, Wenke Hu, Youn Doh Ha, Florin Bobaru

Department of Mechanical and Materials Engineering: Faculty Publications

We propose a computational method for a homogenized peridynamics description of fiber-reinforced composites and we use it to simulate dynamic brittle fracture and damage in these materials. With this model we analyze the dynamic effects induced by different types of dynamic loading on the fracture and damage behavior of unidirectional fiber-reinforced composites. In contrast to the results expected from quasi-static loading, the simulations show that dynamic conditions can lead to co-existence of and transitions between fracture modes; matrix shattering can happen before a splitting crack propagates. We observe matrix–fiber splitting fracture, matrix cracking, and crack migration in the matrix, including …

The Development Of A Force Balance For Testing Micro Aerial Vehicles, Michael Christopher King

Doctoral Dissertations and Master's Theses

The purpose of this work was to create a six degree of freedom balance that could produce meaningful data for micro aerial vehicles. Research was conducted to investigate the common balance configurations, and the strengths and weaknesses of each configuration were used to select the most appropriate design. The limitations of available fabrication facilities, the desired level of performance and the end user of the balance were all considered to finalize the design. The balance and data acquisition system were fabricated over a period of several months, and unforeseen design issues were handled forthwith. Rigorous calibration and testing processes were …

Design And Optimization Of A Deflagration To Detonation Transition (Ddt) Section, Francisco X. Romo

Doctoral Dissertations and Master's Theses

Throughout the previous century, hydrocarbon-fueled engines have used and optimized the `traditional' combustion process called deflagration (subsonic combustion). An alternative form of combustion, detonation (supersonic combustion), can increase the thermal efficiency of the process by anywhere from 20 - 50%. Even though several authors have studied detonation waves since the 1890's and a plethora of papers and books have been published, it was not until 2008 that the first detonation-powered flight took place. It lasted for 10 seconds at 100 ft. altitude. Achieving detonation presents its own challenges: some fuels are not prone to detonate, severe vibrations caused by the …

High-Fidelity Modeling Of Airfoil Interaction With Upstream Turbulence, Jacob Brodnick

Doctoral Dissertations and Master's Theses

To supplement past research on low speed unsteady airfoil responses to upstream disturbances, this work proposes and investigates a method to generate a turbulent momentum source to be convected downstream and interact with an SD7003 airfoil in a high-fidelity numerical simulation. A perturbation velocity field is generated from a summation of Fourier harmonics and applied to the forcing function in the momentum terms of the Navier Stokes Equations. The result is a three-dimensional, divergence-free, convected turbulent gust with applied statistical parameters. A parametric study has been done in 2D and 3D comparing the resultant flow fields and airfoil interactions for …

Increasing Reliability Of A Small 2-Stroke Internal Combustion Engine For Dynamically Changing Attitudes, Steven C. Crosbie

Theses and Dissertations

Remotely Piloted Aircraft (RPA) typically utilize commercial internal combustion engines (ICE) as their power sources. These engines are designed to run at sea level, but these aircraft are often pressed into service at higher altitudes where the performance characteristics deteriorate. A Brison 95cc two-stroke engine's performance characteristics at altitude are investigated using a test facility that can measure these characteristics over a range of pressures and temperatures. With its stock carburetor at sea level static (SLS) conditions, the engine makes 5.5 peak horsepower (hp) and brake specific fuel consumption (BSFC) ranged from 1.2-4.0 lb/(hp-hr). At 10,000 feet conditions, the peak …

Evaluation Of The Thorax Of Manduca Sexta For Flapping-Wing Micro Air Vehicle Applications, Alex C. Hollenbeck

Theses and Dissertations

The tobacco hornworm hawkmoth (Manduca sexta) provides an excellent model from which to garner knowledge pertaining to the development of a Flapping Wing Micro Air Vehicle (FWMAV). Insect-sized FWMAVs will be used by the future warfighter for reconnaissance, nuclear/chemical/biological hazard sensing, and targeting. One of the major challenges facing FWMAV developers is the energetically demanding nature of low Reynolds flapping flight. Investigating the Manduca sexta thorax/wing flapping mechanism as a mechanical system will provide insight into its inherent efficiency. This thesis examined the energetics of the thorax under static loading and dynamic loading using an innovative load-application technique. It was …

Aircraft Course Optimization Tool Using Gpops Matlab Code, Ryan D. Gauntt

Theses and Dissertations

Aircraft course planning between two points in a clear, no threat environment is easy and straightforward. However, the addition of various threats can greatly increase the difficulty and complexity of course planning. Placing new waypoints along the edge of each threat, mostly skirting the dangerous environment, may not prove too difficult, but such courses are far from optimal. Given aircraft, environment, and time constraints it is likely a much more optimal path exists between any given start and end points. This research focuses on determining the feasibility of using the General Pseudospectral Optimization Software program files written for the MATLAB …

Material Characterization For Composite Materials In Load Bearing Wave Guides, Gabriel Almodovar

Theses and Dissertations

This study will establish a methodology to examine samples of composite material for application in a load bearing waveguide. The composite material will operate in a specific frequency range for applications in small RPAs. A graphite epoxy stiffening component will be primarily considered. Different nickel, graphene, and carbon nanotube (CNT) coatings and films will be applied to the graphite epoxy. Tests will determine the material's radio frequency (RF) performance for application as an antenna/waveguide component. The study will use scattering (S) parameters determined from a network analyzer to collect these data. The S parameters will then be used to resolve …

Satellite Relative Motion Control For Mit's Spheres Program, Samuel P. Barbaro

Theses and Dissertations

Autonomous formation flight concepts and algorithms have great potential to revolutionize spacecraft operations enabling missions to perform autonomous docking, in-space refueling, in-space robotic assembly, and space debris removal. Such tasks require the implementation of speed and path control algorithms to maneuver satellites along relative paths with specified rates along those paths. This thesis uses MATLAB® and SIMULINK® to design and simulate a control algorithm capable of providing relative speed and path control between satellites with a pointing error of less than two degrees, a position error of less than two millimeters, and a millimeter per second of velocity error. The …

Cubesat Attitude Determination And Helmholtz Cage Design, Megan R. Brewer

Theses and Dissertations

A method of 3-axis satellite attitude determination utilizing six body-fixed light sensors and a 3-axis magnetometer is analyzed. A Helmholtz cage is designed, built, and tested to provide a dynamic, 3-axis, uniform magnetic field to cancel the Earth's magnetic field and create an environment similar to the geomagnetic field a satellite would experience on-orbit. A CubeSat is provided the inertial magnetic vector and Sun vector, which are combined with data from the light sensors and magnetometer in a CubeSat. Attitude is estimated on-board the CubeSat via the optimal fast quaternion estimation algorithm. The capabilities of the Helmholtz cage, including the …

Computational Analysis And Characterization Of Rc-135 External Aerodynamics, Michael G. Chenery

Theses and Dissertations

Both the RC-135V/W Rivet Joint (RJ) and the RC-135U Combat Sent (CS) aircraft are United States Air Force (USAF) electronics reconnaissance platforms. The RJ is the USAF's standard airborne signals intelligence (SIGINT) gathering platform, while the CS is designed to collect technical intelligence on adversary radar emitter systems. Both aircraft are extensively modified C-135's characterized by protruding cheek fairings along the sides of the fuselage forward of the wings as well as the addition of numerous antennas along the top and bottom of the fuselage. The major distinguishing feature between the two variants is the nose radome, wherein the RJ …

Gravitational Lens: Deep Space Probe Design, Berkley R. Davis

Theses and Dissertations

A number of interstellar precursor missions have been designed, but they have all made use of unproven future technologies. This research focuses on designing an interstellar precursor mission to the gravitational lens that can be manufactured solely with today's technology. The design includes an examination of trip time and trajectory, a system trade between subsystems, a launch vehicle analysis and an overall spacecraft performance analysis. The trip time was found to be approximately 108 years using the NEXT thruster and GPHS power source. The GPHS provided approximately 4 kW of power at BOL. The communications subsystem relied on a 12 …

Hybrid Solution Of Stochastic Optimal Control Problems Using Gauss Pseudospectral Method And Generalized Polynomial Chaos Algorithms, Gerald C. Cottrill

Theses and Dissertations

Two numerical methods, Gauss Pseudospectral Method and Generalized Polynomial Chaos Algorithm, were combined to form a hybrid algorithm for solving nonlinear optimal control and optimal path planning problems with uncertain parameters. The algorithm was applied to two concept demonstration problems: a nonlinear optimal control problem with multiplicative uncertain elements and a mission planning problem sponsored by USSTRATCOM. The mission planning scenario was constructed to find the path that minimizes the probability of being killed by lethal threats whose locations are uncertain to statistically quantify the effects those uncertainties have on the flight path solution, and to use the statistical properties …

Applications Of Aerodynamic Forces For Spacecraft Orbit Maneuverability In Operationally Responsive Space And Space Reconstitution Needs, Matthew N. Goodson

Theses and Dissertations

Each year multiple satellites are launched to provide end users key pieces of information. This information ranges from remote sensing data for military or civilian purposes (e.g., weather forecasting, troop movements, agricultural production, etc.) to large bandwidth telecommunications sensors. No matter the type of information needed, society is demanding more. Because of this continual rise in information needs, the current model of launching one satellite for one mission is not sustainable. To satisfy the information needs of nations across the globe, a means for satellites to transition from one mission type to another must be developed. One means of transitioning …

Conceptual Layout Of Wing Structure Using Topology Optimization For Morphing Micro Air Vehicles In A Perching Maneuver, James R. Elgersma

Theses and Dissertations

A topology optimization model for conceptual wing structure layouts of morphing micro air vehicles (MAVs) has been developed and implemented in MATLAB. Specifically, a six degree-of-freedom finite element (FE) model with a general quadrilateral discretization scheme was created by superposition of a known simple linear plane membrane element and a Kirchhoff plate bending element derived herein. The purpose of the six degree-offreedom model was to accommodate in-plane and out-of-plane aerodynamic loading combinations. The FE model was validated and the MATLAB implementation was verified with classical beam and plate solutions. A compliance minimization optimization objective was then formulated with the Solid …

Accurate Modeling Of Stability And Control Properties For Fighter Aircraft From Cfd, Jedediah H. Butler

Theses and Dissertations

Difficulties in obtaining accurate Stability and Control (S&C) data for nonlinear regions in the flight envelope early in the design phase often lead to costly fixes late in the acquisition process. Work examined herein addresses this problem by utilizing recent advances in Computational Fluid Dynamics (CFD) to create a high-fidelity database before any parts have to be physically produced. In combination with CFD, System Identification (SID) is used to characterize the S&C characteristics of aircraft by some Reduced Order Model (ROM). The method of obtaining enough data in the right places, via some optimized maneuver, to create an accurate ROM …

Cooling Requirements For The Ultra Compact Combuster, Donald D. Johnson

Theses and Dissertations

Over the past several years, AFIT and the Air Force Research Laboratory have collaboratively investigated a novel combustor system that is compact in design and has potential use in an inter-turbine burner system. The ultra-compact combustor (UCC) design wraps the combustion section circumferentially around the axial core flow and exploits the use of high-g combustion. The combustor's volume and weight are reduced by integrating the exit compressor vane and the turbine inlet vane. This creates a new hybrid vane that resides directly below the circumferential combustor. Recently, a computational effort to understand the fundamental aspects of the UCC on a …