Aerospace Engineering Commons^™

Desensitizing Flame Structure And Exhaust Emissions To Flow Parameters In An Ultra-Compact Combuster, Adam K. Parks

Theses and Dissertations

A major thrust of turbine engine research is to improve both efficiency and thrust-to-weight ratio of the engine. A promising solution to this challenge is the Ultra-Compact Combustor (UCC). The UCC shortens the axial length of the combustor by performing combustion circumferentially on the outer diameter of the engine. The reduction in axial length yields significant weight savings and increases the thrust-to-weight ratio. The design also increases combustion efficiency by performing the combustion in a centrifugally loaded environment which allows unreacted particles to remain in the combustor sufficiently long enough to become combustion products. The Air Force Institute of Technology …

A Finite Element Analysis Of A Carbon Fiber Composite Micro Air Vehicle Wing, Theodore A. Szelag

Theses and Dissertations

Micro-air vehicles (MAV)s provide a valuable and low observable way to do the jobs that the Air Force deems to be dull, dirty and dangerous. Basing the design of an MAV wing on that of a biological counterpart will provide a proven design that is capable of achieving the mission requirements. This research is designed to analyze the design and manufacturing of a wing based off the Manduca Sexta.

Inaccuracies in the fiber orientation can result in substantial changes in the material properties. Experimental vibration data of composite material samples manufactured using a three-ply [0/90/0] small non-homogenous fiber composite provided …

Empirical Characterization Of Unconstrained Tape Spring Deployment Dynamics, Daniel M. Williams

Theses and Dissertations

Satellite cost and mission capability are very sensitive to mass requirements. Mass or volume savings in one component will either lower total spacecraft mass, or provide greater margin for design error in other components. Solar arrays and antennas in particular are often driven by launch vehicle volume constraints instead of mission needs. Deployable structures provide more on-orbit area for both solar arrays and antennas, while occupying less space during launch. These structures therefore, help address these constraints and have been proven as efficient solutions for many years. Tape springs are one example in this category of structures which offer greater …

Trajectory Control And Optimization For Responsive Spacecraft, Costantinos Zagaris

Theses and Dissertations

The concept of responsive space has been gaining interest, and growing to include systems that can be re-tasked to complete multiple missions within their lifetime. The purpose of this study is to develop an algorithm that produces a maneuver trajectory that will cause a spacecraft to arrive at a particular location within its orbit earlier than expected. The time difference, delta t, is used as a metric to quantify the effects of the maneuver. Two separate algorithms are developed. The first algorithm is an optimal control method and is developed through Optimal Control Theory. The second algorithm is a feedback …

Integration Of Cold Atom Interferometry Ins With Other Sensors, Aaron J. Canciani

Theses and Dissertations

Inertial navigation systems (INS) using cold-atom interferometry are currently under development, and sensors in these systems are expected to be several orders of magnitude more ccurate than current navigation grade sensors. This signi cant increase in accuracy motivates the need to explore how these high accuracy inertial navigation systems can be integrated with other sensors. This research focuses on methods of integrating cold atom interferometry INS with conventional navigation grade INS, as well as with GPS. Results from a full 6 degree of freedom simulation show that integrating CAI INS with navigation grade INS is a successful way to address …

Modeling, Simulation, And Flight Test For Automatic Flight Control Of The Condor Hybrid-Electric Remote Piloted Aircraft, Christopher Giacomo

Theses and Dissertations

This thesis describes the modeling and verification process for the stability and control analysis of the Condor hybrid-electric Remote-Piloted Aircraft (HE-RPA). Due to the high-aspect ratio, sailplane-like geometry of the aircraft, both longitudinal and lateral/directional aerodynamic moments and effects are investigated. The aircraft is modeled using both digital DATCOM as well as the JET5 Excel-based design tool. Static model data is used to create a detailed assessment of predictive flight characteristics and PID autopilot gains that are verified with autonomous flight test. PID gain values were determined using a six degree of freedom linear simulation with the Matlab/SIMULINK software. Flight …

Enhanced Image-Aided Navigation Algorithm With Automatic Calibration And Affine Distortion Prediction, Juan D. Jurado

Theses and Dissertations

This research aims at improving two key steps within the image aided navigation process: camera calibration and landmark tracking. The camera calibration step is improved by automating the point correspondence calculation within the standard camera calibration algorithm, thereby reducing the required time for calibration while maintaining the output model accuracy. The feature landmark tracking step is improved by digitally simulating affine distortions on input images in order to calculate more accurate feature descriptors for improved feature matching in high relative viewpoint change. These techniques are experimentally demonstrated in an outdoor environment with a consumer-grade inertial sensor and three imaging sensors, …

Development And Testing Of A Rotating Detonation Engine Run On Hydrogen And Air, Jason C. Shank

Theses and Dissertations

Rotating detonation engines (RDEs) have the potential for greater efficiencies over conventional engines by utilizing pressure gain combustion. A new modular RDE (6 in diameter) was developed and successfully run on hydrogen and standard air. The RDE allows for variation of injection scheme and detonation channel widths. Tests provided the operational space of the new RDE as well as characterized detonation unsteadiness. It was found that a smaller equivalence ratio than previous was required to obtain continuous detonations. Also discovered was VCJ was reached in the RDE, but not sustained.

Integration, Testing And Validation, Of A Small Hybrid-Electric Remotely-Piloted Aircraft, Joseph K. Ausserer

Theses and Dissertations

Parallel hybrid-electric technology offers a wide variety of new mission capabilities including low-observable loiter operations and increased fuel efficiency for small remotely-piloted aircraft. This research focused on the integration, validation, and testing of a hybrid-electric propulsion system consisting of commercially available components to fabricate a small remotely-piloted aircraft capable of extended low-observable operation. Three novel aspects contributed to the success of the design: optimization of the propulsive components to the integrated system, torque control of the components for additive power, and a one-way bearing/ pulley mechanism (patent pending) mechanically linking the hybrid system components. To the knowledge of the author …

Determination Of Effective Crossover Location And Dimensions For Branched Detonation In A Pulsed Detonation Engine, Louis A. Camardo Ii

Theses and Dissertations

A study is presented of the optimal crossover duct location and width to obtain consistent branched detonation transition from one detonation tube to another. On a Pulsed Detonation Engine (PDE) with detonation branching, the duct location at which the detonation crosses from one (primary) tube to a branched (secondary) tube impacts the number of successful detonations. In this paper, a comparison is made of the effects of the location and width of the crossover duct for hydrogen, ethylene and an n-alkane. The crossover location is varied from the aft end of the detonation tube to the middle of the detonation …

Impact Of Trench And Ramp Film Cooling Designs To Reduce Heat Release Effects In A Reacting Flow, Michael R. Delallo

Theses and Dissertations

Increasing combustor fuel-air ratios are a recent area of concern in gas turbine film cooling due to the potential for heat release on the surface of film-cooled components. This investigation compared four different cooling designs on their heat release potential: namely fanned, normal and radial trenched, and ramped. Measurements of heat flux to the downstream surface, when subjected to a reacting mainstream flow, provide a qualitative comparison between the four tested configurations. Furthermore, this work studied the effect of multiple injection points in series along the surface of a flat plate. An upstream set of normal holes and an upstream …

Validation Of The Chemistry Module For The Euler Solver In Unified Flow Solver, William C. Humphrey Jr.

Theses and Dissertations

In the world of computational fluid dynamics (CFD), three main types of flow regimes exist: continuum, rarified, and free molecular. Of these regimes, the rarified regime is the most difficult to model because the continuum equations don't apply and using the Boltzmann equation is too computationally expensive to use. The Unified Flow Solver (UFS) is currently being developed to solve this problem by using the kinetic continuum Euler equations where valid, and only using the Boltzmann equation where necessary, thus reducing the computational cost. The use of the kinetic Euler equations helps to aid in the coupling of the Euler …

Methane Dual Expander Aerospike Nozzle Rocket Engine, Michael D. Moen

Theses and Dissertations

The Air Force Institute of Technology (AFIT), working to meet requirements set by the Air Force Research Laboratory's Next Generation Engine (NGE) initiative, is developing upper stage rocket models. The current path of investigation focuses on combining a dual expander cycle with an aerospike nozzle, or the Dual Expander Aerospike Nozzle (DEAN) using methane fuel. The design process will rely heavily on AFIT's previous work, which focused on the development of tools for and the optimization of a hydrogen/oxygen DEAN engine. The work outlined in this paper expands the existing research by substituting methane for hydrogen. The targets derived from …

Application Of Multi-Input Multi-Output Feedback Control For F-16 Ventral Fin Buffet Alleviation Using Piezoelectric Actuators, Tomoyuki D. Ono

Theses and Dissertations

Control of structural vibrations has been a popular topic. Use of MFC piezoelectric actuators and co-located sensors allows for an active rather than passive control method. The F-16 ventral fin is susceptible to buffet induced vibrations and is a perfect test structure for active vibration control for flight-testing. The research follows the previous ACTIVE FIN project and improves on the design by increasing the number of actuator layers, available actuator power, and using multi-input multi-output (MIMO) control algorithms. The research involved experimental identification of the ventral fin and its principle strain directions, selection of system components, determination of mathematical plant …

Development Of A Star Tracker-Based Reference System For Accurate Attitude Determination Of A Simulated Spacecraft, Jorge G. Padro

Theses and Dissertations

The goal of this research effort is to investigate the analysis, design, integration, testing, and validation of a complete star tracker and star field simulator system concept for AFIT's satellite simulator, SimSat. Previous research has shown that while laboratory-based satellite simulators benefit from star trackers, the approach of designing the star field can contribute significant error if the star field is generated on a flat surface. To facilitate a star pattern that better represents a celestial sky, a partially hemispherical dome surface is suspended above SimSat and populated with a system of light emitting diodes of various intensities and angles …

Creep Of Hi-Nicalon S Ceramic Fiber Tows At Elevated Temperature In Air And In Steam, Benjamin R. Steffens

Theses and Dissertations

Structural aerospace components require materials to have superior long-term mechanical properties that can withstand severe environmental conditions, such as high temperatures, high pressures and moisture, whilst enduring the loads they are designed for. Ceramic-matrix composites (CMCs) are capable of maintaining excellent strength and creep resistance at high temperatures, which make them attractive candidate materials for aerospace applications, particularly in propulsion. Silicon Carbide (SiC) ceramic fibers have been used as constituent materials in CMCs, although oxidation of the SiC to SiO₂ has been a known degredation mechanism. Recently developed near stoichiometric SiC fibers have shown significant improvements in thermochemical stability; …

Reynolds Number Effects On Thrust Coefficients And Piv For Flapping Wing Micro Air Vehicles, John P. Tekell

Theses and Dissertations

For the last several years the Air Force Institute of Technology (AFIT) has conducted research in aerodynamics for flapping wing micro air vehicles (MAVs). The focus of this research was to augment this effort by measuring thrust, velocity, and torque in tanks of water and glycerin using a scale and a reaction torque cell. The results for different flapping mechanisms are compared to a rotating propeller with the goal of elucidating the design trade space between rotorcraft and flapping wings at Reynolds numbers less than 100,000. In addition, flow visualization and quantitative velocity data were captured in the wake of …

Characterization Of Centrifugally-Loaded Flame Migration For Ultra-Compact Combustors, Kenneth D. Lebay

Theses and Dissertations

The Air Force Research Laboratory (AFRL) has designed an Ultra Compact Combustor (UCC) showing viable merit for significantly reducing gas turbine combustor length making it a viable candidate for implementation as an inter-turbine burner and realization of efficiency benefits from the resulting near constant temperature cycle. This concept uses an off-axis combustor cavity and projects approximately 66% length reduction over a conventional combustor. The annular nature of the cavity creates high angular acceleration levels, on the order of 500-3500 g's, resulting in strong centrifugal and buoyant forces. This unique combination works to significantly reduce the required burn time and subsequently …

Boundary Layer Measurements In The Trisonic Gas-Dynamics Facility Using Particle Image Velocimetry With Co₂ Seeding, Daniel B. Wolfe

Theses and Dissertations

Particle image velocimetry (PIV) is utilized with solid carbon dioxide (CO₂) seeding material to conduct boundary layer measurements in the test section of the Air Force Research Laboratory's Trisonic Gas-dynamics Facility (TGF), which has a 24 inch by 24 inch cross-section. Freestream velocity was set at Mach 0.3, Mach 0.5, or Mach 0.8 while stagnation pressure ranged from 500 to 2400 pounds per square foot (psf). High pressure liquid CO₂ was directed through expansion nozzles into shroud tubes which led to solidified particles in the wind tunnel stagnation chamber. Two different sets of shroud tubes were used …

Build Up And Operation Of An Axial Turbine Driven By A Rotary Detonation Engine, Jonathan R. Tellefsen

Theses and Dissertations

Detonation combustors provide advantages over current deflagration combustors due to their pressure gain and simplicity of design. Rotary detonation engines (RDEs) offer advantages over pulsed detonation engines (PDEs) due to a steadier exhaust and fewer total system losses. All previous research on turbine integration with detonation combustors has focused on utilizing PDEs to drive axial and centrifugal turbines. The objective of this thesis was the integration and testing of an axial turbine driven by a rotary detonation engine (RDE) to determine turbine operability. In pursuit of this objective, convergent nozzle sections were placed on the RDE to simulate the back-pressurization …

Plume Characterization Of Busek 600w Hall Thruster, Duc Minh Bui

Theses and Dissertations

The BHT-600W thruster has a high potential to place on various commercial and military satellites as a main propulsion system for orbit maintenance and orbit maneuvering. Therefore, the thruster's performance characteristics and parameters were evaluated for various operating conditions. These parameters include thrust, power consumption, mass flow rate, and efficiencies. Various plume properties were measured and characterized for the thruster to include exhaust beam profile and ion species distribution. The faraday probe was used to examine the thruster plume current density while the ion species fractions were determined by the ExB probe. The inverted pendulum thrust stand was also utilized …

Space Science Research And Stem Activities At Morehead State University, Robert J. Twiggs

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint presentation created by Professor Bob Twiggs titled "Space Science Research and STEM Activities at Morehead State University" from March 7, 2012.

Arliss: A Rocket Launch For International Student Satellites - Launch Report For 2011, David Raimondi

Robert "Bob" Twiggs STEM Education Collection

A report written by David Raimondi titled "ARLISS A Rocket Launch for International Student Satellites Launch Report for 2011" from March 7, 2012.

An Adjoint Method To Determine The Effective Material Properties Of An Ablator, Emma Johnstone

Ablation Workshop

The determination of the effective thermal properties of a material from thermocouple data has always been very labour intensive. Similarly determining the Arrhenius parameters for a decomposition model from thermo-gravimetric analysis is also very time-consuming. There is little formalisation of the procedures used to determine the material properties. Despite the fact that some effort has been devoted to this topic in the literature, it is not clear whether comparable effective material properties data would result if several groups used the same experimental data. The FGE Ablation code FABL has been written in an adjoint form and has successfully been used …

Ultrasonic Thermometry For Recession Measurements In Ablative Materials, Joseph A. Lloyd, Donald E. Yuhas

Ablation Workshop

Recent developments in ultrasonic instrumentation & sensors, improved signal processing, and high speed data acquisition have rekindled interest in ultrasonic thermometry and made temperature localization feasible and economically attractive to a wider range of applications. Ultrasound-based temperature measurements offer several advantages: they are non-intrusive, have high temporal response, isolate the sensor from explosive or chemically harsh environments and do not adversely influence thermal transport. Ultrasonic thermometry techniques rely on precise measurements of ultrasonic time-of-flight (ToF) which forms the basis for many applications including measurements of flow, heat flux, temperature, ablation and strain. In this report, we characterize the ultrasonic propagation …

A Statistics-Based Material Property Analysis To Support Ablation Simulation Uq Efforts, Sean R. Copeland, Juan Alonso, Milad Mahzari, Ioana Cozmuta

Ablation Workshop

Accurate characterization of entry capsule heat shield material properties is a critical component in modeling and simulating Thermal Protection System (TPS) response in a prescribed aerothermal environment. The thermal decomposition of the TPS material during the pyrolysis and charring processes is typically poorly characterized and results in large uncertainties in material properties as inputs for ablation models. These material property uncertainties contribute to large design margins on flight systems and cloud re-construction efforts for data collected during flight and ground testing, making revision to existing models for entry systems more challenging. This work focuses on the following areas of interest …

Efficient Uncertainty Quantification & Sensitivity Analysis For Hypersonic Flow And Material Response Simulations Under Inherent And Model-Form Uncertainties, Serhat Hosder

Ablation Workshop

Accurate numerical prediction of coupled hypersonic flow fields and ablative TPS material response is challenging due to the complex nature of the physics. The uncertainties associated with various physical models used in high-enthalpy hypersonic flow and material response simulations can have significant effects on the accuracy of the results including the heat-flux and temperature distributions in various layers of ablating TPS material. These uncertainties can arise from the lack of knowledge in physical modeling (model-form or epistemic uncertainty) or inherent variations in the model inputs (aleatory or probabilistic uncertainty). It is important to include both types of uncertainty in the …

Ablative Thermal Protection System (Tps) Margin Study, Steven Rickman, Lawrence Green, Brian Remark, Stan Bouslog, Jeremy Vander Kam, Mohammad Khalessi

Ablation Workshop

Predicting the reliability of the heat shield for crewed space vehicles has been a topic of continuing interest within NASA for many years. The design of a thermal protection system (TPS) is subject to numerous large sources of uncertainty and reliability assessments of such TPS are rare. The proposed talk discusses both the application of Design Of Experiments (DOE) to developing a new arc jet testing campaign for a given TPS and the reliability assessment conducted for the same TPS for a crewed space capsule (similar to Apollo capsules) to withstand re-entry to earth from space.

The objectives of the …

Electromagnetic Railgun Safety, Sven Ericson

Aerospace Engineering

The Cal Poly Electromagnetic Railgun is a system that with the proper precautions can be safely operated. Changes in plugs and boxes insure that the systems cannot be improperly wired, reducing the chances of accidental discharge. By covering exposed wires the system is safe to store as long as the voltage is checked before any maintenance is performed. Updates in procedures remove the possibility of injury to personnel and allow the railgun to be fired repeatedly under similar circumstances. Defined roles for the operators’ decreases confusion and allows people to concentrate on their area during testing. As hardware changes it …

Simulation Of Blood Flow And Nanoparticle Transport In A Stenosed Carotid Bifurcation And Pseudo-Arteriole, Graham Doig, Guan H. Yeoh, Victoria Timchenko, Gary Rosengarten, Tracie J. Barber, Sherman C.P. Cheung

Aerospace Engineering

Numerical simulation of flow through a realistic bifurcated carotid artery geometry with a stenosis has been conducted for comparison to experimental measurements. The behaviour of simplified therapeutic nanoparticles in relatively low concentration was observed using a discrete particle approach. The role of size (diameters from 500 nm to 50 nm) in determining particle residence time and the potential for both desirable and undesirable wall interactions was investigated. It was found that mean particle residence time reduced with decreasing particle diameter, and the percentage of particles experiencing one or more wall interactions increased simultaneously. Further simulations were conducted on a scaled-down …