Nanoscience and Nanotechnology Commons^™

Review Of Electrochemical And Electrodischarge Machining, Kamlakar P. Rajurkar, M. M. Sundaram, A. P. Malshe

Department of Mechanical and Materials Engineering: Faculty Publications

Electrochemical and electro-discharge machining processes are the two major electro-machining processes with unique capabilities. Electrical Discharge Machining (EDM) and Electrochemical Machining (ECM) offer a better alternative or sometimes the only alternative in generating accurate 3-D complex shaped macro, micro and nano features and components of difficult–to-machine materials. Technological advances reported in electrochemical and electro discharge machining processes, which reflect the state of the art in academic and industrial research and applications, are briefly reviewed in this paper.

Wire Electro-Discharge Machining Of Titanium Alloy, Farnaz Nourbakhsh, Kamlakar P. Rajurkar, Ajay P. Malshe, Jian Cao

Department of Mechanical and Materials Engineering: Faculty Publications

This paper presents an experimental investigation of wire electro-discharge machining (WEDM) of titanium alloy. The objective is to investigate the effect of seven process parameters including pulse width, servo reference voltage, pulse current, and wire tension on process performance parameters (such as cutting speed, wire rupture and surface integrity). A Taguchi L18 design of experiment (DOE) has been applied. All experiments have been conducted using Charmilles WEDM. It was also found that the cutting speed increases with peak current and pulse interval. Surface roughness was found to increase with pulse width and decrease with pulse interval. The Analysis of Variance …

Selective Detection And Automated Counting Of Fluorescently-Labeled Chrysotile Asbestos Using A Dual-Mode High-Throughput Microscopy (Dm-Htm) Method, Myoung-Ock Cho, Hyo Mi Chang, Donghee Lee, Yeon Gyu Yu, Hwataik Han, Jung Kyung Kim

Department of Mechanical and Materials Engineering: Faculty Publications

Phase contrast microscopy (PCM) is a widely used analytical method for airborne asbestos, but it is unable to distinguish asbestos from non-asbestos fibers and requires time-consuming and laborious manual counting of fibers. Previously, we developed a high-throughput microscopy (HTM) method that could greatly reduce human intervention and analysis time through automated image acquisition and counting of fibers. In this study, we designed a dual-mode HTM (DM-HTM) device for the combined reflection and fluorescence imaging of asbestos, and automated a series of built-in image processing commands of ImageJ software to test its capabilities. We used DksA, a chrysotile-adhesive protein, for selective …

Photovoltaic Device, Jinsong Huang, Bin Yang, Yongbo Yuan

Department of Mechanical and Materials Engineering: Faculty Publications

An apparatus includes a substrate; and a photoactive layer disposed on the substrate. The photoactive layer includes an electron acceptor material; an electron donor material; and a material having dipoles.

Scaling Of The Coercive Field In Ferroelectrics At The Nanoscale, R. V. Gaynutdinov, M. Minnekaev, S. Mitko, A. L. Tolstikhina, A. Zenkevich, Stephen Ducharme, Vladimir M. Fridkin

Stephen Ducharme Publications

The scaling of the coercive field in ferroelectric films at the nanoscale is investigated experimentally. The scaling in the films of copolymer vinylidene fluoride and BaTiO3 with thickness equal by the order of value to the critical domain nucleus size 1–10 nm reveals deviation from the well-known Kay–Dunn law. At this thickness region coercive field does not depend on thickness and coincides with Landau–Ginzburg–Devonshire value.

Subwavelength Surface Plasmons Based On Novel Structures And Metamaterials, Ruoxi Yang

Theses

With the rapid development of nanofabrication technology and powerful computational tools over the last decade, nanophotonics has enjoyed tremendous innovation and found wide applications in ultrahigh-speed data transmission, sensitive optical detection, manipulation of ultra-small objects, and visualization of nanoscale patterns. Surface plasmon-based photonics (or plasmonics) merges electronics and photonics at the nanoscale, creating the ability to combine the superior technical advantages of photonics and electronics on the same chip. Plasmonics focuses on the innovation of photonic devices by exploiting the optical property of metals. In particular, the oscillation of free electrons, when properly driven by electromagnetic waves, would form plasmon-polaritons …

A Dna Computer For Glioblastoma Multiforme Diagnosis And Drug Delivery, Sumaiya F. Hashmi

CMC Senior Theses

Glioblastoma multiforme (GBM) is a debilitating malignant brain tumor with expected patient survival of less than a year and limited responsiveness to most treatments, often requiring biopsy for diagnosis and invasive surgery for treatment. We propose a DNA computer system, consisting of input, computation, and output components, for diagnosis and treatment. The input component will detect the presence of three GBM biomarkers: vascular endothelial growth factor (VEGF), caveolin-1α (CAV), and B2 receptors. The computation component will include indicator segments for each of these genes, and ensure that output is only released if all the biomarkers are present. The output component …

Lanthanum Halide Nanoparticle Scintillators For Nuclear Radiation Detection, Paul Guss, Ronald Guise, Ding Yuan, Sanjoy Mukhopadhyay, Robert O’Brien, Daniel Robert Lowe, Zhitao Kang, Hisham Menkara, Vivek V. Nagarkar

Mechanical Engineering Faculty Research

Nanoparticles with sizesscintillators, in order to determine the viability of using scintillators employing nanostructured lanthanum trifluoride. Preliminary results of this investigation are consistent with the idea that these materials have an intrinsic response to nuclear radiation that may be correlated to the energy of the incident radiation.

Transparent Actuator Made With Few Layer Graphene Electrode And Dielectric Elastomer, For Variable Focus Lens, Taeseon Hwang, Hyeok-Yong Kwon, Joon-Suk Oh, Jung-Pyo Hong, Seung-Chul Hong, Youngkwan Lee, Hyouk Ryeo Choi, Kwang J. Kim, Mainul Hossain Bhuiya, Jae Do Nam

Mechanical Engineering Faculty Research

A transparent dielectric elastomer actuator driven by few-layer-graphene (FLG) electrode was experimentally investigated. The electrodes were made of graphene, which was dispersed inN-methyl-pyrrolidone. The transparent actuator was fabricated from developed FLG electrodes.The FLG electrode with its sheet resistance of 0.45 kΩ/sq (80 nm thick) was implemented to mask silicone elastomer. The developed FLG-driven actuator exhibited an optical transparency of over 57% at a wavenumber of 600 nm and produced bending displacement performance ranging from 29 to 946 μm as functions of frequency and voltage. The focus variation was clearly demonstrated under actuation to study its application-feasibility in …

Stochastic Charge Transport In Multi-Island Single-Electron Tunneling Devices, Madhusudan A. Savaikar

Dissertations, Master's Theses and Master's Reports - Open

The physics of the operation of singe-electron tunneling devices (SEDs) and singe-electron tunneling transistors (SETs), especially of those with multiple nanometer-sized islands, has remained poorly understood in spite of some intensive experimental and theoretical research. This computational study examines the current-voltage (IV) characteristics of multi-island single-electron devices using a newly developed multi-island transport simulator (MITS) that is based on semi-classical tunneling theory and kinetic Monte Carlo simulation. The dependence of device characteristics on physical device parameters is explored, and the physical mechanisms that lead to the Coulomb blockade (CB) and Coulomb staircase (CS) characteristics are proposed.

Simulations using …

Influence Of Surface Modification On Properties And Applications Of Complex Engineered Nanoparticles, Binghui Wang

Theses and Dissertations--Chemical and Materials Engineering

Complex engineered nanoparticles (CENPs) are being used on various applications. Their properties are different from those of neat nanoparticles. The dissertation explores these differences from four aspects: 1) Modify carbon nanomaterials’ inert surfaces and investigate the effect on thermal and rheological behavior of their dispersions; 2) Generate self-assembly bi-layer structure of oxide nanoparticles via surface modification; 3) Study interaction between lysozyme and different surface-charged ceria nanoparticles; 4) Investigate the biodistribution and transformations of CENPs in biological media.

An environment-friendly surface modification was developed to modify surfaces of carbon nanomaterials for increasing their affinity to non-polar fluid. It can offset formation …

Charge And Discharge Behaviour Of Li-Ion Batteries At Various Temperatures Containing Licoo2 Nanostructured Cathode Produced By Ccso, Y. Y. Mamyrbayeva, R. E. Beissenov, Mkhitar A. Hobosyan, S. E. Kumekov, Karen S. Martirosyan

Physics & Astronomy Faculty Publications

There are technical barriers for penetration market requesting rechargeable lithium-ion battery packs for portable devices that operate in extreme hot and cold environments. Many portable electronics are used in very cold (-40 °C) environments, and many medical devices need batteries that operate at high temperatures. Conventional Li-ion batteries start to suffer as the temperature drops below 0 °C and the internal impedance of the battery increases. Battery capacity also reduced during the higher/lower temperatures. The present work describes the laboratory made lithium ion battery behaviour features at different operation temperatures. The pouch-type battery was prepared by exploiting LiCoO2 cathode material …

Ecotoxicological Assessment Of Silica And Polystyrene Nanoparticles Assessed By A Multitrophic Test Battery, Maria Casado-Gavalda, Ailbhe Macken, Hugh Byrne

Articles

The acute ecotoxicity of different diameters of silica and polyethyleneimine polystyrene (PS-PEI)nanoparticles (NPs)was assessed on a test battery of aquatic organisms representing different trophic levels. Daphnia magna, Thamnocephalus platyurus, Pseudokirchneriella subcapitata and Vibrio fischeri, were employed in a series of standard acute ecotoxicity tests and work was complemented with two cytotoxicological end points on a rainbow trout gonadal cell line (RTG-2). Physico-chemical characterization of the NPs was performed in the different test media employed, using dynamic light scattering (DLS) and zeta potentiometry. In contrast to silica NPs exposure, for which no effect was observed for concentrations up …

Development Of Novel Nano-Composite Membranes As Introduction Systems For Mass Spectrometers: Contrasting Nano-Composite Membranes And Conventional Inlet Systems, Luis Miranda

USF Tampa Graduate Theses and Dissertations

This dissertation presents the development of novel nano-composite membranes as introduction systems for mass spectrometers. These nano-composite membranes incorporate anodic aluminum oxide (AAO) membranes as templates that can be used by themselves or modified by a variety of chemical deposition processes. Two types of nano-composite membranes are presented. The first nano-composite membrane has carbon deposited within the pores of an AAO membrane. The second nano-composite membrane is made by coating an AAO membrane with a thin polymer film. The following chapters describe the transmission properties these nano-composite membranes and compare them to conventional mass spectrometry introduction systems. The nano- composite …

Application And Characterization Of Self-Assembled Monolayers In Hybrid Electronic Systems, Michael Enoch Celesin

USF Tampa Graduate Theses and Dissertations

In this study, we explore ultra-thin insulators of organic and inorganic composition and their potential role as high-speed rectifiers. Typical applications for these structures include IR sensing, chemical detection, high speed logic circuits, and MEMS enhancements. While there are many elements in the functional group required to create a rectifying antenna (rectenna), the primary thrust of this work is on the rectifier element itself.

To achieve these research goals, a very good understanding of quantum tunneling was required to model the underlying phenomenon of charge conduction. The development of a multi-variable optimization routine for tunneling prediction was required. MATLAB was …

Magnetization Dynamics And Related Phenomena In Nanostructures, Sayan Chandra

USF Tampa Graduate Theses and Dissertations

Collective magnetic behavior in nanostructures is a phenomenon commonly observed in various magnetic systems. It arises due to competing inter/intra–particle interactions and size distribution and can manifest in phenomena like magnetic freezing, magnetic aging, and exchange bias (EB) effect. In order to probe these rather complex phenomena, conventional DC and AC magnetic measurements have been performed along with radio–frequency transverse susceptibility (TS) measurements. We also demonstrate the magnetic entropy change as a parameter sensitive to subtle changes in the magnetization dynamics of nanostructures. The focus of this dissertation is to study the collective magnetic behavior in core-shell nanostructures of Fe/γ–Fe …

Reactive Self-Heating Model Of Aluminum Spherical Nanoparticles, Karen S. Martirosyan, Maxim Zyskin

Physics & Astronomy Faculty Publications

Aluminum-oxygen reaction is important in highly energetic and high pressure generating systems. Recent experiments with nanostructured thermites suggest that oxidation of aluminum nanoparticles occurs in a few microseconds. Such rapid reaction cannot be explained by a conventional diffusion-based mechanism. We present a rapid oxidation model of a spherical aluminum nanoparticle, using Cabrera-Mott moving boundary mechanism, and taking self-heating into account. In our model, electric potential solves the nonlinear Poisson equation. In contrast with the Coulomb potential, a “double-layer” type solution for the potential and self-heating leads to enhanced oxidation rates. At maximal reaction temperature of 2000 C, our model predicts …

Characterising The Deformation Behaviour Of Human Tooth Enamel At The Microscale, Simona O'Brien

Theses: Doctorates and Masters

Enamel plays an important role in tooth function. Optimal combinations of composition and structure endow enamel with unique mechanical properties that remain largely unexplored. Specifically, more detailed understanding of the loadbearing ability of enamel is needed to mimic it synthetically and to design next generation biocomposite materials. This research investigates the variables that influence deformation behaviour of tooth enamel in relation to its hierarchical structure. Initially, a new method was developed for preparing flat, finely polished tooth samples that were maintained in their normal hydrated state for nanoindentation testing. In contrast to conventional methods, which commonly utilise either inappropriate or …

Electrochemical Performance Of Screen-Printed Composite Coatings Of Conducting Polymers And Carbon Nanotubes On Titanium Bipolar Plates In Aqueous Asymmetrical Supercapacitors, Xiaohang Zhou, George Z. Chen

Journal of Electrochemistry

Composites of conducting polymers (polypyrrole and polyaniline) with acid treated multi-walled carbon nanotubes were formulated into printable aqueous inks, with the aid of functional additives (benzethonium chloride as a surfactant with or without polyvinyl alcohol as a binder). The inks were screen-printed as fairly uniform coatings of various mass loading densities and areas (up to 75 mg cm^-2 and 100 cm²) on thin titanium plates (0.1 mm in thickness). These screen-printed plates were used to fabricate both unit cell and multi-cell stack of asymmetrical supercapacitors with screen-printed negative electrodes of activated carbon (pigment black) in aqueous electrolytes …

Electrocatalytic Activity Of Palladium Nanocatalysts Supported On Carbon Nanoparticles In Formic Acid Oxidation, Jie Huang, Zhiyou Zhou, Yang Song, Xiongwu Kang, Ke Liu, Wancheng Zhou, Shaowei Chen

Journal of Electrochemistry

Palladium nanostructures were deposited onto carbon nanoparticle surface by a chemical reduction method. Transmission electron microscopic studies showed that whereas the resulting metal-carbon (Pd-CNP) nanocomposites exhibited a diameter of 20 to 30 nm, the metal components actually showed a cauliflower-like surface morphology that consisted of numerous smaller Pd nanoparticles (3 to 8 nm). Electrochemical studies showed that the effective surface area of the Pd-CNP nanoparticles was about 40% less than that of Pd black, possibly because the Pd nanoparticles were coated with a layer of carbon nanoparticles; yet, the Pd-CNP nanocomposites exhibited marked enhancement of the electrocatalytic activity in formic …