Aerospace Engineering Commons^™

Numerical Study Of Nutrient Mixing In Trabecular Bone In Microgravity, Disuse And Normogravity, Sagar Gharti

Doctoral Dissertations and Master's Theses

Mechanical loading is known to regulate bone remodeling by driving interstitial fluid flow which stimulates cells and drives nutrient transport within the trabecular network. In microgravity, the absence of mechanical stimulation or loading suppresses convective flow processes, causing diffusion-driven nutrient mixing and renewal, and accelerated bone loss. This thesis investigates how oscillation frequency and trabecular bone density jointly control nutrient mixing and wall shear stress within trabecular cavities.

A computational fluid dynamics (CFD) framework is developed in STAR-CCM+ using a soft-cap oscillation model that mimics cyclic compression. Three idealized trabecular morphologies are simulated across different frequencies to represent microgravity or …

Slender And Nonslender Delta Wing Simulation And Analysis, Aashish Gyawali, Brinda Bhattarai, Nishesh Bista, Sundeep Rao Dr

Journal of Aviation Technology and Engineering

Stability, controllability, and maneuverability are critical factors for aircraft with short takeoff and landing distances, such as modern fighter aircraft and unmanned aerial vehicles. Delta wings are commonly employed in these aircraft due to their efficient aerodynamics, enabling high maneuverability, and performance at both low and high speeds. Nonslender wings are used for low-speed performance and agility, while slender wings offer reduced drag and are suited for high-speed operations. In flight, an aircraft encounters different airflow patterns including vortices that circulate from the higher-pressure lower side of the wing to the lower-pressure upper side, contributing to lift generation. However, as …

An Inquiry Into The Physics Of Mixing And Floc Filtration, Andrew P. Pennock

Dissertations

Flocculation and clarification are two essential processes to deliver safe water at a reasonable cost to consumers. There are two major thrusts to the research presented in this dissertation. The first is to better characterize the physics and mixing parameters used for the design of hydraulic flocculators in the context of drinking water treatment plants. The second major thrust is to investigate floc filtration as a mechanism for the removal of primary particles during floc blanket clarification.

The intensity of mixing in environmental and chemical engineering applications is often characterized by the Camp and Stein velocity gradient. This parameter has …

Optimization Of The Cross-Section Of Generic Flexible Bridges, Manal Kamal Zaki, Mina M. Helmy, Mark M. Tawadros

Journal of Engineering Research

This paper investigates the behavior of flexible bridges prone to aerodynamic instabilities due to wind. Optimal cross-sections that reduce aerodynamic forces are recommended. This is achieved by studying a variety of bridge sections with different widths of upper and lower sloping edges in addition to studying the upper and lower cramps of the deck. The wind velocities are also parameterized. Computations are developed based on the powerful computational fluid dynamics (CFD) method known as FLUENT and embedded in ANSYS software. For parametric study, a design of experiments (DOE) is performed based on the response surface methodology (RSM) combined with the …

Computational Study Of Detonation Wave Propagation And Propellant Injection In Detonation Engines, Jayson C. Small

Mechanical and Aerospace Engineering Dissertations - Archive

This research investigates the physics of detonation waves and their application to detonation engines, with two primary objectives: (1) to characterize detonation wave propagation, specifically detonation speed and wavefront thickness, in stoichiometric propane-oxygen mixtures near quenching conditions, and (2) to examine the physiochemical processes during propellant injection under detonation engine conditions, focusing on flush-wall-mounted, fluidic-valve injectors.

A multi-fidelity computational approach was employed. Reduced-order modeling based on the Chapman–Jouguet and Zeldovich–von Neumann–Doring models were used to evaluate detonation parameters and select an appropriate chemical mechanism. High-fidelity, multi-dimensional simulations solved the unsteady, compressible, reacting flows with finite-rate chemistry, using Reynolds-Averaged Navier–Stokes equations …

Multiphysics Modeling And Experimental Validation Of High-Strength Steel In Laser Powder Bed Fusion Process, M. Rangapuram, S. Babalola, J. W. Newkirk, L. N. Bartlett, F. W. Liou, K. Chandrashekhara, Stephen R. Cluff

Materials Science and Engineering Faculty Research & Creative Works

Laser powder bed fusion (LPBF) is a subset of the additive manufacturing process in which a laser beam selectively joins the metal powder into a desired part in a sequential layer process. Owing to its complex nature of rapid heating and cooling of the melt pool, there is a need to understand the melt pool behavior and its effects on the final manufactured part. a densely packed powder bed is highly desirable for fabricating a superior part using the LPBF process. in this work, discrete element model was used to generate powder beds with realistic powder properties and various factors …

Bi-Modal Excitation Of A Supersonic Rectangular Jet, Benjamin Malczewski

Doctoral Dissertations and Master's Theses

This work addresses the issue of supersonic rectangular jet noise via bi-modal excitation. A Mach 1.5 heated rectangular jet with a 2:1 aspect ratio is considered. Theoretical work is presented in which a Reduced-Order Model (ROM) is used in conjunction with the Linearized Euler Equations to predict the nonlinear growth and decay of various frequencies due to the interaction between harmonically related modes and the mean flow. Scope is limited to a symmetric disturbance. The case of no interaction is used to help identify a dominant coherent structure, referred to as “f”. For the symmetric disturbance, a Strouhal number of …

Computational Fluid Dynamics Visualization For Unmanned Aerial Systems In Bridge Inspections, Kristoffer B. Borgen, John Mott

Journal of Aviation Technology and Engineering

Bridge inspections are an expensive and time-consuming process, varying significantly with a bridge’s style, height, width, and length. Inspections create interruptions that interfere with bridge use, as the examination requires partial or total closure, causing traffic delays. Unmanned aerial system (UAS) use has increased significantly over the past decade, including assistance and coordination during bridge inspections. However, the impact on a UAS from high winds and turbulent airflows induced by a bridge’s structure can decrease flight safety during inspections. Visualization of these hazards is difficult for UAS operators; therefore, a process to estimate the velocity and locations of these hazardous …

Investigation On The Effects Of Biofouling On The Boundary Layer, Adam N. Bacon

LSU New Orleans Theses and Dissertations

This study is an investigation of the effect of biofouling on the boundary layer of a flat plate and a NACA 4-digit series foil. Three identical hydrofoils made of resin were placed in the Gulf of Mexico at Grand Isle, Louisiana, and observed and analyzed by marine biologists at the University of New Orleans for their species composition. The resulting biofouling that grew was primarily made up of barnacles and bryozoans. The foils were submerged in an open channel flume at zero incidence and subjected to a series of experiments whose arc-length Reynolds numbers ranged from approximately 13000 to 32000. …

Performance Effects Of Dissociated Hydrogen In Nuclear Thermal Propulsion Engines, Richard Adam Gorrell

UNLV Theses, Dissertations, Professional Papers, and Capstones

Nuclear thermal propulsion (NTP) research considers hydrogen dissociation as negligible to design and analysis of propulsion engines. This study reintroduces chemically reacting flow to NTP engine analysis for investigation of the dissociation effect on engine performance. A first-principles approach observes the basic chemical mechanism and reaction within the high-speed, high-temperature NTP flow to baseline expected atomic hydrogen levels and validate equilibrium. A surface reaction study looks into hydrogen absorption through dissociation and its effect on the boundary layer, and bulk flow. For total performance, the resulting dissociated flow is analyzed through nozzle expansion and performance metrics calculated.

All historic reactor …

Aerodynamic Design And Analysis Of A Modified 2006 Mazda Miata, William N. Recher

Honors College Theses

Aerodynamic forces developed by automobiles have destabilizing effects at high speed. These forces tend to skew toward a vehicle’s rear which can present safety concerns, especially for rear-wheel-drive automobiles like the Mazda Miata. To address oversteer and high-speed instability, a vehicle’s design can be tailored to bring about aerodynamic balance and improve traction. LiDAR was used to bring the physical automobile into the digital space. Then, a splitter and diffuser were added to reduce the magnitude of the destabilizing forces. Next, the size and shape of the rear-wing required to balance the vehicle was calculated using a combination of parameters …

Numerical Simulation And Optimization Of Fin Configurations For Enhanced Heat Sink Performance In Aluminum And Copper Materials, Rimpy Singh

Mechanical and Aerospace Engineering Theses - Archive

The constant evolution of data centers and high-power electronic systems has raised critical challenges in heat dissipation and thermal management. Single-phase immersion cooling, where electronic components are submerged in a thermally conductive but non-electrically conductive liquid (dielectric liquid), offers improved heat dissipation capabilities and emerges as a promising alternative to traditional air-cooling methods, which often fail to meet the thermal demands of densely packed, high-power systems. This study investigates and compares the thermal performance of aluminum and copper heat sinks with fin thicknesses of 0.33 mm and 0.54 mm, respectively, using finite element analysis based on computational fluid dynamics (CFD) …

Aeroelastic Phenomena Of Fixed-Wing Aircraft In Transonic And Supersonic Flows Using A Tightly-Coupled Computational Approach, John C. Havenar

College of Graduate Studies: Theses & Dissertations

Aeroelastic phenomena encountered during flight have considerable effects on the aerodynamic characteristics of fixed-wing aircraft. Transonic aeroelastic phenomena are often characterized by unique flow features which have complex ramifications for aircraft in transonic flight. Computational study of high-speed aeroelastic phenomena requires a fully-coupled aeroelastic algorithm. A series of wing designs are studied with a computational finite volume method solver accompanied by a finite element method solver for the calculation of structural deformation. The computational model for the flow field is validated with experimental data. Modeled flight conditions include transonic flows with bordering subsonic and supersonic cases included for completeness. The …

Numerical Study Of Owls' Leading-Edge Serrations, Asif Shahriar Nafi, Nikolaos Beratlis, Elias Balaras, Roi Gurka

Physics and Engineering Science

Owls' silent flight is commonly attributed to their special wing morphology combined with wingbeat kinematics. One of these special morphological features is known as the leading-edge serrations: rigid miniature hook-like patterns found at the primaries of the wings' leading-edge. It has been hypothesized that leading-edge serrations function as a passive flow control mechanism, impacting the aerodynamic performance. To elucidate the flow physics associated with owls' leading-edge serrations, we investigate the flow-field characteristic around a barn owl wing with serrated leading-edge geometry positioned at 20° angle of attack for a Reynolds number of 40 000. We use direct numerical simulations, where …

Experiments And Simulations Of Liquid Mass Gauging And Slosh Dynamics In Microgravity, Jedediah Morse Storey

Theses and Dissertations

Advancements in liquid propellant management science and technologies are key to increasing safety, decreasing cost, and increasing payload mass of space missions. Propellant usually comprises a large portion of the total mass of launch vehicles and spacecraft, so liquid propellant sensing, as well as predicting and controlling the motion of it, are important. Electrical Capacitance Tomography (ECT) is an emerging sensing technology that is capable of measuring the distribution of liquid anywhere inside of a tank, potentially making it useful for measuring slosh and gauging mass. An ECT-instrumented tank was successfully tested in microgravity for the first time. Basics of …

Jet Noise Reduction: A Fresh Start, Christopher K. Tam, Fang Q. Hu

Mathematics & Statistics Faculty Publications

Attempts to reduce jet noise began some 70 years ago. In the literature, there have been many publications written on this topic. By now, it is common knowledge that jet noise consists of a number of components. They possess different spectral and radiation characteristics and are generated by different mechanisms. It appears then that one may aim at the suppression of the noise of a single component instead of trying to reduce jet noise overall. The objective of the present project is to reduce large turbulence structures noise. It is the most dominant noise component radiating in the downstream direction. …

Mitigation Of Aeroacoustic Noise Of A Fixed Wing Using Passive Flow Control, Cameron L. Perry

College of Graduate Studies: Theses & Dissertations

As the world becomes more environmentally conscious, noise pollution is of increasing concern. In this study, shallow dimples are applied to a NACA 0012 airfoil at multiple angles of attack (AoA) with the intent of reducing aeroacoustic noise emissions. Both Reynolds Averaged Navier-Stokes (RANS) and Large Eddy Simulation (LES) models are used for aerodynamic and aeroacoustic investigations, respectively, at a fixed Reynolds number of 4.8 x 10⁵. Altering the dimple depth to diameter ratio (d/D) from 2.5% to 15% is first investigated, with a d/D of 5% or lower resulting in the least aerodynamic impact. The transition from …

Analysis Of Propeller Designs Focusing On Lowering Sound Pressure Level Through Reduced Tip Loading, Luca A. Zeitvogel

Theses and Dissertations

This research focused on potential design optimizations for small propellers. Designs sought to reduce noise generated without sacrificing efficiency by “unloading” the propeller tip by reducing angle of attack near the tip. To see if nearfield performance improvements translated to a reduction in farfield sound pressure level, farfield experimental acoustic testing was performed on propellers that had been measured experimentally in the nearfield. The farfield results provided limited insight due to an equipment malfunction during testing. However, a large data set was obtained, which provides opportunities for future analyses. A computational simulation sought to recreate some of the nearfield experiments …

Machine Learning In Aerodynamic Shape Optimization, Jichao Li, Xiaosong Du, Joaquim R.R.A. Martins

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Machine learning (ML) has been increasingly used to aid aerodynamic shape optimization (ASO), thanks to the availability of aerodynamic data and continued developments in deep learning. We review the applications of ML in ASO to date and provide a perspective on the state-of-the-art and future directions. We first introduce conventional ASO and current challenges. Next, we introduce ML fundamentals and detail ML algorithms that have been successful in ASO. Then, we review ML applications to ASO addressing three aspects: compact geometric design space, fast aerodynamic analysis, and efficient optimization architecture. In addition to providing a comprehensive summary of the research, …

Fuel Injector Design Of A Hypersonic Jet Engine Using Computational Fluid Dynamics, Melissa Rose Mercado

UNLV Theses, Dissertations, Professional Papers, and Capstones

The development of hypersonic airbreathing engines, such as a supersonic combustion ramjet, or scramjet, are implemented for flight Mach numbers over 5 where combustion must occur in supersonic conditions. The advancement of scramjet propulsion has led to favored usage over rocket propulsion systems for in atmosphere applications due to their lighter weight, higher specific impulse, and greater maneuverability [1]. The combustor section of a scramjet engine houses the fuel injectors. Fuel is injected into the supersonic flow with the main objective of achieving rapid and thorough fuel-air mixing because the residence time in the combustion chamber has a timescale of …

A Study Of Asymmetric Supersonic Wind Tunnel Nozzle Design, Brittany A. Davis

Mechanical & Aerospace Engineering Theses & Dissertations

Achieving higher Mach numbers for private and commercial flight is a growing interest in the aerospace community. To qualify vehicles prior to flight, tests must be run in wind tunnels. Asymmetric wind tunnel nozzles are of continuing interest to the aerospace community due to their ability to change throat geometry, allowing for a range of Mach numbers to be achieved that encompasses all of the supersonic regime. The sliding block wind tunnel at Old Dominion University (ODU) is designed for a range of Mach numbers from about 1.8 to 3.5 but is limited to an upper limit of 2.8 by …

A Numerical Study Of Water Entry Problems Based On Overset Meshes, Yanni Chang

Mechanical and Aerospace Engineering Dissertations - Archive

A series of numerical experiments carried out on the water entry of circular cylinders are presented in this study. A cylinder was entering into the water with a prescribed inclined angle and velocity. The interface between water and air is tracked by the Piecewise Linear Interface Calculation (PLIC) schemes in conjunction with the Volume of Fluid (VOF) method. PLIC schemes have been extensively employed in the VOF method for interface capturing in numerical simulations of multiphase flows. Dynamic overset meshes, which have been widely used for problems with relative motions and complex geometric shapes, are applied to handle the moving …

Development And Applications Of Adjoint-Based Aerodynamic And Aeroacoustic Multidisciplinary Optimization For Rotorcraft, Ramiz Omur Icke

Mechanical & Aerospace Engineering Theses & Dissertations

Urban Air Mobility (UAM) is one of the most popular proposed solutions for alleviating traffic problems in populated areas. In this context, the proposed types of vehicles mainly consist of rotors and propellers powered by electric motors. However, those rotary-wing components can contribute excessively to noise generation. Therefore, a significant noise concern emerges due to urban air vehicles in or around residential areas. Reducing noise emitted by air vehicles is critically important to improve public acceptance of such vehicles for operations in densely populated areas.

Two main objectives of the present dissertation are: (1) to expand the multidisciplinary optimization to …

Optimizing Design Parameters For Active Flow Control Boundary-Layer Fence Performance Enhancement On A Delta Wing, Nathan L. Tedder

Theses and Dissertations

Utilizing computational fluid dynamic (CFD) simulations, the presented study is able to further the investigation of replicating and improving upon the performance of a NACA 0012 cropped half-span delta-wing at high angles-of-attack with an active flow control fluidic fence via wall-normal, steady blowing from an optimized single chordwise slot located at z/b = 70%,. The data is generated using CREATE-AV Kestrel v10.1rc5 CFD software on the Department of Defense High Performance Computing systems. The flight regime is held constant at a Mach number of 0.18 and a Reynolds number (Re) of 5.0 x 10⁵, based on the root …

Parallel Anisotropic Unstructured Grid Adaptation, Christos Tsolakis, Nikos Chrisochoides, Michael A. Park, Adrien Loseille, Todd Michal

Computer Science Faculty Publications

Computational fluid dynamics (CFD) has become critical to the design and analysis of aerospace vehicles. Parallel grid adaptation that resolves multiple scales with anisotropy is identified as one of the challenges in the CFD Vision 2030 Study to increase the capacity and capability of CFD simulation. The study also cautions that computer architectures are undergoing a radical change, and dramatic increases in algorithm concurrency will be required to exploit full performance. This paper reviews four different methods to parallel anisotropic grid adaptation. They cover both ends of the spectrum: 1) using existing state-of-the-art software optimized for a single core and …

Using Numerical Modeling To Determine Viscous Losses Within Helium Turbomachinery, Benjamin Uhlig

Mechanical and Aerospace Engineering Theses - Archive

As the consumption of energy has increased relentlessly over the last few decades, the need for reliable clean energy generation has increased as well. Currently, nuclear power is the only method capable of providing a stable supply of clean energy, although the nuclear energy generation process still requires improvement. Specifically, there is a need to increase efficiencies while reducing the risks of radioactive contamination. It is possible that both these issues may be mitigated using helium as the working fluid. However, the performance of turbomachinery using helium must be evaluated before its use can be implemented. To do this, Balaji …

Fluid Flow Analysis Of Low-Altitute Agricultural Uav Pesticide Spraying Device, Dan Han

Student Works (2020-2029)

The nozzle is an important part of the drone pesticide spraying device. The quality of the nozzle directly affects the atomization performance. Fan nozzles are widely used in the field of plant protection in agriculture, forestry, pest control, and weed removal. When using drones to spray pesticides, the spraying velocity, the spraying range of the pesticides, and the atomized particle size are all key factors that directly affect the efficiency of pesticide use. This paper uses SOLIDWORKS and ANSYS software to design and simulate. The boundary conditions are kept the same, and the influence of the nozzle's grooving angle (α), …

Helios And Tenasi Results For The Workshop For Integrated Propeller Prediction, Aaron Crawford

Honors Theses

Beginning in 2018, the AIAA began the workshop for integrated propeller prediction. This effort was intended to bolster the CFD prediction capabilities of the aerospace community due to a resurgent interest in propeller driven vehicles for electric applications. The test bed for this workshop is the NASA X-57, a model of which was experimentally tested in the Lockheed Martin Low Speed Wind Tunnel in January 2019. Using the 3D scanned geometry provided by the workshop a mesh was created and all priority one simulations were performed using two flow solvers. The flow solvers used were Helios, developed by the ADD …

A Numerical Investigation Of Microgravity Evaporation, Daniel Peter Ringle

Dissertations and Theses

Evaporation is important to myriad engineering processes such as cooling, distillation, thin film deposition, and others. In fact, NASA has renewed interest in using cabin air pressure evaporation as a means to recycle waste water in space. As one example, NASA recently conducted experiments aboard the International Space Station (ISS) to measure evaporation rates in microgravity and to determine the impacts of porous structure on the process. It has long been assumed that differences in evaporation rates between 1-g₀ and microgravity are small. However, discrepancies by as much as 40% have been observed in practice. The assumption now …

Design And Analysis Of A Disk-Oriented Engine Combustor, Bennett M. Staton

Theses and Dissertations

In a novel approach to gas-turbine power production, an engine was designed and analyzed to use both a single-stage centrifugal compressor and single-stage radial in- ow turbine configured back-to-back. This air path reduced the axial length of the engine up to 60%, providing additional modularity in a gas-turbine engine that could be used to improve mobility of ground-based power units or increase the survivability of aircraft through the use of distributive propulsion. This increased modularity was made possible by the use of a circumferential ow combustor that substantially decreased the axial length of the burner and negated the need to …