Nanoscience and Nanotechnology Commons^™

The Role Of Oxygen In The Uptake Of Deuterium In Lithiated Graphite, C. N. Taylor, J. Dadras, Kara E. Luitjohan, Jean P. Allain, P. S. Kristic, C. H. Skinner

Birck and NCN Publications

We investigate the mechanism of deuterium retention by lithiated graphite and its relationship to the oxygen concentration through surface sensitive experiments and atomistic simulations. Deposition of lithium on graphite yielded 5%-8% oxygen surface concentration and when subsequently irradiated with D ions at energies between 500 and 1000 eV/amu and fluences over 10(16) cm(-2) the oxygen concentration rose to between 25% and 40%. These enhanced oxygen levels were reached in a few seconds compared to about 300 h when the lithiated graphite was allowed to adsorb oxygen from the ambient environment under equilibrium conditions. Irradiating graphite without lithium deposition, however, resulted …

Limit For Thermal Transport Reduction In Si Nanowires With Nanoengineered Corrugations, Sean E. Sullivan, Keng-Hua Lin, Stanislav Avdoshenko, Alejandro Strachan

Birck and NCN Publications

Non-equilibrium molecular dynamics simulations reveal that the thermal conductance of Si nanowires with periodic corrugations is lower than that of smooth wires with cross-sections equivalent to the constricted portions. This reduction in conductance is up to 30% and tends to plateau with increasing corrugation height. Spatially resolved temperature and heat current maps provide a microscopic understanding of this effect; we find that 80% of the heat current is carried through the constricted area even for high-amplitude corrugations. More importantly, we show that temperature gradient inversion and heat current vortices at the ridge peaks establish fundamental limits on maximum conductance reduction. …

Homogeneous Algan/Gan Superlattices Grown On Free-Standing (1(1)Over-Bar00) Gan Substrates By Plasma-Assisted Molecular Beam Epitaxy, Jiayi Shao, Dmitri N. Zakharov, Collin Edmunds, Oana Malis, Michael J. Manfra

Birck and NCN Publications

Two-dimensional and homogeneous growth of m-plane AlGaN by plasma-assisted molecular beam epitaxy has been realized on free-standing (1 (1) over bar 00) GaN substrates by implementing high metal-to-nitrogen (III/N) flux ratio. AlN island nucleation, often reported for m-plane AlGaN under nitrogen-rich growth conditions, is suppressed at high III/N flux ratio, highlighting the important role of growth kinetics for adatom incorporation. The homogeneity and microstructure of m-plane AlGaN/GaN superlattices are assessed via a combination of scanning transmission electron microscopy and high resolution transmission electron microscopy (TEM). The predominant defects identified in dark field TEM characterization are short basal plane stacking faults …

Friction And Wear Of Polytetrafluoroethylene/Graphene Oxide Composite Thin Films, Justin Kyle Carter

Graduate Theses and Dissertations

Polytetrafluoroethylene (PTFE) is a commonly used solid lubricant due to its low coefficient of friction and chemical inertness. As a polymer, PTFE suffers from high wear and low adhesion to substrates limiting its use as a thin film. Thin PTFE films are ideal candidates for solid lubrication in micro-machines and bearing applications. The main goal of this work is to enhance the durability of thin PTFE films through the addition of few layered graphene oxide (GO) as filler. In order to address adhesion issues, the addition of an adhesive layer of polydopamine (PDA) between stainless steel substrates and thin PTFE …

Near-Infrared Surface-Enhanced Fluorescence Using Silver Nanoparticles In Solution, Michael D. Furtaw

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Fluorescence spectroscopy is a widely used detection technology in many research and clinical assays. Further improvement to assay sensitivity may enable earlier diagnosis of disease, novel biomarker discovery, and ultimately, improved outcomes of clinical care along with reduction in costs. Near-infrared, surface-enhanced fluorescence (NIR-SEF) is a promising approach to improve assay sensitivity via simultaneous increase in signal with a reduction in background. This dissertation describes research conducted with the overall goal to determine the extent to which fluorescence in solution may be enhanced by altering specific variables involved in the formation of plasmonactive nanostructures of dye-labeled protein and silver nanoparticles …

Assessing Different Zeolitic Adsorbents For Their Potential Use In Kr And Xe Separation, Breetha Alagappan

UNLV Theses, Dissertations, Professional Papers, and Capstones

Separation of Kr from Xe is an important problem in spent nuclear fuel fission gas management. The energy intensive and expensive cryogenic distillation method is currently used to separate these gases. In this thesis, we have carried out the research into appropriate sorbents for the separation of Kr and Xe using pressure swing adsorption. We have examined zeolites using gas adsorption studies as they have the potential to be more cost effective than other sorbents. Zeolites are microporous aluminosilicates and have ordered pore structures. The pores in zeolites have extra-framework cations are substantially free to move. The mobility of cations …

An Integrated Multidisciplinary Nanoscience Concentration Certificate Program For Stem Education, Karen S. Martirosyan, Mikhail M. Bouniaev, Malik Rakhmanov, Ahmed Touhami, Nazmul Islam, Davood Askari, Tarek Trad, Dmitri Litvinov, Sergey E. Lyshevski

Physics & Astronomy Faculty Publications

Integration of nanoscience and nanotechnology curricula into the College of Science, Mathematics, and Technology (CSMT) at the University of Texas at Brownsville (UTB) is reported. The rationale for the established multidisciplinary Nanoscience Concentration Certificate Program (NCCP) is to: (i) develop nanotechnology-relevant courses within a comprehensive Science, Engineering and Technology curriculum, and, to offer students an opportunity to graduate with a certificate in nanoscience and nanotechnology; (ii) to contribute to students' success in achieving student outcomes across all college's majors, and, improve the breath, depth and quality of science, technology, engineering and mathematics (STEM) graduates' education; (iii) through NCCP, recruit certificate- …

Zinc Oxide Nanorod Based Ultraviolet Detectors With Wheatstone Bridge Design, Arun Vasudevan

Graduate Theses and Dissertations

This research work, for the first time, investigated metal semiconductor-metal (MSM) zine oxide (ZnO) nanorod based ultra-violet (UV) detectors having a Wheatstone bridge design with a high

responsivity at room temperature and above, as well as a responsivity that was largely independent of the change in ambient conditions. The ZnO nanorods which acted as the sensing element of the detector were grown by a chemical growth technique. Studies were conducted to determine the effects on ZnO nanorod properties by varying the concentration of the chemicals used for the rod growth. These studies showed how the rod diameter and the deposition …

Ergonomichandle And Articulating Laparoscopictool, M. Susan Hallbeck, Dmitry Oleynikov, Kathryn Done, Tim Judkins, Allison Dimartino, Jonathan Morse, Lawton N. Verner

Department of Mechanical and Materials Engineering: Faculty Publications

The present invention relates to a laparoscopic apparatus. The apparatus includes a handle having a body portion, a top surface, opposite bottom surface, a proximal and distal end. The top surface of the base is contoured to compliment the natural curve of the palm. The apparatus further includes a shaft projecting from the distal end of the handle. The shaft has a proximal and distal end. A control sphere is located on the handle. The control sphere can be moved by one or more of a user's fingers to indicate direction. An end effector is located at the distal end …

Scalar Differential Equation For Slowly-Varying Thickness-Shear Modes In At-Cut Quartz Resonators With Surface Impedance For Acoustic Wave Sensor Application, Huijing He, Jiashi Yang, John A. Kosinski

Department of Mechanical and Materials Engineering: Faculty Publications

For time-harmonic motions, we generalize a 2-D scalar differential equation derived previously by Tiersten for slowly-varying thickness-shear vibrations of AT-cut quartz resonators. The purpose of the generalization is to include the effects of surface acoustic impedance from, e.g., mass layers or fluids for sensor applications. In addition to the variation of fields along the plate thickness, which is considered in the usual 1-D acoustic wave sensor models, the equation obtained also describes in-plane variations of the fields, and therefore can be used to study the vibrations of finite plate sensors with edge effects. The equation is compared with the theory …

Nitroxide-Functionalized Graphene Oxide From Graphite Oxide, Yazmin I. Avila-Vega, Cesar C. Leyva-Porras, Marcela Mireles, Manuel Quevedo-Lopez, Javier Macossay-Torres, Jose Bonilla-Cruz

School of Integrative Biological & Chemical Sciences (Formerly Dept. of Chemistry)

A facile method for preparing functionalized graphene oxide single layers with nitroxide groups is reported herein. Highly oxidized graphite oxide (GO=90.6%) was obtained, slightly modifying an improved Hummer’s method. Oxoammonium salts (OS) were investigated to introduce nitroxide groups to GO, resulting in a one-step functionalization and exfoliation. The mechanisms of functionalization/exfoliation are proposed, where the oxidation of aromatic alcohols to ketone groups, and the formation of alkoxyamine species are suggested. Two kinds of functionalized graphene oxide layers (GOFT1 and GOFT2) were obtained by controlling the amount of OS added. GOFT1 and GOFT2 exhibited a high interlayer spacing (d0001 = 1.12nm), …

Synthesis Of Pani/Nihcf Nanocomposite Particles And Eqcm Measurement Of Ion Exchange Properties In Solutions Containing Cd2+, Yu-Jiao Yang, Xiao-Gang Hao, Xu-Li Ma, Zhong-De Wang, Zhong-Lin Zhang, Nian-Chen Han

Journal of Electrochemistry

The PANI/NiHCF nanocomposite particles were synthesized on the CNTs-modified Pt substrate by one-step co-polymerization using cyclic voltammetry. Electrochemical quartz crystal microbalance (EQCM) technique was adopted to investigate the polymerization process of the nanocomposite particles and the mechanism of ion exchange in aqueous solution containing Cd²⁺． The morphology and structure of the as-prepared composite particles were characterized by scanning electron microscope (SEM), transmission electron microscope (TEM), and Fourier transform infrared spectroscopy (FT-IR). Combined with cyclic voltammetry (CV) and energy dispersive spectroscopy (EDS), the electrochemical behavior and the mechanism of ion exchange were also investigated in electrolytes of Cd^{2+ …}

Applications Of Spectroscopic Ellipsometry In Corrosion Investigation, Ling-Jie Li, Yu-Ling He, Jing-Lei Lei, Sheng Tao Zhang

Journal of Electrochemistry

As a highly-sensitive and non-destructive in situ technique, spectroscopic ellipsometry has been widely applied in corrosion investigation to acquire the dynamic information of the “electrode-medium” interface during corrosion. This paper lays out some representative demonstrations in several established optical models used to interpret data obtained with spectroscopic ellipsometry in corrosion investigation. In addition, the latest trends in development of this technique are analyzed.

An Investigation Of Thin Films Formed On Zinc By Spectroscopic Ellipsometry, Juan Zuo, Ying Chen, Chang-Jian Lin, Andreas Erbe

Journal of Electrochemistry

The formation of natural oxide films on polycrystalline zinc surface, the growth of natural oxide films in different atmospheres, as well as the electrochemical process of metal zinc in alkaline carbonate solution, studied recently by using spectroscopic ellipsometry in our group, are introduced. The objective of this paper is to outline that the optical, electrical properties, the change and growth kinetics of zinc metal oxide film on the surface can be investigated by in-situ and ex-situ ellipsometry, which makes significant sense to evaluate the overall performance of zinc oxide layer.

Elementary Studies Of Twisted Bilayer Graphene, Branden P. Burns, Yong P. Chen

The Summer Undergraduate Research Fellowship (SURF) Symposium

In the nanotechnology field, some existing materials and applications are harmful to the environment, not efficient for certain tasks, or too expensive to be fully utilized. Graphene is a strong and cheap material that can be used to improve current nanotechnologies for more practical uses in society. Twisted bilayer graphene (TBG) is an orientation of graphene layers that exhibit different properties than regular bilayer graphene. It is made by placing a single layer of graphene on top of another at an angle with respect to the other lattice orientation. Understanding the characteristics of TBG is important to uncover more physics …

Thin Electrical Double Layer Simulation Of Micro-Electrochemical Supercapacitors, Kaitlyn Fisher, Guoping Xiong, Timothy S. Fisher

The Summer Undergraduate Research Fellowship (SURF) Symposium

The deteriorating state of the environment has drawn many people to hybrid electric vehicles. Electrochemical micro-supercapacitors are of interest in this field because of their high power density relative to other micro-power sources. However, little is known about how the properties of the electrolyte used affect the performance of such devices. The first step of this investigation was to use thermoreflectance microscopy to measure the temperature change of the electrodes while charging and discharging supercapacitor samples. The components of these samples were graphitic petal electrodes with a Ti/Au covering (for enhanced light reflectance) on a SiO₂ base, with a …

Prism - Materials Simulation Tool, Ryan Widjaja, Marisol Koslowski

The Summer Undergraduate Research Fellowship (SURF) Symposium

MEMS (Micro-electromechanical System) is a combined electrical and mechanical nano-scaled device with rapidly growing applications. We have developed a contacting radio frequency capacitive MEMS that is commonly used as capacitive switches and contact actuators in PRISM (Prediction of Reliability, Integrity and Survivability of Microsystems) lab at Purdue University. Our research team has focused on creating a simulation of MEMS’s survivability towards crazing and cracking. Our particular objective in this project is to create a tool that can help users perform complex quantitative calculations regarding the properties of different materials. This tool will generate various plots visualizing the properties, such as …

Crystalline Cellulose – Atomistic Modeling Toolkit, Mateo Gomez, Pablo Zavattieri Dr.

The Summer Undergraduate Research Fellowship (SURF) Symposium

Nature has created efficient strategies to make materials with hierarchical internal structure that often exhibit exceptional mechanical properties. One such example is found in cellulose, in fact it is eight times stronger than stainless steel and advantage is that cellulose incredibly cheap, because processing is obtained from purified wood pulp (it is environmental friendly). The most prevalent modeling technique to study the fundamental mechanical behavior of the crystalline cellulose has been Molecular Dynamics (MD). As a predictive tool, MD allows us to study the behavior of crystalline cellulose at the atomic level, and as such, it accurately predicts the crystalline …

Phase-Field Dislocation Dynamics Code Optimization, Jaime A. Perez, Marisol Koslowski

The Summer Undergraduate Research Fellowship (SURF) Symposium

The importance of the study of nanocrystalline materials has gained a huge amount of attention these years due to its extraordinary mechanical, electrical and chemical properties. One significant way to progress in this field is by simulating the behavior of the particles in nano scale, which is not only a need but a challenge due to massive interactions that occur there. The phase-field dislocation dynamics (PFDD) method has been successfully employed in the modeling of plastic deformation, creep and grain boundary sliding. In PFDD, the plastic strain and the energy are functions of phase fields that obey a set of …

Dna Based Carbon Nanotube Porphyrin Nanohybrids Molecular Recognization And Regeneration, Molly M. Riccitelli, Hanyu Zhang, Jong Hyun Choi

The Summer Undergraduate Research Fellowship (SURF) Symposium

In the search to improve solar cells, scientists are exploring new materials that will provide better current transfer. One material that has emerged as a strong contender is the single walled carbon nanotube (SWNT). Current DNA-SWNT based films combined with chromophores have poor operational lifetimes compared to commercial solar cells. Once exposed to light the chromophore begins to degrade, eventually rendering the solar cell unusable. To solve this problem, we used a method involving multiple steps. First we found which DNA sequences formed structures around the SWNT that could hold the most chromophores by using a spectrophotometer to test the …